1 How do I install Active Directory on my Windows Server 2003 server? Here is a quick list of what you must have: An NTFS partition with enough free space An Administrator's username and password The correct operating system version A NIC Properly configured TCP/IP (IP address, subnet mask and - optional - default gateway) A network connection (to a hub or to another computer via a crossover cable) An operational DNS server (which can be installed on the DC itself) A Domain name that you want to use The Windows Server 2003 CD media (or at least the i386 folder) Brains (recommended, not required...) Step 1: Configure the computer's suffix (Not mandatory, can be done via the Dcpromo process). 1. Right click My Computer and choose Properties. 2. Click the Computer Name tab, then Change.
2 3. Set the computer's NetBIOS name. In Windows Server 2003, this CAN be changed after the computer has been promoted to Domain Controller. 4. Click More. 5. In the Primary DNS suffix of this computer box enter the would-be domain name. Make sure you got it right. No spelling mistakes, no "oh, I thought I did it right...". Although the domain name CAN be changed after the computer has been promoted to Domain Controller, this is not a procedure that one should consider lightly, especially because on the possible consequences.
3 6. Click Ok. 7. You'll get a warning window. 8. Click Ok. 9. Check your settings. See if they're correct.
4 10. Click Ok. 11. You'll get a warning window. 12. Click Ok to restart. Step 2: Configuring the computer's TCP/IP settings You must configure the would-be Domain Controller to use it's own IP address as the address of the DNS server, so it will point to itself when registering SRV records and when querying the DNS database. Configure TCP/IP 1. Click Start, point to Settings and then click Control Panel. 2. Double-click Network and Dial-up Connections. 3. Right-click Local Area Connection, and then click Properties. 4. Click Internet Protocol (TCP/IP), and then click Properties.
5 5. Assign this server a static IP address, subnet mask, and gateway address. Enter the server's IP address in the Preferred DNS server box. Note: This is true if the server itself will also be it's own DNS server. 6. Click Advanced. 7. Click the DNS Tab. 8. Select "Append primary and connection specific DNS suffixes" 9. Check "Append parent suffixes of the primary DNS suffix" 10. Check "Register this connection's addresses in DNS". If this Windows 2000/2003-based DNS server is on an intranet, it should only point to its own IP address for DNS; do not enter IP addresses for other DNS
6 servers here. If this server needs to resolve names on the Internet, it should have a forwarder configured. 11. Click OK to close the Advanced TCP/IP Settings properties. 12. Click OK to accept the changes to your TCP/IP configuration. 13. Click OK to close the Local Area Connections properties. Step 3: Configure the DNS Zone (Not mandatory, can be done via the Dcpromo process). This article assumes that you already have the DNS service installed. If this is not the case, please read Create a New DNS Server for AD. Furthermore, it is assumed that the DC will also be it's own DNS server. If that is not the case, you MUST configure another Windows 2000/2003 server as the DNS server, and if you try to run DCPROMO without doing so, you'll end up with errors and the process will fail. Creating a Standard Primary Forward Lookup Zone 1. Click Start, point to All Programs, point to Administrative Tools, and then click DNS Manager. You see two zones under your computer name: Forward Lookup Zone and Reverse Lookup Zone. 2. Right click Forward Lookup Zones and choose to add a new zone.
7 3. Click Next. The new forward lookup zone must be a primary zone so that it can accept dynamic updates. Click Primary, and then click Next. 4. The name of the zone must be the same as the name of the Active Directory domain, or be a logical DNS container for that name. For example, if the Active Directory domain is named "lab.dpetri.net", legal zone names are "lab.dpetri.net", "dpetri.net", or "net".
8 Type the name of the zone, and then click Next. 5. Accept the default name for the new zone file. Click Next. 6. To be able to accept dynamic updates to this new zone, click "Allow both nonsecure and secure dynamic updates". Click Next. 7. Click Finish.
9 You should now make sure your computer can register itself in the new zone. Go to the Command Prompt (CMD) and run "ipconfig /registerdns" (no quotes, duh...). Go back to the DNS console, open the new zone and refresh it (F5). Notice that the computer should by now be listed as an A Record in the right pane. If it's not there try to reboot (although if it's not there a reboot won't do much good). Check the spelling on your zone and compare it to the suffix you created in step 1. Check your IP settings. Enable DNS Forwarding for Internet connections (Not mandatory) 1. Start the DNS Management Console. 2. Right click the DNS Server object for your server in the left pane of the console, and click Properties.
10 3. Click the Forwarders tab. 4. In the IP address box enter the IP address of the DNS servers you want to forward queries to - typically the DNS server of your ISP. You can also move them up or down. The one that is highest in the list gets the first try, and if it does not respond within a given time limit - the query will be forwarded to the next server in the list. 5. Click OK. Creating a Standard Primary Reverse Lookup Zone
11 You can (but you don't have to) also create a reverse lookup zone on your DNS server. The zone's name will be the same as your TCP/IP Network ID. For example, if your IP address is , then the zone's name will be (DNS will append a long name to it, don't worry about it). You should also configure the new zone to accept dynamic updates. I guess you can do it on your own by now, can't you? Step 4: Running DCPROMO After completing all the previous steps (remember you didn't have to do them) and after double checking your requirements you should now run Dcpromo.exe from the Run command. 1. Click Start, point to Run and type "dcpromo". 2. The wizard windows will appear. Click Next. 3. In the Operating System Compatibility windows read the requirements for the domain's clients and if you like what you see - press Next.
12 4. Choose Domain Controller for a new domain and click Next. 5. Choose Create a new Domain in a new forest and click Next.
13 6. Enter the full DNS name of the new domain, for example - kuku.co.il - this must be the same as the DNS zone you've created in step 3, and the same as the computer name suffix you've created in step 1. Click Next. This step might take some time because the computer is searching for the DNS server and checking to see if any naming conflicts exist. 7. Accept the the down-level NetBIOS domain name, in this case it's KUKU. Click Next
14 8. Accept the Database and Log file location dialog box (unless you want to change them of course). The location of the files is by default %systemroot%\ntds, and you should not change it unless you have performance issues in mind. Click Next. 9. Accept the Sysvol folder location dialog box (unless you want to change it of course). The location of the files is by default %systemroot%\sysvol, and you should not change it unless you have performance issues in mind. This folder must be on an NTFS v5.0 partition. This folder will hold all the GPO and scripts you'll create, and will be replicated to all other Domain Controllers. Click Next.
15 10. If your DNS server, zone and/or computer name suffix were not configured correctly you will get the following warning: This means the Dcpromo wizard could not contact the DNS server, or it did contact it but could not find a zone with the name of the future domain. You should check your settings. Go back to steps 1, 2 and 3. Click Ok. You have an option to let Dcpromo do the configuration for you. If you want, Dcpromo can install the DNS service, create the appropriate zone, configure it to accept dynamic updates, and configure the TCP/IP settings for the DNS server IP address. To let Dcpromo do the work for you, select "Install and configure the DNS server...".
16 Click Next. Otherwise, you can accept the default choice and then quit Dcpromo and check steps If your DNS settings were right, you'll get a confirmation window. Just click Next. 12. Accept the Permissions compatible only with Windows 2000 or Windows Server 2003 settings, unless you have legacy apps running on Pre-W2K servers. 13. Enter the Restore Mode administrator's password. In Windows Server 2003 this password can be later changed via NTDSUTIL. Click Next.
17 14. Review your settings and if you like what you see - Click Next. 15. See the wizard going through the various stages of installing AD. Whatever you do - NEVER click Cancel!!! You'll wreck your computer if you do. If you see you made a mistake and want to undo it, you'd better let the wizard finish and then run it again to undo the AD.
18 16. If all went well you'll see the final confirmation window. Click Finish. 17. You must reboot in order for the AD to function properly. 18. Click Restart now. Step 5: Checking the AD installation You should now check to see if the AD installation went well.
19 1. First, see that the Administrative Tools folder has all the AD management tools installed. 2. Run Active Directory Users and Computers (or type "dsa.msc" from the Run command). See that all OUs and Containers are there.
20 3. Run Active Directory Sites and Services. See that you have a site named Default-First-Site-Name, and that in it your server is listed. 4. Open the DNS console. See that you have a zone with the same name as your AD domain (the one you've just created, remember? Duh...). See that within it you have the 4 SRV record folders. They must exist.
21 = Good If they don't (like in the following screenshot), your AD functions will be broken (a good sign of that is the long time it took you to log on. The "Preparing Network Connections" windows will sit on the screen for many moments, and even when you do log on many AD operations will give you errors when trying to perform them). If they don't (like in the following screenshot), your AD functions will be broken (a good sign of that is the long time it took you to log on. The "Preparing Network Connections" windows will sit on the screen for many moments, and even when you do log on many AD operations will give you errors when trying to perform them).
22 = Bad This might happen if you did not manually configure your DNS server and let the DCPROMO process do it for you. Another reason for the lack of SRV records (and of all other records for that matter) is the fact that you DID configure the DNS server manually, but you made a mistake, either with the computer suffix name or with the IP address of the DNS server (see steps 1 through 3). To try and fix the problems first see if the zone is configured to accept dynamic updates. 1. Right-click the zone you created, and then click Properties.
23 2. On the General tab, under Dynamic Update, click to select "Nonsecure and secure" from the drop-down list, and then click OK to accept the change. You should now restart the NETLOGON service to force the SRV registration. You can do it from the Services console in Administrative tools:
24 Or from the command prompt type "net stop netlogon", and after it finishes, type "net start netlogon". Let it finish, go back to the DNS console, click your zone and refresh it (F5). If all is ok you'll now see the 4 SRV record folders. If the 4 SRV records are still not present double check the spelling of the zone in the DNS server. It should be exactly the same as the AD Domain name. Also check the computer's suffix (see step 1). You won't be able to change the computer's suffix after the AD is installed, but if you have a spelling mistake you'd be better off by removing the AD now, before you have any users, groups and other objects in place, and then after repairing the mistake - re-running DCPROMO.
25 5. Check the NTDS folder for the presence of the required files. 6. Check the SYSVOL folder for the presence of the required subfolders. 7. Check to see if you have the SYSVOL and NETLOGON shares, and their location.
26 If all of the above is ok, I think it's safe to say that your AD is properly installed.
How to Install Active Directory on Server 2003 Table of Content HOW DO I INSTALL ACTIVE DIRECTORY ON MY WINDOWS SERVER 2003 SERVER?... 2 STEP 1: CONFIGURE THE COMPUTER'S SUFFIX... 3 STEP 2: CONFIGURING
Installation of MicroSoft Active Directory Before you start following this article you must be aware this is simply a lab setup and you need to assign relevant ip address, hostnames & domain names which
Installing the Active Directory Domain Services Role Press the Ctrl-Alt-Del on the xxrwdc computer. Log in as the default administrator of the local computer with the username Administrator and cisisthebest!
Course: WIN310 Student Lab Setup Guide Microsoft Windows Server 2003 Network Infrastructure (70-291) ISBN: 0-470-06887-6 STUDENT COMPUTER SETUP Hardware Requirements All hardware must be on the Microsoft
Page 1 of 6 How to install Small Business Server 2003 in an existing Active Directory domain INTRODUCTION This article describes how to install a Microsoft Windows Small Business Server (SBS) 2003-based
Course: WIN310 Student Lab Setup Guide Summer 2010 Microsoft Windows Server 2003 Network Infrastructure (70-291) ISBN: 0-470-06887-6 Published by Wiley & Sons 1 STUDENT COMPUTER SETUP Hardware Requirements
How to Install the Active Directory Domain Services (AD DS) Role in Windows Server 2008 R2 and Promote a Server to a Domain Controller I am not responsible for your actions or their outcomes, in any way,
Network System Management Creating an Active Directory Domain Objectives Identify the procedures involved in the promotion of a stand-alone Windows Server to an active directory services (ADS) domain controller
Installing Active Directory 119 Installing Active Directory Installing Active Directory is an easy and straightforward process as long as you planned adequately and made the necessary decisions beforehand.
Setting up Active Directory Domain Services Tom Brett CREATING A SINGLE DOMAIN FOREST Once you have Windows Server 2008 R2 installed, it s pretty easy to create a domain you simply run the domain controller
If you have set up a domain controller previously with Windows 2000 Server, or Windows Server 2003, then you would be familiar with the dcpromo.exe command also be used to set up a Domain Controller on
Requirements:! A computer dedicated to FTP server only! Linksys router! TCP/IP internet connection Steps: Getting Started Configure Static IP on the FTP Server Computer: Setting Up Your FTP Server 1. This
Chapter 3: Building Your Active Directory Structure Page 1 of 46 Chapter 3: Building Your Active Directory Structure Objectives Now that you have had an introduction to the concepts of Active Directory
Islamic University of Gaza College of Engineering Computer Department Computer Networks Lab Introduction to Administering Accounts and Resources Prepared By: Eng.Ola M. Abd El-Latif Mar. /2010 0 :D Objectives
JWCL031_appB_467-475.indd Page 467 5/12/08 11:02:46 PM user-s158 Appendix B Lab Setup Guide The Windows Server 2008 Applications Infrastructure Configuration title of the Microsoft Official Academic Course
UNIT 5 ADDITIONAL PROJECTS BEFORE YOU BEGIN The RODC must be configured to use the RWDC as its Preferred DNS Server. Active Directory is installed on the RWDC. The RODC must be a member server within the
Training Installing and Setting up Microsoft DNS Server Introduction Versions Used Windows Server 2003 Setup Used i. Server Name = martini ii. Credentials: User = Administrator, Password = password iii.
Windows 2003 Server Consolidated Lab 1 Nov 20, 2009 Name: In the following lab you are asked to complete several tasks you have previously completed to set up a Windows 2003 Server. Instead of using Server
istorage Server: High-Availability iscsi SAN for Windows Server 2008 & Hyper-V Clustering Tuesday, Feb 21 st, 2012 KernSafe Technologies, Inc. www.kernsafe.com Copyright KernSafe Technologies 2006-2012.
5 Configuring a DNS Infrastructure Exam Objectives in this Chapter: Configure a DNS server. Configure DNS zone options. Configure DNS forwarding. Manage DNS zone settings. Manage DNS server options. Why
Setting Up a Backup Domain Controller June 27, 2012 Copyright 2012 by World Class CAD, LLC. All Rights Reserved. A Backup Domain Controller After setting up a primary domain controller, we will want to
Step-by-Step Guide for Setting Up IPv6 in a Test Lab Microsoft Corporation Published: July, 2006 Author: Microsoft Corporation Abstract This guide describes how to configure Internet Protocol version 6
istorage Server: High Availability iscsi SAN for Windows Server 2012 Cluster Tuesday, December 26, 2013 KernSafe Technologies, Inc www.kernsafe.com Copyright KernSafe Technologies 2006-2013.All right reserved.
Active Directory integration with CloudByte ElastiStor Prerequisite Change the time and the time zone of the Active Directory Server to the VSM time and time zone. Enabling Active Directory at VSM level
AD RMS Step-by-Step Guide Microsoft Corporation Published: March 2008 Author: Brian Lich Editor: Carolyn Eller Abstract This step-by-step guide provides instructions for setting up a test environment to
Article ID: 216498 - Last Review: September 11, 2011 - Revision: 12.0 How to remove data in Active Directory after an unsuccessful domain controller demotion System Tip This article applies to a different
Endpoint Client Installation using Group Policy (Logon Script): Table of Contents Introduction... 2 Creating a Batch File... 2 Logon Script Permissions... 3 Assigning the Logon Script to User(s)... 3 Domain
Windows 2003 Server Installation Guide Revision 2.0 April 14, 2011 Licenses This manual is the exclusive property of Prometric, Inc. This manual is licensed for use with restrictions to authorized centers
COURSE FILE (COURSE PLAN) Year : 2012-13 Sem: ODD Faculty Details Name of the Faculty : Mullai.P & Yaashuwanth.C Designation : Assistant Professor ( OG. ),Assistant Professor (OG) Department : Information
Installing Windows Rights Management Services with Service Pack 2 Step-by- Step Guide Microsoft Corporation Published: October 2006 Author: Brian Lich Editor: Carolyn Eller Abstract This step-by-step guide
This excerpt is taken from book Installing and Configuring SharePoint 2010 2 nd Edition. You can download this FREE ebook from the following link: http://walisystemsinc.com/installing_and_configuring_sharepoint2010_2nd_ed.php
Microsoft Virtual Labs Active Directory New User Interface 2 Active Directory New User Interface Table of Contents Active Directory New User Interface... 3 Exercise 1 User Management and Saved Queries...4
Joining a Domain in Windows XP Pro Table of Content HOW DO I CHANGE A COMPUTER'S DESCRIPTION, NAME, OR JOIN A DOMAIN IN WINDOWS XP PRO?... 1 TO ADD A COMPUTER DESCRIPTION... 1 TO CHANGE A COMPUTER NAME...
How To Use 802.1x EAP-TLS or PEAP-MS-CHAP v2 with Microsoft Windows Server 2003 to Make a Secure Network Introduction This document describes how to create a secure LAN, using two servers and an 802.1xcompatible
L.A. Bridge Win95 Dialup Page: 1 System Requirements Dialing up with Windows 95 These instructions will work with most Windows 95 compatible computers, using the Microsoft dialer software. Most versions
How to Remotely View Security Cameras Using the Internet Introduction: The ability to remotely view security cameras is one of the most useful features of your EZWatch Pro system. It provides the ability
Article ID: 216498 - Last Review: February 3, 2010 - Revision: 11.0 How to remove data in Active Directory after an unsuccessful domain controller demotion System Tip This article applies to a different
Página 1 de 54 Step-by-Step Guide for Setting Up VPN-based Remote Access in a Test Lab This guide provides detailed information about how you can use five computers to create a test lab with which to configure
Windows Domain Network Configuration Guide Windows Domain Network Configuration Guide for CCC Pathways Copyright 2008 by CCC Information Services Inc. All rights reserved. No part of this publication may
Step By Step Guide: Demonstrate DirectAccess in a Test Lab Microsoft Corporation Published: May 2009 Updated: October 2009 Abstract DirectAccess is a new feature in the Windows 7 and Windows Server 2008
Omni 56K USB Lite Quick Start Guide ZyXEL TOTAL INTERNET ACCESS SOLUTION 1. Hardware Installation Connect your modem to your analog phone or fax. Use the phone cord included to connect to the phone jack
c623242f-20f0-40fe-b5c1-8412a094fdc7 Deploying Personal Virtual Desktops by Using RemoteApp and Desktop Connection Step-by-Step Guide Microsoft Corporation Published: June 2009 Updated: April 2010 Abstract
How to Edit Local Computer Policy Settings To edit the local computer policy settings, you must be a local computer administrator or a member of the Domain Admins or Enterprise Admins groups. 1. Add the
Deploying Remote Desktop IP Virtualization Step-by-Step Guide Microsoft Corporation Updated: April 2010 Published: July 2009 Abstract Remote Desktop IP Virtualization provides administrators the ability
Hack DNS for lightning-fast Web browsing Preston Gralla May 23, 2007 (Computerworld) No matter how big the broadband pipe you use to surf the Web, it's not big enough. Everyone, whether they use a slowpoke
Step-by-Step Guide for Creating and Testing Connection Manager Profiles in a Test Lab Microsoft Corporation Published: May, 2005 Author: Microsoft Corporation Abstract This guide describes how to create
Installing the Microsoft Network Driver Interface Overview This guide explains how to install the PictureTel Live200 Microsoft Network Driver Interface (NDIS) software you have downloaded from PictureTel's
Overview: All of the quotation marks in here are being used to actually quote a phrase or value. Don't actually use them in any names during any of the stages as you may break something. The basic requirements
Migrating Active Directory to Windows Server 2012 R2 Windows Server 2012 R2 Hands-on lab In this lab, you will complete a migration of a Windows Server 2008 R2 domain environment to Windows Server 2012
NAS 206 Using NAS with Windows Active Directory Connect your NAS to a Windows Active Directory domain A S U S T O R C O L L E G E COURSE OBJECTIVES Upon completion of this course you should be able to:
Contents AD RMS Windows Server 2008 to Windows Server 2008 R2 Migration and Upgrade Guide... 2 About this guide... 2 Preparing for the migration or upgrade of an AD RMS cluster... 2 Checklist: Preparing
Introduction ExchangeDefender Compliance Archive provides secure, long term storage, recovery and ediscovery system that assures compliance with regulatory requirements established by IRS, HIPAA, SOX and
Using Logon Agent for Transparent User Identification Websense Logon Agent (also called Authentication Server) identifies users in real time, as they log on to domains. Logon Agent works with the Websense
Information Services Accessing the University Network using a Virtual Private Network Connection (VPN), with Windows XP Professional Amendment & Authorisation History Ver Date Changes Name Author A 29/3/05
ILTA 2013 - HAND 6B Upgrading and Deploying Windows Server 2012 In the Legal Environment Table of Contents Purpose of This Lab... 3 Lab Environment... 3 Presenter... 3 Exercise 1 Add Roles and Features...
Information Security Practice II Installation and set-up of Web Server and FTP accounts Installation of IIS Setup of laboratory 3 virtual machines are required in this laboratory: 1. Win2003 the web server
Active Directory Infrastructure Design Document Written By Sainath KEV Microsoft MVP Directory Services Microsoft Author TechNet Magazine, Microsoft Operations Framework Microsoft Speaker - Singapore Document
SETTING UP ACTIVE DIRECTORY (AD) ON WINDOWS 2008 FOR DOCUMENTUM @ EROOM Abstract This paper explains how to setup Active directory service on windows server 2008.This guide also explains about how to install
Appendix C Preparing Your Network This appendix describes how to prepare your network to connect to the Internet through the FVX538 ProSafe VPN Firewall 200 and how to verify the readiness of broadband
Prestige 314 Read Me First Console WAN 10M PORT Prestige Rear Panel Connections CONNECTION Use an RS-232 console cable. Use the cable that came with your broadband modem. LAN 10/100M Port Number COMPUTER
Trial environment setup Exchange Server Archiver - 3.0 Introduction This document describes how you can set up a trial environment for using Exchange Server Archiver with Exchange Server 2007. You do not
Configuring Outlook for Windows to use your Exchange email McGill faculty, staff and students are given a Microsoft Exchange account which will give you an email box, calendaring features, access to McGill
How to Remotely View Security Cameras Using the Internet Introduction: The ability to remotely view security cameras is one of the most useful features of your EZWatch Pro system. It provides the ability
1. Set Daylight Savings Time... 3 a. Have client log into Novell/Local Machine with Administrator Account...3 b. Access Adjust Date/Time...3 c. Make sure the time zone is set to Central Time...3 2. Create
4 Port 10/100M Internet Broadband Router with USB Printer server Quick Installation Guide #4824904AXZZ0 1. Hardware Installation A. System Requirement Before you getting started, make sure that you meet
StarWind iscsi SAN Software: Using StarWind with MS Cluster on Windows Server 2003 www.starwindsoftware.com Copyright 2008-2011. All rights reserved. COPYRIGHT Copyright 2008-2011. All rights reserved.
Basic Exchange Setup Guide The following document and screenshots are provided for a single Microsoft Exchange Small Business Server 2003 or Exchange Server 2007 setup. These instructions are not provided
Wireless G Broadband Router quick install guide Model 503693 INT-503693-QIG-0608-02 Thank you for purchasing the INTELLINET NETWORK SOLUTIONS Wireless G Broadband Router, Model 503693. This quick install
WatchGuard Mobile User VPN Guide Mobile User VPN establishes a secure connection between an unsecured remote host and a protected network over an unsecured network using Internet Protocol Security (IPSec).
Active Directory Restoration This document outlines the steps required to recover an Active Directory Infrastructure, running on Windows 2003 R2 Server Standard. The scope of this document covers the scenario
Customizing Remote Desktop Web Access by Using Windows SharePoint Services Stepby-Step Guide Microsoft Corporation Published: July 2009 Updated: September 2009 Abstract Remote Desktop Web Access (RD Web
PC/POLL SYSTEMS Version 7 Polling SPS2000 Cash Register TCP/IP Communications PC/POLL SYSTEMS supports native TCP/IP polling for the SPS2000 cash register. It is recommended users have the register updated
Using FileZilla FTP Server with a DT80 Series Logger File Transfer Protocol (FTP) is used by the datataker DT80 range data loggers when pushing data to a file server. This server could be located remotely
How the Active Directory Installation Wizard Works - Directory Services: Windows Serv... Page 1 of 18 How the Active Directory Installation Wizard Works In this section Active Directory Installation Wizard
Getting Started with Hyper-V and the Scale Computing Cluster Scale Computing 5225 Exploration Drive Indianapolis, IN, 46241 Contents Contents CHAPTER 1 Introduction to Hyper-V: BEFORE YOU START. vii Revision
Clustering VirtualCenter 2.5 Using Microsoft Cluster Services This paper documents the steps to successfully implement a high availability solution for VirtualCenter 2.5 using Microsoft s cluster services.
Contents 1. Introduction... 3 1.1. Setup... 3 2. Introduction to Active Directory Services... 4 3. Installing and Configuring Active Directory Services... 5 3.1. Joining to Domain... 5 3.2. Promoting Member
EOS Step-by-Step Setup Guide Wireless File Transmitter FTP Mode Ad Hoc Setup Windows XP 2012 Canon U.S.A., Inc. All Rights Reserved. Reproduction in whole or in part without permission is prohibited. 1
ilaw Installation Procedure This guide will provide a reference for a full installation of ilaw Case Management Software. Contents ilaw Overview How ilaw works Installing ilaw Server on a PC Installing
Active Directory Installation on Windows Server 2012 What really active directory is..? Active Directory Domain Services (AD DS) is an extensible and scalable directory service you can use to efficiently
Notes: STATISTICA VERSION 9 STATISTICA ENTERPRISE INSTALLATION INSTRUCTIONS FOR USE WITH TERMINAL SERVER 1. These instructions focus on installation on Windows Terminal Server (WTS), but are applicable
1. Installing DNS on Windows Server 2003: If using the new style Start menu: Click on "Start", "Control Panel", "Add or Remove Programs" and select the "Add/Remove Windows Components" tab on the left-hand
Prestige 650R-31/33 Read Me First Prestige Rear Panel Connections PORT DSL CONSOLE LAN 10/100M POWER Connect to a telephone jack using a telephone wire. CONNECTION Connect to a serial port (COM port) on