Thermostat Wire Adapter

Transcription

1 elcome To ire Adapter INSTALLATION UIDE

2 INTRODUTION Thanks for purchasing the idevices ire Adapter. This easy-to-follow guide will take you through the installation process, step by step. If at any time you require assistance, please contact our ustomer Experience Team. all: Visit: Monday Friday 8am 8pm EST idevicesinc.com/support Please visit: idevicesinc.com/ompatibility to see if your HVA system is compatible. PLEASE READ PRIOR TO INSTALLIN OUR idevies THERMOSTAT IRE ADAPTER The installation of the idevices ire Adapter and all wiring must conform to local and national electrical codes. Improper wiring or installation may cause damage to this product, your, your HVA system, or your home, and could result in personal injury. The idevices ire Adapter is intended to share two signals over one wire, so that you can add a wire to a system that doesn t currently have one. our system will need at least 3 physical wires between the HVA control board and the, as well as an accessible 2 /ommon terminal on the HVA control board or transformer to connect to. The ire Adapter can also be used to add a wire other than. This can be helpful if, for example, you wish to add air conditioning to a heat only system, fix a broken wire that is inaccessible, or upgrade a one stage furnace to a two-stage furnace. e recommend you contact an HVA professional to discuss these options. ETTIN STARTED The idevices ire Adapter should be installed in or near the HVA system control board or furnace, or another dry, indoor location. Find a location with easy access to the wires that run between the HVA unit and the If needed, you can use two #8 screws (not included) to mount the wire adapter to a convenient surface ire Adapter idth: 3.30 Height: 2.05 Depth: 0.98 Mounting Hole idth: 0.17 Height: 0.62 Separate the front cover from the wire adapter by squeezing the four tabs (two on either side) 3

3 IRIN REQUIREMENTS Acceptable ire: 24-18A physical wires, or damage to the system or, or unintended/undesirable system operation may result. Max. ire length (total wire length between HVA system and ): 18 A: 195 feet 24 A: 65 feet All wires and connections should conform to applicable local and national electrical codes. OMMON IRIN DIARAMS: 1. onventional (Heat + A) 4 ires 2. onventional (Heat + A) 5 ires 3. onventional (Heat + Fan) Page: 6 Page: 8 Page: 10 ELETRIAL SPEIFIATIONS RATED INPUT: Voltage: 18 to 30VA, 50Hz or 60Hz urrent consumption: 30mA at 24VA when & are connected Terminals: R,,,,, RATED OUTPUT: Voltage: 18 to 30VA, 50Hz or 60Hz lass 2 urrent rate: 5 Amps 4. onventional (A + Fan) 5. Heat Pump System Page: 12 Page: 14 If your system doesn t match one of these configurations, please contact our ustomer Experience team. all: Visit: Monday Friday 8am 8pm EST [email protected] idevicesinc.com/support Terminals: R,,,,, ARNIN: TURN THE POER TO OUR HVA SSTEM AND OLD THERMOSTAT OFF BEFORE OU START THE INSTALLATION PROESS! Note: The ire Adapter should not be used to share either the R (or R/) wire or the wire. Both the R wire for the system and the wire must each be separate, 4 5

4 1. ONVENTIONAL (HEAT + A) 4 IRES ire Adapter. Leave the in place between -. all ire Adapter HVA 4. onnect the last remaining wire (that comes from the ) to the terminal on the STAT side of the ire Adapter. 5. ap or tape the ends of any unused wires. R / AT THE FURNAE OR HVA SSTEM: R R 1. onnect the R,,,, and terminals on the EQUIP side of the ire Adapter to the corresponding terminals on the HVA control board. Use the provided length of wire if necessary. 2. onnect the existing R and wires (that come from the ) to the R and terminals on the STAT side of the ire Adapter. Leave the in place between R-. Note: If the system does not have a wire, do not connect any of the terminals. 3. onnect one of the remaining two wires (that come from the ) to the terminal on the STAT side of the R 6 be routed around the wire adapter, directly from the HVA system to the 1. onnect the R and wires coming from the wall to the R and terminals on the Leave the in place between R-. Note: If the system does not have a wire, do not connect anything to the terminal. insert it into the screw clamp on the, and tighten the screw. onnect the leg of the Signal Splitter to the terminal of the, and the leg of the to the terminal of the 3. onnect the wire you selected in step 4 above to the 7

5 2. ONVENTIONAL (HEAT + A) 5 IRES ire Adapter. Leave the in place between -. all ire Adapter HVA 4. onnect the last remaining wire (that comes from the ) to the terminal on the STAT side of the ire Adapter. 5. ap or tape the ends of any unused wires. / be routed around the wire adapter, directly from the HVA system to the R R R R 1. onnect the R,, and wires coming from the wall to the R,, and terminals on the Remove the between R-. Note: If the system does not have a wire, do not connect anything to the terminal. AT THE FURNAE OR HVA SSTEM: 1. onnect the R,,,,, and terminals on the EQUIP side of the ire Adapter to the corresponding terminals on the HVA control board. Use the provided length of wire if necessary. 2. onnect the existing R,, and wires (that come from the ) to the R,, and terminals on the STAT side of the ire Adapter. Remove the between R-. Note: If the system does not have a wire, do not connect any of the terminals. insert it into the screw clamp on the, and tighten the screw. onnect the leg of the Signal Splitter to the terminal of the, and the leg of the to the terminal of the 3. onnect the wire you selected in step 4 above to the 3. onnect one of the remaining two wires (that come from the ) to the terminal on the STAT side of the 8 9

6 3. ONVENTIONAL (HEAT + FAN) the ire Adapter. Leave the in place between -. all ire Adapter HVA 4. onnect the last remaining wire (that comes from the ) to the terminal on the STAT side of the ire Adapter. be routed around the wire adapter, directly from the HVA system to the R / AT THE FURNAE OR HVA SSTEM: R R R 1. onnect the R,, and terminals on the EQUIP side of the ire Adapter to the corresponding terminals on the HVA control board. onnect the terminal on the HVA board to the terminal on the ire Adapter. Use the provided length of wire if necessary. 2. onnect the existing R wire (that comes from the ) to the terminal on the STAT side of the ire Adapter. Leave the in place between R-. 3. onnect one of the remaining two wires (that come from the ) to the terminal on the STAT side of onnect the R and wires coming from the wall to the and terminals on the Leave the in place between R-. insert it into the screw clamp on the, and tighten the screw. onnect the leg of the Signal Splitter to the terminal of the, and the leg of the to the terminal of the 3. onnect the wire you selected in step 4 above to the 11

7 4. ONVENTIONAL (A + FAN) ire Adapter. Leave the in place between -. all ire Adapter HVA 4. onnect the last remaining wire (that comes from the ) to the terminal on the STAT side of the ire Adapter. be routed around the wire adapter, directly from the HVA system to the R / AT THE FURNAE OR HVA SSTEM: R R R 1. onnect the R,, and terminals on the EQUIP side of the ire Adapter to the corresponding terminals on the HVA control board. onnect the terminal on the HVA board to the terminal on the ire Adapter. Use the provided length of wire if necessary. 2. onnect the existing R wire (that comes from the ) to the R terminal on the STAT side of the ire Adapter. Leave the in place between R-. 3. onnect one of the remaining two wires (that come from the ) to the terminal on the STAT side of the onnect the R and wires coming from the wall to the and terminals on the Leave the in place between R-. insert it into the screw clamp on the, and tighten the screw. onnect the leg of the Signal Splitter to the terminal of the, and the leg of the to the terminal of the 3. onnect the wire you selected in step 4 above to the 13

8 5. HEAT PUMP SSTEM all ire Adapter HVA 3. onnect one of the remaining two wires (that come from the ) to the terminal on the STAT side of the ire Adapter. Leave the in place between onnect the last remaining wire (that comes from the ) to the terminal on the STAT side of the ire Adapter. 5. ap or tape the ends of any unused wires. O/B / O/B be routed around the wire adapter, directly from the HVA system to the R R R R 1. onnect the R and wires coming from the wall to the R and terminals on the Leave the in place between R-. Note: If the system does not have a wire, do not connect anything to the terminal. AT THE FURNAE OR HVA SSTEM: 1. onnect the R,,, and terminals on the EQUIP side of the ire Adapter to the corresponding terminals on the HVA control board. onnect the O/B (or O, or B) wire on the HVA control board to the terminal of the ire Adapter. Use the provided length of wire if necessary. 2. onnect the existing R and wires (that come from the ) to the R and terminals on the STAT side of the ire Adapter. Leave the in place between R-. Note: If the system does not have a wire, do not connect any of the terminals. 14 insert it into the screw clamp on the, and tighten the screw. onnect the leg of the Signal Splitter to the O/B terminal of the, and the leg of the to the terminal of the 3. onnect the wire you selected in step 4 above to the 15

9