Enhanced SEADS (Serial Enabled Auto-Dialer Solution) Integration

Transcription

1 Page 1 of 6 Enhanced SEADS (Serial Enabled Auto-Dialer Solution) Integration Overview This document outlines how to program and interface a SEADS Auto-Dialer to Access It! Universal. Required Components The following components are required to complete the integration. Access It! Universal Software EP-1502 or EP-2500 (Firmware 1.107) SEADS Kit consisting of: (1) 95M Keltron Dialer (1) NCL - Enclosure (1) SAP - Keltron Dialer Adapter Plate (1) VB-1T 12-24VDC Power Booster Hardware / Wiring References SEADS Auto-Dialer to PC Keltron-Dialer RS-232 Port PC Com Port Comments DB-9 Male DB-9 Female Straight Through DB-9 Male to DB-9 Female RS-232 Cable Table 1 EP-2500 / EP-1502 Keltron-Dialer EP-1502 / EP-2500 SEADS Auto-Dialer DB9 Connector TXD (Black) PIN 3 RXD (Red) PIN 2 GND (Green) PIN 5 Table 2 Configuring the SEADS Auto-Dialer 1. Connect the SEADS Auto-Dialer to the PC. NOTE: See table Insert the Keltron S/FDACT Programmer CD-ROM into the PC. 3. Click the OK button at the S/FDACT Programmer Setup welcome window. 4. Select the installation directory accordingly. 5. Click the Install button located in the upper left corner of the window. 6. Select a Programmer Group. 7. Click the Continue button. 8. Click the OK button at the S/FDACT Programmer Setup was completed successfully window. 9. Click Start Programs S/FDACT Programmer. 10. Click Set Comm Port from the file menu. 11. Select the COM port that the SEADS Auto-Dialer is connected to. 12. On the SEADS Auto-Dialer, press the Program soft key. NOTE: In programming mode, the red and yellow serial port LEDs will flash once a second. To exit the programming mode, disconnect the DB-9 cable and wait 60 seconds or press the Test soft key. S/FDACT Programmer Set Event Codes Use Default Event Codes Uncheck the Use Default Event Codes when custom event codes are needed. Set Telephone Numbers Primary Phone Number Sets the primary phone number the SEADS Auto-Dialer will call. NOTE: This number is generally provided by the central station and may be up to 20 digits long. 400 Fisher Street, Suite G Munster, IN

2 Page 2 of 6 Secondary Phone Number Sets the secondary phone number the SEADS Auto-Dialer will call. NOTE: This number is generally provided by the central station and may be up to 20 digits long. Set Account Numbers Primary Account Number Sets the primary account number the SEADS Auto-Dialer will use. NOTE: This number is generally provided by the central station and may be up to 6 digits long. Secondary Account Number Sets the secondary account number the SEADS Auto-Dialer will use. NOTE: This number is generally provided by the central station and may be up to 6 digits long. Set Options Telephone Lines Used Select the Line 1 Only option if a second phone line is not available. NOTE: Selecting this option prevents the S/FDACT from reporting a line fault condition on line 2. Send Troubles to Second Account Check the 2nd Account checkbox if troubles are to be sent to the secondary account only. NOTE: Normally the SEADS Auto-Dialer will report all troubles to the primary account and only use the secondary account and telephone number if it is unable to report to the primary account. Set Daily Test Interval Select how often the daily test reports will occur. NOTE: The default setting is once every 24 hours. Set Daily Test Time Enter the time for which the daily test reports will be sent. NOTE: The time is in entered in 24 hour format from 00:00 (midnight) to 23:59. The factory default is 00:00. Set Date and Time Auto Sync Time Mode Selecting this mode will automatically sync the SEADS Auto-Dialer date and time to that of the clock within the PC. NOTE: This is the default mode. Change Time Mode Selecting this mode enables the Set Date and Set Time fields so that a specific date and time may be manually sent to the SEADS Auto-Dialer. NOTE: See the Set Date, Set Time and Upload Date/Time to S/FDACT sub-categories. Set Date Manually sets the SEADS Auto-Dialer to a specified date. NOTE: This field is disabled when set to Auto Sync Time Mode. Set Time Manually sets the SEADS Auto-Dialer to a specified time. NOTE: This field is disabled when set to Auto Sync Time Mode. Download Date/Time from S/FDACT This utility will request the current date and time values from within the real-time clock and calendar of the SEADS Auto-Dialer. Upload Date/Time to S/FDACT This utility will set the current date and time values within the real-time clock and calendar of the SEADS Auto-Dialer to the values entered within the Set Date and Set Time fields. Upload / Download Download Config from S/FDACT This utility will read the configuration program from the SEADS Auto-Dialer and display the current settings. Upload Config to S/FDACT This utility will program the SEADS Auto-Dialer with the currently displayed settings.

3 Page 3 of 6 EP-2500 / EP-1502 Configuration 1. Install and configure the EP-2500 / EP-1502 to communicate with Access It! Universal. NOTE: The EP board must be at firmware or higher 2. Wire the Keltron-Dialer to the EP-2500/ EP-1502 s RS-232 port. NOTE: See table Browse to the EP-2500/EP-1502 s internal web browser. 4. Log into the web browser NOTE: Default username is admin and password is password. 5. Select Central Station from the left hand menu. 6. Set Connection Type to Serial-RS Set Baud Rate to Set Data Security to None 9. Set Flow Control to None 10. Click the Accept button 11. Click Apply Settings from the left hand menu 12. Click the Apply Settings, Reboot button NOTE: The SCP will reset. 13. Close the web browser Access It! Universal Configuration 1. From the file menu, select Go Main Hardware 2. Select SCP s 3. Edit the EP-2500/EP Select the Intrusion Processing tab 5. Set Intrusion Processing Mode to an Enhanced Intrusion Processing mode 6. Enter a custom Command Code 7. Click Save NOTE: The SCP will reset. 8. Expand the EP-2500/EP-1502 from the left hand tree 9. Select Alarm Zones 10. Edit Alarm Zone Number 01 NOTE: Alarm Zone 00 cannot be used with the SEADS integration. 11. Select the Central Station Reporting tab 12. Check Enable Central Station Reporting 13. Enter the Account ID 14. NOTE: See the S/FDACT Programmer section 15. Enter the Alternate Account ID 16. NOTE: See the S/FDACT Programmer section 17. Enter Group Number NOTE: See the S/FDACT Programmer section 18. Enter the Comm Timeout 19. Select the Points tab 20. Click Add Point 21. Select the Point Type 22. Select which Point to add 23. Select a Point Mode 24. Select a Monitoring Mode 25. Select an Entry Delay value 26. Select the Central Station Reporting tab 27. Enter the SIA Zone number for this Point 28. Select the SIA Point Type for this Point 29. Click OK 30. Repeat steps for any additional Points 31. Click Save Application Notes The daily test performed by the SEADS Auto-Dialer will only test the connection between the SEADS Auto-Dialer and the central station. NOTE: There is no way to test or monitor the integrity of the connection between the access control hardware and the SEADS Auto-Dialer!

4 Page 4 of 6 Typical Layout SEADS Field Wiring Diagram

5 Page 5 of 6 SIA Standard Events Codes AN Analog Sensor - R AR AC Power Restoral AS Analog Sensor BA Burglary Alarm BB Burg Zone Bypass BC Burglary Cancel BD Swinger Trouble BE Swinger Trouble - R BH Burg Alarm Restoral BJ Burg Trouble Restorl BM Cross Point Verified BR Burg alrm/tbl Restrl BS Burglary Supervision BT Burglary Trouble BU Burglary Unbypass BV Burglary Verified BX Burglary Test BZ Non-Fire Device Miss CA Automatic Closing CD Fail to Close CE Closing Extended CF Closing Forced CG Close Area (partial) CI Fail to Close CJ Late Closing CK Early Closing CL Closing CM Pt Miss Close CP Automatic Closing CR Recent Close CS Close Keyswitch CT Late to Open CW Force Armed CZ Point Closing DB Zone Equals Air Flow DC Access Closed DD Access Denied DE Request to Enter DF Door Forced DG Access Granted DH Door Forced Restoral DI Zone Equals Humidity DJ Door Forced Trouble DK Access Lockout DL Audible Door Open DM Zone = Fluid Level DN Silent Door Open DO Access Open DP Access Deny Bad Time DQ Disarm Access Denied DR Door DS Door Station DT Access Trouble DU Dealer ID DV Access Denied DW Access Denied EA EE ER ET EX EZ FA FB FC FH FI FJ FK FM FR FU FX GH GJ GR GS GU GX HA HB HH HJ HR HS HT HU IA IR JA JD JH JK JL JO JP JR JS JT JV JX JY JZ KA KB KH KJ KR KU LB LD LE Exit Alarm Exit Error Expansion Restoral Expansion Trouble External Devic State Missing Exit Error Fire Alarm Fire Bypass Fire Cancel Fire Alarm Restoral Fire Test Begin Fire Trouble Restorl Fire Test End Fire Alarm Cross Pt Fire Alrm/Tbl Rstrl Fire Unbypass Fire Test Gas Alarm Restoral Gas Trouble Restoral Gas Alrm/Tbl Restorl Gas Supervisory Gas Unbypass Gas Alarm Test Hold-up Alarm Silent Hold-up Bypass Hold-up Alarm Restrl Hold-up Troubl Rstrl Hold-up Alm/Tbl Rstr Hold-up Supervisory Hold-up Trouble Hold-up Unbypass Equipment Failure Equipment Failure-R Tamper User Code Date Changed Holiday Changed Latchkey Alert Log Threshold Log Overflow User on Premises Schedule Executed Schedule Changed Time Changed User Code Changed User Code Deleted User Code Added User Level Set Heat Alarm Heat Bypass Heat Alarm Restoral Heat Trouble Restorl Heat Alm/Tbl Restorl Heat Unbypass Begin Local Program Program Access Deny Listen In Ended LF LR LS LU LX MA MB MH MJ MR MS MT MU NA NC NL NR NS NT OA OG OH OI OJ OK OL OP OR OS OT OZ PA PB PH PJ PR PS PT PU QA QB QH QJ QR QS QT QU RA RB RC RD RN RO RP RR RS Listen In Begin Phone Line Restoral Local Program Succes Local Program Failur Local Program Ended Medical Alarm Medical Bypass Medical Alarm Rstrl Medical Trouble Medical Alm/Tbl Rstl Medical Supervisory Medical Trouble Medical Unbypass No Activity Time Trouble Comm Network Perimeter Armed Comm Network Restorl No Activity Time Rst Trouble Comm Network Automatic Opening Opening (by Area) Early Opening Fail to Open Late Opening Early Open After Alm Late Open After Alm Opening Disarm for Alarm Open Keyswitch Late to Close Opening by Zone Panic Panic Bypass Panic Alarm Restoral Panic Trouble Rstorl Panic Alm/Tbl Rstorl Panic Supervisory Panic Trouble Panic Unbypass Emergency Alarm Emergency Bypass Emergency Alarm Rstl Emergncy Troubl Rstl Emrgncy Alm/Tbl Rstl Emergency Supervsry Emergency Trouble Emergency Unbypass Remote Prog Cal Fail Remote Prog Begin Relay Close Remote ProgAcessDeny Remote Reset Relay Open Automatic Test Power UP Remote Prog Success

6 Page 6 of 6 RT RU RX RY SA SB SH SJ SR SU TA TB TC TE TH TJ TP TR TS TT TU TX UA UB UC UH UJ UR US UT Data Lost Remote Program Fail Manual Test Off Normal Sprinkler Alarm Sprinkler Bypass Sprinkler Alarm Rstl Sprinkler Trbl Rstl Sprnklr Alm/Tbl Rstl Sprnklr Unbypass Tamper Alarm Tamper Bypass All Points Tested Test End Tamper Alarm Rstl Tamper Trouble Rstl Walk Test Point Tamper Restoral Test Begin Tamper Trouble Tamper Unbypass Test Report Untyped Zone Alarm Untyped Zone Bypass Cancel Burg Alarm Untyped Alarm Rstl Untyped Trouble Rstl Untyped Alm/Tbl Rstl Untyped Supervisory Untyped Trouble UU UV UW UX UY UZ VI VO VR VT VX VY VZ WA WB WH WJ WR WU XA XE XF XH XI XJ XL XM XQ XR XS Untyped Unbypass Cancel Burg Alarm Invalid Signal Test Untyped Missing Tbl Untyped Missing Alm Printer Paper In Printer Paper Out Printer Restoral Printer Trouble Printer Test Printer On-Line Printer Off-Line Water Alarm Water Bypass Water Alarm Rstl Water Trouble Rstl Water Alm/Tbl Rstl Water Unbypass Extra Account Report Extra Point Trouble Extra RF Point RF Interference Rstl Sensor Reset RF Receiver Rstl Low RF Signal Streng Miss CrossPoint Alm RF Interference XMTR Battery Rstl RF Receiver XT XW XX YC YD YE YF YG YH YI YJ YK YM YN YO YQ YR YS YW YX YY YZ ZH ZJ ZR ZS ZT ZU XMTR Battery Trouble Forced Point Fail Test Comm Failed Trouble Rcvr Line Card Fail Rcvr Line Card Rstl Checksum Fail Parmtr Parameter Changed Bell/Siren Restoral Over Current Trouble Over Current Restorl Communications Rstl System Battery Miss Bad Transmission Unknown Message Power Supply Restorl System Battery Rstl Communications Tbl Watchdog Timer Reset Service Required Status Report Service Completed Freezer Alarm Restrl Freezer Troubl Rstrl Freezer Alm/Tbl Rstl Freezer Supervisory Freezer Trouble Freezer Unbypass