Mini slide, Series MSN narrow version Ø 6-16 mm double-acting with magnetic piston cushioning: elastic with integrated ball rail guide
|
|
|
- Oswald Watson
- 10 years ago
- Views:
Transcription
1 Piston rod cylinder uide cylinders ini slide, Series SN 1 Ambient temperature min./max. +0 C / +60 C edium Compressed air ax. particle size 5 µm Oil content of compressed air 0 mg/m³ - 1 mg/m³ Pressure for determining piston forces 6,3 bar aterials: Housing Piston rod Seal all rail table uide rail Aluminum, anodized Stainless steel Polyurethane Aluminum, anodized Steel, hardened a11 Technical Remarks The pressure dew point must be at least 15 C under ambient and medium temperature and may not exceed 3 C. The oil content of compressed air must remain constant during the life cycle. Use only the approved oils from AVENTICS, see chapter Technical information. Piston Ø [mm] Port Working pressure min./max. [bar] 2.5 / 10 1 / 10 1 / 10 Retracting piston force, theoretical [N] Extracting piston force, theoretical [N] Speed max. [m/s] Cushioning energy [Nm] Piston Ø Stroke Weight [kg] Piston Ø Stroke
2 2 Piston rod cylinder uide cylinders ini slide, Series SN aximum additionally moving mass (min. stroke, max. stroke), SN aximum additionally moving mass (min. stroke, max. stroke), SN aximum additionally moving mass (min. stroke, max. stroke), SN
3 Piston rod cylinder uide cylinders ini slide, Series SN 3 max. permissible torque correction factor (a, d) Piston Ø S a [mm] 1) d [mm] 2) x0 3) y0 3) z0 3) x 4) y 4) z 4) S stroke 1) correction factor (a) 2) correction factor (d) 3) Static moment [Nm] 4) Dynamic moment [Nm]
4 4 Piston rod cylinder uide cylinders ini slide, Series SN horizontal vertical Y Y0 D stat. 0 ( F + F ) D dyn. F D F ; Fdyn. X X0 Y; Y0 Z Z0 stat. AO ( F + F ) dyn. A F Fdyn. ; F Z0 Y0 X A Z1; Z0 dyn. stat. A A0 Z0 + 0 Y F m a F m g a 1600 V² F deceleration force [N] F force due to weight [N] m load mass [kg] a deceleration [m/s²] g gravitational acceleration 9.81 [m/s²] V speed [m/s]
5 Piston rod cylinder uide cylinders ini slide, Series SN 5 SN 6/ 10/ 16 L7 L8 L11 D2 L12 D1 T4 E1 2 H4 H3 H5 H7 H5 H6 H6 H4 H2 H8 H1 4 T2 T2 5 E1 L6 L5 1 3 L2 L4 L1 L9 L10 L11 SN-16 3, SN 6/ 10/ 16 Piston Ø D1 D2 E1 * H1 H2 H3 H4 H5 H6 H7 H * Compressed air connection SN
6 6 Piston rod cylinder uide cylinders ini slide, Series SN Piston Ø T4 S stroke SN Piston Ø T4 S stroke SN Piston Ø T4 S stroke
Rotary actuators Rotary wing drives Series RAK. Brochure
Brochure 2 Rotary wing drives, angle of rotation: 30-270 Rotary wing drive, double-acting axis geometry: single 4 Rotary wing drives, angle of rotation: 90-270 Rotary wing drive, double-acting axis geometry:
Valve systems Base plates, according to standard ISO 5599-1. Brochure
ISO 5599-1 Brochure 2 ISO 5599-1 Single subbase Single subbase, thread connections on the side standard: ISO 5599-1 Frame size: ISO 1 - ISO 4 compressed air connection output: G 1/4 - G 1 Reversed pressure
Piston rod cylinder Standard cylinders ISO 15552, series TRB. Brochure
ISO 15552, series TRB Brochure 2 ISO 15552, series TRB Tie rod cylinder Ports: G 1/8 - G 1/2 double-acting with magnetic piston cushioning: pneumatically, adjustable Piston rod: external thread ATEX optional
Piston rod cylinder Tie rod cylinder Series 167. Brochure
Brochure 2 Tie rod cylinder ISO 6431, Ports: G 1/8 - G 1/2 double-acting with magnetic piston cushioning: pneumatically, adjustable Piston rod: external thread 5 Tie rod cylinder ISO 6431, -53 double-acting
Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors
20000 Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 823 Notes 824 Technical
Piston rod cylinders Standard cylinders ISO 15552, series PRA. Brochure
ISO 15552, series PRA Brochure 2 ISO 15552, series PRA Profile cylinder Ports: G 1/8 - G 1/2 double-acting with magnetic piston Cushioning: pneumatically, adjustable Piston rod: external thread ATEX optional
Direct Operated Regulator for 6.0 MPa (Relieving Type) How to Order. Body size 30 40
Direct Operated Regulator for (Relieving Type) Series Service life: 0 million cycles Using NSF-H-certified grease on the guide ring (sliding) part. Improved durability under a high environment with a polyurethane
Profile rail guides LLR
Profile rail guides LLR Content The SKF brand now stands for more than ever before, and means more to you as a valued customer. While SKF maintains its leadership as the hallmark of quality bearings throughout
Unit 24: Applications of Pneumatics and Hydraulics
Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 2 HYDRAULIC AND PNEUMATIC CYLINDERS The material needed for outcome 2 is very extensive
Micro oil-mist lubricator, Series NL2-LBM G 1/4
Version Micro oil-mist lubricator, an be assembled into blocks Mounting orientation vertical Working pressure min./max. 0.5 bar / 6 bar Medium ompressed air Neutral gases Medium temperature min./max. -0
Extruded Body Cylinders, ISO 6431, ISO 15552 compliant Series 62
1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Extruded Body Cylinders, ISO 6431, ISO 15552 compliant Series 62 Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80,
Linear Systems. Main Catalog
Linear Systems Main Catalog MOVITEC Linear Systems The Italian company Impex Tecniche Lineari designs and manufactures a wide range of products under the brand name MOVITEC: Electromechanical and pneumatic
FDH Series Compact Finger Slides
FDH Series Compact Finger Slides Catalog #FDH- Prices effective September 1, 11 Cylinder block- Clear anodized aluminum Top Toolplate and Front Toolbar Clear anodized aluminum Tapped mounting holes ( for
Rexroth Linear Motion Technology
2 Bosch Rexroth Corp. Linear Motion and Assembly Technologies Ball Rail Systems R310A 2202 (2007.05) Rexroth Linear Motion Technology Ball Rail Systems Roller Rail Systems Linear Bushings and Shafts Standard
Oil Dampers with Fixings on. Both Ends. Damping Engineering Oil Dampers with Fixings on Both Ends. Technical Data
amping Engineering Oil ampers with Fixings on Both Ends Oil dampers with fixings on both ends are used when moving objects may not exceed a certain speed e.g. flaps, lids, lever arms. They are fixed at
DryLin ZLW Belt Drive
Belt Drive +50º 0º DryLin toothed belt drives have been developed for the fast positioning of small loads. The linear units with toothed belt drive are corrosion resistant, light and compact, besides having
Linear drives DGC Key features
Linear drives DGC Linear drives DGC Key features General information Compact fitting length relative to stroke Loads and devices can be directly mounted on the slide Three types of cushioning available:
Cylinders Series 40. Double acting, cushioned, magnetic ø160-200 - 250 (DIN/ISO 6431)
Cylinders Series 40 Double acting, cushioned, magnetic ø60-200 - 250 (DIN/ISO 643)»»» DIN/ISO 643 VDMA 24562 Rolled stainless steel rod Adjustable cushioning The cylinders Series 40 with diameters 60,
Vacuum Gate Valve DN 100 and DN 150
Vacuum Gate Valve DN 100 and DN 150 WER Dok.E.02.050_02.051 1. Introduction/Safety Instructions 2. Description 3. Technical Data 4. Installation 5. Operation 6. Maintenance Instructions 7. Spare Parts
Control- and feedback head for integrated mounting on Robolux valves Type 2036
Control- and feedback head for integrated mounting on Robolux valves Type 203 Type 885 Type 88 can be combined with Compact stainless steel design Contactless valve position registration Coloured illuminated
United Kingdom Sweden Germany Switzerland USA, Canada and Mexico China Japan France Linear Units Y07 GB Asia Pacific Italy EU-200502-03 03JUL
Linear Units Linear Units Table of Contents Introduction... 5 Introduction... 5 How to Choose a Unit...6-7 Technical Introduction...8 - Linear Units with Ball Screw Drive and Ball Guide... 3 Introduction...
Solenoid valves 2/2-way direct-operated Type EV210A
Solenoid valves 2/2-way direct-operated Type EV210A Features EV210A NC and NO Very compact valves for industrial application, such as control and dosage For water, oil, compressed air and similar neutral
Normcylinder 1.5002. Technical data. tension-rod cylinder. according DIN ISO 6431 VDMA 24562 DI/DIM DIM DIMB
Normcylinder Universal application through accomodating on DIN ISO 6431 and VDMA 24562 Part 1. Fastening elements according DIN ISO 6431, VDMA 24562 Part 2. Technical data Tension-rod-cylinder according
Cylinders DIN ISO 6431 and VDMA 24 562
Double acting Standard executions Version Shape of barrel Symbol Type MAGNETIC STANDARD AMA AMT 1 For the magnetic reed switches type ASV see from page 1.110.1. For coupling cylinders/reed swiches/brackets
Position Transducers with Restoring Spring 10, 25, 50, 75, 100 mm TR, TRS Series
Position Transducers with Restoring Spring 10, 25, 50, 75, 100 mm TR, TRS Series Special features long life 100 x 10 6 movements outstanding linearity up to ±0.075% choice of plug or cable connection DIN
Hydraulic multidisc Brake H420
S320gb - rev 02/09 S E R V I C E Hydraulic multidisc Brake H420 A N U A L WARNER ELECTRIC EUROPE Rue Champfleur, B.P. 20095, F- 49182 St Barthélemy d Anjou Cedex Tél. +33 (0)2 41 21 24 24, Fax + 33 (0)2
APPLIED PNEUMATICS AND HYDRAULICS H TUTORIAL HYDRAULIC AND PNEUMATIC CYLINDERS. This work covers part of outcome 2 of the standard Edexcel module.
APPLIED PNEUMATICS AND HYDRAULICS H TUTORIAL HYDRAULIC AND PNEUMATIC CYLINDERS This work covers part of outcome 2 of the standard Edexcel module. The material needed for outcome 2 is very extensive so
Kompressoren. Adsorption Dryer AD
Kompressoren Adsorption Dryer AD Adsorption Drying: why? Modern industries require compressed air that is increasingly filtered with low dew point and condensate. Today, the equipment is more sophisticated
Compact cylinder Double acting single rod type. SSD SSD-L (with switch) Double acting Compressed air 1.0. 1.6-10 to 60 (no freezing) Rc1/8 Rc1/4 Rc3/8
* U S 4 Specifications escriptions Bore size mm Actuation Working fluid ax. working pressure Pa in. working pressure Pa Withstanding pressure Pa Ambient temperature Port size Stroke length Rubber cushioned
Adsorption air dryers ADS 1 215
Adsorption air dryers ADS 25 INDUSTRY CUSTOMER SERVICE COMPRESSED AIR AIR INTAKE 20 C 70% UR 760 mm Hg 2 grh 2 O/m 3 AIR PRESSURE 0 bar COOLING SYSTEM 30 C 00% UR 0 bar 2,8 grh 2 O/m 3 A compressor that
Safety for Hydraulics Leak free check valve, pilot operated, series ERV Cartridge type, two stage
Safety for Hydraulics Leak free check valve, pilot operated, series Cartridge type, two stage prevents a load from falling if a burst occurs in feed pipe hardened seat and poppet prevents creep of hydraulically
Highly flexible couplings
Construction and operation 8.03.00 Instructions for installation 8.03.00 Types of stress 8.04.00 Diagrams for static deformation of the coupling ring 8.05.00 Coupling size 8.07.00 Examples of combinations
Radial piston pumps type R and RG
Radial piston pumps type R and RG Operating pressure p max = 700 bar Delivery flow Q max = 91.2 lpm (at 1450 rpm) Geometric displacement V g max = 64.2 cm 3 /rev. 1. General Motor pumps and hydraulic power
STAR Linear Bushings and Shafts Supplement RE 83 117/2001-08. Linear Motion and Assembly Technologies
STAR Linear Bushings and Shafts Supplement RE 83 117/2001-08 Linear Motion and Assembly Technologies STAR Linear Motion Technology Ball Rail Systems Standard Ball Rail Systems Ball Rail Systems with Aluminum
KA/8000/M, KA/8000, ISO cylinder (Stainless steel) Magnetic & Non-magnetic piston, double acting
K/8000/M, K/8000, ISO cylinder (Stainless steel) > > Ø 3... 00 mm > > High corrosion and acid resistance > > Ideal for applications in the food industry > > Conforms to DIN ISO 555, DIN ISO 63, VDM 56
Typical Aluminum GFM Mass Flow Meter
MASS FLOW METERS Design Features n Rigid metallic construction. n Maximum pressure of 1000 psig (70 bars). n Leak integrity 1 x 10-9 of helium. n NIST traceable certification. n Built-in tiltable LCD readout.
Rotary Actuators, NAMUR interface VDI/VDE 3845 & ISO 5211 (ATEX certified) Series ARP
NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8. Rotary Actuators and Grippers Rotary Actuators, NAMUR interface VDI/VDE 384 & ISO 211 (ATEX certified) Series ARP Model: Rack & Pinion - Rotational
T-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5. www.thomsonlinear.com
T-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5 www.thomsonlinear.com Version History Edition Number Edition Date Reason for Revision 1 2004 First edition
Energy transformations
Energy transformations Objectives Describe examples of energy transformations. Demonstrate and apply the law of conservation of energy to a system involving a vertical spring and mass. Design and implement
MINEX -S. Magnetic coupling. You will find continuously updated data in our online catalogue at www.ktr.com
MINEX - 171 Table of contents NEW MINEX - 171 Coupling description 173 Technical description 174 s A 22/4 to B 60/8 with containment shroud made of stainless steel 175 s A 75/10 to F 250/38 with containment
Check Valves Valve locator
Check Valves Valve locator Functional Symbol Flow Typical Model Cavity Rating Pressure Page Check valve, direct L/min (USgpm) bar (psi) FPR/4 Inline () 5 (5) - FPR/8 Inline (8) 5 (5) - FPR/ Inline 45 ()
AIR-AIR PRESSURE MULTIPLIER (BOOSTER)
AIR-AIR PRESSURE MULTIPLIER (BOOSTER) The air-air pressure multiplier, or booster, is an automatic device that compresses air to give an outlet pressure that is double the inlet pressure. It is normally
*Rated to 207 Bar/3000 PSI with Aluminum Body. Denotes New Winner s Circle Product Line. Catalog HY15-3502/US
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type...
United Kingdom Sweden Germany Switzerland USA, Canada and Mexico China Japan France Linear Units Y07 GB Asia Pacific Italy EU-200502-03 03JUL
Linear Units Danaher Motion - Helping you build a better machine, faster Danaher Corporation combined over 30 industry-leading brands such as Kollmorgen, Thomson, Dover, Pacific Scientific, Portescap,
Pneumatic. PXC Limit Switches. Authorised Distributor TTS Valve Technologies Sdn Bhd
Pneumatic PXC Limit Switches Limit Switches Series PXC High durability Very good repeat accuracy Design for process duty cycle Push-in or threaded connection Versatile and easily maintained Wide range
PHYSICS 111 HOMEWORK SOLUTION #10. April 8, 2013
PHYSICS HOMEWORK SOLUTION #0 April 8, 203 0. Find the net torque on the wheel in the figure below about the axle through O, taking a = 6.0 cm and b = 30.0 cm. A torque that s produced by a force can be
Safety for Hydraulics Leak free double check valve, pilot operated, series DERV Cartridge type, two stage
Safety for Hydraulics Leak free double check valve, pilot operated, series Cartridge type, two stage 8 1 1 General description spring closed, pilot operated, cartridge type poppet valve it holds the load
A10VSO Nominal size 18 see RD 92712 A10VSO Nominal size 28...140 see RD 92711
A10VO Nominal size 18 see RD 92712 A10VO Nominal size 28...140 see RD 92711 The variable displacement axial piston pump A10VO in swashplate design was designed for hydrostatic drives in open circuits.
Piston Accumulators. SK Series. Accumulator Catalog. Piston Types. Description. Sealing Systems. End Cap. O-ring. Sealing System. Piston.
SK Series Piston Types TYPE 2 pplication: Low-friction design for higher piston speeds, slow movements without stick-slip effect and high number of actuations (millions). ctual cycles achieved will vary
OUTCOME 1 STATIC FLUID SYSTEMS TUTORIAL 1 - HYDROSTATICS
Unit 41: Fluid Mechanics Unit code: T/601/1445 QCF Level: 4 Credit value: 15 OUTCOME 1 STATIC FLUID SYSTEMS TUTORIAL 1 - HYDROSTATICS 1. Be able to determine the behavioural characteristics and parameters
3/2- and 2/2-way cartridge valve type BVE
3/2- and 2/2-way cartridge valve type BVE for any flow direction, zero leakage, all ports pressure resistant Flow Q max = 70 lpm Perm. pressure p max = 400 bar Additional valves with same function: ' Type
Smooth. Slim. Flexible. EVG Universal Gripper
EVG Smooth. Slim. Flexible. EVG Universal Gripper S ervo-electric 2-finger parallel gripper with highly precise gripping force control and long stroke Field of Application All-purpose, ultra-flexible gripper
Pneumatic actuators The Original! Technics of the top class.
Automatic valves Actuators Accessories Pneumatic actuators The Original! Technics of the top class. Leaflet no. S1-01e-13 Table of contents Advantages and your benefits...page 3 Figure: actuator...page
Flow divider (flow distributor), type TQ
Flow divider (flow distributor), type TQ Pressure p max = 0 bar Flow Q CN max = 00 lpm Share ratio = :. General Task Flow dividers type TQ are self-regulating valves, which largely irrespective of the
Moving Magnet Actuator MI FFA series
Moving Magnet Actuator MI FFA series The moving magnet MI-FFA series actuators are a line of actuators designed to be a true alternative for pneumatic cylinders. The actuators incorporate an ISO 6432 interface
Hydrogen as a fuel for internal combustion engines
Hydrogen as a fuel for internal combustion engines Contents: Introduction External mixture formation for hydrogen operated engines Experimental engine for hydrogen in Stralsund Internal mixture formation
RM/55401/M, Roundline cylinder Magnetic piston, double acting
RM/550/M, Roundline cylinder > > Ø... 00 mm > > Clean line design > > ow friction, long life seals > > Standard magnetic piston for full control system versatility Technical features Medium: Compressed
CYLINDER SERIES ISO 15552 (EX ISO 6431), Ø 32-63 mm TWO-FLAT
YIR SRIS ISO 2 (X ISO 3), - mm TWO-T This version of cylinder is used to keep the parts fixed to the piston rod at an angle and to apply torques within the specified limits. The piston rod of the Two lat
1013 E. The engine for agricultural equipment.
1013 E. The engine for agricultural equipment.... -186 kw at 2300 rpm These are the characteristics of the 1013 E: Modern water-cooled 4- and 6-cylinder in-line engine Turbocharging with charge air cooling
Tool changer. Rugged and durable. For universal use. Payload up to 800 kg
Tool changer TK-Series Rugged and durable For universal use Payload up to 800 kg 02 our own Development Dept. our own Manufacturing Division. Unbeatable in reliability. A product portfolio setting standards
R310EN 2225 (2011.04) The Drive & Control Company
Ball Rail Systems Resist NRII R310EN 5 (011.04) he Drive & Control Company R310EN 5 (011.04) Ball Rail Systems Resist NR II Bosch Rexroth AG 3 Ball Rail Systems Resist NRII General Product Description
Pressure reducing valve, direct operated, Type ZDR 6 D
RE 26 57/2.3 Replaces:.2 Pressure reducing valve, direct operated, ype ZDR 6 D Nominal size 6 Series 4X aximum operating pressure 2 bar aximum flow 5 L/min K 4279/ ype ZDR 6 DP2 4X/ Y Overview of contents
Sensors. Sensors. All Cylinders. Specifications. Features: Features Type REED HALL EFFECT NPN or PNP. Ø8mm - 125mm
Specifications Features Type REED HALL EFFECT NPN or PNP Applicable Series Configurations Construction Materials Body Mounting Bracket Cable Characteristics Operating Temperature Accuracy All Cylinders
IMPORTANT DOCUMENTATION DO NOT DISCARD!
PART NO.: 6441-263C SERIES GRT 3 JAW PARALLEL GRIPPERS INFORMATION SHEET IMPORTANT DOCUMENTATION DO NOT DISCARD! Use this information sheet to assist with gripper installation and setup. File with maintenance
Gear Type Flow Meter VC
Gear Type Flow eter VC Construction and Function 3 5 1 7 Construction 1 Housing Cover 3 Gear reamplifier 5 Connector Sensor 7 Bearing assembly Function The measuring gears are driven by the liquid flow
PUMP AND MOTOR DIVISION
INSTALLATION MANUAL SERIES P2 and P3 MOBILE PISTON PUMP 1 Check model code / compare with your paper work Nameplate of the pump Ordering / Sales Acknowledgement 2 Check rotation of the pump Clockwise rotation
Electrical connection technologies Electrical connectors Electrical connectors with cable, series. Brochure
Electrical connection technologies Electrical connectors Electrical connectors with cable, series CN Brochure Electrical connection technologies Electrical connectors Electrical connectors with cable,
Custom configuration such as modified angle dimensions, other flange standards, 3-way function, alternative materials.are available on request.
LEAKVALVE: HIGHLIGHTS The core of this valve is a diaphragm in stainless steel 316L, gold plated. Robust, it cannot be damaged with any normal methods. The dead volume is kept as small as possible. There
Pressure Relief Valves SPV, SPVF
Pressure Relief Valves SPV, SPVF Construction of the Pressure Relief Valves SPV, SPVF Symbol Description The direct spring, sliding piston Pressure Relief Valve SPV/SPVF is intended for inline mounting
Pneumatic Grippers Parallel and Angular Grippers. Catalog 1900-2/US
Pneumatic Grippers Parallel and Angular Grippers Catalog 19-2/US Catalog 19-2/US OContents GPR Series Rotary vane driven design GPR GPCR Series P5G-HPM(C) Series P5G-HP Series GPT Series P5G-AP Series
E4E PILOT OPERATED DIRECTIONAL CONTROL VALVE WITH ELECTRIC PROPORTIONAL CONTROL SERIES 51
83 300/100 ED E4E PILOT OPERATED DIRECTIONAL CONTROL VALVE WITH ELECTRIC PROPORTIONAL CONTROL SUBPLATE MOUNTING CETOP P05 p max 250 bar Q max (see specification table) MOUNTING INTERFACE OPERATING PRINCIPLE
Free piston Stirling engine for rural development
Free piston Stirling engine for rural development R. Krasensky, Intern, Stirling development, [email protected] W. Rijssenbeek, Managing director, [email protected] Abstract: This paper presents
ECO 80 PRODUCT DESCRIPTION FEATURES. Power output S1 100% Adjustable air nozzle. Liquid cooling. Minimalmengenschmierung MMS retrofit
A PRODUCT DESCRIPTION Power output S6 40% Power output S1 100% Rotation speed Diameter Spindlehousing Spindle interface 3.0 kw 2.5 kw to 40.000 rpm 80 mm Stainless steel HSK - E25 FEATURES Adjustable air
Combi switchbox with integrated 3/2 way pilot valve
H Combi switchbox with integrated 3/2 way pilot valve Construction The GEMÜ combi switchbox with integrated 3/2 way pilot valve for pneumatically operated quarter turn actuators has a micro-processor controlled
Manual piston sampler...m 11
SAMPLING Manual piston sampler...m 11 Screw sampler...prec 22...PREC 100 Slide sampler...pr 55 Rotative screw sampler...prv Piston sampler...p 11 Sampler on belt conveyor...pba Rotating cup sampler...pgr
LECTURE 28 to 29 ACCUMULATORS FREQUENTLY ASKED QUESTIONS
LECTURE 28 to 29 ACCUMULATORS FREQUENTLY ASKED QUESTIONS 1. Define an accumulator and explain its function A hydraulic accumulator is a device that stores the potential energy of an incompressible fluid
Products. Air Bearing- Linear systems 06-2009 EITZENBERGER. Luftlagertechnik GmbH. Feichtmayrstraße 17 D-82405 Wessobrunn
Products Air Bearing- Linear systems 06-2009 ITZNBRGR D- mail: URL. Index - Air Bearing linear Systems Z 0526 Air Bearing Linear Stage with high resolution encoder and iron free linear motor Z 0512 XY-Air
Vectra Caravan 1.8 90kW/122hp 5-speed station wagon 5 doors 1
Vectra Caravan 1.8 90kW/122hp 5-speed station wagon 5 doors 1 1.8 ECOTEC front, transverse in front of axle, 7 50' forward inclined Bore (mm): 80.5 Stroke (mm): 88.2 Displacement (cc): 1796 Compression
Assisted lift operated 2/2-way solenoid valves Type EV250B
MAKING MODERN LIVING POSSIBLE Data sheet Assisted lift operated 2/2-way solenoid valves Type EV250B EV250B with assisted lift can operate from zero and up to 10 bar differential pressure. This 2/2-way
*Rated to 207 Bar/3000 PSI with Aluminum Body. Catalog HY15-3501/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO.
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. /GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type... 5/132...
3/2-way Solenoid Valve, direct-acting, NC or NO
3/2-way Solenoid Valve, direct-acting, NC or NO Electrical connection cable plug, Form A With or without manual override as standard Threaded port and sub-base s Impulse optional Type 6014 can be combined
Rodless Pneumatic Cylinders Series OSP-P
Rodless Pneumatic Cylinders Series OSP-P Contents Description Data Sheet No. Page Standard Cylinders Overview P-1.10.001E 9-13 Technical Data P-1.10.002E-1 to 3 15-17 Dimensions P-1.10.002E-4 to 9 18-23
2/2 and 3/2 Way Size 6 Seat Valves
2/2 and 3/2 Way Size 6 Seat Valves Directly operated Interface and subplate dimensions according to DIN 24340 and ISO Line connection port size G 3/8" Cartridge design PN [p max. ] = 315 bar 7501856.06.12.08
Standard Cables (Without electromagnetic brake, with electromagnetic brake) CC010ES-2. 1 m CC020ES-2. 2 m CC030ES-2. 3 m CC050ES-2.
Motorized Actuators Motor Cables EZS /EZS for Clean Room Use This cable is a dedicated cable for connecting the linear slide of the EZS Series and EZS Series for Clean Room Use with the controller. Use
Ball Rail Tables TKK. with Ball Rail Systems and Ball Screw Drive R310EN 2501 (2008.04) The Drive & Control Company
with Ball Rail Systems and Ball Screw Drive R310EN 2501 (2008.04) The Drive & Control Company Bosch Rexroth AG Linear Motion and Assembly Technologies Ball Rail Systems Roller Rail Systems Linear Bushings
Installation Detailed installation instructions are provided which should be strictly followed.
Specification System 6 The Metal Technology Thermally-Broken Vertical Slide Window has been designed in such a way that its'attractive and clean lines will enhance all types of residential and commercial
P = n M 9550 [kw] Variable Intake Manifold in VR Engines. Self-study programme 212. Principles and Description of Operation. Service.
![P = n M 9550 [kw] Variable Intake Manifold in VR Engines. Self-study programme 212. Principles and Description of Operation. Service.](/thumbs/40/21744251.jpg "P = n M 9550 [kw] Variable Intake Manifold in VR Engines. Self-study programme 212. Principles and Description of Operation. Service.")
Service. Self-study programme 212 Variable Intake Manifold in VR Engines Principles and Description of Operation P = n M 9550 [kw] M [Nm] P [kw] n [min -1 ] 212_020 The output and torque of an engine have
Valve series MN-06 acc. to NAMUR, 3/2-way G1/4 750 Nl/min (0.762 Cv)
Valve series MN-06 acc. to NAMUR, 3/2-way G1/4 750 Nl/min (0.762 Cv) Order code Series and function 1) Plug socket see page 5.042. MN-06-310-HN-442 Standard coil 1) 441 = 12 V DC, 4.2 W 442 = 24 V DC,
Corsa 1.0 44kW/60hp 5-speed hatchback 3 doors 1
Corsa 1.0 44kW/60hp 5-speed hatchback 3 doors 1 1.0 TWINPORT ECOTEC Cylinders, number: 3 Stroke (mm): 78.6 Displacement (cc): 998 in line; 4 main bearings multi point fuel injection, Motronic 3-way cat.
Overview of types. Technical data
Technical data sheet R3..xx-S.. Characterised control valves, 3-way, with internal thread For closed cold and warm water systems For modulating water-side control of HU and heating systems ir bubble-tight
CILINDRI SENZA STELO RODLESS CYLINDERS
Il cilindro senza stelo nasce dall esigenza di ridurre gli ingombri a parità di corsa E' fornito in diverse versioni e gli alesaggi variano da 25 a 63. I pregi principali di questo cilindro sono l'eccezionale
kymanual or Automatic - it s your Choice
. kymanual or Automatic - it s your Choice ky LKB Automatic or Manual Butterfly Valve Application LKB is a sanitary automatically or manually operated butterfly valve for use in stainless steel pipe systems.
LINEAR MOTION CONTROL
LINEAR MOTION CONTROL Technical Data Sheet Static Locks RLSS Series Nexen s new generation of linear holding/locking devices take rod locking technology to the next level. With superior performance, these
TBG-25 OPTIONS X AXIS TRAVEL (MM) Z AXIS TRAVEL (MM) OPTIONS FOR: SPECIFICATIONS. Specifications. Configuration. Belt Type 25.
LINEAR ROBOTICS > T-BOT GANTRY ROBOTS T-BOT GANTRY ROBOTS TBG-25 OPTIONS X AXIS TRAVEL (MM) 500 1000 2000 Custom Z AXIS TRAVEL (MM) 250 500 Custom Controls Motor Gearbox HOW TO BUILD YOUR TBG-25: Features
SITEMA PowerStroke. Technical Information TI-P11. 1 Function. 2 Applications. Mould Closing Devices series FSK. Contents
English translation of German original Technical Information TI-P11 SITEMA PowerStroke Mould Closing Devices series FS drive system for powerful forces on a short stroke hydraulic actuation closing force
Hydraulic cylinders Tie rod design. Type CD70 / CG70. Contents. Features. RE 17016 Edition: 2014-03 Replaces: 08.08
Hydraulic cylinders Tie rod design Type CD / CG RE 1 Edition: 2014-03 Replaces: 08.08 Series Component series 1X Nominal pressure bar [7 MPa] Features Contents types of mounting Piston Ø (ØAL)... mm Piston
Steering unit. Table of contents. Features RE 11872/05.06. Type LAGL. Frame sizes 500 to 1000 Component series 1X Maximum flow 80 l/min
Steering unit RE 11872/05.06 /10 Type LAGL Frame sizes 500 to 1000 Component series 1X Maximum flow 80 l/min H7375 Table of contents Contents Page Features 1 Ordering code 2 Function, section 3 Device
Servo Motor Selection Flow Chart
Servo otor Selection Flow Chart START Selection Has the machine Been Selected? YES NO Explanation References etermine the size, mass, coefficient of friction, and external forces of all the moving part