Transcription

1 Seite 1 von 15 Configuration assistant An assistant guides you step by step through the customization process: Tacho function Speed signal ca be monitored for each fan channel.

2 Seite 2 von 15 Manual Mode and Monitoring You can take over control and immediately active manual controls and influence the fan speeds directly. Calibration of sensors The sensors must be calibrated according to the distance between the sensors and the origin of heat. This is easily accomplished with softwar system monitors that come with the mainboard (like Asus Probe, Intel Active Control, and more).

3 Seite 3 von 15 Definition of limits Here you can define the temperature limits. Above these limits all fans speeds will be operating at 100%. Under these limits the speed will ran according to the measured temperatures. A delay (hysteresis) can be defined with "leave values. Assignment between sensors and fans

4 Seite 4 von 15 Sensors can be assigned to the 4 fan channels in any possible way, giving you a free configuration of sensors to channels. You can even confi them so as to have several sensors connected to a single channel, or have a single sensor being used by several channels. also assignable using a comprehensive matrix:

5 Seite 5 von 15 Speed-Temperature response curves editable The user can chose from a variety of predefined profiles or can freely design their own curve with 5 definition points which connect to a curve You can design a different curve for every channel. The input of the curve is the measured temperature (the highest if more than one sensor related to the actual channel). The output of the curve is the performance of the fans (0-100%) Control to target temperature You can control each fan channel to meet a certain target temperature.

6 Seite 6 von 15 Control with MBM mainboard internal sensors You can use the internal mainboard sensors to control the speed. All you need is Motherboard Monitor (MBM). Just assign the MBM sensor to y fan channels: The tool MBM has to be installed and has to run in parallel. Only values, which MBM delivers can be analysed by the T-Balancer software.

7 Seite 7 von 15 Water cooling system support You can connect up to 2 flowmeters from different manufacturers. You can also adjust the impulse rate to your model. In addition you have a hardware emergency switch off and can connect up to 6 analog water temp probes. Controlling CCFLs You can also control CCFLs instead of fans. You can choose this option for each channel. Load an effect or create your own with an effect edito

8 Seite 8 von 15 Changing Profiles with timing You can plan different profiles for different times. The T-Balancer will change automatically the profiles. Ping the digital sensors

9 Seite 9 von 15 Define Quickbuttons You can assign to each of the 5 quickbuttons profiles or navigation menues.

10 Seite 10 von 15 Individual navigation profiles Here you can disable all navigation menues, which you do not need. This adapts the software interface to your needs.

11 Seite 11 von 15 Coastdown control system You can configure, if your system should accelerate to 100% fan speed while closing the TBAN software. blows all remaining warm air out of the PC. FanAmp support If you want to connect an FanAmp to one of your fan channels, then you have to invert the signal. Sig invertation changes 100% to 0% and 0% to 100%. Please do this only for the channels, which are con to the FanAmp, otherwise your TBAN will react the wong way. Connect the FanAmp to a channel brings more power and true analog voltage signals to the fans or w pumps.

12 Seite 12 von 15 Configuration of the mining The mining works completely autonom and can also be operated without the T-Balancer. But if you own a T-Balancer you can make all configurations with Software and you can create new profiles and save them to the mining. bigng support

13 Seite 13 von 15 Integration with JaLCD You can show the actual values like temperature, speed, alarm over a LCD with the software JaLCD. JaLCD is Freeware and supports the following LCDs: HD44780-compatible LCD and Crystalfontz serial displays jalcds can show information like: T-Balancer temperatures and speed, CPU speed and -usage, memory, HDD Infos, date/ time, upload speed, MBM values, Winamp infos, infos, Newstickers, TV program and much more. Integration with LCDC Many Thanks to Andrew Powell, who provided an interface to LCDC: Allows for retrieval of: - Alarm State - Alarm Description

14 Seite 14 von 15 - All Digital and Analogue Temps - Names, Values - 2 Flow meters - Names, Rates, Units - 4 Fans - Names, Temps and Percentage Integration with Samurize Over an interface to Samurize you can choose of many desktop motives to monitor T-Balancer values. Integration with imon VFD imon VFD is the most advanced IR receiver and VFD display device in the market. It not only delivers IR signal to PC but also shows various u information through VFD. It is designed to fit into the 5.25 disk drive bay of PC. It shows Graphical EQ, System Info, Media Info News, World City Time & Weather and more. All the information could be displayed automatically according to the scenario. Of course, user choose the specific information with remote controller too. And one more feature of this imon VFD is use can boot a PC with preset schedule. this scheduled turn on feature, you can listening music or recording TV channel by Multi-Median. With the following interface, provided by Robin, you can also monitor T-Balancer values: Integration with LCD Smartie Many thanks to Peter in the forum Silenthardware.de. Download here.

15 Seite 15 von 15 Monitoring over net With NView you can monitor each T-Balancer in a network from any PC. Analysing history With an Excel tool you can read the history data out of the database and analyse it. Linux support Your are invited to support the Linux developments. Driver, communication protocol and programming examples are