Attachments for Projects 60 85ft.

Transcription

1 Document Scope James Hardie Siding Products are noncombustible fiber-cement siding, manufactured by James Hardie Building Products Inc. Siding Product Dimensions Lap Siding Thickness 5/16 inch Length 12 feet Width Available in 5 ¼, 6 ¼, 7 ¼, 7 ½, 8 ¼, or 9 ¼ inches Panel Siding Thickness 5/16 inch Length 8, 9 & 10 feet Width 4 feet Shingle Panel Siding Thickness 1/4 inch Length 48 inches Width 15 ¼ inches Siding Product Composition James Hardie siding products are a Grade II, Type A, fiber-cement flat sheet as defined by ASTM C The siding is manufactured by the Hatschek process and cured by high pressure steam autoclaving. Siding Code Compliance This document applies to HardiePlank Lap Siding, CemPlank lap siding, Prevail lap siding, HardiePanel Vertical Siding, CemPanel Siding, Prevail Panel and HardieShingle Panel Siding. The attachment details listed in this document are limited to buildings not exceeding 85 feet in mean roof height. Siding General Description James Hardie Siding Products comply with: The 2009, 2012, and 2015 International Building Code (IBC) Section , 2018, and 2021 International Building Code (IBC) Section and 2009, 2012, 2015, 2018 and 2021 International Residential Code (IRC) Table R703.3(1) and Section R as ASTM C 1186 Grade II, Type A Fiber Cement. Wind Design: Design Tables 2, 3 and 4 as shown in this report provide the allowable capacity in mph for transverse load conditions for HardiePlank lap siding, HardiePanel Vertical Siding and HardieShingle Panel Siding respectively attached to wood framing, metal framing and 7/16 inch Wood Structural Panel (tested to ASTM E 330). Fire Characteristics: James Hardie Siding Products are classified as noncombustible when tested in accordance with ASTM E136. James Hardie Siding Products may be used in ASTM E119 fire resistance rated assemblies as listed by Warnock Hersey 60 minute design JH/FCS 60-01, JH/FCS 60-02, JH/FCS 60-03, and JH/FCS James Hardie Siding Products are Class A material according to 2006, 2009, 2012, and 2015 IBC Section and 2018, 2021 IBC Section Surface burning characteristics in accordance with ASTM E 8 4: Flame Spread Index = 0 and Smoke Developed Index 5. The building official reserves the right to approve alternate materials, design and methods of construction based on research reports and/or tests based on 2006, 2009, 2012, 2015, 2018, and 2021 IBC Section , 2006, 2009, 2012, 2015, 2018, and 2021 IRC Section R Test reports can be furnished to the building official upon request, contact your local James Hardie sales representative. For more information, contact James Hardie at J-HARDIE ( ) or info@jameshardie.com). Siding Installation Requirements James Hardie Siding Products shall be installed on exterior walls braced in accordance with the applicable building code. A water-resistive barrier complying with Section of the IBC or Section R703.2 of the IRC is required to be installed. Install siding in accordance with this report and the James Hardie s published installation requirements. For a copy contact your local James Hardie sales representative or visit Table 1, James Hardie Siding Products ASTM C 1186 Physical Properties and Supplementary Requirements Page 1 of 10

2 FASTENER TYPE 3,10 1/4 1/4 1/4 2X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood Page 2 of 10

3 FASTENER TYPE 3,10 1/4 1/4 1/4 8d siding nail, 0.92 in x in 8d siding nail, 0.92 in x in 2X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood X4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood Page 3 of 10

4 FASTENER TYPE 3, d siding nail, 0.92 in x in 8d siding nail, 0.92 in x in 8d ring shank box nail, 0.113" shank X 0.260" X 2.375" L 8d ring shank box nail, 0.113" shank X 0.260" X 2.375" L 0.092" shank X 0.222" X 2.5" long galv. nail 2 x 4 wood x 4 wood x 4 wood x 4 wood x 4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood /4 6d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood /4 6d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood Page 4 of 10

5 FASTENER TYPE 3,10 8d common 2X4 wood d common 2X4 wood /4 8d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood d common 2X4 wood /4 8d common 2X4 wood d common 2X4 wood d common 2X4 wood /4 7 1/4 or 7 at 12 at 12 at 12 at 12 at 12 at 8 at 6 ET&F pin x 1.5" x 0.313" Page 5 of 10

6 FASTENER TYPE 3,10 1/4 7 1/4 or 7 7 1/4 or 7 1/4 9 1/4 or 9 7 1/4 or 7 1/4 9 1/4 or 9 7 1/4 or 7 1/4 9 1/4 or 9 12 ET&F pin x 1.5" x 0.313" ET&F pin x 1.5" x 0.313" ET&F pin x 1.5" x 0.313" ET&F pin x 1.5" x 0.313" ribbed waferhead screw ribbed waferhead screw ribbed waferhead screw ribbed waferhead screw ribbed waferhead screw ribbed waferhead screw ribbed waferhead screw ribbed waferhead screw ribbed waferhead screw ribbed waferhead screw ribbed waferhead screw Page 6 of 10

7 FASTENER TYPE 3,10 7 1/4 or 7 1/4 9 1/4 or Values are for species of wood having a specific gravity of 0.42 or greater, unless otherwise noted. 2 Face = Fastened through the overlapping plank. Blind = Fastened through the top edge of single plank. 3 ET&F pin fasteners have knurled shanks. 4 Fastener length shall be sufficient to penetrate back side of the minimum sheathing by at least ¼ for nails or 3 full threads for screws. 5 Values are for species of wood having a specific gravity of 0.50 or greater. 6 Values are for species of wood having a specific gravity of 0.40 or greater. 7 Metal studs must be minimum Fy = 33 ksi and 2012 IBC Section , Eqn , Vasd=Vult IBC Section , Eqn and 2018 IBC Section , Eqn , Vasd = Smooth shank nails are outside of the scope of this report Page 7 of 10

8 Table 3, Wind Design Table for HardiePanel vertical siding THICKNESS FASTENER TYPE 5 FASTENER SPACING (IN) FRAME TYPE STUD SPACING (IN) ASD in. shank x.225 in x 1½ in. long ring shank nail 4 edge,8 field 2 x 4 wood d common, 2 in. long 4 2 x 4 wood d common, 2 in. long 4 2 x 4 wood d common, 2 in. long 6 2 x 4 wood d common, 2 in. long 6 2 x 4 wood No. 8 X 1 5/8 in. long X in. ribbed waferhead screw 6" OC vertically / 12" OC horizontally Attached to 7 / 16 " wood structural attached per code Min. No. 8 x 1 in. long x in. ribbed buglehead screw / 8 in. metal C stud Min. No. 8 x 1 in. long x in. ribbed buglehead screw / 8 in. metal C stud ET & F 0.10 in. knurled shank x 1½ in. long x 0.25 in. pin fastener (AKN NA) 4 edge,8 field 1 3 / 8 in. metal C stud ET & F 0.10 in. knurled shank x 1½ in. long x 0.25 in. pin fastener (AKN NA) 4 edge, 8 field 1 3 / 8 in. metal C stud No. 8 X 1.25" long X 0.323" 6" O.C. 1 3 / 8 in. metal C stud or 2 X 4 wood studs 2 No. 8 X 1.25"long X 0.323" 8" O.C. 1 3 / 8 in. metal C stud or 2 X 4 wood studs 2 Page 8 of 10

9 Table 3, Wind Design Table for HardiePanel vertical siding THICKNESS FASTENER TYPE 5 FASTENER SPACING (IN) FRAME TYPE STUD SPACING (IN) ASD No. 8 X 1.25 long X " O.C. 1 3 / 8 in. metal C stud or 2 X 4 wood studs 2 No. 8 X 1.25" long X 0.323" 12" O.C. 1 3 / 8 in. metal C stud or 2 X 4 wood studs 2 No. 8 X 1.25" long X 0.323" No. 8 X 1.25" long X 0.323" No. 8 X 1.25"long X 0.323" No. 8 X 1.25 long X No. 8 X 1.25" long X 0.323" No. 8 X 1.25" long X 0.323" 8" O.C. 6" O.C. into furring 8" O.C. into furring 10" O.C. into furring 12" O.C. into furring 8" O.C. into furring 1 3 / 8 in. metal C stud or 2 X 4 wood studs 2 framing with 3/4" thick by 3.5" wide wood furring or 20 ga. (33 mil.) steel furring 6,7,8,9 framing with 3/4" thick by 3.5" wide wood furring or 20 ga. (33 mil.) steel furring 6,7,8,9 framing with 3/4" thick by 3.5" wide wood furring or 20 ga. (33 mil.) steel furring 6,7,8,9 framing with 3/4" thick by 3.5" wide wood furring or 20 ga. (33 mil.) steel furring 6,7,8,9 framing with 3/4" thick by 3.5" wide wood furring or 20 ga. (33 mil.) steel furring 6,7,8, " shank X 0.215" x 1.5" long ring shank nail 6" O.C. into furring framing with 3 / 4 " thick by 3.5" wide wood furring 6,7,8 1 Installation must be in accordance with Section 4.2 of this report. 2 Values are for species of wood having a specific gravity of 0.42 or greater IBC Section , Eqn , IBC Section , Eqn , 5 Smooth shank stainless steel nails are outside of the scope of this report. 6 Furring attachment to structural members (framing) or alternative furring width shall be designed by the project engineer. 7 Wood furring shall be preservative treated per AWPA. 8 Wood furring shall be specific gravity of 0.42 or greater per AFPA/NDS, or wood structural panel, conforming to DOC PS 1 or DOC PS 2 or APA PRP The design and attachment of steel furring shall be the responsibility of the project engineer. Page 9 of 10

10 Table 4, Wind Design Table for HardieShingle Panel siding THICK. 1/4 FASTENER TYPE 4,5 FASTENER SPACING 0.090" shank x 0.215" x 1 long ring shank nail 4 8 FRAME TYPE 1,2 Attached to 7/16 wood structural panel sheathing STUD SPACING 7/16 WSP attached to framing per code ASD / " shank x 0.215" x 1 long ring shank nail 4 6 Attached to 7/16 wood structural panel sheathing 7/16 WSP attached to framing per code / " shank x 0.187" x 1 long ring shank nail 3 at each stud3 Nominal 2x / " shank x 0.187" x 1 long ring shank nail 3 at each stud3 Nominal 2x /4 ET&F pin x 1.5" x 0.313" at each stud Min. No. 20 ga. X 3.62" x 1.375" /4 ET&F pin x 1.5" x 0.313" at each stud Min. No. 20 ga. X 3.62" x 1.375" Values are for species of wood having a specific gravity of 0.40 or greater. 2 For application to metal framing members, fasteners must be ET & F Fastening Systems, Inc. ET&F Panelfast nail, ET & F No. AGS , head diameter = in., shank diameter = in., length = 1.5 in. Metal studs must be maximum Fy = 33 ksi. 3 For application to ASTM C90 concrete masonry unit wall, fasteners must be either ET & F Fastening Systems, Inc. ET&F block nail (ET & F No. ASM , head dia. = 0.30 in., shank dia. = 0.14 in., length = 1.25 in.), Max System block nail (CP C 832 W7 ICC, head diameter. = 0.30 in., shank diameter. = 0.15 in., length = 1.3 in.), Aerosmith SurePin block nail (head diameter = 0.30 in., shank diameter = in., length = 1.25 in.), or Jaaco Nail Pro (NP145S head diameter = 0.30 in., shank diameter = in., length = 1.25 in.) applied at the equivalent fastener or stud spacing. 4 For application to wood framing or wood based sheathing, the minimum fastener penetration must be 1 inch into framing or the sheathing thickness as applicable. 5 Smooth shank stainless steel nails are outside of the scope of this report James Hardie Building Products Inc. All rights reserved. TM, SM, and denote trademarks or registered trademarks of James Hardie Technology Limited. The International Building Code and International Residential Code trademarks are registered trademarks of International Code Council, Inc. Page 10 of 10