Korenix Industrial Product Selection Guide - Industrial Power Supply

Transcription

1 Universal AC input/full range Fix switching frequency at 100KHz DR A 0 ~ 2A 48W RIPPLE & NOISE (max.) Note.2 480mVp-p OUTPUT VOLTAGE ADJ. RANGE 21.6 ~ 26.4V 800ms, 60ms/230VAC at full load HOLD UP TIME (Typ.) 100ms/230VAC at full load 85 ~ 264VAC 120 ~ 370VDC 80% 1.5A/115VAC 0.75A/230VAC INRUSH CURRENT (Typ.) COLD START 28A/115VAC 56A/230VAC LEAKAGE CURRENT <1mA / 240VAC 27.6 ~ 32.4V Protection type : Shut off o/p voltage, clamping by zener diode ENVIRONMENT STORAGE TEMP., HUMIDITY Tj 135 typically (U1) detect on heat sink of power transistor -10 ~ +50 (Refer to output load derating curve) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes; Mounting: Compliance to IEC SAFETY STANDARDS UL508, TUV EN approved 364.6K hrs min. MIL-HDBK-217F (25 ) 93*78*67mm (L*W*H) 0.31Kg; 48pcs/16.1Kg/1.3CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient.

2 Universal AC input / Full range Protections:Short circuit / Overload / Over voltage / Over Fix switching frequency at 50KHz DR A 0 ~ 3.2A 76.8W RIPPLE & NOISE (max.) Note.2 150mVp-p 48 ~ 53V 1000ms, 60ms/230VAC 1800ms, 60ms/115VAC at full load HOLD UP TIME (Typ.) 60ms/230VAC 12ms/115VAC at full load 85 ~ 264VAC 120 ~ 370VDC 80% 81% 1.6A/115V 0.96A/230V INRUSH CURRENT (Typ.) COLD START 20A/115VAC 40A/230VAC LEAKAGE CURRENT <1mA / 240VAC 29 ~ 34V 58 ~ 65V 85 ~ 5 (TSW1) detect on heat sink of power transistor Protection type : Shut down o/p voltage, recovers automatically after goes down ENVIRONMENT STORAGE TEMP., HUMIDITY DR V 1.6A 0 ~ 1.6A 76.8W 240mVp-p -10 ~ +60 (Refer to output load derating curve) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes; Mounting: Compliance to IEC SAFETY STANDARDS UL508, TUV EN approved 123.1K hrs min. MIL-HDBK-217F (25 ) 55.5*125.2*100mm (W*H*D) 0.6Kg; 20pcs/13Kg/1.29CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient.

3 AC input range selectable by switch Fixed switching frequency at 55KHz DR A 0 ~ 5A 120W RIPPLE & NOISE (max.) Note.2 80mVp-p 500ms, 70ms/230VAC 500ms, 70ms/115VAC at full load HOLD UP TIME (Typ.) 36ms/230VAC 32ms/115VAC at full load 88 ~ 132VAC/176 ~ 264VAC by switch 248 ~ 370VDC 84% 2.6A/115VAC 1.6A/230VAC INRUSH CURRENT (Typ.) COLD START 20A/115VAC 40A/230VAC LEAKAGE CURRENT <3.5mA / 240VAC 29 ~ 33V 90 5 (TSW1) Protection type : Shut down o/p voltage, recovers automatically after goes down -10 ~ +60 (Refer to output load derating curve) ENVIRONMENT STORAGE TEMP., HUMIDITY 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC SAFETY STANDARDS UL508, UL , TUV EN approved 136.8Khrs min. MIL-HDBK-217F (25 ) 65.5*125.2*100mm (W*H*D) 0.79Kg; 20pcs/16.5Kg/1.29CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient.

4 Universal AC input / Full range Built in active PFC function Fixed switching frequency at 100KHz DRP A 0 ~ 10A 240W RIPPLE & NOISE (max.) Note.2 80mVp-p OUTPUT VOLTAGE ADJ. RANGE 24 ~ 28V 800ms, 40ms/230VAC 800ms, 40ms/115VAC at full load HOLD UP TIME (Typ.) 24ms/230VAC Note.5 85 ~ 264VAC 24 ms/115vac at full load 120 ~ 370VDC POWER FACTOR (Typ.) 0.96/230VAC 0.99/115VAC at full load 84% 2.8A/115VAC 1.4A/230VAC INRUSH CURRENT (Typ.) LEAKAGE CURRENT COLD START 27A/115VAC <3.5mA / 240VAC 45A/230VAC ENVIRONMENT STORAGE TEMP., HUMIDITY 30 ~ 36V (TSW1)detect on heat sink of power transistor Protection type : Shut down o/p voltage, recovers automatically after goes down -10 ~ +70 (Refer to output load derating curve) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC SAFETY STANDARDS UL508, UL , TUV EN approved 105.5Khrs min. MIL-HDBK-217F (25 ) 125.5*125.2*100mm (W*H*D) 1.2Kg; 12pcs/15.5Kg/1.29CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient. 5. Derating may be needed under low input voltages. Please check the derating curve for more details.

5 AC input range selectable by switch Built-in passive PFC function compliance to EN High efficiency 89% and low dissipation Built-in constant current limiting circuit EN (EN ) industrial immunity level DRP-480S-24 20A 0 ~ 20A 480W RIPPLE & NOISE (max.) Note.2 120mVp-p 1.0% HOLD UP TIME (Typ.) FREQUENCY RANGE 0.5% 1.0% 1200ms, 40ms/230VAC, 115VAC at full load 23ms/230VAC, 115VAC at full load 90 ~ 132VAC/180 ~ 264VAC by switch 47 ~ 63Hz 254 ~ 370VDC POWER FACTOR (Typ.) 0.7/230VAC only 89% 8A/115VAC 3.2A/230VAC INRUSH CURRENT (Typ.) LEAKAGE CURRENT COLD START 27A/115VAC <3.5mA / 240VAC 45A/230VAC ENVIRONMENT STORAGE TEMP., HUMIDITY 30 ~ 36V (TSW : Detect on heatsink of power switch) Protection type : Shut down o/p voltage, recovers automatically after goes down -20 ~ +70 (Refer to output load derating curve) -40 ~ +85, 10 ~ 95% RH Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC SAFETY STANDARDS UL508, UL , TUV EN Approved EMI CONDUCTION & RADIATION Compliance to EN55011 (CISPR11), EN55022 (CISPR22), EN Class B Compliance to EN ,3,4,5,6,8,11, ENV50204, EN , EN (EN ) Heavy industry level, criteria A 187.9Khrs min. MIL-HDBK-217F (25 ) 227*125.2*100mm (W*H*D) 2.6Kg; 6pcs / 16.6Kg / 1.75CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient.