PLC-RS /21. PLC INTERFACE With PDT Relay, Universal Version. INTERFACE Data Sheet _en_02. 1 Description

Transcription

1 PLC INERFCE With PD Relay, niversal Version INERFCE Data Sheet 780_en_02 PHOENIX CONC - 03/08 Description PLC-RS /2 relay modules, which can be used universally, comprise 6.2 mm basic terminal blocks and plug-in miniature relays with PD contact and screw or spring-cage connection.. PD Offers a High Degree of Flexibility he PLC-RS /2 universal PD module is used whenever an application requires a high degree of flexibility. It can be used either as an input or output module or in N/O, N/C or PD contact applications. his offers the advantage of fewer ordering and warehousing items. PLC INERFCE modules are supplied fully equipped with a relay as standard..2 Input Voltages From 2 V to 230 V PLC-RS /2 is available on the coil side in all common industrial voltages from 2 V to 230 V. further advantage is the ready-integrated input circuit. It consists of a status indicator as well as free-wheeling diode and polarity reversal protection function, and ensures that the operating state is displayed clearly, also offering reliable EMI suppression for the coils and preventing destruction should the polarity be accidentally reversed..3 Optimum se of Plug-In ridges he PLC INERFCE module achieves maximum efficiency with the user-friendly FS plug-in bridge system. he PLC-RS /2 makes effective use of the bridging options for the /2 connection on the coil side and for the grouped power supply at connection on the contact side. Especially effective here are the 500 mm long colorinsulated continuous plug-in bridges that can easily be cut to the required length and quickly inserted in the bridge shafts. hey eliminate the need for complicated and timeconsuming loop bridges..4 dditional dvantages Operational safety with R III (IP67)-protected mechanics Environmentally friendly, cadmium-free power contact material for loads up to 250 V C/6 vailable with gold coating for low power levels (m) as an option Integrated input circuit Relay can be replaced using an engagement lever Safe isolation according to DIN EN 5078 Inflammability class V0 according to L94 Make sure you always use the latest documentation. It can be downloaded at conversion table is available on the Internet at his data sheet is valid for all products listed on the following page:

2 2 Ordering Data PLC INERFCE With Screw Connection Description ype Order No. Pcs./Pck. PLC INERFCE With Multi-Layer Contact Relay, niversal Version PLC INERFCE, comprising PLC-SC.../2 (see INERFCE catalog), for mounting on 3 2 V DC PLCRSC- 2DC/2 24 V DC PLCRSC- 24DC/2 24 V C/DC PLCRSC- 24C/2 48 V DC PLCRSC- 48DC/2 60 V DC PLCRSC- 60DC/2 V C/ V DC PLCRSC-C/2 230 V C/2 V DC PLCRSC-230C/2 PLC INERFCE With Power Contact Relay, niversal Version PLC INERFCE, comprising PLC-SC.../2 (see INERFCE catalog), for mounting on 3 2 V DC PLCRSC- 2DC/2 24 V DC PLCRSC- 24DC/2 24 V C/DC PLCRSC- 24C/2 48 V DC PLCRSC- 48DC/2 60 V DC PLCRSC- 60DC/2 V C/ V DC PLCRSC-C/2 230 V C/2 V DC PLCRSC-230C/ he PLC-P K insulating plate must be installed for voltages greater than 250 V (L, L2, L3) between the same terminal points on adjacent modules (see "ccessories"). FS 8-PLC... or FS is then used for potential bridging. PLC INERFCE With Spring-Cage Connection Description ype Order No. Pcs./Pck. PLC INERFCE With Multi-Layer Contact Relay, niversal Version PLC INERFCE, comprising PLC-SC.../2 (see INERFCE catalog), for mounting on 3 2 V DC PLCRSP- 2DC/2 24 V DC PLCRSP- 24DC/2 24 V C/DC PLCRSP- 24C/2 48 V DC PLCRSP- 48DC/2 60 V DC PLCRSP- 60DC/2 V C/ V DC PLCRSP-C/2 230 V C/2 V DC PLCRSP-230C/2 PLC INERFCE With Power Contact Relay, niversal Version PLC INERFCE, comprising PLC-SC.../2 (see INERFCE catalog), for mounting on 3 2 V DC PLCRSP- 2DC/2 24 V DC PLCRSP- 24DC/2 24 V C/DC PLCRSP- 24C/2 48 V DC PLCRSP- 48DC/2 60 V DC PLCRSP- 60DC/2 V C/ V DC PLCRSP-C/2 230 V C/2 V DC PLCRSP-230C/ he PLC-P K insulating plate must be installed for voltages greater than 250 V (L, L2, L3) between the same terminal points on adjacent modules (see "ccessories"). FS 8-PLC... or FS is then used for potential bridging. With the V and 230 V modules, an REL-MR-60DC/ V relay is normally used due to the input circuit integrated in the basic terminal block. For the protection of input and output, inductive loads must be dampened with an effective protective circuit. 780_en_02 PHOENIX CONC 2

3 ccessories Description ype Order No. Pcs./Pck. Insulating plate PLC-P K he PLC-P K insulating plate should be used in the following cases: always fit at the start and end of a PLC terminal strip for voltages greater than 250 V (L, L2, L3) between the same terminal points on adjacent modules (FS 8-PLC... or FS can be used for potential bridging) and for safe isolation between adjacent modules. For additional accessories such as power terminal blocks and plug-in bridges, please refer to the INERFCE catalog or 3 echnical Data Input Data...24DC C......C C... Nominal input voltage 24 V DC 24 V C/DC V C/ V DC Permissible range (with reference to N ) See "Operating Voltage Ranges" on page V C/ 2 V DC ypical input current at N 9 m m/8.5 m 3.5 m/3 m 3 m ypical response time at N 4 ms 6 ms 6 ms 7 ms ypical release time at N 8 ms 5 ms 5 ms 5 ms Input circuit Yellow LED, protection against polarity reversal, freewheeling diode Yellow LED, bridge rectifier he PLC-P K insulating plate must be installed for voltages greater than 250 V (L, L2, L3) between the same terminal points on adjacent modules (see "ccessories"). FS 8-PLC... or FS is then used for potential bridging. Output Data PLC-...2 PLC-...2 Contact type Single contact, SPD Contact material gsno gsno + 5 μ Maximum switching voltage 250 V C/DC 2 30 V C/36 V DC Minimum switching voltage 2 V C/DC 0 mv Limiting continuous current 6 50 m Maximum inrush current 30 (for C 5 operation) 50 m Minimum switching current m m Maximum shutdown power Ohmic load τ = 0 ms Ohmic load τ = 0 ms 24 V DC 48 V DC 60 V DC V DC 2 V DC 250 V C 40 W W 8 W 23 W 40 W 500 V.2 W Minimum switching power mw μw If the specified maximum values are exceeded, the gold coating will be damaged. In subsequent operation, the gsno contact values given here will apply. his can then result in reduced service life, similar to dedicated power contacts. 2 he PLC-P K insulating plate must be installed for voltages greater than 250 V (L, L2, L3) between the same terminal points on adjacent modules (see "ccessories"). FS 8-PLC... or FS is then used for potential bridging. General Data Impulse voltage withstand level mbient temperature range Operation Storage/transport Nominal operating mode Inflammability class according to L 94 (housing) Mechanical service life 4 kv, 50 Hz, min. -25 C C (230 V type -25 C C) -40 C C 0% operating factor V0 2 x 7 cycles 780_en_02 PHOENIX CONC 3

4 General Data (Continued) ir and creepage distances between the circuits IEC 60664, IEC 60664, DIN VDE 0, DIN EN 5078/VDE 06-60, IEC 60255/DIN VDE 0435 Pollution degree 3 Surge voltage category III Mounting position ny Mounting Can be aligned without spacing Conductor cross-section Solid, with screw connection 0.4 mm mm 2 (26-4 WG) Stranded, with screw connection 0.4 mm mm 2 (26-4 WG) Solid, with spring-cage connection 0.2 mm mm 2 (24-4 WG) Stranded, with spring-cage connection 0.2 mm mm 2 (24-4 WG) Stripping length Screw connection mm Spring-cage connection 8 mm Dimensions (W x H x D) 6.2 mm x 94 mm x 80 mm Housing material Polyamide P, green he PLC-P K insulating plate must be installed for safe isolation between adjacent modules (see "ccessories"). FS 8-PLC... or FS is then used for potential bridging. ests/pprovals CE L GL c u F 4 lock Diagram 2 ) 4 2 ) he input circuit depends on the type 780_en_02 PHOENIX CONC 4

5 5 Operating Voltage Ranges N N =24VDC N N= V DC / V C Figure Operating voltage range for 24 V DC Figure 3 Operating voltage range for V C/DC N N =24VDC/24VC N N= 2V DC / 230V C Figure 2 Operating voltage range for 24 V C/DC Figure 4 Operating voltage range for 230 V C/DC General Conditions Direct alignment in the block, all devices 0% operating factor, horizontal or vertical mounting. Curve Maximum permissible continuous voltage max with limiting continuous current on the contact side Curve Minimum permissible operate voltage op following preexcitation 780_en_02 PHOENIX CONC GmbH & Co. KG lomberg Germany Phone: PHOENIX CONC P.O.ox 40 Harrisburg P 7-00 S Phone: