e explosion-proof emergency light fittings battery sets for zone 1/21 and zone 2/22 e 187/ nd 187/188...

Transcription

1 SCHUCH Explosion - proof Light Fittings SCHUCH Dust- / Waterproof Light Fittings e explosion-proof emergency light fittings with individual battery sets for zone 1/21 and zone 2/22 e 187/ nd 187/ explosion-proof sheet steel ligh fittings for extremly dust hazarous areas of zones 1/21 and 2/22 nd 191/ extremly low profile design for ceiling or recessed mounting zones 2/22 nd explosion-proof compact sheet steel light fittings for zone 2 and 22 with new central locking system 161/ dust/waterproof polyester light fittings with diffuser, insulation class II Contents Description Series Page Explosion-proof Light Fittings for ZONE 1/21 polyester type polyester pole-mount type polyester emergency type low profile type for ceiling and recessed installation tapered sheet steel type... for high ambient temperatures... for carbon disulphide T6... for dust hazardous areas... for high ambient temperatures compact sheet steel type... for induction-type lamps bulkhead type suspended type floodlights handlamp emergency and sign type mine gas-proof fittings... for induction-type lamps Explosion-proof Light Fittings for ZONE 2/22 polyester type... shock proof type... emergency and sign type low profile type for ceiling and recessed installation tapered sheet steel type... for dust hazardous areas compact sheet steel type... for high ambient temp.... for induction-type lamps floodlights e e 152 PM 5 e e e e e e 181/182 H 11 e T6 12 e e e 187/188 H.. 15 e 2070 Endura 16 e 2691/92 17 d d d e e 2694/ e e 2080 ENDURA 28 n n nd nd nd n 161/.../../. 33 n 162/.../../. 33 nd 161/.../../. 34 nd 162/.../../. 34 n nd nd nd nd nd nd nd nd 3084 H60 43 nd 3084 Endura 43 nd 2070 Endura 44 nd n n nd nd Explosion-proof Installation Material carrier rail system wall sockets plugs couplers switches junction boxes TRS e Dust/Waterproof Light Fittings polyester type insulation class II 161/ emergency and sign type 161/162/.../../. 60 Emergency Light Power Supply Unit N12 62 Technical Supplement Please observe the notes in the technical supplement 119e/1

2 Explosion-proof Light Fittings Series e Hazardous areas of zones 1, 21 and 2, 22 as standard illumination or as emergency illumination in combination with power supply units. Housing: Glass fibre reinforced polyester resin. Cover: Clear polycarbonate with internal prisms, hingeable. Reflector: Glass fibre reinforced polyester, hingeable. Central locking system: Triangular key M6. Isolating switch: Switching off all poles when the light fitting is opened. Optical indicator showing the actual position of the switch. Wiring: Double channel ballast with end-of-life switching-off system. Connection terminals: Standard: L1+N+PE; up to 6.0 mm². Through wiring system: Looping the mains cable at one end of the housing or up to 5x2,5mm² at extra charge. Cable entries: 3 entries M25 x 1,5 (2 glands: 1 plugged + 1 blind plug). Mounting: Horizontal Mechanical installation: 2 suspension hooks (H8V) or 2 ceiling brackets (15A), see accessories. Schuch Quality - your advantage: Suspension hooks H8V Ceiling brackets 15A sturdy design of high chemical resistance for application in rough industrial conditions: - housing from glass fibre reinforced polyester (impact resistance: 20Nm = triple safety) - polycarbonate diffuser of high impact strength (equal wall thickness: 2,5mm) - solid central locking system made from galvanized steel and high-grade stainless steel hinges - highly resistant EPDM gasket of dimensional stability that stands for a permanently safe tightness to water and dust reliable, fail-safe and long-life thanks to a special ex-proof ECG with high grade quality features: - "end-of-life swiching-off system" i.e. at the end of its life a fluorescent tube is safely switched off (world novelty acc. to the latest IEC standards IEC ) - in compliance with the requirements of over voltage category III (standard = over voltage category II) - widened interference suppression up to 300MHz (standard = 30MHz) - double channel system with separate lamp monitoring - extremely favourable operating temperatures thanks to a special quartz sand encapsulation of ballast inside an aluminium housing are a guarantee for a long life and an application at an ambient temperature of + 60 C wide range of application and flexibility at most different environmental conditions: - certification for installation in gas and dust atmospheres (zones 1 and 21) - application up to temperature class T6 (series e T6) - wide range of admissible ambient temperature from -20 C to +60 C (worldwide first certification) +60 C - designed for application of fluo tubes of 26mm Ø, 38mm Ø and of longlife 0 C tubes - classical bilateral through wiring system or looping system on one side of the housing - shockproof and certified for application in civil defence buildings (RK 1.6 / 16A) excellent light distribution and glare limitation thanks to a light technically optimized prismatic diffuser e152.. for bi-pin fluorescent tubes, socket G13 II 2 G EEx edq IIC T4 II 2 D T80 C IP66 EC Test Certificate: PTB 97 ATEX 2223, 2224, 2225 Ignition protection: e (increased safety) Explosion protection: II 2 G EEx edq IIC T4 (Zone 1) II 2 D T80 C (Zone 21) e152 21/22/41/42: -20 C up to +60 C e152 61/62: -20 C up to +50 C Rated voltage: V AC/DC, Frequency: 0 or 50-60Hz Looping the cable on one side: All light fittings of series e152.. have got 2 cable entries on one small side of the housing for cable looping instead of the through wiring system. T 26 T 38 e Temp. Lamps/ weight class Watts appr.kg 1) with electronic ballast (EVG) e T4 1 x T 26/18 W 6,7 e T4 2 x T 26/18 W 6,8 e T4 1 x T 26/36 W 10,0 e T4 2 x T 26/36 W 10,1 e T4 1 x T 26/58 W 12,2 e T4 2 x T 26/58 W 12,4 1) Weights without packing material 119e/2 Please observe the notes in the technical supplement

3 e 152 T6 Carbon disulphide - temperature class T6 II 2 G EEx edq IIC T6 II 2 D T80 C IP66 Hazardous areas of zones 1, 21 and 2, 22 with gases and vapours of temperature class T6 (carbon disulphide). As above but with bi-pin fluorescent tubes of 38mm Ø. EC Test Certificate, ignition protection, explosion protection and rated voltage same as for e C up to +40 C e T6 T 38 Temp. Lamps/ Weight class Watts appr.kg 1) with electronic ballast e T T6 1 x T 38/20 W 6,7 e T T6 2 x T 38/20 W 6,8 1) Weights without packing material Photo: BASF e152 ZB II 2 G EEx edq IIC T4 for connection to central or group battery systems II 2 D T80 C IP66 Emergency light fittings energized by central- or group battery systems in hazardous areas of zones 1,21 and 2,22. Same as type e152 but with DC-detection and change-over to 1-lamp operation (emergency mode)). T 26 T 38 Temp. Lamps/ Weight class Watts appr.kg 1) with electronic ballast in special version e ZB e ZB T4 2 x T 38/18 W 6,8 e ZB T4 2 x T 38/36 W 10,1 e ZB T4 2 x T 38/58 W 12,4 1) Weights without packing material Further Series / Equipment with 4 cable entries max. with different cable glands with through wiring system with 2 individual electronic ballasts without switch (series e152.. OS) with 2 individual electronic ballasts and monitoring device for individual monitoring the light fittings connected to a central or group battery system with mirror-type reflector for high rooms pole mount fitting (series e152.. PM) emergency (series e148...) Please observe the notes in the technical supplement 119e/3

4 Mounting material Suspension hooks H8V P Ceiling brackets 15A P Pipe clamps RO...A P Wall brackets W26 P Wall bracket W26/45 P Further accessories as well as carrier rail systems and through wiring systems are available. Accessories / Spare Parts Spare diffusers for series e 152, e Cable glands Lamp holders e2412/1 Li e2412/2 Li e2412/1 Re e2412/2 Re Alu mirror-type reflectors, built in SP 21 SP 22 SP 41 SP 42 SP 61 SP 62 SP 21 NE SP 22 NE SP 41 NE SP 42 NE SP 61 NE SP 62 NE Mounting material H8V P A P AV P RO 112 A P RO 2 A P W 26 P W 26/30 P W 26/45 P Keys J J spare cover PC for 18 W spare cover PC for 36 W spare cover PC for 58 W ex-proof plastic cable gland M25 x 1,5 ex-proof plastic plug M25 x 1,5 ex-proof plastic cable gland with plug M25 x 1,5 1 ex-proof lampholder (left side) without support 2 ex-proof lampholders (left side) without support 1 ex-proof lampholder (right side) without support 2 ex-proof lampholders (right side) without support for 1 x 18 W for 2 x 18 W for 1 x 36 W for 2 x 36 W for 1 x 58 W for 2 x 58 W Alu mirror-type reflectors, for later installation (Polyester reflector with riveted aluminium reflector) - ambient temp.: +50 C max. for 1 x 18 W for 2 x 18 W for 1 x 36 W for 2 x 36 W for 1 x 58 W for 2 x 58 W 2 hooks with bolts, stainless steel 2 ceiling brackets, hot galvanized steel 2 ceiling brackets, stainless steel 2 pipe clamps 1 1 / 2", stainless steel, with support 2 pipe clamps 2", stainless steel, with support 2 wall mounting angles 2 wall mounting angles 30 2 wall mounting angles 45 angle key M6 universal triangular key set M5,6,8,10,12 universal triangular key set M4,5,6,8,10,12 119e/4 Please observe the notes in the technical supplement

5 Explosion-proof Light Fittings Series e PM Hazardous locations of zones 1, 2 and 21, 22. Housing: Glass fibre reinforced polyester resin. Cover: Clear polycarbonate with internal prisms, hingeable. Reflector: Glas fibre reinforced polyester resin, hingeable. Central locking system: Triangular key M6. Isolating switch: Switching off all poles when the light fitting is opened. Optical indicator showing the actual position of the switch. Wiring: Double-channel ballast with "end-of-life" switching-off system. Connection terminals: Standard: L1+N+PE; up to 6mm². Cable entry: 1 gland of size M25 x 1,5 through the pole tube. Mounting system:on poles with outreach and supporting section acc. to DIN : 18/20W: 42mmØ x 250mm 36/40W: 42mmØ x 400mm 58/60W: 42mmØ x 400mm length The features of this series of light fittings and of series e152.. are of an equal quality. Only the ambient temperatures are different. e152.. PM for bi-pin fluorescent tubes, socket G13 EC Test Certificate: PTB 97 ATEX 2223, 2224, 2225 Ignition protection: "e" (increased safety) Explosion protection: II 2 G EEx edq IIC T4 (Zone 1) II 2 D T80 C (Zone 21) II 2 G EEx edq IIC T4 II 2 D T80 C IP66 Admissible ambient temperatures: e15221/22pm -20 C up to +50 C e15241/42pm -20 C up to +50 C e15261/62pm -20 C up to +50 C Rated voltage: V AC/DC, 0 or 50 to 60 Hz T 26 e PM T 38 Temp. Lamps/ Weight class Watts appr.kg 1) with electronic ballast (EVG) e PM T4 1 x T 26/18 W 7,6 e PM T4 2 x T 26/18 W 7,7 e PM T4 1 x T 26/36 W 12,0 e PM T4 2 x T 26/36 W 12,3 e PM T4 1 x T 26/58 W 13,5 e PM T4 2 x T 26/58 W 14,0 1) Weights without packing material. Accessories and spare parts please see series e Further Series / Equipment without switch (series e152.. PM OS) Foto: BAYER Please observe the notes in the technical supplement 119e/5

6 Explosion-proof Emergency Light Fittings with Individual Battery Sets Series e148.. Safety illumination in hazardous areas of Zones 1, 2 and 21, 22. Mechanical design: Housing and battery box: Glass fibre reinforced polyester, battery box mounted to one front side of the main housing. Cover: Clear polycarbonate with internal prisms, hinged. EPDM gasket. Reflector: Glass fibre reinforced polyester, hinged. Central locking system: Operated by means of a triangular key M6 Isolating switch: Switching off all poles when the light fitting is opened. Forced optical indicator showing the actual position of the switch. Separate switch for isolating the battery. Cable entry: 2 entries M25 x 1,5 (1 of which plugged) both on the same side. Through wiring system: Standard: Looping the mains cable at one end of the housing up to 4 x 6mm 2 (6 cores optional). Optional (40W version): Internal through wiring system (4 cores min: L1+L1'+N+PE; in case of 3 phases 6 conductors L1, L1, L2, L3, N, PE). Mounting: By means of suspension hooks (H8VP) or ceiling brackets (15AP) - see accessories/spare parts. Wiring diagram (maintained operation) Light switch Emergency light fitting Start-up: Connect battery conductor Taking out of operation: Disconnect battery conductor. Lamp LP1: Lighting in mains operation and in case of a mains failure via the batteries. Lamp Lp2: Lighting in mains operation only or in case of lamp failure of Lp1 in emergency operation. Stand-by wiring: Do not connect L1' Battery conductor Electrical design: Microprocessor controlled intelligent emergency electronic device with endof-life-switch-off -system acc. to IEC Redundant low discharge protection and restart blocking system. Multi-function LED: For monitoring the emergency light function and coded indication of the status. NiCd batteries: 6 V/4 Ah or 6 V/7Ah, maintenance-free located in the battery box; quick battery replacement. Electrical disconnection whenever the polycarbonate cover or the battery box are opened. Automatic monitoring: Weekly functioning test, annual 2/3 operating period test. Recharging time: 24h, acc. to EN Mode of operation: Maintained operation: Switching over to battery operation in case of mains failure. 1 lamp for mains and emergency operation. 2nd lamp for mains operation only. In case 1 lamp fails the second lamp will take over the emergency operation. Connection terminals: Standard L1 + L1' + N + PE, max. range of connection 6mm 2 1. Direct phase L1, (or L2, L3) comes from the circuit fuse and is directly (not via the switch) connected to L1 terminal (or L2, L3) (= charging phase). Consequently if the light fitting is switched off the direct phase is live unless the fuses are open or removed. 2. Switched phase L1' (or L2', L3') goes to connection terminal L1' (or L2', L3') via the switch and must be electrically identical with the direct phase L1 (or L2, L3). 3. Neutral conductor N: In case of 220V between the outer conductors instead of the N conductor an outer conductor is selected e.g. L2 or L3. 4. Earth conductor PE SCHUCH Quality - your advantage: In addition to the great advantages incorporated into our standard series e152.. our emergency light version series e148.. offers quite a number of further outstanding features: Microprocessor controlled intelligent emergency electronic device with integral ECG - "end-of-life switching-off system" basing on the latest technical experiences and standards (EOL test 1 and 2 acc. to IEC , supplement H and IEC ) - multi-function LED with coded indication of the functions, status and potential failures of the electronic device and of the batteries - special signal whenever there is an EOL situation (LED red flashing) - maintained or stand-by wiring - automatic weekly function test - automatic annual 2/3 operating period test - function and operating period test can be effected manually - quick replacement of battery set even in explosive atmosphere Highest degree of safety in case of a lamp failure during the emergency light operation - If there is a lamp failure in case of emergency operation the second lamp will automatically take over the emergency operation Application within a wide range of temperature of -20 C up to + 55 C Best suitable for continuous row installation - Looping the mains cable at one small end of the housing or internal through wiring system in all types 0 C -20 C +55 C 0 C 119e/6 Please observe the notes in the technical supplement

7 e148.././. II 2 G EEx edq IIC T4 for bi-pin fluorescent tubes, socket G13 EC Test Certificate: PTB05 ATEX 2066 Ignition protection:"e" (increased safety) Explosion protection: II 2 G EEx edq IIC T4 (Zone 1) II 2 D T80 C (Zone 21) II 2 D T80 C IP66 Rated voltage: V, AC, (+8% - 10%), 50-60Hz -20 C up to +55 C (recommended) 0 C up to +40 C Suspension hooks H8V P Ceiling brackets 15A P T 26 e T 38 up to 4 cable entries for 1.5h emergency operation with remote switch connection 1h emergency operation e148 22/1/4 4) x T26/18W 70 8,9 e148 42/1/4 4) x T26/36W 35 12,6 3h emergency operation e148 22/3/7 3) x T26/18W 45 9,3 e148 42/3/7 3) x T26/36W 30 13,0 1 h emergency operation, increased light output e148 22/1/7 3) x T26/18W 90 9,3 e148 42/1/7 3) x T26/36W 65 13,0 Further series / equipment Lamps/ Lumin. flux- Weight Watts 1) fact.appr.% appr.kg 1) Also for fluorescent tubes of 38mmØ (T38/..) 3) Battery 7Ah 2) Weights without packing material 4) Battery 4Ah with aluminium mirror-type reflectors (series e S) for high installations with different (luminous flux factors) battery capacity Photo: BASF Mounting material Suspension hooks H8V P Ceiling brackets 15A P Self-adhesive legends for marking escape routes acc. to VGB 125 and DIN /125/33../35../35 Sighting distance acc. to EN 1838 and DIN 4844 = 25m. Accessories / Spare Parts Spare rechargeable batteries Spare diffusers for series e148../ Cable glands Alu mirror-type reflectors, built in SP 21 SP 22 SP 41 SP 42 Mounting material H8V P A P AV P Self-adhesive standard legends 590/125/ /125/ /125/ batterie 4Ah batterie 7Ah spare cover PC for 20 W spare cover PC for 40 W ex-proof plastic cable gland M25 x 1,5 ex-proof plastic cable gland M25 x 1,5 with stopping plug ex-proof plastic plug M25 x 1,5 for 1 x 18 W for 2 x 18 W for 1 x 36 W for 2 x 36 W 2 hooks with bolts, stainless steel 2 ceiling brackets, hot galvanized steel 2 ceiling brackets, stainless steel for e for e for e Weiteres Further accessories Zubehör sowie as well Trageschienensystem as carrier rail systems und and through Durchgangsverdrahtungen wiring systems are siehe available. Baureihe e bzw. Ex-Installationsmaterial. Please observe the notes in the technical supplement 119e/7

8 Explosion-proof Sheet Steel Light Fitting of an Extremely Low Profile Design for Ceiling Mounting or Recessed Mounting Series e191/ Hazardous areas of Zones 1, 21 and 2, 22, e.g. preferably clean rooms, paint shops and spray booths. Housing: Sheet steel, powder coated in white (RAL 9016), stainless steel upon request. Glass cover: Impact resistant safety glass, frameless/hinged. Reflector: White painted sheet steel. Central locking system: Operated by a 5mm allen key, hinges on the opposite side. Circuit breaker (switch): Switching off all poles when the light fitting is opened. Optical indicator showing the actual position of the switch. Wiring: Double-channel ballast with "end-of-life" switching-off system. Connection terminals: Standard: Max. 2,5mm 2 (6,0mm on request). Cable entries: 3 entries M25 x 1,5. (2 glands M25 x 1,5-1 of them is plugged- and 1 blind plug). Through wiring system: Up to 5 x 2,5mm 2 (extra charge / 6,0mm 2 upon request), looping the mains cable on one side is possible. Mounting system: brackets incl. (standard) or separate frame for recessed installation. Schuch Quality - your advantage sturdy design of high chemical resistance for application in rough industrial conditions - housing made from powder coated sheet steel or upon request from stainless steel - frameless safety glass pane - solid central locking system with high grade aluminium hinges reliable, fail safe and long-life thanks to a special ex-proof ECG with high-grade quality features: - "end-of-life switching-off system" i.e. at life end the fluorescent tube is safely switched off (world novelty acc. to the latest IEC standards IEC ) - in compliance with the requirements of over voltage category III (standard = over voltage category II) - widened interference suppression up to 300MHz (standard = 30MHz) - standard: Double channel system with separate lamp operation - extremely favourable operating temperatures thanks to a special quartz sand encapsulation inside an aluminium housing are a guaranty for a long life time best suitable for mounting and maintenance purpose with incorporated safety - central locking system with hingeable safety glass pane for an easy mains connection and lamp replacement - isolating switch with optical indicator showing the actual position of the switch wide range of application and flexibility at most different environmental conditions +60 C - certification for installation in gas and dust atmospheres (zones 1 or 2 and 21 or 22) - for ceiling mount or recessed mount in suspended or insulated ceilings 0 C - for connection to central- or group battery systems with DC-detection and change-over to 1- lamp operation (emergency mode - types e191/192 ZB) - separate frame for recessed installation can be installaed at a later stage, too (modular concept). Thus, a high flexibility of application combined with an economic storing is guaranteed. - bilateral through wiring system or looping system on one side of the housing (on request) - high light efficiency due to an optimized mirror type reflector made of purest aluminium e191.. for bi-pin fluorescent tubes, socket G13 II 2 G EEx edq IIC T4 II 2 D T80 C IP65 T 26 e T 38 EC Test Certificate: IBExU 04 ATEX 1062 Ignition protection: e (increased safety) Explosion protection: II 2 G EEx edq IIC T4 (Zone 1) II 2 D T80 C (Zone 21) Rated voltage: V AC/DC0 or 50 to 60 Hz -20 C up to +60 C (ceiling and recessed mounting: e191..) -20 C up to +50 C (recessed mounting acc. to EN e192..) -20 C up to +40 C (recessed installation into heat insulated ceilings acc. to EN 60598) Temp. Lamps Weight class Watts appr. kg narrow housing e T4 1 x T 26/18 W 10,0 e T4 2 x T 26/18 W 10,0 e T4 1 x T 26/36 W 17,0 e T4 2 x T 26/36 W 17,0 e T4 1 x T 26/58 W 20,0 e T4 2 x T 26/58 W 20,0 119e/8 Please observe the notes in the technical supplement

9 e192.. for bi-pin fluorescent tubes, socket G13 II 2 G EEx edq IIC T4 II 2 D T80 C IP65 Temp. Lamps Weight class Watts appr. kg wide housing e T4 3 x T 26/18 W 18,5 e T4 4 x T 26/18 W 18,5 e T4 3 x T 26/36 W 25,5 e T4 4 x T 26/36 W 25,5 e T4 3 x T 26/58 W 28,5 e T4 4 x T 26/58 W 28,5 Dimensions for recessed mounting Frame for Recessed Installation Light fittings of series e191/192.. may be equipped with a separate frame also at a later stage, thus allowing recessed ceiling or wall installation. The frame is mounted to the long sides of the housing by means of bolts of size M5 (see drawing). slotted hole EB 182/ EB 182/ EB 182/ EB 192/ EB 192/ EB 192/ frame for narrow housing - 1 and 2 x 18W frame for narrow housing - 1 and 2 x 36W frame for narrow housing - 1 and 2 x 58W frame for wide housing - 3 and 4 x 18W frame for wide housing - 3 and 4 x 18W frame for wide housing - 3 and 4 x 18W types Attention: Please do always indicate in your inquiry the kind of ceiling into which the light fitting is intended to be recessed. Methods of recessed installation: - into suspended ceilings - into heat insulated ceilings acc. to EN into clearances in concrete ceilings Attention: When planning the opening for recess installation please allow additional clearance for the cable glands. Further Series / Equipment up to 4 cable entries (also in the base of the housing) different glands through wiring system up to 5 x 6,0 mm 2 (except for types e ) for connection to central- or group battery systems with DC-detection and change-over to 1- lamp operation (emergency mode - types e191/192 ZB) with 2 individual electronic ballasts and monitoring or emergency current supply unit for individual monitoring the light fitting connected to central or group battery systems (except for types e ) with F-profile for mounting into clean room ceilings without separating switch stainless steel version, not polished silicone-free version in Zone 2/22 version (series nd191/192) in non-ex-proof version (series 191/192...) (see catalogue dust-/waterproof light fittings) Accessories / Spare Parts Through wiring system at extra charge. spare glasses Cable entries/cable glands Lamp holder e spare glass for narrow housing - 1 and 2x18W spare glass for narrow housing - 1 and 2x36W spare glass for narrow housing - 1 and 2x58W spare glass for wide housing - 3 and 4x18W spare glass for wide housing - 3 and 4x18W spare glass for wide housing - 3 and 4x18W ex-proof gland of size M25 x 1,5 ex-prro gland with plug of size M25 x 1,5 ex-proof plug of size M25 x 1,5 for recessed installation into concrete clearances ex-proof gland M25 x 1,5 with gasket, heat resistant ex-proof plug M25 x 1,5 with gasket, heat resistant spare ex-proof gasket for 2595 and 2605 ex-proof snap-type/plug-socket holder Please observe the notes in the technical supplement 119e/9

10 Explosion-proof Light Fittings with Tapered Sheet Steel Body Series e181/182.. Hazardous areas of Zones 1, 21 and 2, 22, e.g. paint shops and spray booths. Housing: Sheet steel, powder coated in white (RAL 9016); stainless steel upon request. Glass cover: Impact resistant safety glass pane, frameless and hinged. Reflector: Hinged; white painted sheet steel; detachable. Central locking system: operated by a 5mm allen key, hinges on the opposite side. Circuit breaker (switch): Switching off all poles when light fitting is opened. Optical indicater showing the actual position of the switch. Wiring: Double channel ballast with end-of-life switching-off system. Connection terminals: Standard L1+N+PE, up to 6,0mm 2. Through wiring system: Up to 5 x 2,5mm 2 (etra charge / 6,0mm 2 on request), looping the mains cable on one side is possible. Cable entries: 3 entries M25 x 1,5, (2 glands M25 x 1,5-1 of them is plugged- and 1 blind plug). Mounting: Horizontal. 2 stainless steel hooks (H8V P) or 2 ceiling brackets (15A P) are supplied at extra charge (see accessories). Note: For installation in humid and corrosive atmospheres please select light fittings with housings in stainless steel. When switched off the light fittings must not be exposed to an a.t. of more than +85 C suspension hooks mounting brackets 15A Schuch Quality - your advantage: sturdy design of high chemical resistance for application in rough industrial conditions: - housing made from powder coated sheet steel or upon request from stainless steel - frameless safety glass pane - solid central locking system made from galvanized steel and high-grade aluminium hinges reliable, fail-safe and long-life thanks to a special ex-proof ECG with high-grade quality features: - "end-of-life swiching-off system" i.e. at the end of its life a fluorescent tube is safely switched off (world novelty acc. to the latest IEC draft standards IEC ) - widened interference suppression up to 300MHz (standard = 30MHz) - double channel system for separate lamp operation - extremely favourable operating temperatures thanks to a special quartz sand encapsulation inside an aluminium housing are a guarantee for a long life time best suitable for mounting and maintenance purpose with incorporated safety - central locking system with hingeable safety glass pane for an easy lamp replacement - easily accessible connection compartment via hingeable reflector - isolating switch with optical indicator showing actual position wide range of application and flexibility at most different environmental conditions - certification for installation in gas and dust atmospheres (zones 1 and 21) - application up to temperature class T6 (series e181. T6) - wide and admissible range of ambient temperature from -20 C to +75 C (version "H") - for connection to central- or group battery systems with DC-detection and change-over to 1- lamp operation (emergency mode - types e181/182 ZB - designed for application of fluo tubes of 26mmØ and 38mmØ - separate frame for recessed installation and a swivel arm mounting system can be installed at a later stage, too. A high flexibility of application combined with an economic storing is guaranteed - classical bilateral through wiring system or looping system on one side of the housing (upon request) e181.. for bi-pin fluorescent tubes, socket G13 T 26 e182.. T 38 II 2 G EEx edq IIC T4 EC Test Certificate: IBExU 02 ATEX 1018 Explosion protection: II 2 G EEx edq IIC T4 (Zone 1) II 2 D T50-75 C (Zone 21) Ignition protection: e (increased safety) II 2 D T50-85 C IP65-20 C to +50 C (1 or 2 lamps) -20 C to +40 C (3 or 4 lamps) In special version for ambient temperature up to +75 C. Rated voltage: V AC/DC Frequency: 0 or 50 to 60 Hz. Temp. Lamps Weight class Watts appr. kg narrow housing e T4 1 x T 26/18 W 11,7 e T4 2 x T 26/18 W 11,7 e T4 3 x T 26/18 W 13,6 e T4 1 x T 26/36 W 17,6 e T4 2 x T 26/36 W 19,0 e T4 3 x T 26/36 W 22,9 e T4 1 x T 26/58 W 22,5 e T4 2 x T 26/58 W 22,5 e T4 3 x T 26/58 W 24,6 119e/10 Please observe the notes in the technical supplement

11 e182.. for bi-pin fluorescent tubes, socket G13 II 2 G EEx edq IIC T4 II 2 D T50-85 C IP65 Temp.- Lamps/ Weight class Watts appr. kg wide housing e T4 3 x T 26/18 W 16,0 e T4 4 x T 26/18 W 16,0 e T4 3 x T 26/36 W 24,0 e T4 4 x T 26/36 W 24,0 e T4 3 x T 26/58 W 29,0 e T4 4 x T 26/58 W 29,0 e181/182.. H.. for high ambient temperatures up to +75 C II 2 G EEx edq IIC T4 II 2 D T75-85 C IP65 Like standard types, but with heat resistant cable glands M25 x 1,5 EC Test Certificate, ignition protection, explosion protection and rated voltage like standard types. T 26 T 38 max. Lamps/ Weight amb. temp.watts appr. kg for ambient temperature up to +55 C e H C 3 x T 26/36 W 21,0 e H C 3 x T 26/18 W 16,0 for ambient temperature up to +60 C e H C 3 x T 26/18 W 13,0 e H C 3 x T 26/36 W 24,0 for ambient temperature up to +65 C e H C 2 x T 26/18 W 11,0 e H C 2 x T 26/36 W 19,0 for ambient temperature up to +75 C e H75 1) C 1 x T 26/18 W 11,0 e H C 1 x T 26/36 W 19,0 1) For an a.t. of +75 C light fittings are only allowed without through wiring system (For an a.t. of +70 C type e18121 H70 is allowed with through wiring system.) Please observe the notes in the technical supplement 119e/11

12 e181.. T6 carbon disulphide - T6 II 2 G EEx edq IIC T6 II 2 D T50-65 C IP65 Hazardous areas of Zones 1, 21 and 2, 22, with gases and vapours of temperature class T6 (e.g. carbon disulphide). As before but with bi-pin fluorescent tubes of 38mm Ø only. EC Test Certificate, ignition protection, explosion protection and rated voltage same as series e181../e C to +50 C (1 lamp) -20 C to +40 C (2 lamps) e181.. T6 T 38 Temp.- Lamps/ Weight Class Watts appr. kg narrow housing e T T6 1 x T 38/20 W 11,0 e T T6 2 x T 38/20 W 11,0 Dimensions for recessed installation Frame for Recessed installation retrofit possible Light fittings of series e181../e182.. may be equipped with a separate frame even at a later stage. Also suitable for clean areas. This frame is mounted to the long sides of the housing by means of bolts of size M5 (see drawing). slotted hole Frame a b c d e f EB 181/ EB 181/ EB 181/ EB 182/ EB 182/ EB 182/ Attention: When planning the opening for recess installation please allow additional clearance for the cable glands. EB 181/ EB 181/ EB 181/ EB 182/ EB 182/ EB 182/ Swivel Arm Mounting System retrofit possible frame for narrow housing, 1,2 and 3 x 18 W frame for narrow housing, 1,2 and 3 x 36 W frame for narrow housing, 1,2 and 3 x 58 W frame for wide housing, 3 and 4 x 18 W frame for wide housing, 3 and 4 x 36 W frame for wide housing, 3 and 4 x 58 W Light fittings of series e181../e182.. may be equipped with a swivel arm mounting system at any time even at a later stage. The swivel arms are fixed to the suspension points at the upper side of the housing. Range of swivelling: ± 75 (see dimensions in diagram). SWA 181/ for all types, comprising 2 swivel arms with bolts M8 Swivelling range e/12 Please observe the notes in the technical supplement

13 Further Series / Equipment up to 4 cable entries different glands through wiring system up to 6,0mm 2 (please consult us in case of higher ambient temperatures) with monitoring module for individual monitoring the light fitting connected to central or group battery devices for connection to central- or group battery systems with DC-detection and change-over to 1-lamp operation (emergency mode - types e181/182 ZB) without separating switch (series e181/182.. OS) stainless steel version glass pearl treated silicone-free version zone 2/22 version (series n/nd 181/182..) non-explosion-proof versions (series 181/182...) as dust- and waterproof version vertical mounting for zones 21 and 22 (particularly dust hazardous areas) (series e187/188..) and (series nd187/188...) Mounting devices Suspension hooks H8V P Ceiling brackets 15A P Wall angle WD 45 P Accessories / Spare Parts Spare glass panes Cable entries/glands Lamp holder e Mounting material H8V P A P AV P WD 45 P for narrow housings, 1, 2 und 3 x 18 W for narrow housings, 1, 2 und 3 x 36 W for narrow housings, 1, 2 und 3 x 58 W for wide housings, 3 und 4 x 18 W for wide housings, 3 und 4 x 36 W for wide housings, 3 und 4 x 58 W for e181.. and e182.. explosion-proof cable gland M25 x 1,5 explosion-proof cable gland with plug (M25 x 1,5) explosion-proof plug M25 x 1,5 for e181.. H.. and e182.. H.. ex-proof gland M25 x 1,5 with gasket, heat resitant ex-proof gland M25 x 1,5 with gasket, heat resistant spare gasket for 2595 and 2605 ex - rotary-type plug-in lamp holder 2 hooks with bold M8, stainless steel 2 ceiling brackets, steel hot galvanized 2 ceiling brackets, stainless steel 2 wall/ceiling angle, steel Further accessories as well as carrier rail systems and through wiring systems are available. Please observe the notes in the technical supplement 119e/13

14 Explosion-proof Sheet Steel Light Fittings with Roof-type Housing Series e187/188.. Hazardous areas of Zones 1, 21 and 2, 22, especially for dust hazardous areas of Zones 21/22 Housing: Sheet steel, powder coated in light grey (RAL 7035), alternatively blasted stainless steel. Glass cover: Frameless safety glass pane, hinged. Reflector: Sheet steel coated in white, removable. Central locking system: 5mm hexagon socket. Circuit breaker (switch): Switching off all poles when the light fitting is opened. Positively driven optical indicator showing the actual position of the switch. Wiring: Double channel ballast, with "end-of-life switching-off sytem" Connecting terminal: Standard L1 + N +PE, up to 6,0mm 2. Cable entries: 3 entries (2 glands, one with stopping plug and 1 locking screw, M25 x 1,5). For some versions heat resistant connecting cable is needed. Mounting: Horizontal, with 2 eyebolts RS6 (see accessories). Through wiring system: Up to 5 x 2,5mm 2 (extra charge), looping the mains cable at one side is possible. Note: For installation in humid and corrosive atmospheres please select light fittings with housings in stainless steel. When switched off the light fittings must not be exposed to an a.t. of more than +85 C. eye bolt RS 6 Schuch Quality - your advantage: sturdy design of high chemical resistance for application in rough industrial conditions: - housing in a special dust repellent design, made from powder coated sheet steel or upon request from stainless steel - frameless safety glass pane - solid central locking system made from galvanized steel and high-grade stainless steel hinges reliable, fail-safe and long-life thanks to a special ex-proof ECG with outstanding quality features: - "end-of-life swiching-off system" i.e. at the end of its life a fluorescent tube is safely switched off (world novelty acc. to the latest IEC standards, draft standard IEC ) - in compliance with the requirements of over voltage category III (standard = over voltage category II) IEC widened interference suppression up to 300MHz (standard = 30MHz) - double channel system for separate lamp operation - extremely favourable operating temperatures thanks to a special quartz sand encapsulation inside an aluminium housing are a guaranted for a long life best suitable for mounting and maintenance purpose with integrated safety - central locking system with hingeable safety glass pane for an easy lamp replacement - easily accessible connection compartment via hingeable reflector - isolating switch with optical indicator showing actual position wide range of application and flexibility at most different environmental conditions - certification for installation in gas and dust atmospheres (zones 1 and 21) - wide and admissible range of ambient temperature from -20 C to +75 C (types...h) - for connection to central- or group battery systems with DC-detection and change-over to 1-lamp operation (emergency mode - types e181/182 ZB) - disigned for application of fluo tubes of 26mmØ and 38mmØ - classical bilateral through wiring system or looping system on one side of the housing (upon request) e187.. for bi-pin fluorescent tubes, socket G13 EC Test Certificate: IBExU 02 ATEX 1018 Explosion protection: II 2 G EEx edq IIC T4 (Zone 1) II 2 D T50-75 C (Zone 21) Ignition protection: e (increased safety) T 26 e T 38 II 2 G EEx edq IIC T4 II 2 D T50-85 C IP65-20 C to +50 C (1 or 2 lamps) -20 C to +40 C (3 or 4 lamps) In special version for ambient temperature up to +75 C. Rated voltage: V AC/DC Frequency: 0 or 50 to 60 Hz. Temp. Lamps Weight class Watts appr. kg narrow housing e T4 1 x T 26/18 W 12,6 e T4 2 x T 26/18 W 12,6 e T4 3 x T 26/18 W 14,4 e T4 1 x T 26/36 W 20,2 e T4 2 x T 26/36 W 20,2 e T4 3 x T 26/36 W 22,0 e T4 1 x T 26/58 W 23,8 e T4 2 x T 26/58 W 23,8 e T4 3 x T 26/58 W 25,8 119e/14 Please observe the notes in the technical supplement

15 e188.. for bi-pin fluorescent tubes, socket G13 II 2 G EEx edq IIC T4 II 2 D T50-85 C IP65 wide housing e T4 3 x T 26/18 W 17,6 e T4 4 x T 26/18 W 17,6 e T4 3 x T 26/36 W 25,2 e T4 4 x T 26/36 W 25,2 e T4 3 x T 26/58 W 29,0 e T4 4 x T 26/58 W 29,0 e187/188.. H.. for high ambient temperatures up to +75 C II 2 G EEx edq IIC T4 II 2 D T75-85 C IP65 Like standard types, but with heat resistant cable glands M25 x 1,5 EC Test Certificate, ignition protection, explosion protection and rated voltage like standard types. T 26 T 38 up to 4 cable entries various types of glands with through wiring system up to 6 x 6.0 mm 2 (for applications in areas with higher ambient temperatures please consult us, series e187/188.. H..) with looping the mains cable at one end with 2 individual electronic ballasts and a monitoring device for individual monitoring of a light fitting connected to central or group battery systems with DC-detection and switching over to 1-lamp DC-operation. Application in group- or central battery systems (series e187/188 ZB) max. Lamps/ Weight amb. temp.watts appr. kg for ambient temperature up to +55 C e H C 3 x T 26/36 W 22,0 e H C 3 x T 26/18 W 17,6 for ambient temperature up to +60 C e H C 3 x T 26/18 W 14,4 e H C 3 x T 26/36 W 25,2 for ambient temperature up to +65 C e H C 2 x T 26/18 W 12,6 e H C 2 x T 26/36 W 20,2 for ambient temperature up to +75 C e H75 1) C 1 x T 26/18 W 12,6 e H C 1 x T 26/36 W 20,2 1) For an a.t. of +75 C light fittings are only allowed without through wiring system Further series / equipment - at extra charge (For an a.t. of +70 C type e H70 is allowed with through wiring system.) without circuit breaker available with blasted stainless steel housing silicone-free version zone 2/22 version (series nd187/188 ) non explosion proof version (series 187/188, see water-/dust-proof fittings in catalogue) T6-version (types e187 21/22 T6) Further accessories as well as carrier rail systems and through wiring systems are available. Accessories / Spare Parts Spare glass panes Cable entries/glands Lamp holder e Mounting material RS for narrow housings, 1, 2 und 3 x 18 W for narrow housings, 1, 2 und 3 x 36 W for narrow housings, 1, 2 und 3 x 58 W for wide housings, 3 und 4 x 18 W for wide housings, 3 und 4 x 36 W for wide housings, 3 und 4 x 58 W for e187/188.. explosion-proof cable gland M25 x 1,5 explosion-proof cable gland with plug (M25 x 1,5) explosion-proof plug M25 x 1,5 for e187/188.. H.. ex-proof gland M25 x 1,5 with gasket, heat resitant ex-proof gland M25 x 1,5 with gasket, heat resistant spare gasket for 2595 and 2605 Ex - rotary-type plug-in lamp holder eyebolt Please observe the notes in the technical supplement 119e/15

16 Explosion-Proof Light Fitting for Industrial Application / with Induction- Lamp System ENDURA - Series e ENDURA Hazardous areas of Zones 1 and 2, workshops, warehouses,loading and unloading areas under roof, especially at places which are not easily accessible and where a lamp replacement may be a costly matter or if generally long maintenance intervals are wanted for cost saving. Housing: Sheet steel, powder coated in light grey (RAL 7035), with inductiontype lamp and ECG. Glas: Frameless safety glass pane, hinged, locking by 2 socket head screws. Reflector: Reflector system optimized for the ENDURA lamp, made from matt finished purest aluminium. Connection terminals:l + N + PE 2,5mm 2 max. Cable entry:1 cable gland M25 x 1,5, 1 plug M25 x 1,5 (both on same side) Mounting position: Horizontal. Mechanical installation: Angle brackets for direct ceiling mounting (4 borings of a 9mm Ø) or suspension by means of chains or steel ropes with spring hooks. First ex-proof compact projector with induction-type light system certified in "increased safety version". Shock tested RK 1.6/16A e ENDURA High bay version LMT EC Test Certificate: PTB 99 ATEX 2065 Ignition protection:e (increased safety) Explosion protection:ii 2 G EEX ed IIC T4 II 2 G EEx ed IIC T4 IP65-30 C up to +40 C Rated voltage: 220 to 240 V AC/DC,0 up to 50/60 Hz Advantages of the induction-type light system ENDURA: Extremely long life (60,000 hrs) Flicker-free instant start within < 0.1 sec., suitable as emergency illumination Instant reignition with almost full light output Constantly high luminous flux over a large range of mains voltage, suitable for D.C. voltage Low ignition temperature and costantly high luminous flux over a wide temperature range, suitable for low temperatures at outdoor areas, down to -30 C Maintenance-free e2070/150 ENDURA Article. no. Temp. Lamp/ Weight class Watt appr.kg 1) with induction-type lamp and ECG (electronic control gear) e2070/150 ENDURA T4 1 x LMT-SIHF ,0 1) weight without packing material Further Series / Equipment with different cable glands with incorporated isolating switch with blasted stainless steel housing, powder coating upon request with frame for recessed installation with swivel bracket up to 45 (ceiling and wall mounting) Accessories / Spare Parts 2070/ SWB spare glass pane swivel bracket with accessories ex-proof plastic cable gland M25 x 1,5 ex-proof plug M25 x 1,5 119e/16 Please observe the notes in the technical supplement

17 Explosion-proof Oval-shaped Light Fittings for GLS Lamps up to 100 W Series e2691/ A Hazardous locations of zones 1/21 and 2/22. Housing: Diecast aluminium. Glass: Clear thermal glass. Wire guard: Galvanized steel (OSK without wire guard). Cable entry system / connection terminals: e2691 A (with connection box): 2 entries of size M25 x 1,5 (2 ex-proof plastic glands, 1 of them with ex-proof plastic plug); 3 terminals, max. connection range 6,0mm 2. e2692 A (without connection box): 2 entries M20 x 1,5 (1 ex-proof metal gland, 1 ex-proof metal plug), mains connection with heat resistant cable (up to 145 C). 3 terminals, max. connection range 2,5mm 2. Mounting: Any method except: 100W, 230V AC/DC and 60W, 24V or 42 V AC/DC vertical wall mounting with downward lamp direction not allowed. Mounting: 2 cast on brackets for wall or ceiling mounting. SCHUCH Quality - your advantage: Series e with wire guard robust industrial design for reliable and safe long-term use - sturdy and corrosion-resistant housing made of cast aluminium - all outer screws and bolts made of stainless steel - shock and temperature resistant safety glass - additional safety due to robust wire guard easy to install and to maintain - cost efficient, no separate junction box needed when installing type e2691 with cast on connection box in increased safety. - continuously adjustable tilt angle for applications in different ambient conditions - for 24V, 42V and 230V AC/DC - ATEX-certified for gas and dust hazardous areas (Zones 1,21 and 2,22) - ATEX-certified for explosion group II C Series e without wire guard e2691/2692 A with or without connection chamber II 2 G EEx ed IIC T2-T4 EC Test Certificate: PTB 03 ATEX 2164X Ignition protection: e (increased safety) Rated voltage: 24V, 42V, 230V AC/DC II 2 D T150 C IP65 Explosion protection: II 2 G EEx ed IIC T2-T4 II 2 D T150 C -20 C up to +40 C Series e with wire guard e2691/2692 A A Lamps Voltage Temp. Weight Watts class appr. kg for GLS lamps of brands OSRAM or RADIUM acc. to DIN part 5b8, socket E27 with connection chamber e2691 A A25/ T4 2,5 A T3 2,5 A100 1) 230 T2 2,5 A25/40/60 24/42 T2 2,5... without wire guard e2691 A OSK see above 2,3 without connection chamber e2692 A see above 2,2... without wire guard e2692 A OSK see above 2,0 Series e without wire guard Further Series / Equipment - e2691: with 5 terminals, max. connection range 2,5mm 2 - e2692: with cable entries M25 x 1,5mm 2 Accessories / Spare parts 2693 tw ATEX SK 693 A spare glass spare wire guard cable gland M25 x 1,5 (for e2691 A) cable gland with plug M25 x 1,5 (for e2691 A) brass gland M20 x 1,5 with gasket (for e2692 A) brass plug M20 x 1,5 with gasket (for e2692 A) Please observe the notes in the technical supplement 119e/17

18 Explosion-proof Light Fitting for Lamps up to 250 W Series d Hazardous locations of zones 1 and 2; high installations in tank stations etc. Housing and glass retaining ring: From weather resistant cast aluminium, powder coated in light grey (RAL 7035), with hinged retaining ring and locking bolt, roller ring gasket; ballast, condenser and if necessary ignitor are located in the upper section of the housing Globe: Thermal glass located in the glass retaining ring. Connection terminals: Standard: L1+N+PE max. up to 6,0mm 2 ; up to 10mm 2 upon request; internal and external connection of earth conductor. Cable entries: 2 entries M25 x 1,5 (1 gland, 1 locking screw). Lamp replacement: Unscrew the globe retaining ring which is laterally held by the housing. Mounting method: Vertical or swivelled up to ± 40 off-centre. Mechanical installation: Variable; accessories please see spare parts / accessories. SCHUCH Quality - your advantage Suspension 2 x RS10 Ceiling bracket 62 A robust industrial design for reliable and safe long-term use - sturdy and corrosion-resistant housing made of cast aluminium - all outer screws and bolts made of stainless steel - solid, shock and temperature resistant safety glass dome easy to install and to maintain - easy installation due to cast on connection box in increased safety - easy lamp replacement due to hinged glass retaining ring For applications in different ambient conditions - for various lamp types (metal halide-, sodium discharge-, mercury vapour-, halogen-, blended-, induction- and fluorescent lamps) - for lamps from 26W to 250W - ATEX-certified for gas hazardous areas of zones 1 and 2 - ATEX-certified for explosion group II C up to temperature class T6 - wide range of admissible ambient temperatures -20 C up to +50 C +50 C 0 C d6300 in flameproof encapsulation II 2 G EEx de IIC T4-T6 IP66/67 Mounting 63 SWB Swivelling range ± 40 adjustable in steps of 10 Grille de protection SK Wall mounting system TC-DEL HIE TC-TEL HSE d6300/250 HME HME-SB EC Test Certificate: PTB 98 ATEX 1122 Ignition protection: d (flameproof encapsulation) Explosion protection: II 2 G EEx de IIC T4-T6 20 C up to +40 C/+50 C Rated voltage: Standard: KVG: 230 V, 50 Hz; EVG (ECG): V AC/DC Frequency: 0 or Hz. Temp. Lamps/ Weight class Watts appr.kg 3) for compact fluorescent lamps, socket G24q or Gx24q, with electronic ballast (EVG) d6300/226kl EVG 1) T6 2 x TC-DEL 26 or 14,5 2 x TC-TEL 26 d6300/32kl EVG 1) T6 1 x TC-DEL 32 or 14,5 1 x TC-TEL 32 d6300/42kl EVG 1) T6 1 x TC-DEL 42 or 14,5 1 x TC-TEL 42 for blended lamps, socket E40 d6300/250 ML T4 1 x HME-SB ,0 for high pressure discharge lamps, socket E27 or E40 d6300/125 1) ) T4 1 x HME ,2 d6300/ ) T4 1 x HME ,2 d6300/100 HI 1) ) T5 1 x HIE ,2 d6300/150 HI ) T5 1 x HIE ,2 d6300/250 HI ) T4 1 x HIE ,2 d6300/100 HS 1) ) T5 1 x HSE ,2 d6300/150 HS 1) ) T5 1 x HSE ,2 d6300/250 HS ) T4 1 x HSE ,2 1) Admissible ambient temp.: +50 C 3) Weights without packing material 2) Uncomp., article nos. for comp. see price list 119e/18 Please observe the notes in the technical supplement

19 d6300 H50 for high ambient temperatures up to +50 C II 2 G EEx de IIC T4/T5 IP66/67 The types for compact fluorescent lamps as well as for high pressure discharge lamps < 250W as well as for blended lamps have been certified for +50 C a.t. in their standard version. HME HIE HSE Temp.- Lamps Weight class Watts appr.kg 2) for high pressure discharge lamps, socket E27 or E40 d6300/250 H T4 1 x HME ,2 d6300/150 HI H ) T5 1 x HIE ,2 d6300/250 HI H ) T4 1 x HIE ,0 d6300/250 HS H ) T4 1 x HSE ,0 1) Uncomp., article nos. for comp. see price list 2) Weights without packing material World-wide first flameproof luminaire certified with induction-type lamp system. Advantages of the induction-type lighting system "QL": extremely long life ( 60,000 hours) flicker-free instant start within < 0.1sec., suitable as emergency lighting instant re-ignition (almost full light output) constantly high luminous flux over a large voltage range, suitable for DC low ignition temperature and constantly high luminous flux over a wide temperature range, suitable for low temperatures and outdoor application any position of operation maintenance-free d6300 QL with induction-type lighting system QL d6300/165 QL LMG For installation at locations difficult to reach for lamp replacement or where long maintenance intervals are wanted for cost savings. As before but with induction-type lamp and ECG (electronic control gear). -20 C up to +40 C. Rated voltage: V AC/DC; 0 or 50 to 60 Hz. Article. no. Temp.- Lamps Weight Class Watt appr. kg with induction-type lamp and electronic control gear (EVG) d6300/85 QL T6 1 x LMG-IHF 85 14,5 d6300/165 QL T6 1 x LMG-IHF ,5 Further Series / Equipment with connection terminals up to 10mm² with 2 cable glands with ex-proof cable glands different from the standard ones with incorporated switch operating when the light fitting is opened II 2 G EEx de IIC T6 IP66/67 hard coated version for installation in very aggressive atmospheres with wire guard with external reflector with swivel arm for blended lamps HME-SB W d 6300 with external reflector of high bay and low bay versions 64 SB 63 ST Accessories / Spare Parts 63 ST SB MS RS 10 P A SWB Foto: BASF external reflector narrow beam external reflector wide beam ex-proof plastic cable gland M25 x 1,5 (for d6300/... QL,.../ HI,.../ HS) ex-proof brass gland M25 x 1,5 (for.../250hi,... H50,.../250HS,.../125,.../250 and.../ 250ML) 1 pair of eye bolts, galvanized steel, M10 ceiling bracket, galvanized steel swivel arm, galvanized steel Please observe the notes in the technical supplement 119e/19

20 Explosion-proof Floodlight for Lamps up to 500W Series d Hazardous locations of zones 1, 2 and 21, 22, on- and offshore installations, loading stations, oil rigs, silos etc. Housing and glass retaining frame: From weathering resistant cast aluminium. Lateral lockable screw cap for lamp replacement. Ballast and ignitor inside the housing. Condenser box: Mounted to the back of the floodlight. Reflector: Made from high anodized purest aluminium. Glass pane: Tempered safety glass resistant to temperature variations, glued into the frame. Connection terminals: Standard: L1+N+PE - 4mm², in case of compensated version 6mm 2 Cable entries: 2 entries M25 x 1,5 (1 plastic gland + 1 plug) Mounting position: Horizontal. Mechanical installation: 1 steel bracket. SCHUCH Quality - your advantage: robust industrial design for reliable and safe long-term use - sturdy and corrosion-resistant housing made of cast aluminium - all outer screws and bolts made of stainless steel - solid, shock and temperature resistant safety glass pane easy to install and to maintain - easy installation and lamp replacement through screw cap - continuously adjustable tilt angle for applications in different ambient conditions - for various lamp types (metal halide-, sodium discharge-, mercury vapour-, halogen lamps) - for lamps from: d w to 250W d w to 1000W - for 120V, 220V, 230V, 240V and 255V - ATEX-certified for gas and dust hazardous areas (Zones 1,21 and 2,22) and explosion group II C - wide range of admissible ambient temperatures -20 C up to +55 C +55 C 0 C d II 2 G EEx de IIC T2-T4 flameproof enclosure, up to 500W, low bay version II 2 D T C IP67 with condenser box m 4015 Swivelling range: ± 90 QT HME HIE HSE HIT HST d3000/500 QT d3000/250 EC Test Certificate: PTB 04 ATEX 1023 Ignition protection: d (flameproof) Explosion protection: II 2 G EEx de IIC T2 - T4 (Zone 1) II 2 D T C (Zone 21). Temp. Lamps Weight class Watts appr.kg 6) for tungsten halogen lamps up to 500W, socket E40 20 C up to + 40 C / +55 C Rated voltage: Standard: 230V, 50 Hz,220V or 240V, 50 Hz or 60 Hz. d3000/250 QT T3 1 x QT 250 W 23,0 d3000/500 QT T2 1 x QT 500 W 3) 23,0 for high pressure discharge lamps, socket E40 d3000/ ) T4 1 x HME ,2 d3000/ ) T3 1 x HME ,0 d3000/70 HS ) T4 1 x HSE/HST 70 24,2 d3000/150 HIE E27 2)5) ) T4 1 x HIE ,0 d3000/150 HI/HS E40 2)4) ) T4 1 x HIT/HSE/HST ,0 d3000/250 HI/HS 2) ) T3 1 x HIE/HIT/HSE/HST ,0 1) Uncomp., article no. for comp. (with condenser box m4015) see price list. 2) Only such metal halide lamps may be used which are allowed to be operated with hpsv ballasts 3) PHILIPS IDE 4) socket E40 5) Socket E27 6) Weights without packing material 119e/20 Please observe the notes in the technical supplement