3/08 Rev EASY PLUG MANUAL All Devices. Bar Code Information

Transcription

1 3/08 Rev EASY PLUG MANUAL Bar Code Information Commonly used bar codes... 2 Code 2/5 Interleaved... 2 EAN 8 / EAN Code Code Code UPC... 5 EAN Codabar... 5 MSI... 6 ITF... 6 Code EAN UCC RSS family...7 RSS RSS Limited...9 RSS Expanded...9 Symbology selection...10 EAN UCC Composite Symbology...11 Notes about certain bar code types...13 EAN 128 and Code Listing of EAN Data designator (DD) numbers...14 Notes about bar code application...17 Quiet zones...17 Further information sources...18 Bibliographical references...18 Avery Dennison Barcode University...18 Index...19

2 2 Commonly used bar codes Ratio The following lists the most essential features of several very commonly used bar codes and the particularities to be observed when printing. An important criterion for differentiating between bar codes is the width of the elements. The elements bars and spaces are either variable or restricted to two values wide and narrow. In the latter case, the width relationship between wide and narrow elements is an important characteristic quantity. This width relationship is called a ratio. The ratio expresses the relationship in thickness between a narrow and a wide bar or between a narrow and a wide space. A ratio of 1:2 signifies that a wide bar a wide space is twice as wide as a narrow bar a narrow space. Code 2/5 Interleaved Each digit is represented by five bars / spaces two wide ones and three narrow ones. Digits having an odd position number are represented by bars and those having an even position number by spaces. In this way, two digits can be printed in an interleaved manner (hence the name) one digit with bars, the other with spaces between the bars. Characters Numeric (0 to 9) No. of print places Even-numbered (2, 4, 6,...) Bar code counter fields in Jetmark have a maximum length of 14 places. Ratio 1:2 to 1:3 1:2.25 to 1:3 if the narrow element is narrower than 0.5 mm. If a higher ratio is required, the identically constructed bar code ITF with a ratio of 1:2.5 can be used. Checksum Optionally, calculation can take place in Modulo 10. Other TTX 300 offline: Checksum can by switched on or off using the key combination Ctrl+F11. Pressing the F11 key displays whether the check digit is currently switched on/off (checksum enabled/disabled). EAN 8 / EAN 13 Code of the European Article Numbering (EAN) system. The EAN 8 (8 characters) and its wider variation, the EAN 13 (13 characters), have standardised dimensions. Characters Numeric (0 to 9) No. of print places Always 8 (EAN 8) or 13 (EAN 13) places with checksum in the last position. Ratio none Checksum Always in the last position; calculation by Modulo 10

3 3 Other EAN codes are assigned by: In Great Britain: Article Number Association UK Ltd. (ANA UK) 11 Kingsway London WC2B 6AR Tel Fax In France: GENCOD SARL 13 Boulevard Lefèvre Paris Tel Fax Module width at 100%: 0.33 mm Plain-text line (HRI): Instead of the OCR-B character set specified for this, Avery/Novexx uses Times Roman, but only on NISTAN (Non Standard Application) with specification of the bar code size. Code 39 Code 39 was the first alphanumeric code to be developed. Code 39 derives its name from the number of characters it was originally able to encode: 39. Today, the number of characters has been extended to over 43. Characters No. of print places Alphanumeric (0 to 9, 26 letters without umlauts, 7 special characters) Bar code count fields in Jetmark have a maximum length of 14 places Ratio 1:2 to 1:3 1:2.25 to 1:3 if the narrow element is narrower than 0.5 mm. TTX x50: YB7 = Ratio 1:2, YB16 = Ratio 1:3, YB19 = 1:2.5 TTX 300 Offline (2.04): YB7 = Ratio 1:2, YB16 and YB19 are not available TTX 300 Online (3.02): YB7 = Ratio 1:2, YB16 = Ratio 1:3, YB19 only for the US version of the printer Checksum No clear ratio because several bar intensities are used. Other Specification in accordance with EN 800 C-39 counter field also works with data such as "PL00124"

4 4 Code 93 Code 93 was developed as a completion to Code 39. Each character is represented in Code 93 using 9 modules which can be either black or white. Simultaneously, every encoded character consists of three bars and three spaces Code 93 is thus a (9.3) code, hence the name. Characters No. of print places Ratio Checksum 47 alphanumeric characters (0 to 9, 26 letters without umlauts, 11 special characters) Bar code count fields in Jetmark have a maximum length of 14 places No clear ratio because several bar intensities are used. is contained in the bar code but is not visible in the plain-text line; checksum cannot be switched off Code 128 Each character is represented in Code 128 by 11 modules which can either be black or white. Simultaneously, every encoded character consists of three bars and three spaces Code 128 is thus an (11.3) code. Characters The complete ASCII character set. Actually, Code 128 only has 106 different (bar) codes. For this reason, as the necessity arises, switching occurs between three different character sets Code A, Code B and Code C for each of which special codes exist. Please also read section EAN 128 and Code 128 on page 13. No. of print places Ratio Checksum Other Bar code counter fields in Jetmark have a maximum length of 14 places. No clear ratio because several bar thicknesses are used. is contained in the bar code but is not visible in the plain-text line; checksum cannot be switched off When running with Easy Plug (#YB13...), the stop character for CR/LF is printed additionally at the end of the bar code. This causes the software to jump to the next input field on scanning in. Append the Easy Plug termination command #G to the bar code command in order to suppress CR/LF. Switching between subset A, B and C takes place automatically in such a way that the bar code is as short as possible. Subset C can only encode numbers and here the number of places must be even. If only numbers are sent and if the number of places is even, Avery/ Novexx printers print in subset C.

5 5 UPC The Universal Product Code is the US-American counterpart of the European Article Numbering Code (EAN). UPC and EAN are compatible. In UPC, each character is represented by 7 modules which can be either black or white. Simultaneously, every encoded character consists of two bars and two spaces UPC is thus a (7.2) code. Characters Numeric (0 to 9) No. of print places Ratio Bar code counter fields in Jetmark have a maximum length of 14 places. No clear ratio because several bar intensities are used. Checksum Modulo 10, weighting 3/1 EAN 128 Corresponds to Code 128 with double start characters for Code A, B or C. Characters Alphanumeric, complete ASCII character set (0...,255) Can print all characters, even <20H. Required parameter setting: IFAC > <20H = NO, respectively SYSTEM PARAMETERS > Character filter = All characters No. of print places Ratio Checksum Other Bar code counter fields in Jetmark have a maximum length of 14 places. No clear ratio because several bar intensities are used. Calculated by Modulo 10, cannot be switched off. Switching between subset A, B and C takes place automatically. Function code <FNC1> is also transmitted automatically. Consecutive numbers possible. EAN codes are assigned by: Refer to section EAN 8 / EAN 13 on page 2. Please read in paragraph EAN 128 and Code 128 on page 13 for practical advices on using this bar code type with Easy Plug. Codabar Characters Numeric with special characters (0 to 9, -, $, :, /,., +) Ratio 1:2 to 1:3 Avery/Novexx printers: 1:2 Checksum Calculation by Modulo 16 Other Specification: EN 798 Codabar is not available in Jetmark 16.

6 6 MSI The modified Plessey Code (pulse-width modulated) from MSI Data Corporation. Characters Numeric (0 to 9) No. of print places Ratio 14 characters including checksum none Checksum Calculation by Modulo 10 Other Easy Plug: #YB-14 ITF ITF stands for Interleaved Two Five, ITF thus corresponds with Code 2/5 interleaved. Characters Numeric (0 to 9) No. of print places Even-numbered (2, 4, 6,...) Ratio Checksum Other 1:2.5 (in accordance with specification), size-dependent. An odd-numbered ratio would require the printing of half dots. This is why rounding takes place: 1:2.5 => 1:3 In the case of threefold magnification: 3:7.7 => 3:8 Calculation by Modulo 10 can be switched on/off ITF 8: 8 places ITF 14: 14 places Code 49 Specification Uniform Symbology Specification Code 49 (ANSI/AIM-BC6-2000) Characters All ASCII characters (128). Codable characters Easy Plug 2 rows: 9 alphanumerical or 15 numerical characters 8 rows: 49 alphanumerical or 81 numerical characters Command #CFN

7 7 EAN UCC RSS family The RSS (Reduced Space)-symbology is a new code family of linear symbols for very small components (f.e. health care, electronic and tele communication components), which need additional data for unique identification. The RSS family contains following 3 symbologies: RSS-14 RSS-Limited RSS-Expanded They are devided into mutations. Features of the RSS family Features of the RSS family: Barcode type RSS is a consecutive, linear barcode symbology, which can be read in both directions. A quiet zone is not required. Symbol character structure Different symbol characters (n,k) are used for each mutation of the RSS family, Whereas every symbol character consist of n modules within the width with k bars and gaps. Symbol characters can be border characters, search patterns or check characters. Data character The data characters don t comply with the coded data.to increase the codability, several thousand possibilities for data coding are available. They re based on mathematical combinations. Concatenation characters All RSS symbols contain a concatenation character, which is the first data character coded in a symbol. If the concatenation character is 0, then the RSS symbol is alone. If the concatenation character is 1, then a 2D component is printed above the RSS symbol. Encrypted character set RSS-14 versions and RSS Limited: digits 0 to 9. Limitation for RSS Limited: Only 0 or 1 is allowed at the fist position (indicator). RSS Expanded: a subset of table 1 international standard ISO\IEC 646 contained characters. Constists of upper and lower case characters, digits and 20 selected special characters, supplemented with the function character FNC1. Maximum numeric data capacity RSS-14 versions and RSS Limited: 14 digit nummeric identification. RSS Expanded: 74 nummeric or 41 alphanummeric characters. Data compression Every kind of the RSS family (RSS-14, RSS Limited, RSS Expanded use an own optimized compression method. RSS Expanded is additionally optimized for specific data element consequences, which are used very often.

8 8 RSS-14 RSS-14 RSS-14 supports the complete representation of the 14 digit EAN article number. Every symbol size is maller than the appropriate EAN-13 and UPC- A symbol size and supports a special concatinaten character. There are 4 versions available. RSS-14, RSS-14 Truncated (height reduced), RSS-14 Stacked (stacked) und RSS-14 Stacked Omnidirectional (direction and position independant readable). All 4 versions encode the data in the same manner, but are aligned respectively to special space and read conditions. Each symbol of the RSS-14 family contains 4 data characters and 2 search patterns. The 2 search patterns together encode the calculated modulo 79 check digit. The left and the the right border character of the symbol consist of a small bar and a small gap. RSS-14 needs no quiet zone. Each of the RSS14 symbols can be scanned and decoded in 4 segments, which are adjacent composed again. Thus the omnidirectional scanning is enabled. The RSS-14 was developed for units, which have to be read in omnidirectional scanning environments. The dimensions are 96X in the width, starting with a 1X wide gap and ending with a 1X wide bar. The height is 33X. X correspond to the width of a module. Fig. 1: Examples of a RSS-14 (left side) and a RSS-14 Stacked (right side). RSS-14 Truncated RSS-14 Stacked RSS-14 Stacked Omnidirectional The RSS-14 Truncated is a height reduced version of the RSS-14. The barcode isn t omni directional readable. The dimensions are 96X in width and 13X in height. X correspond to the width of a module. The RSS-14 Stacked is a height reduced, two rows version of RSS-14, developed for small volume units, which can not be scanned with omni directional scanners. The dimensions are 50X in width and 13X in height, inclusive of a 1X high separation pattern between the both rows. X correspond to the width of a module. The RSS-14 Stacked Omnidirectional is a two rows version of RSS-14 with a standard size, which was developed to be readable in omni directiona scanning environments. The dimensions are 50X in width and 69X in height, inclusive of a 3X high separation pattern between the both rows. X correspond to the width of a module.

9 9 Fig. 2: Example of a RSS-14 Stacked Omnidirectional. RSS Limited The RSS Limited was developed for identification of small products. The 14 digit EAN article identification can be coded. The RSS Limited codes the 14 digit EAN identification without the data identifier (DB) 01. Only a 14 digit EAN with a 0 or a 1 at the first position from left (indicator) can be used. The RSS Limited can t be used for EAN number structures with an identicator greater than 1, but a code from the RSS 14 has to be used. A RSS Limited symbol contains two data and and one check character, which is calculated with modulo 89. The left and right border character of the symbol consists of a small bar and a small gap. The RSS Limited needs no quiet zone. The RSS-14 Limited was developed for low quantity units and isn t readable omni directional.the dimensions are 74X in width and 69X in height, starting with a 1X wide gap and ending with a 1X wide bar, and 10X in height. X correspond to the width of a module. Fig. 3: Example of a RSS Limited. RSS Expanded The RSS Expanded family can encode all data elements of the EAN128 data identifier standard. The RSS Expanded and RSS Expanded Stacked allowes to encode up to 74 numeric or 41 alphanumeric characters. These symbols support a special concatenation character, which indicates that a 2D composite component is present. The RSS Expanded symbols can be read omni directional. The RSS Expanded has 2 mutations: with stacked and not stacked symbols. RSS Expanded symbols contain a check character and has dependant from symbol length, 3 to 21 data characters and 2 to 11 search patterns. The value of the check character is calculated with a modulo 211 algorithm. The left and the right border character of the symbol consist of a small bar and a small gap. RSS Expanded needs no quiet zone. RSS Expanded symbols can be scanned and decoded in 11 segments, which are adjacent composed again. Thus the omni directional scanning is enabled.

10 10 RSS Expanded The width of RSS Expanded is variable. The range is from 4 to 22 symbol characters or from 102X to 534X in width and 34X in height. The symbol starts with a 1X wide gap and ends either with a 1X wide bar or a 1X wide gap. X correspond to the width of a module. Fig. 4: Example of a RSS Expanded. RSS Expanded Stacked The RSS Expand Stacked is a multi row stacked version of RSS Expanded. This symbol can be printed in widths from 2 to 20 segments and can have 2 to 11 on top of each over stacked rows. There is a 3X high separation pattern between the rows. RSS Expanded stacked is used, if the symbol range or the print technology isn t suited for the (one row) RSS Expanded symbology. Symbology selection Each application of RSS has to be considered to the world wide valid EAN UCC application guidelines. RSS wasn t developed to replace other EAN UCC symbologies. Applications which can be satisfying covered with EAN/ UPC or UCC/EAN 128, shouldt be also used with these symbologies for the future. If RSS is used with units, which are read from omni directional slot scanners, RSS-14, RSS-14 Stacked Omnidirectional, RSS Expanded or RSS Expanded Stacked shouldt be used. If only one EAN article number with data identifier DB 01 is encoded, either RSS-14 or RSS-14 Stacked Omnidirectional shouldt be used. The decision for one of these symbols depends on the available area. If additional data elements are required or an other data element than the EAN article number with the data identifier DB 01 is used for the primary identification, the RSS Expanded or RSS Expanded Stacked has to be used. The selection of one of these both symbol depends on the print head width and the available area. If RSS shouldt be used on small units, which need no omni directional reading, RSS-14 Stacked, RSS Limited or RSS-14 Truncated are advised. RSS Limited can t be used to encode a EAN-14 number structure with an indicator value greater than 1. Otherwise RSS-14 or RSS-14 stacked has to used.

11 11 EAN UCC Composite Symbology The EAN UCC Composite Symbology merge as well a linear EAN UCC symbol as a 2 dimensional component. The linear component can be one of the following symbologies. EAN/UPC-Symbology (EAN-13, EAN-8, APC-A, UPC-E) Reduced Space Symbology (RSS) family UCC/EAN 128 The 2D Composite Component (CC) is selected because of the linear component and the amount of characters which shouldt be encoded. Follwing mutations exist: CC-A, a variation MicroPDF417 with up to 56 numbers CC-B, a MicroPDF417 symbol with new encoding rules and up to 338 numbers CC-C, a PDF417 symbol with new encoding rules and up to 2361 numbers Linear component CC-A/CC-B CC-C UPC-A and EAN13 Yes (4 columns) No EAN 8 Yes (3 columns) No UPC-E Yes (2 columns) No UCC/EAN 128 Yes (4 columns) Yes (variable width) RSS-14 Yes (4 columns) No RSS-14 Truncated RSS-14 Stacked Yes (2 columns) No RSS-14 Stacked Omnidirectional RSS Limited Yes (3 columns) No RSS Expanded Yes (4 columns) No [Tab. 1] List of all combinations of linear EAN UCC symbols with a 2D Composite Component. Symbol Characteristic Omnidirection al readable Stacked Additional informations Very small symbol RSS-14 Yes No No No RSS-14 No No No Yes Truncated RSS-14 Stacked No Yes No Yes RSS-14 Stacked Yes Yes No No RSS Limited No No No Yes RSS Expanded Yes No Yes No RSS Expanded Stacked Yes Yes Yes No [Tab. 2] Features overview of Reduced Space symbol formats with a 2D Composite Component.

12 12 Symbol 2D Composite Component Characteristic Omnidirection Stacked Additional Very small al readable informations symbol No Yes Yes Yes [Tab. 2] Features overview of Reduced Space symbol formats with a 2D Composite Component.

13 13 Notes about certain bar code types #YB15 Example <FNC1>, <FNC4> <FNC2> <FNC3> Subsets A, B, C EAN 128 and Code 128 By giving the bar code command #YB15 (= EAN 128), the function code <FNC1> required after the start character is automatically generated and must not be specifically entered. Every coded data contents must be preceded by its data designator number. Refer to in paragraph Listing of EAN Data designator (DD) numbers on page 14 for detailed information. Data contents of variable length must always be terminated by entering <FNC1> (including the brackets). Exception: the last data contents does not require the termination character. EAN 128 with 3 data designators #YB15////// <FNC1> = EAN article number (fixed length) 10 = Charge number (variable length) 21 = Serial number (variable length) are available for specifically defining the bar code scanner. (Information reference): <FNC2> temporarily stores the symbol data which contains the <FNC2> character in the bar code scanner, and transfers it to the next data symbol. This can be used to line up different symbols before they are transferred. <FNC2> can appear at any position in the symbol. (Initialisation): The bar code scanner interprets the data of the symbol which contains the <FNC3> character as an instruction for initialising or reinitialising the bar code scanner. The symbol data is not transmitted by the bar code scanner. <FNC3> can appear at any position in the symbol. The 64-xx bar code library contains four versions of code 128 which differ in the characters they use (refer to the table). Easy Plug Bar code Subset Number 15 EAN 128 Changes automatically between the subsets A, B and C in order to achieve a possibly short bar code. 13 Code 128 Changes automatically between the subsets A, B and C in order to achieve a possibly short bar code. 24 Code 128 A Subset A 25 Code 128 B Subset B 26 Code 128 C Subset C [Tab. 1] Every Subset of EAN 128 / Code 128 matches with an Easy Plug bar code number.

14 14 Please keep to the following rules, when using EAN 128 / Code 128 with Easy Plug: The bar code data has to be terminated with #G. When using data designators with a variable field length, the field must be closed by <FNC1>. Exception: The field is placed at the bar code end. Data designator 00 (Serial Shipping Container Code): Always enter all 18 digits including the check digit after this designator. The printer always calculates and replaces the check digit automatically. This enables an automatic numbering of the serial shipping container code. The offset value has to consider all characters placed on the right side of the increment digit position. Example: #YB15/0B/2/3/10000/1/(00) (10)Charge1#G Data designator 01 (EAN-No.): Always enter all 14 digits including the check digit after this designator. The printer doesn t check or modify the check digit. Listing of EAN Data designator (DD) numbers DD Data content Format * 00 Serial shipping container code n2+n18 01 EAN number n2+n14 02 Reserved for: EAN-number of goods contained within n2+n14 another unit. 10 Lot number / Batch number n2+an ** Manufacturing date (JJMMTT) n2+n6 13** Packing date (JJMMTT) n2+n6 15** Best before date (JJMMTT) n2+n6 17** Expiration date (JJMMTT) n2+n6 20 Product variant n2+n2 21 Serial number n2+an Reserved for: HIBCD-quantity, date, batch and link. n2+an Reserved for: Lot Number (transitional use) n3+n Amount in pieces (trade unit with variable amount) n2+n *** Netweight, kilogram (trade unit with variable n4+n6 amount) 311*** Length or 1st dimension (trade unit with variable n4+n6 amount) 312*** Width, diameter or 2nd dimension, meter (trade unit n4+n6 with variable amount) 313*** Height or 3rd dimension (trade unit with variable amount) n4+n6 [Tab. 2] Listing of EAN data designators.

15 15 DD Data content Format * 314*** Area, square meters (trade unit with variable n4+n6 amount) 315*** (Net) volume, liter (trade unit with variable amount) n4+n6 316*** (Net) volume, cubic meter (trade unit with variable n4+n6 amount) 320*** Reserved for: Netweight, (engl.) pounds n4+n6 330*** Gross weight, kilogram n4+n6 331*** Length or 1st dimension, meter n4+n6 332*** Width, diameter or 2nd dimension, meter n4+n6 333*** Height or 3rd dimension, meter n4+n6 334*** Area, square meter n4+n6 335*** (Gross) volume, liter n4+n6 336*** (Gross) volume, liter n4+n6 340 Reserved for: Gross weights, (engl.) pounds n4+n6 37 Reserved for: Quantity n2+n Order number of the consignee n3+an n3+n n3+n n3+n n3+an n3+n3+an Reel product, -width, length, inner diameter, reel direction, splices n4+n Reserved for Electronic Serial Number for Cellular n4+an..30 Mobile Telephones 90 Internal and/or bilateral coordinated applications n2+an Internal - raw material, packaging, components n2+an Internal - raw material, packaging, components n2+an Internal - manufacturer n2+an Internal - manufacturer n2+an Internal - carrier (consignment note etc.) n2+an Internal - carrier (consignment note etc.) n2+an Internal - wholesale and retail trade n2+an Internal - wholesale and retail trade n2+an Bilateral coordinated texts n2+an..30 [Tab. 2] (Cont.)Listing of EAN data designators. *. First position = length (no. of characters) of the data designator, following position = data format (Table 3 on page 16). **. Fill TT with 00, if only year and month shall be considered. ***.The fourth digit indicates the no. of decimal places. Examples: 3100 = net weight in kg without decimal place = net weight in kg with two decimal places.

16 16 Acceptable data format a n an a3 an3 n3 a..3 n..3 an..3 [Tab. 3] alphabetical character numerical character alphanumerical character 3 alphabetical characters, fixed data field length 3 alphanumerical characters, fixed data field length 3 numerical characters, fixed data field length up to 3 aalphabetical characters up to 3 numerical characters up to 3 alphanumerical characters Abbreviations of the acceptable data formats.

17 17 Notes about bar code application Quiet zones Quiet zones are bright, blank areas on the right and left side of the bar code (in reading direction). They are necessary for error-free reading. Ruhezonen / Quiet zones Z0160.cdr Fig. 5: Quiet zones are important for error-free bar code reading. Measures The following typical values apply to quiet zones: Scanner with average depth-of-focus: 10x the module width of one element, at least 2.5 mm. Scanner with high depth-of-focus: 15x the module width of one element, at least 6.5 mm.

18 18 Further information sources Bibliographical references You can find detailed information on bar codes in the following books, among others: Palmer, Roger C.: The Bar Code Book, Helmers Publishing Inc., Petersborough, 1989, ISBN Rosenbaum, Oliver: The Bar code Encyclopaedia ( Das Barcode- Lexikon ), bhv Verlags GmbH, Kaarst, 1997, ISBN Avery Dennison Barcode University For detailed Information about bar codes, further bibliographical references and Internet links, refer to the followint Internet page:

19 19 Index B Bar 13 Bar code Info EAN 128 and C Codabar 5 Code Code 2/5 Interleaved 2 Code 39 3 Code 93 4 Composite Symbology 11 D Data formats 16 E EAN 2 EAN EAN Data designator (DD) numbers 14 Easy Plug bar code number 13 European Article Numbering 2 I ITF 6 M MSI 6 R Ratio 2 RSS 7 RSS Expand Stacked 10 RSS Expanded 9 RSS Limited 9 RSS-14 8 RSS-14 Stacked 8 RSS-14 Stacked Omnidirectional 8 RSS-14 Truncated 8 S Subsets, 13 U Universal Product Code 5 UPC 5