HiPath HiPath 1120 HiPath 1130 HiPath 1150 HiPath Instruction Manual System Telephone Profiset 3030

Transcription

1 HiPath 1100 HiPath 1120 HiPath 1130 HiPath 1150 HiPath 1190 Instruction Manual System Telephone Profiset 3030

2 Contents Installation Recommendations... 3 Installation... 4 Profiset 3030 System Telephone... 5 Characteristics... 5 Status Indication Keys... 7 Function Keys for Profiset S30058-H6202-A1/A2.. 8 Function Keys for Profiset S30058-H6202-C5/C6.. 9 Configuration Adjusting the Ring Volume Adjusting the Ring Melody Adjusting the Reception Volume Dialing Mode Display Brightness Time Format Adjusting the Hands-free Volume Other Settings Diagram of the Navigation Menu

3 Installation Recommendations Installation Recommendations Place the telephone on a non-slip surface. Polished or varnished surfaces can be marked by some parts of the telephone, such as the rubber feet. To ensure good hands-free conversation quality, place the telephone on a flat surface and keep the area in front of the microphone free of obstructions. To avoid interference, keep the telephone at least one meter away from cordless telephones, mobile telephones, television sets and other electrical equipment. The Profiset 3030 telephone must be installed at a maximum distance of 500 meters from the telephone exchange by using a two-pair cable with 0.4mm 2 copper wire. The telephone must not be exposed directly to the sun or other heat sources, nor be installed in dusty or excessively humid locations, as this will reduce its useful life. It should be used at temperatures between 5 ºC and 50 ºC and it is not waterproof. To clean the telephone, use a damp cloth and avoid abrasive cleaning products. Do not use a dry cloth, because it may cause electrostatic discharges that could damage the equipment. When the telephone reaches the end of its useful life, dispose of it in a way that does not harm the environment, in accordance with local legal requirements. CE Mark The device conforms to the EU guideline 99/5/ ECC, as attested by the CE mark. 3

4 Installation Recommendations Installation Connecting the Handset to the Telephone: Insert the long, straight end of the spiral cord into the connector with the symbol, until it snaps in. Connect the short end to the handset. Press the cord into the cable guide. Line Cord Connection Insert one end of the straight cord into the connector with the symbol and the other end into the phone jack of the extension to which you want to connect the equipment. Press the cord into the cable guide. Labeling Strip Your Profiset 3030 telephone has a labeling strip for writing down names, telephone numbers and functions stored in the programmable keys. If you need to change the labels, cut out the template supplied on the last page of this manual. 4

5 Profiset 3030 System Telephone Profiset 3030 System Telephone This is a telephone exclusive to the HiPath 1100 and euroset line systems. It allows direct access to some PABX features, and has special functions for monitoring the status of external lines and extensions using signals from a group of programmable keys. Characteristics It has a 3-line display The first line displays the MUTE symbol, the repeat call counter, the repeat call indicator, and the time and date. The time is shown in 24-hour or AM/PM (hours:minutes) format and the date in day/month format (for example, 11:13 28/08). When you are in operator terminal mode, the number of unanswered internal, external and recalled calls is shown on the second line (16 digits). The messages are shown, 16 characters, on the third line. 1. MUTE indicator symbol activated 2. Repeat call counter 3. Time 4. AM/PM indicator 5. Date 6. Repeat call indicator 7. Field for operator terminal 8. Field for alphanumeric characters 5

6 Profiset S30058-H6202-A1/A2 Profiset 3030 System Telephone Profiset S30058-H6202-C5/C6 1. Handset cradle 2. Function keys 3. Programmable keys with status indicator LEDs 4. Hands-free loudspeaker 5. Hands-free microphone 6. Display 6

7 Status Indication Keys Profiset 3030 System Telephone Key off; the extension or external line is free. Key blinking slowly; a call is parked. Key blinking faster; an incoming call to the extension has not been answered. Key blinking fastest; signals an incoming call or a recall. Key is on; the extension is busy. 7

8 Profiset 3030 System Telephone Function Keys for Profiset S30058-H6202-A1/A2 FWD key forwards calls to an extension or external telephone. PARK key parks a call. HOLD key puts a call on hold. SPEAKER key, activates hands-free mode using microphone and loudspeaker. REDIAL key redials the last number called 1. MENU key for access to menu-driven configuration settings. FLASH key invokes the flash function for the external line. FEATURE key activates the system functions (for example, Forward, Do not disturb, etc). MUTE key deactivates voice transmission so the person with whom you are speaking cannot hear you any more. To reactivate voice transmission, press the key again. Confirmation key Menu navigation key Menu navigation key 1.The REDIAL function key is only used for telephone MENU navigation 8 on HiPath systems.

9 Profiset 3030 System Telephone Function Keys for Profiset S30058-H6202-C5/C6 NOTE: Profiset 3030 S30058-H6202-C5/-C6 can only be used in Version 5.2. Navigation Key Shows PREVIOUS option Navigation Key. Shows NEXT option. Confirmation Key Selects (confirms) the displayed option. SPEAKER key, activates hands-free mode using microphone and loudspeaker. REDIAL key redials the last number called. MENU key for access to menu-driven configuration settings. FLASH key invokes the flash function for the external line. FEATURE key activates the system functions (for example, Forward, Do not disturb, etc). MUTE key deactivates voice transmission so the person with whom you are speaking cannot hear you any more. To reactivate voice transmission, press the key again. 9

10 Configuration Configuration For greater user convenience, the Profiset 3030 system telephone provides some configuration options. The following keys are used in configuration mode: Profiset S30058-H6202-A1/A2 and or and h Profiset S30058-H6202-C5/C6 and or and h Adjusting the Ring Volume The ring volume can be adjusted to 6 levels.the ring volume is preset to level 6. Telephone in Idle State: Replace the handset. Ring Volume 1 Ring Volume 2 or and Press this key to enter configuration mode. With the or keys, locate the ring volume option on the display. Press this key to select the ring volume adjustment option. Use the or key to change the ring volume. After choosing a volume level, press this key to confirm. Continue navigating through the menu options or press the Menu key to finish the configuration. 10

11 Configuration Adjusting the Ring Melody You can choose among 3 ring melodies. Telephone in Idle State: Replace the handset. melody 1 melody 1 or and Press this key to enter configuration mode. With the or keys, locate the melody option on the display. Press this key to select the melody selection option. Use the or keys to hear the ring melody. Choose a melody and press this key to confirm. Continue navigating through the menu options or press the Menu key to finish the configuration. 11

12 Adjusting the Reception Volume Configuration The reception volume on the Profiset 3030 can be adjusted during a conversation (6 levels). The reception volume is preset to level 4. volume RX 1 volume RX 1 or and Press this key to enter configuration mode. With the or keys, locate the volume RX option on the display. Press this key to select the volume RX option. Use the or keys to change the reception volume. After choosing a volume level, press this key to confirm. Continue navigating through the menu options or press the Menu key to finish the configuration. 12

13 Dialing Mode Configuration If your system is not working because of a power outage and the external telephone line has been switched directly to your Profiset 3030 system telephone, you will need to specify the dialing mode (pulse or tone) for this line, because in normal operation the telephone exchange performs this setting automatically. Telephone in Idle State: Replace the handset. Press this key to enter configuration mode. Mode Mode or tone tone and With the or keys, locate the mode option on the display. Press this key to select the mode option. Use the or keys to choose the dialing type, Tone or Pulse. After choosing a dialing mode, press this key to confirm. Continue navigating through the menu options or press the Menu key to finish the configuration. Temporary Change of Dialing Mode: When the telephone is set to PULSE dialing, you may occasionally need to temporarily change the dialing mode to TONE dialing. Example: You want to check your bank balance using your telephone banking service. Make the call as you usually would and, as soon as the call is completed, press to change the dialing mode to TONE dialing. When you finish the call, just hang up and the dialing mode will automatically switch back to PULSE dialing. 13

14 Display Brightness Configuration The display brightness can be adjusted to 3 levels; it is preset to level 2. Telephone in Idle State: Replace the handset. bright 1 bright 1 or and Press this key to enter configuration mode. With the or keys, locate the bright option on the display. Press this key to select the bright option. Use the or key to select one of the 3 brightness levels. After choosing a brightness level, press this key to confirm. Continue navigating through the menu options or press the Menu key to finish the configuration. 14

15 Time Format Configuration The time can be shown on the display in 24-hour or AM/PM format. Telephone in Idle State: Replace the handset. Format format or 24 hs am pm and Press this key to enter configuration mode. With the or keys, locate the format option on the display. Press this key to select the format option. Use the or keys to select 24 hs or am pm. After choosing a format, press this key to confirm. Continue navigating through the menu options or press the Menu key to finish the configuration. 15

16 Adjusting the Hands-free Volume Configuration You can adjust the hands-free volume (6 levels) on the Profiset 3030 during a conversation. The hands-free volume is preset to level 4. Telephone in Hands-free Mode: Press this key to switch to handsfree mode. Press this key to enter configuration mode. vol hands-free 1 Use the or keys to select one of the 6 volume levels. Press this key to finish the configuration. Other Settings You can make additional settings with the following sequence: + + Code Code Description 00 Sets DTMF 85/85ms and enables DTMF mode 01 Sets DTMF 140/85ms and enables DTMF mode 16

17 Configuration Code Description 02 Sets pulse dialing open/closed ratio to 2:1 (33/66ms) and enables pulse dialing 03 Sets pulse dialing open/closed ratio to 1.5:1 (40/60ms) and enables pulse dialing 04 Automatic gain control disabled 05 Automatic gain control enabled 06 Ring frequency discrimination in the 15-75Hz range (in case of power outage) 07 Ring frequency not discriminated 08 Line impedance 600 Ω (in case of power outage) 09 Line impedance 1000 Ω (in case of power outage) 10 DTMF 85/85ms 11 DTMF 140/85ms 12 Pulse dialing proportion open/closed 2:1 (33/66ms) 13 Pulse dialing proportion open/closed 1.5:1 (40/60ms) 14 Time format DD/MM 15 Time format MM/DD 20 This code cancels the language setting configured by the user (manual configuration) and activates the system's default setting (automatic configuration). 21 Portuguese (Brazil) 22 Portuguese (Portugal) 23 English (default) 24 French 25 Spanish 31 Normal level of transmission 32 High level of transmission 33 Very high level of transmission 99 Return to factory programming For more detailed feature explanations, refer to your telephone exchange s user guide. 17

18 Diagram of the Navigation Menu Diagram of the Navigation Menu Level 1 Level 2 Level 3 Menu 1 2 RING VOLUME MELODY MODE TONE PULSE FORMAT 24 HS AM PM BRIGHT VOLUME RX

19

20

21

22 Produzido no Pólo Industrial de Manaus A31003-K1250-B P A31003-K1250-B The information in this document contains general descriptions of the technical options available, which do not always have to be present in individual cases. The required features should therefore be specified in each individual case at the time of closing the contract. Ref. No.:A31003-K1250-B Printed in Brazil Siemens Ltda 2006 Rua Pedro Gusso, 2635 Curitiba-PR/BR Subject to availability. Right of modification reserved.