PBX to PBX VoIP network (H.323)
|
|
- Paulina Woods
- 8 years ago
- Views:
Transcription
1 1 PBX to PBX network (H.323) When 2 or more PBXs are connected through IP network, it is possible to call extensions in other PBX using this network. This document explains how to program for above.
2 2 Request PBX user wants to call extensions in other PBXs through private network using Voice over IP in order to save charge of long distance call. VPN router has been already installed usually for PC data network. Public Telephone Company (02) Public Telephone Company (03) Public Telephone Company (08) Customer Customer Sydney Office Melbourne Office (Voice over IP) ISDN QSIG VPN Router IP Network VPN Router Dial 0/ Ext Ext Ext Ext Perth Office VPN Router Ext Ext
3 3 Solution Making a call using TIE line feature is solution. There are two dialing methods as follows. When Ext 1011 in PBX-1 calls Ext 1012, dial Recommended I/F is (H.323) or ISDN- QSIG. E1, T1 or E&M is also possible but no supplemental service except caller ID.
4 4 Programming for network without PBX Office Code (7-xx) Programming Method Flexible Numbering to use TIE Call Dialed No. to IP Address TIE to TIE Transmission Type 1 Extension Independent No Type 2 Extension Group No Type 3 Other PBX Extension Independent Yes TIE to TIE Transmission ISDN QSIG IP Network
5 5 Concept of Programming : Type 1 When dialed number is not found in extension, TIE table is applied to decide trunk group based on leading digits. When trunk group for (H.323) is selected by TIE table, DN2IP table is applied to decide IP address of destination PBX. Public Telephone Company (02) Public Telephone Company (03) Public Telephone Company (08) Sydney Office TRG1 PBX : DSP : Melbourne Office PBX : DSP : Perth Office PBX : DSP : TRG8 ISDN QSIG TRG7 IP Network TRG7 TRG7 Ext 401 Ext 101 Ext 106 Ext 112 Ext 203 Ext 124 Ext , 106 Ext No. TIE Table DN2IP Table (Dialed Number to IP Address) 112, TRG (PBX in Melbourne) TRG (PBX in Perth) TRG (PBX in Melbourne) TRG (PBX in Perth)
6 6 Programming -1 H.323 Activation for All PBXs in Sydney, Melbourne and Perth Select MPR Virtual Slot. Program -1, 2 and 3 activate H.323 features. Other trunk card such as PRI has to be installed before this programming, otherwise CO-1/2/3 are assigned to H.323 channels.
7 H.323 Activation Programming -2 for All PBXs in Sydney, Melbourne and Perth Install V-IPGW16 card (Virtual 16-ch H.323 IP Gateway card). Max.32-ch H.323 is supported using 2 cards. Click Activation Key for next programming. Batch mode does not support Activation Key button. 7
8 8 H.323 Activation Programming -3 for All PBXs in Sydney, Melbourne and Perth Assign channels for H.323 IP-GW. Default is SIP trunk for all channels. DSP card has to be installed to PBX before this programming. DSP16 provides 4-ch IP trunk (for H.323 or SIP trunk). DSP64 provides 16-ch IP trunk (for H.323 or SIP trunk). Activation key file can increase them. Maximum capacity with activation key of DSP64 is bigger than DSP16.
9 9 TIE Call if Not Ext No. Programming -4 for All PBXs in Sydney, Melbourne and Perth Activation Key (Enhanced Feature) KX-NCS3910 for NCP KX-NCS4910 for TDE KX-NCS4950 for TDE600 This programming is not required because default is enabled. Activation key is required. If dialed number is in Numbering Plan for Extension but it is NOT extension number in this PBX, TIE feature works.
10 10 TIE Call if Not Ext No. Programming -5 for All PBXs in Sydney, Melbourne and Perth This programming is not required usually because default is enough. If dialed number is in Numbering Plan for Extension but it is NOT extension number in this PBX, TIE feature works. Default of Numbering Plan for Extension is as follows. 1xx, 2xx, 3xx, 4xx, 5xx and 6xx for NCP and TDE xx to 19xx, 20xx to 29xx, 5xx and 6xx for TDE600
11 11 TIE Call if Not Ext No. Programming -6 for TDE in Sydney Remove Remove unused extension number. If dialed number is in Numbering Plan for Extension but it is NOT extension number in this PBX, TIE feature works.
12 12 TIE Call if Not Ext No. Programming -7A for PBX in Melbourne and Perth This programming is not required usually because default is enough. Any dial is routed to H.323 because default of H.323 is Trunk Group 7. Priority 2-8 is used when all channels of priority 1 is occupied.
13 13 TIE Call if Not Ext No. Programming -7B for TDE in Sydney Assign Trunk Group 8, if the other trunk such as ISDN-QSIG is Trunk Group 8.
14 14 TIE Call if Not Ext No. Programming -8 for All PBXs in Sydney, Melbourne and Perth Default of IP-GW (H.323) is Trunk Group 7. Default of other trunk is Trunk Group 1. Assign TRG8 for lines to NCP for TDE in Sydney.
15 15 DN2IP for H.323 Programming -9 for All PBXs in Sydney, Melbourne and Perth Select Shelf Property. Out of service is required before this operation or after Programming-12.
16 16 DN2IP for H.323 Programming -10 for All PBXs in Sydney, Melbourne and Perth
17 17 DN2IP for H.323 Programming -11 for All PBXs in Sydney, Melbourne and Perth Assign IP address that each PBX has. Call is routed to the IP address. PBX in Sydney does not need GW IP address for Sydney in DN2IP table actually because call is not routed from Sydney to Sydney (loop back) usually. But same programming for all PBXs is easy to program. It is possible to export this data from one PBX and import to other PBXs using PCMC.
18 DN2IP for H.323 Programming -12 for All PBXs in Sydney, Melbourne and Perth DN2IP Table (Dialed Number to IP Address) 101, (PBX in Sydney) (PBX in Melbourne) (PBX in Perth) (PBX in Melbourne) (PBX in Perth) It is possible to export this data from one PBX and import to other PBXs using PCMC. Remaining Number allows call without timeout. Ext 305 can be called through after dialing 305 without timeout. 18
19 19 DN2IP for H.323 Programming -13 for All PBXs in Sydney, Melbourne and Perth Default is to receive any call to this PBX. Default is OK. For example, if 8 is not programmed, call to 8xx is rejected.
20 20 DN2IP for H.323 Programming -14 for All PBXs in Sydney, Melbourne and Perth Change status to OUS (Out of Service) and return to INS (In Service). This is required to activate setting and activation key.
21 21 Programming for network without PBX Office Code (7-xx) Programming Method Flexible Numbering to use TIE Call Dialed No. to IP Address TIE to TIE Transmission Type 1 Extension Independent No Type 2 Extension Group No Type 3 Other PBX Extension Independent Yes Type 1 is easy to understand specifications. Type 2 is easy to program usually. So type 2 is used for programming usually instead of type 1.
22 Concept of Programming : Type 2 22 Public Telephone Company (02) Public Telephone Company (03) Public Telephone Company (08) Sydney Office TRG1 PBX : DSP : Melbourne Office PBX : DSP : Perth Office PBX : DSP : TRG8 ISDN QSIG TRG7 IP Network TRG7 TRG7 Ext 401 Ext 101 Ext 203 Ext 112 Ext 106 Ext 124 Ext 305 Type 1 DN2IP Table (Dialed Number to IP Address) Type 2 : All PBXs are assigned as destination for any dials. DN2IP Table (Dialed Number to IP Address) (PBX in Sydney) (PBX in Sydney) (PBX in Sydney) 1 or 2 or 3 IP-GW Group (PBX in Melbourne) (PBX in Melbourne) (PBX in Perth) (PBX in Melbourne) (PBX in Perth) (PBX in Perth) DN2IP table has 100 entries. If Ext 124 of PBX in Perth dials 106. (1) Perth cannot find 106 in extension. (2) Perth asks to Sydney. Do you have 106? Reply from Sydney. No. (3) Perth asks to Melbourne Do you have 106? Reply from Melbourne. Yes => Ring starts.
23 23 Programming -21 for All PBXs in Sydney, Melbourne and Perth Assign all PBXs in same group. Program -21, 22 and 23 are required instead of Program -11 and 12. Other programming is same as type 1.
24 24 Programming -22 for All PBXs in Sydney, Melbourne and Perth Destination is NOT one PBX (GW No.) but GW Group. Program -21, 22 and 23 are required instead of Program -11 and 12. Other programming is same as type 1.
25 25 Programming -23 for All PBXs in Sydney, Melbourne and Perth For 3 or more than 3 PBXs, this programming is required. Otherwise operator of 1st other PBX will ring for call to 2nd or later PBX.
26 26 Programming for network without PBX Office Code (7-xx) Programming Method Flexible Numbering to use TIE Call Dialed No. to IP Address TIE to TIE Transmission Type 1 Extension Independent No Type 2 Extension Group No Type 3 Other PBX Extension Independent Yes TIE to TIE Transmission ISDN QSIG IP Network
27 27 Concept of Programming : Type 3 Flexible Numbering Other PBX Ext No. is used for TIE call. TIE to TIE transmission is available using this type. Public Telephone Company (02) Public Telephone Company (03) Public Telephone Company (08) Sydney Office Ext 401 TRG8 ISDN QSIG Ext 101 TRG1 PBX : DSP : Ext 106 Dial 401 TRG7 Dial 401 IP Network Melbourne Office PBX : DSP : TRG7 Dial 401 Ext 112 Ext 203 Perth Office PBX : DSP : TRG7 Ext 124 Ext 305 TDE in Sydney TDE in Melbourne NCP in Perth Ext No. Other PBX Ext No. Ext No. Other PBX Ext No. Ext No Other PBX Ext No. If received dial from other PBX is Other PBX Ext No., TIE table and DN2IP table are applied, as well as dial from extension. Flexibility of extension number is low. TDE in Sydney can have extension 10x only for example.
28 28 Programming -31 for TDE in Sydney This programming is required instead of Program -4, 5 and 6. Other programming is same as type 1.
29 29 DN2IP for H.323 Programming -32 for All PBXs in Sydney, Melbourne and Perth Sydney Office Melbourne Office TRG8 ISDN QSIG TRG7 IP Network Dial 101 TRG7 Dial or 4 to Sydney Ext 401 Ext 101 Ext 106 Ext 112 Ext 203
30 30 Programming for network with PBX Office Code (7-xx) TIE to TIE Transmission : Yes TIE to TIE Transmission ISDN QSIG IP Network
31 31 Concept of Programming : PBX Code PBX office code is programmed for TIE table and DN2IP table. Public Telephone Company (02) Public Telephone Company (03) Public Telephone Company (08) Sydney Office 7-21 TRG TRG8 ISDN QSIG Dial TRG7 Dial IP Network Melbourne Office 7-30 PBX : DSP : PBX : DSP : TRG7 Dial Perth Office 7-81 PBX : DSP : TRG7 Ext 101 Ext 101 Ext 102 Dial 101 Ext 101 Ext 102 Ext 101 Ext 102 TIE table and DN2IP table are applied to dial from other PBX, as well as dial from extension after removing 7. Dial from Ext Dial from other PBX TIE Table DN2IP Table (Dialed Number to IP Address) TRG (PBX in Melbourne) TRG (PBX in Perth) TRG My PBX Code = 22 Ext 101 in PBX in Sydney is called, because dial 22 is My PBX code.
32 32 Programming -41 for All PBXs in Sydney, Melbourne and Perth 7 is programmed by default for TIE line access. Program -4, 5 and 6 of type 1 are not required.
33 33 Programming -42A for TDE in Sydney Program Own PBX Code to 22. PBX office code is programmed instead of Program -7 of type to TRG8 Other 7-xx to TRG7
34 34 Programming -42B for PBX in Melbourne and Perth Program Own PBX Code to 30 for Melbourne and 81 for Perth. Program Any 7-xx to TRG7. (This is programmed by default.)
35 35 Programming -43 for All PBXs in Sydney, Melbourne and Perth PBX office code is programmed instead of Program -7 of type 1. Call between NCP in Sydney (7-21) and PBX in Melbourne or Perth is possible through TDE in Sydney (7-22), if PBX office code is used.
36 Remark 36
37 37 Remark A Usually GW setting and DN2IP are common for all PBXs. It is convenient to export data from one PBX and import to other PBXs.
38 38 Remark - B Do not forget programming of Default Gateway for actual installation. Setting is same as PC installed in same network. This is not required for demo in one LAN hub. Office LAN IP Address of PC : Subnet Mask : Default Gateway :
39 39 Programming Method Remark - C Flexible Numbering to use TIE Call Dialed No. to IP Address *1) This can be changed to Yes by system reserved bit This provide following solution for example. TIE to TIE Transmission Type 1 Extension Independent No *1 Type 2 Extension Group No Type 3 Other PBX Extension Independent Yes Sydney Office 10x or 4xx Only TDE uses this bit. NCP TIE Table TDE TIE Table 1 TRG8 10 TRG8 2 TRG8 11 TRG7 3 TRG8 12 TRG7 4 TRG8 2 TRG7 3 TRG7 4 TRG8 It is also possible for NCP in Sydney to call other offices through TDE in Sydney. TIE table and DN2IP table of TDE in Sydney are applied to dial from other PBX, as well as dial from extension. Melbourne Office 2xx or 11x Perth Office 3xx or 12x TRG8 ISDN QSIG Dial 102 TRG7 Dial 101 IP Network TRG7 Dial 101 TRG7 Dial 102 Ext 102 Ext 401 Ext 101 Ext 106 Dial 101 Ext 112 Ext 203 Ext 124 Ext 305
40 40 Programming Method Remark D Flexible Numbering to use TIE Call Dialed No. to IP Address TIE to TIE Transmission Type 1 Extension Independent No *1 Type 2 Extension Group No *2 Type 3 Other PBX Extension Independent Yes *1) This can be changed to Yes by system reserved bit But if both TDE and NCP use this bit for following example, all channels between PBXs are occupied temporally (and released automatically) for incorrect dial such as 104. Ext 102 Ext 401 Ext 101 Ext 106 Dial 104 Both TDE and NCP think I do not have ext 104, I have to make a TIE call. *2) System reserved bit 02-5 should not be used for type 2. If this is enabled, making a TIE call starts instead of replying I do not have the ext. See Concept of Programming : Type 2.
41 41 Programming Method Remark E Flexible Numbering to use TIE Call Dialed No. to IP Address Type 1 Extension Independent Type 2 Extension Group Type 3 Other PBX Extension Independent Activation Key (Enhanced Feature) KX-NCS3910 for NCP KX-NCS4910 for TDE KX-NCS4950 for TDE600 Features Without PBX Office Code Type 1 Type 2 Type 3 With PBX Office Code Calling extension in other PBX Yes *1 Yes *1 Yes Yes TIE to TIE transmission Yes *1 *2 No Yes Yes Network ICD Group Yes *1 Yes *1 Yes *1 Yes *1 Network DSS key No No Yes *1 Yes *1 Centralized VM Yes *1 *3 Yes *1 *3 Yes *1 Yes *1 Version 4 enhanced network features Yes *1 Yes *1 Yes *1 Yes *1 *1) One activation key is required for all features. (Not one key for each one feature) *2) System reserved bit is required as previous page. *3) Destination of VM has to use type 3. Other extensions can be called using type 1 or 2.
42 End of Document 42
Panasonic KX-NCP500 KXNCP500 KX NCP500 KX-NCP1000 KXNCP1000 KX NCP1000
Model No. KX-NCP500 KX-NCP1000 www.voicesonic.com Phone 877-289-2829 IP Networking Guide Pure IP-PBX Panasonic KX-NCP500 KXNCP500 KX NCP500 KX-NCP1000 KXNCP1000 KX NCP1000 Thank you for purchasing a Panasonic
More informationSetup Reference guide
Setup Reference guide for KX-NS1000 to E1 PRI/R2 Gateway interconnection Panasonic PBX (KX-NS1000 series), Media5 Digital Gateway 3631(Mediatrix 3000 series) Revision 0.2(PSNJ) October.14, 2012 Attention:
More informationIP Networking Guide KX-TDE200/KX-TDE600. Pure IP-PBX. Model No. KX-TDE100
IP Networking Guide Pure IP-PBX Model No. KX-TDE100 KX-TDE200/KX-TDE600 Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual
More informationThank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use.
IP Networking Guide Pure IP-PBX Model No. KX-NCP500/KX-NCP1000 KX-TDE100/KX-TDE200/KX-TDE600 Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product
More informationGetting Started KX-TDA5480
4-Channel VoIP Gateway Card Getting Started KX-TDA5480 Model KX-TDA0484 Thank you for purchasing the Panasonic 4-Channel VoIP Gateway Card, KX-TDA5480/KX-TDA0484. Please read this manual carefully before
More informationGetting Started. 16-Channel VoIP Gateway Card. Model No. KX-TDA0490
16-Channel VoIP Gateway Card Getting Started Model No. KX-TDA0490 Thank you for purchasing a Panasonic 16-Channel VoIP Gateway Card. Please read this manual carefully before using this product and save
More informationKX-NS. Cellular Phone as Extension
KX-NS Cellular Phone as Extension Introduction Cellular phone can work as extension. Even when your important customer calls your office phone number and you are out of office, you can answer the call
More informationGetting Started for Virtual IP Cards
Panasonic Telephone Systems Panasonic KX-TDE100 KX-TDE200 www.voicesonic.com Phone: 877-289-2829 Getting Started for Virtual IP Cards Pure IP-PBX Panasonic KX-TDE100, KXTDE100, TDE100, KX-TDE200, KXTDE200,
More informationGetting Started. 16-Channel VoIP Gateway Card. Model No. KX-TDA0490
16-Channel VoIP Gateway Card Getting Started Model No. KX-TDA0490 Thank you for purchasing a Panasonic 16-Channel VoIP Gateway Card. Please read this manual carefully before using this product and save
More informationSetup Reference guide for PBX to SBC interconnection
Setup Reference guide for PBX to SBC interconnection Method of connection by "LAN interface only" i.e. SBC is placed behind the Perimeter Router / Fire-wall. Panasonic PBX (KX-TDE, NCP series), Media5
More informationIntegra Telecom SIP Trunks Configuration Guide PBX Platform: KX-TDE/NCP
Integra Telecom SIP Trunks Configuration Guide PBX Platform: KX-TDE/NCP 7/13/2011 1 Overview This document describes the configuration procedures required for the KX-TDE100/200/600 and NCP500/1000 to make
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Panasonic KX-NCP500 IP PBX V2.0502
PANASONIC SIP Trunking using Optimum Business SIP Trunk Adaptor and the Panasonic KX-NCP500 IP PBX V2.0502 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More informationSetup Reference Guide for KX-TDE/NCP to SBC SIP Trunking
Setup Reference Guide for KX-TDE/NCP to SBC SIP Trunking Method of connection by "WAN Global IP address directly" (i.e. SBC is the Perimeter Router device.) Panasonic IP-PBX (KX-TDE/NCP Version6 series),
More informationPanasonic KX-TDE100/200/600 Pure IP-PBX Cross Training
Panasonic KX-TDE100/200/600 Pure IP-PBX Cross Training Specifications subject to change without notice XTraining TDE2.0_112909A 1 KX-TDE100 System Outline The KX-TDE100 consists of the Basic Shelf with:
More informationThank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use.
Panasonic Telephone Systems KX-TDE100 KX-TDE200 KX-TDE600 www.voicesonic.com Phone: 877-289-2829 IP Networking Guide Pure IP-PBX Panasonic KX-TDE100, KXTDE100, TDE100, KX-TDE200, KXTDE200, TDE200, KX-TDE600,
More informationPanasonic NCP Features and Functions
Panasonic Telephone Systems Panasonic KX-NCP500 Panasonic KX-NCP1000 http://www.voicesonic.com Phone: 877-289-2829 Panasonic NCP Features and Functions Dealer Sales Training Program Panasonic KX-NCP500,
More informationThank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use.
IP Networking Guide Model No. Pure IP-PBX KX-NCP500 KX-NCP1000 Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future
More informationSetup Reference Guide for KX-NS1000 to SBC SIP Trunking
Setup Reference Guide for KX-NS1000 to SBC SIP Trunking Method of connection by "WAN Global IP address directly" (i.e. SBC is the Perimeter Router device.) Panasonic IP-PBX (KX-NS1000 Version2 series),
More informationConfiguration Guide for connecting the Eircom Advantage 4800/1500/1200 PBXs to the Eircom SIP Voice platform.
Configuration Guide for connecting the Eircom Advantage 4800/1500/1200 PBXs to the Eircom SIP Voice platform. 1 Contents Introduction.... 3 Installing the Applications Module... 4 Ordering a Licence for
More informationConfiguration of Applied VoIP Sip Trunks with the Toshiba CIX40, 100, 200 and 670
Configuration of Applied VoIP Sip Trunks with the Toshiba CIX40, 100, 200 and 670 Businesses Save Money with Toshiba s New SIP Trunking Feature Unlike gateway based solutions, Toshiba s MIPU/ GIPU8 card
More informationHow To Configure An African Atlas
Configuring the ATLAS for a Primary Rate ISDN (PRI) to T1 Robbed Bit Signaling (RBS) Conversion Introduction The ADTRAN ATLAS 550/800/800 PLUS supports both Primary Rate ISDN (PRI) and T1 Robbed Bit Signaling
More informationSIP Proxy Server. Administrator Installation and Configuration Guide. V2.31b. 09SIPXM.SY2.31b.EN3
SIP Proxy Server Administrator Installation and Configuration Guide V2.31b 09SIPXM.SY2.31b.EN3 DSG, DSG logo, InterPBX, InterServer, Blaze Series, VG5000, VG7000, IP590, IP580, IP500, IP510, InterConsole,
More informationDocument for Technical and Sales Training. KX-NS300 Basic Specification
Document for Technical and Sales Training 300 Basic Specification 1. Introduction (PBX Line-up) 300 is successor of KX-TDA/TDE100-200 and KX-NCP with built-in solution based on 1000. Max. Ext NS IP/Digital
More information2N NetStar. 2N NetStar as a PBX Booster. Quick guide. www.2n.cz. Version 1.00
2N NetStar 2N NetStar as a PBX Booster Quick guide Version 1.00 www.2n.cz How to set up 2N NetStar as a PBX booster? This how to manual will help you to set up 2N NetStar as a PBX booster. NetStar is connected
More informationMAX T1/E1. Quick Start Guide. VoIP Gateway. Version 1.0
MAX T1/E1 TM VoIP Gateway Quick Start Guide Version 1.0 Contents INTRODUCTION 1 Hardware Needed Software Needed 1 1 NET2PHONE MAX SET UP Hardware Set Up Software Set Up Set Up Internet Protocol (IP) Address
More informationInternet Telephony PBX System
Internet Telephony PBX System IPX-600 Copyright PLANET Technology Corporation. All rights reserved. This installation guide introduces several practical configuration examples of IP PBX deployment. The
More informationHow to Connect MyPBX to NeoGate TG via SIP Trunking
How to Connect MyPBX to NeoGate TG via SIP Trunking Version: 1.0 Yeastar Technology Co., Ltd. Date: 2013.11.16 http://www.yeastar.com 1/11 Contents: 1. Introduction... 3 2. Connect MyPBX to NeoGate TG...
More informationSIP Trunk Configuration Guide. using
SIP Trunk Configuration Guide using www.cbeyond.net 1-877-441-9783 The information contained in this document is specific to setting up SIP connections between Vertical SBX IP 320 and Cbeyond. If you require
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1
ALLWORX SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1 Goal The purpose of this configuration guide is to describe the steps needed to configure the Allworx 6x
More informationSetup Reference Guide for KX-NS1000 to SBC interconnection
Setup Reference Guide for KX-NS1000 to SBC interconnection Method of connection by "WAN Global IP address directly" (i.e. SBC is the Perimeter Router device.) Panasonic IP-PBX (KX-NS1000 Version2 series),
More informationInternet Telephony PBX System
Internet Telephony PBX System T1/E1 Gateway With IP PBX Application Copyright PLANET Technology Corporation. All rights reserved. Case 35: With IP PBX Application Head Office E1 PABX interconnect with
More informationBusinesses Save Money with Toshiba s New SIP Trunking Feature
TOSHIBA Strata CIX Product Bulletin PBCIX-0056 Dec. 7, 2007 Businesses Save Money with Toshiba s New SIP Trunking Feature For business trying to save money on telecommunications tariffs, conventional technology
More informationESI SIP Trunking Installation Guide
ESI SIP Trunking Installation Guide 0450-1227 Rev. B Copyright 2009 ESI (Estech Systems, Inc.). Information contained herein is subject to change without notice. ESI products are protected by various U.S.
More informationSmartPTT Tutorial Telephone Interconnect
SmartPTT Tutorial Telephone Interconnect Telephone Interconnect Overview Telephone Interconnect is the service included into SmartPTT Radioserver to establish interconnection between Radio and Telephone
More informationQuick Installation Guide
Quick Installation Guide PRI Gateway Version 2.4 Table of Contents Hardware Setup... 1 Accessing the WEB GUI... 2 Notification LEDs (On the Front Panel of the Gateway)... 3 Creating SIP Trunks... 4 Creating
More informationTech Bulletin 2012-002. IPitomy AccessLine SIP Provider Configuration
support@ipitomy.com 941.306.2200 Tech Bulletin 2012-002 Description This guide is intended to streamline the installation of AccessLine SIP trunks in the IPitomy IP PBX. In our combined testing we determined
More informationDigium Switchvox AA65 PBX Configuration
Digium Switchvox SIP Trunking using Optimum Business SIP Trunk Adaptor and the Digium Switchvox AA65 IP-PBX v23695 Goal The purpose of this configuration guide is to describe the steps needed to configure
More informationOptimum Business SIP Trunk Set-up Guide
Optimum Business SIP Trunk Set-up Guide For use with IP PBX only. SIPSetup 07.13 FOR USE WITH IP PBX ONLY Important: If your PBX is configured to use a PRI connection, do not use this guide. If you need
More informationCall Centre Solutions
Call Centre Solutions When Every Call Matters Topics of Discussion What happens when a call arrives Panasonic s Call Distribution Methods What happens when all the members / agents are busy or not available
More informationAudioCodes Mediant 1000 Configuration Guide
AudioCodes Mediant 1000 Configuration Guide 2010 FaxBack, Inc. All Rights Reserved. NET SatisFAXtion and other FaxBack products, brands and trademarks are property of FaxBack, Inc. Other products, brands
More informationApplication Notes for Multi-Tech FaxFinder IP with Avaya IP Office Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Multi-Tech FaxFinder IP with Avaya IP Office Issue 1.0 Abstract These Application Notes describe the configuration steps required to integrate
More informationTech Bulletin 2011-004 IPitomy Paetec SIP Provider Configuration
Tech Bulletin 2011-004 Description This guide is intended to streamline the installation of Paetec SIP trunks in the IPitomy IP PBX. Procedure Add Provider 1. Navigate to the IPitomy IP PBX web interface
More informationSetup Reference Guide for KX-NS1000 to SBC interconnection
Setup Reference Guide for KX-NS1000 to SBC interconnection Method of connection by "LAN interface only" i.e. SBC is placed behind the Perimeter Router / Fire-wall. Panasonic IP-PBX (KX-NS1000 Version2
More informationOperation Manual Voice Overview (Voice Volume) Table of Contents
Operation Manual Voice Over (Voice Volume) Table of Contents Table of Contents Chapter 1 Voice Over... 1-1 1.1 Introduction to VoIP... 1-1 1.1.1 VoIP System... 1-1 1.1.2 Basic VoIP Call Flow... 1-2 1.1.3
More informationSIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX
June 26th, 2014 SIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX Page 1 of 30 Table of Contents 1 Overview... 3 2 Prerequisites... 3 3 Network Topology... 4 4 Description
More informationHow to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions
How to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Toshiba Strata CIX IP PBX to connect to Integra
More informationHow To Connect To A Ppanasonic Pbx On A Pc Or Mac Or Ipa (For A Pc) With A Usb Or Ipo (For Mac) With Pbq (For Pc) On A Usb (For Pb
R KX-Series PBX TAPI Service Provider Installation Manual Revision: 4.0.0.1 October 2011 Introduction About TSP Panasonic TAPI Service Provider for TDA/TDE/NCP/NS Series PBX (Panasonic TSP) is a driver
More informationGW400 VoIP Gateway. User s Guide
GW400 VoIP Gateway User s Guide P/N: 956YD30001 Copyright 2006. All Rights Reserved. Document Version: 1.0 All trademarks and trade names are the properties of their respective owners. i Table of Contents
More informationMAXCS Release 7.0. Application Note: Remote MultiVoIP Gateway Configuration. Intended audience: AltiGen Authorized Partners
MAXCS Release 7.0 Application Note: Remote MultiVoIP Gateway Configuration Intended audience: AltiGen Authorized Partners March 4, 2014 Contents Introduction... 3 Requirements... 3 MultiVoIP Gateway Configuration...
More informationH.323 / SIP VoIP Gateway VIP GW. Quick Installation Guide
H.323 / SIP VoIP Gateway VIP GW Quick Installation Guide Overview This quick installation guide describes the objectives; organization and basic installation of the PLANET VIP-281/VIP-480/VIP-880/VIP-1680/VIP-2480
More informationConfiguring the ADTRAN ATLAS for a Rabbit-Hole Application
Configuring the ADTRAN ATLAS for a Rabbit-Hole Application Description: This configuration allows an ADTRAN ATLAS to convert PRI to FXS and pass ANI/DNIS information as DTMF digits toward a receiver in
More informationeircom advantage VoIP Netwrorking Configuration Guide
eircom advantage VoIP Netwrorking Configuration Guide eircom Operaadvantage VoIP Networking configuration guide Guide VoIP Networking Configuration 1 eircom advantagevoip Networking Configuration Guide
More informationEnabling NAT and Routing in DGW v2.0 June 6, 2012
Enabling NAT and Routing in DGW v2.0 June 6, 2012 Proprietary 2012 Media5 Corporation Table of Contents Introduction... 3 Starting Services... 4 Distinguishing your WAN and LAN interfaces... 5 Configuring
More informationTech Bulletin 2011-003. IPitomy MegaPath SIP Provider Configuration
Description This guide is intended to streamline the installation of MegaPath (a.k.a. Speakeasy and Covad) SIP Trunks in the IPitomy IP PBX. Procedure Add Provider 1. Navigate to the IPitomy IP PBX web
More informationConfiguration Notes 283
Mediatrix 4400 Digital Gateway VoIP Trunking with a Legacy PBX June 21, 2011 Proprietary 2011 Media5 Corporation Table of Contents Table of Contents... 2 Introduction... 3 Mediatrix 4400 Digital Gateway
More informationApplication Notes for MultiTech FaxFinder IP with Avaya IP Office Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for MultiTech FaxFinder IP with Avaya IP Office Issue 1.0 Abstract These Application Notes describe the configuration steps required to integrate
More informationEZLoop IP-PBX Enterprise SIP Server
EZLoop IP-PBX Enterprise SIP Server Copyright 2007 Teletronics International, Inc. 2 Choke Cherry Road, Rockville, MD 20850 sales@teletronics.com www.teletronics.com CH1. Overview...4 1.1 Specifications...4
More informationNetVanta 7060/7100 Configuration Checklist
NetVanta 7060/7100 Configuration Checklist AOS Versions Supported: AOS A1.01.00 and above. AOS Versions Supporting SIP Trunking and Networking: AOS A2.02.00 and above. This document is designed to provide
More informationTechnical Information
KX-TDE100 KX-TDE200 KX-TDE600 KX-NCP500 KX-NCP1000 www.voicesonic.com Phone 877-289-2829 Technical Information DATE: WEDNESDAY SEPTEMBER 3, 2008 DOCUMENT NO. TN-KXTUPCMC-0408-1 Title: BroadVox SIP CO Line
More informationMediatrix 3000 with Asterisk June 22, 2011
Mediatrix 3000 with Asterisk June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 Network Topology... 3 Equipment Detail... 3 Configuration of the Fax Extension... 4 Configuration
More informationInternet Telephony PBX System. IPX-300 Series. Quick Installation Guide
Internet Telephony PBX System IPX-300 Series Quick Installation Guide Overview PLANET IPX-300/IPX-300W IP PBX telephony systems ( IP PBX in the following term) are designed and optimized for the small
More informationAllo PRI Gateway and Elastix Server
Allo PRI Gateway and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single Allo PRI Gateway configuration. We re going to configure a SIP Trunk
More informationPanasonic KX-NCP500, KXNCP500, NCP500, KX-NCP1000, KXNCP1000, NCP1000
Model No. KX-NCP500 KX-NCP1000 www.voicesonic.com Phone 877-289-2829 Feature Manual Pure IP-PBX Panasonic KX-NCP500, KXNCP500, NCP500, KX-NCP1000, KXNCP1000, NCP1000 Thank you for purchasing a Panasonic
More informationRelease Notes for NeoGate TE100 16.18.0.X
Release Notes for NeoGate TE100 16.18.0.X ===Firmware Version: V16.18.0.2==== Applicable Model: NeoGate TE100 Release Date: October 25th, 2014 http://www.yeastar.com 1/6 1. New Features 1. Added support
More informationHow to Configure the Avaya IP Office 6.1 for use with Integra Telecom SIP Solutions
How to Configure the Avaya IP Office 6.1 for use with Integra Telecom SIP Solutions Overview This document provides a reference for configuration of the Avaya IP Office to connect to Integra Telecom SIP
More informationConfiguring Avaya IP Office 500 for Spitfire SIP Trunks
Configuring Avaya IP Office 500 for Spitfire SIP Trunks This document is a guideline for configuring Spitfire SIP trunks onto Avaya IP Office 500 and includes the settings required for Inbound DDI routing
More informationIntegrated Voice. Service Guide. www.megapath.com. Learn More: Call us at 877.634.2728. Save money and maximize bandwidth efficiency
Service Guide Save money and maximize bandwidth efficiency Learn More: Call us at 877.634.2728. www.megapath.com Table of Contents Product overview... 3 What is integrated voice?... 3 How it works... 4
More informationUX5000 with CommPartners SIP Trunks
UX5000 with CommPartners SIP Trunks SECTION 1 NEC S UX5000 AND CommPartners SETUP GUIDE This guide provides example entries for the required fields. The actual data will be e- mailed to you in the following
More informationHow to use IP-0x to connect to Skype
How to use IP-0x to connect to Skype Product Guide Version: 1.0 2010-10-14 Content CONTACT ATCOM... 2 HOW TO USE IP-0X TO CONNECT TO SKYPE... 2 YOU NEED TO SIGN UP A SKYPE MANAGER ACCOUNT.... 2 REGISTER
More informationFonality. Optimum Business Trunking and the Fonality Trixbox Pro IP PBX Standard Edition V4.1.2- p13 Configuration Guide
Fonality Optimum Business Trunking and the Fonality Trixbox Pro IP PBX Standard Edition V4.1.2- p13 Configuration Guide Fonality Table of Contents 1. Overview 2. SIP Trunk Adaptor Set-up Instructions 3.
More informationMediatrix 4404 Step by Step Configuration Guide June 22, 2011
Mediatrix 4404 Step by Step Configuration Guide June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents First Steps... 3 Identifying your MAC Address... 3 Identifying your Dynamic IP Address...
More informationIntercommunication between two MyPBX (via VoIP Trunk)
Intercommunication between two MyPBX (via VoIP Trunk) 1. Link two MyPBX in the same network... 2 2. Link two MyPBX in different location... 6 2.1 Link two MyPBX via IAX Trunk... 7 2.2 Link two MyPBX via
More informationOpera VoIP Networking Configuration Guide
VoIP Netwrorking Configuration Guide Opera VoIP Networking Configuration Guide 1 VoIP Networking Configuration Guide Specifications subject to change without notice. DM-983 Draft 2 VoIP Netwrorking Configuration
More informationConverged Voice Service Summary
SERVICE DELIVERY OVERVIEW Zayo Enterprise Networks (ZEN) offers a managed converged voice and Internet solution for businesses owning and managing a premise-based KTS or PBX system. Voice and Internet
More informationGetting Started. Pure IP-PBX. Model No. KX-NS1000
Getting Started Pure IP-PBX Model No. KX-NS1000 Thank you for purchasing this Panasonic product. Please read this manual carefully before using this product and save this manual for future use. KX-NS1000:
More informationVoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
VoiceGear/3CX Integration Guide Ver.0.1 Page 2 1. OVERVIEW... 3 1.1 SETTING UP 3CX PBX...4 1.2 SETTING UP VOICEGEAR GATEWAY...5 2. VOICEGEAR-3CX SIP INTEGRATION... 6 2.1 3CX CONFIGURATION...7 2.2 VOICEGEAR
More informationScopTEL TM IP PBX Software. Managing Incoming Lines
Managing Incoming Lines Incoming Lines Incoming Lines must be created to Route incoming calls to required destinations From Configuration > Telephony > Lines > Incoming Lines Click on Add a new Incoming
More informationSIPSTATION User Guide. Schmooze Com Inc.
Schmooze Com Inc. Chapters Overview Logging In & Adding a Key Account Settings Route & Trunk Configuration DID Configuration Recap Overview The SIPSTATION module, when combined with a SIPSTATION SIP Trunk
More informationNetworking Basics for Automation Engineers
Networking Basics for Automation Engineers Page 1 of 10 mac-solutions.co.uk v1.0 Oct 2014 1. What is Transmission Control Protocol/Internet Protocol (TCP/IP)------------------------------------------------------------
More informationJenne TTS. IP Office. Scrapbook. Of Job Aids
Jenne TTS IP Office Scrapbook Of Job Aids Table of Contents Page Topic 3 1 - Basic IP Office Punch list 4 2 - Most wanted Short Codes 7 3 - IP Office upgrade procedure 8 4 - Small community Networking
More information3CX PBX v12.5. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5 Table of Contents 1. Overview 3 2. Prerequisites 3 3. PBX Configuration 3 4. Creating Extensions 4 5. VoIP Provider Setup
More informationSIP Trunking with Elastix. Configuration Guide for Matrix SETU VTEP
SIP Trunking with Elastix Configuration Guide for Matrix SETU VTEP Contents Setup Diagram 3 SIP Trunk Configuration in Elastix for SETU VTEP 4 Outgoing Call configuration in Elastix 7 Incoming call configuration
More informationConfiguring SSH Sentinel VPN client and D-Link DFL-500 Firewall
Configuring SSH Sentinel VPN client and D-Link DFL-500 Firewall I. Configuring D-Link DFL-500 Firewall 1. Connect your computer to the internal port of the DFL-500 Firewall 2. Change the computer IP address
More informationCopyright ZYCOO All Rights Reserved 1 / 8
Copyright ZYCOO All Rights Reserved 1 / 8 If you have a scenario where you have two CooVox IP PBXs in two different locations then you can integrate them together to make free phone calls between locations.
More informationVoIP Application Note:
VoIP Application Note: Configure NEC UX5000 w/ BroadVox SIP Trunking Service P/N 0913226 Date: 8/12/09 Table of Contents: GOAL... 3 PREREQUISITES... 3 SIP TRUNKING INFORMATION PROVIDED BY BROADVOX:...
More informationIntercommunication between two MyPBX (via VoIP Trunking)
Intercommunication between two MyPBX (via VoIP Trunking) 1. Connect two MyPBX in the same network... 2 2. Connect two MyPBX in different locations... 8 2.1 Connect two MyPBX via SIP Trunking... 9 2.2 Connect
More informationAvaya IP Office 8.1 Configuration Guide
Avaya IP Office 8.1 Configuration Guide Performed By tekvizion PVS, Inc. Contact: 214-242-5900 www.tekvizion.com Revision: 1.1 Date: 10/14/2013 Copyright 2013 by tekvizion PVS, Inc. All Rights Reserved.
More informationMyPBX Client User Manual
MyPBX Client User Manual Version 1.0.0.4 Yeastar Information Technology Co. Ltd Table of Contents PART 1 HOW TO ACTIVATE MYPBX CLIENT ADDON... 4 1 ACTIVATE MYPBX CLIENT ADDON... 4 2 MYPBX CLIENT ADDON
More informationConfiguration of the Intertex IX78 E-SBC with IP-PBXs and Telia SIP Trunking Services
2010-03-07 Configuration of the Intertex IX78 E-SBC with IP-PBXs and Telia SIP Trunking Services For the IX78 ADSL T8 GW2 model with Telia SIP-anslutning using Telia Bredband Företag or Telia ProLane Table
More informationYeastar Technology Co., Ltd.
Client Manual 1.0.0.4 (English Version) Yeastar Technology Co., Ltd. Table of Contents MyPBX Client Manual Part 1 How To Activate MyPBX Client Addon 4 1 Activate MyPBX Client Addon 4 2 MyPBX Client Addon
More informationZyXEL IP PBX Support Note. ZyXEL IP PBX (X2002) VoIP. Support Notes
ZyXEL IP PBX (X2002) VoIP Support Notes Version 1.00 October 2008 1 Contents Overview ZyXEL IP PBX Support Note 1. How to manage and maintain your IPPBX?...3 1.1 Firmware Upgrade..3 1.2 Backing up your
More informationbusiness communications server KX-ns1000 Discover a world of benefits in one business communications solution.
business communications server Discover a world of benefits in one business communications solution. An IP Platform to Deliver Business Communication INTRODUCING THE PANASONIC In the current era Business
More informationDID Destinations are as follows:
IPedge Feature Desc. 1/31/13 OVERVIEW Direct Inward Dialing (DID) Direct Inward Dialing is a feature offered by telephone service providers for use with their customers' PBX systems. The telephone service
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More informationIPPBX User Quick Start
Datasheet IPPBX User Quick Start 1. Package Content GLIDERVOX Machine 1 (take 4FXO,4FXS as example) Power Adapter (12V / 2A) 1 Quick Start Manual 1 2. Application Topology The 8 LAN ports are used for
More informationSIP Trunking using the Optimum Business SIP Trunk Adaptor and the FortiVoice IP-PBX
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the FortiVoice IP-PBX 1 Table of Contents 1. Overview 3 2. Prerequisites 3 3. FortiVoice Configuration 3 3.1 Global Settings 4 3.2 SIP Registration
More informationSIP Trunking Service Configuration Guide for MegaPath
Notice Note that when converting this document from its original format to a.pdf file, some minor font and format changes may occur. When viewing and printing this document, we cannot guarantee that your
More informationIP PBX. SD Card Slot. FXO Ports. PBX WAN port. FXO Ports LED, RED means online
1 IP PBX SD Card Slot FXO Ports PBX LAN port PBX WAN port FXO Ports LED, RED means online 2 Connect the IP PBX to Your LAN Internet PSTN Router Ethernet Switch FXO Ports 3 Access the PBX s WEB GUI The
More informationCisco Unified Communications Express - Quick Configuration Tool User Guide
Cisco Unified Communications Express - Quick Configuration Tool User Guide Revised: October 12, 2006 First Published: November 2005 This guide describes how to use the Cisco Unified Communications Express
More informationThis document is an application note for connecting the GS8 modular gateway with Zed-3 SE family IP PBX.
Zed-3 501 Valley Way Milpitas CA 95035 USA GS8 Modular Gateway Connecting to the SE Family IP PBX Voice: +1-408-587-9333 Fax: +1-408-586-9038 www.zed-3.com Application note, 96-90000-00, July 2008 This
More information