Emergency Light Fittings

Transcription

1 Emergency Light Fittings

2 SCHUCH Emergency Light Fittings NEW NEU /25.. Dustproof/waterproof emergency light fitting for wind power stations. Description Series Page Polyester with Diffuser Insulation class II Insulation class I Polyester without Diffuser Insulation class II NEW NEU /... Small shock resistant emergency light fitting for wind power stations. Emergency Light Fittings for Wind Power Stations Insulation class I Emergency Light Power Supply Unit Emergency Light Fitting

3 Dustproof/Waterproof Polyester Emergency Light Fittings of Insulation Class II Series 161/ For illumination of working places and acc. to DIN VDE 0108 for illuminating and identifying escape routes etc. Mechanical Data: Housing: Glass fibre reinforced polyester resin, polyurethane gasket. Diffuser: Injected clear acrylic glass or polycarbonate (PC) each with internal prisms. Closure: External plastic clips (KK). Stainless steel clips (KE) available upon request and at extra charge. Reflector: Glass fibre reinforced polyester resin, that can be suspended or removed. It carries the electrical components which are protected against accidental contact. Connection: 3-pole plug-in terminal. Cable entry: 2 plugs M20 x 1,5. Looping the cable at one small end of the housing upon request and at extra charge. Through wiring system: Up to 5x2,5mm 2 (extra charge). Mounting system: Closed knock-outs for direct ceiling mounting, rubber sealing washers inside each fitting. Wiring diagram maintained operation light switch Wiring diagram maintained operation Electrical Data: (series 161/ only) Incorporated NiCd battery set which is constantly charged and therefore ready for operation any time. Visual monitoring the battery charging process through LED. Electronic deep discharge protection. Re-charging time: 24 hours acc. to EN Luminous flux raising i.e. initially the emergency lamp has got a higher luminous flux. Modes of functioning: Maintained operation = in case of mains failure 1 lamp is switched over to battery operation. In the 2-lamp version (type ) only one lamp will be operating as emergency lighting. Connection voltage: 230V, 50Hz (standard) Ambient temperatures convent. ballast: -5 C up to +30 C (maintained version) -5 C up to +40 C (stand-by version) Ambient temperatures (EVG): -5 C up to +40 C (maintained version) light switch Starting: Connect battery conductor Out of operation: Disconnect battery conductor Stand-by operation: Do not connect L1' Shock resistance test: RK 1,6 / 16A 161/ with battery set T T 38 Type Article no. Lamps/ Flux factor Weight Watts approx. % approx. kg 1 hour emergency operation, with conventional ballasts IP /34/ x T 26/36 W 34 4, /18/1 5) x T 26/36 W 18 4, /22/ x T 26/58 W 22 4, /15/1 5) x T 26/58 W 15 4, /65/ x T 26/18 W 65 3, /38/1 5) 6) x T 26/18 W 38 3, /34/ x T 26/36 W 34 5, /50/ x T 26/36 W 50 7, /18/1 5) 6) x T 26/36 W 18 5, /22/ x T 26/58 W 22 7, /31/ x T 26/58 W 31 7, /15/1 5) 6) x T 26/58 W 15 7,2 Series Series hour emergency operation, with electronic ballast (EVG) /34/1 EVG x T 26/36 W 34 3, /18/1 EVG 4) 5) x T 26/36 W 18 3, /22/1 EVG x T 26/58 W 22 4, /15/1 EVG 4) 5) x T 26/58 W 15 3, /65/1 EVG x T 26/18 W 65 3, /38/1 EVG 4) 5) 6) x T 26/18 W 38 3, /34/1 EVG x T 26/36 W 34 7, /50/1 EVG x T 26/36 W 50 5, /18/1 EVG 4) 5) 6) x T 26/36 W 18 4, /22/1 EVG x T 26/58 W 22 5, /31/1 EVG x T 26/58 W 31 6, /15/1 EVG 4) 5) 6) x T 26/58 W 15 5,6 1) Wiring uncompensated only 2) Ratio effective lamp flux/nominal flux 3) Weights without packing material 4) MA version possible (see further series) 5) 3h emergency operation possible 6) shock proof versions Bitte Subject beachten to technical Sie die changes Hinweise im Technischen Anhang! 202

4 161/ EVG for connection to central power supply unit For connection to group or central battery systems or to an emergency mains for illuminating escape routes, ships or vehicles etc. IP65 Electrical design: Electronic ballasts (230V AC / DC). A double lamp luminaire will be equipped with 2 electronic ballasts, separate lamp circuits and separate connection terminals.! T EVG T 38 Type Article no. Lamps/ Weight Watts approx. kg with electronic ballast (EVG) EVG 2) x T 26/18 W 1, EVG x T 26/36 W 2, EVG x T 26/58 W 3,0 with 2 individual electronic ballasts (EVG/2) EVG/2 2) x T 26/18 W 2, EVG/ x T 26/36 W 2, EVG/ x T 26/58 W 4,0 1) Weights without packing material Further series / equipment for series 161/ only:.../b stand-by system = emergency lighting in case of mains failure only (series with 1 lamp = only).../p button for testing the emergency light function.../3 3 hour emergency operation for series 161/ EVG only: with separate or integrated monitoring module for connection to group or central power supply unit with system for monitoring each individual luminaire. (For any inquiry please indicate the make of the equipment used.) with electronic ballast for voltages: 110V AC/DC, 24V DC Type with legend.../35 for types 161/162.../.. EVG only:.../ma automatic monitoring the emergency light fitting with weekly functioning test and annual opwaking period test according to DIN VDE 0108, indication of the test results by LED (luminescence diode) at the luminaire. For further equipment please see catalogue section Dustproof / Waterproof luminaires of series 161/ Emergency Notleuchten Light Fittings Self adhesive legends.../33 W.../34 W.../35 W for escape route identification acc. to BGV A8 and DIN Sighting distance acc. to EN 1838 and DIN 4844 = 25m. Accessories / Spare Parts Type Article no. Self adhesive legends for series and /125/33 W /125/34 W /125/35 W Emergency exit to the left Emergency exit to the right Emergency exit below For further accessories and spare parts please see catalogue section Dustproof / Waterproof luminaires of series 161/ When ordering any electronic components or battery sets please do always indicate the type nos. of the light fittings. 203 Bitte beachten Sie die Hinweise Subject im to Technischen technical changes Anhang!

5 Dustproof / Waterproof Polyester Emergency Light Fittings of Insulation Class I Series 163/ For illumination of working places and acc. to DIN VDE 0108 for illuminating and identifying any escape routes etc. Mechanical Data: Housing: Glass fibre reinforced polyester resin, polyurethane gasket. Diffuser: Stippled clear acrylic (PMMA) with impact resistant component or polycarbonate (PC), hinged at one side. Closure: External plastic clips (KK). Stainless steel clips (KE) upon request and at extra charge. Reflector: Sheet steel, finished in white, detachable, carrying the electrical components. 'Quick release' turn buckle fasteners for quick installation. Connection: 4-pole connection terminal. Cable entries: At the small front sides and at the upper side of the housing, also for looping the mains cable at one side (types also at the long side), 2 plugs M20. Through wiring system: Up to 7x2,5mm 2 or 5x4mm 2 (extra charge). Mounting system: 2 points for direct ceiling mounting; rubber gaskets and washers inside the fitting. Wiring diagram maintained operation light switch Electrical Data: Incorporated NiCd battery set which is constantly charged and therefore ready for operation at any time. Visual monitoring the battery charging process by LED (luminescence diode). Electronic deep discharge protection. Re-charging time: 24 hours acc. to EN Modes of functioning: Maintained operation = in case of mains failure 1 lamp is switched over to battery operation. Connection voltage: 230V, 50Hz (standard) Ambient temperatures: -5 C up to +30 C (maintained version) -5 C up to +40 C (stand-by version) Ambient temperature (EVG): -5 C up to +40 C (maintained version) Wiring diagram maintained operation light switch Starting: Connect battery conductor Out of operation: Disconnect battery conductor Stand-by operation: Do not connect L1' 163/ with battery set T /... Type Article no. Lamps/ Flux factor-weight Watts Watts approx. % 2) approx. kg 3) 1 hour emergency operation, with conventional ballast /18/ ) 1 x T 26/36 W 18 3, /15/ ) 1 x T 26/58 W 15 4, /38/ x T 26/18 W 38 3, /18/ ) 2 x T 26/36 W 18 5, /15/ ) 2 x T 26/58 W 15 6,6 1 hour emergency operation, with electronic ballast (EVG) /18/1 EVG x T 26/36 W 18 3, /15/1 EVG x T 26/58 W 15 3, /38/1 EVG x T 26/18 W 38 3, /18/1 EVG x T 26/36 W 18 4, /15/1 EVG x T 26/58 W 15 4,9 1) Wiring uncompensated only 2) Ratio effective lamp flux/nominal flux IP65 3) Weights without packing material Series Series Bitte Subject beachten to technical Sie die changes Hinweise im Technischen Anhang! 204

6 163/ EVG for connection to central power supply unit For connection to group or central battery systems or to an emergency mains for illuminating escape routes or for emergency lighting on ships, vehicles etc. IP65 Electrical design: Electronic ballasts (230V AC / DC). A double lamp luminaire will be equipped with 2 electronic ballasts, separate lamp circuits and separate connection terminals.! EVG T 26 Type Article no. Lamps/ Weight Watts approx. kg 1) with electronic ballast (EVG) EVG 2) x T 26/18 W 1, EVG x T 26/36 W 2, EVG x T 26/58 W 2,6 with 2 individual electronic ballasts (EVG) EVG/2 2) x T 26/18 W 2, EVG/ x T 26/36 W 3, EVG/ x T 26/58 W 5,0 1) Weights without packing material Further series / equipment for series 163/ only::.../b stand-by system = emergency lighting in case of mains failure only (series with 1 lamp = only).../p button for testing the emergency light function.../3 3 hour emergency operation Special version for wind power stations (see special data sheet). for series 163/ EVG only: with electronic ballast (EVG) for the following voltages: 110 V DC, 24V DC with separate or integrated monitoring module for connection to group or central battery systems with device for monitoring each individual luminaire.(for any inquiry please indicate the make of the equipment used.). for series 163/ EVG only:.../ma automatic monitoring the emergency light fitting with weekly functioning test and indication of the test results by LED (luminescence diode) at the luminaire For further equipment please see catalogue section Dustproof / Waterproof luminaires of series 163 / Notleuchten für Windkraftanlagen auf Anfrage lieferbar. Emergency Notleuchten Light Fittings Type with legend.../35 Self adhesive legends.../33 W.../34 W.../35 W for escape route identification acc. to BGV A8 and DIN Sighting distance acc. to EN 1838 and DIN 4844 = 25m. Accessories / Spare Parts Type Article no. Self adhesive legends for series and /125/33 W /125/34 W /125/35 W Emergency exit to the left Emergency exit to the right Emergency exit below For further accessories and spare parts please see catalogue section Dustproof / Waterproof luminaires of series 163/ When ordering any electronic components or battery sets please indicate the type nos. of the light fittings. 205 Bitte beachten Sie die Hinweise Subject im to Technischen technical changes Anhang!

7 Polyester Emergency/Escape Sign Light Fittings Series KL B/D In humid, wet and dusty locations, commercial and industrial premises, agricultural buildings, car parks, basements, kitchens, protective locations for civil defence, for illumination and identification of escape routes. Mechanical Data: Housing: Glass fibre reinforced polyester, polyurethane gasket. Difuser: Clear stippled PMMA with impact resistant components, hingeable on both sides. Also available in white (W) or clear (K) PMMA or clear stippled (PC) or clear (K PC). Closure: plastic clips (KK). Stainless steel (KE) upon request and at extra charge. Reflector: Sheet steel finished white, detachable, carrying the electrical components. 'Quick release' turn buckle fasteners allow a quick installation. Connection: 3/4-pole connection terminal. Cable entries: At the small front sides and at the upper side of the housing, also for looping the mains cable at one side, 2 plugs M20. Through wiring system: At extra charge. Mounting system: 2 points for direct ceiling mounting; rubber gaskets and washers inside the fitting. Wiring diagram KL B stand-by Wiring diagram KL D maintained Electrical Data: NiCd battery set - gastight - mounted on the reflector. The battery set is constantly charged and therefore ready for operation at any time. Visual monitoring the battery charging process through LED (luminescence diode). Electronic deep discharge protection. Re-charging time: 24 hours acc. to EN NEW Baureihe LED: 3 x 1W LUXEON Highpower-LED NiMH-Batterie Modes of functioning:... B =stand-by operation = in case of mains failure the lamp is on.... D =maintained operation = in case of mains failure the lamp is switched over to battery operation. Connection voltage: 230V, 50Hz (standard) Ambient temperatures: -5 C up to +30 C (maintained version) -5 C up to +40 C (stand-by version) light switch Starting: Connect battery conductor Out of operation: Disconnect battery conductor Stand-by operation: Do not connect L1' KL B/D / D with battery set T 16 TC-SEL KL TC - L Type Article. Lamps/ Em.- Flux factor Weight no. Watts hours appr.% 2) kg 4) maintained or stand-by version 1) IP /45 KL B/D x T 16/8 W , /36 KL B/D x T 16/8 W , /25 KL B/D x TC-SEL 11 W , /20 KL B/D x TC-SEL 11 W ,4 stand-by version (B) 1) /39 KL B x TC-L 18 W , /46 KL B x TC-L 18 W ,4 maintained version (D) with electronic ballast (EVG) /45 KL D1 EVG x T 16/8 W , /36 KL D3 EVG x T 16/8 W , /25 KL D1 EVG x TC-SEL 11 W , /20 KL D3 EVG x TC-SEL 11 W ,9 1)Wiring uncompensated only 2) Ratio effective lamp flux/nominal flux 3) 4) Weights without packing material NEW KL LED IP 65 Note: An EXIT sign on 2 sides requires 2 light fittings which are connected by means of a ceiling or a wall bracket (see accessories / spare parts). LED Type Article. Lamps/ Em.- Flux factor Weight no. Watts hours appr.% 2) kg 4) W KL LED/1/MA x LED 1 W , W KL LED/3/MA x LED 1 W ,0 Bitte Subject beachten to technical Sie die changes Hinweise im Technischen Anhang! 206

8 KL EVG for connection to central power supply unit IP 65 Series KL SB Series KL ST T 16 TC-SEL TC- L LED KL KL SB KL ST For connection to group or central battery systems with/without monitoring the individual luminaires or for connection to an emergency mains for identifying and illuminating escape routes. Type Article no.. Lamps/ Weight Watts approx. kg 1) with electronic ballast (EVG) KL EVG x T 16/8 W 1, KL EVG x TC-SEL 11 W 1, KL EVG x TC-L 18 W 1,2 with high bay reflector (SB) and electronic ballast (EVG) KL SB EVG x T 16/8 W 1, KL SB EVG x TC-SEL 11 W 1, KL SB EVG x TC-L 18 W 1,3 with low bay reflector (ST) and electronic ballast (EVG) KL ST EVG x T 16/8 W 1, KL ST EVG x TC-SEL 11 W 1, KL ST EVG x TC-L 18 W 1,3 NEW Mechanical Data: Types...S. = with high or low bay reflector. Electrical Data: With electronic ballast (230V AC / DC) W KL LED x LED 1 W 1,1 1) Weights without packing material Series KL with legend! Further series / equipment for series KL B/D only: -.../P button for testing the emergency light function for series KL B. and KL D. EVG: -.../MA automatic monitoring the emergency light fitting with weekly functioning test and indication of the test results by LED (luminescence diode) at the luminaire. for series KL EVG only: - with electronic ballast (EVG) for the following voltages: 110 V DC, 24V DC, 12V DC - with separate or integrated monitoring module for connection to group or central battery systems with device for monitoring each individual luminaire. (For any inquiry please indicate the make of the equipment used.) For further equipment please see catalogue section Dustproof / Waterproof luminaires of series 163 / KL Self adhesive legends green/white 1) 121/33 W 121/34 W 121/35 W for clear stippled or clear covers for escape route identification acc. to BGV A8 and DIN Sighting distance acc. to EN 1838 and DIN 4844 = 30m. 1) not for white opalescent covers Accessories / Spare Parts Type Article no. Spare glasses W K PC K PC Brackets WA WA DA /33 W /34 W /35 W PMMA clear stippled PMMA white opalescent PMMA clear PC clear stippled PC clear wall bracket 45 wall bracket 90 ceiling bracket Standard legends, self adhesive (for clear stippled or clear light fittings) emergency exit left emergency exit right emergency exit below Further legends and wordings upon request. For further accessories and spare parts please see catalogue section Dustproof / Waterproof luminaires of series KL When ordering any electronic components or battery sets please do always indicate the type nos. of the light fittings. Emergency Notleuchten Light Fittings 207 Bitte beachten Sie die Hinweise Subject im to Technischen technical changes Anhang!

9 Small shock resistant Emergency/Escape Sign Light Fittings Series B/D At working places and meeting places, humid and wet rooms, for illuminating and indicating escape routes. Mechanical Data: Housing: White polycarbonate. Diffuser: Injected, clear polycarbonate with internal prisms or white opalescent (W). Multiple hinge at one small side for suspending and unhinging purpose. Captive stainless steel screw on the other side for closing the fitting. Connection: 3- / 4-pole terminal. Cable entries: 1 plug M20 at each of the small sides. Mounting system: 2 points at the upper side of the housing for direct ceiling mounting; rubber gaskets and washers inside the fitting. Wiring diagram D/B maintained/stand-by light switch Wiring diagram B stand-by Electrical Data: (series B/D only) NiCd battery set - gastight - mounted on the reflector. The battery set is constantly charged and therefore ready for operation at any time. Visual monitoring of the battery charging process by LED (luminescence diode). Electronic deep discharge protection. Re-charging time: 24 hours acc. to EN Baureihe LED: 2 x 1W LUXEON Highpower-LED NiMH-Batterie Modes of functioning:... B = stand-by operation = in case of mains failure the lamp is on.... D = maintained operation = in case of mains failure the lamp is switched over to battery operation.... MA = automatic monitoring the emergency light fitting with weekly functioning test and indication of the test results by LED (luminescence diode) at the luminaire. Connection voltage: 230V, 50Hz (standard) Ambient temperatures: -5 C up to +30 C (maintained version) -5 C up to +40 C (stand-by version) B/D IP65 with battery set T 16 TC - L Type Article. Lamps/ Em.- Flux factor Weight no. Watts hours appr.% 2) kg 4) Starting: Connect battery conductor Out of operation: Disconnect battery conductor Stand-by operation: Do not connect L1' /.. B. maintained and stand-by version 1) /45 W B/D x T 16/8 W , /36 W B/D x T 16/8 W ,3 Shock resistance test: RK 1.0 / 10A NEW LED stand-by version /39 W B x TC-L 18 W ,3 stand-by version with automatic monitoring system /17 W B1 MA x TC-L 18 W , /17 W B3 MA x TC-L 18 W , /39 W B1 MA x TC-L 18 W ,3 maintained version with electronic ballast (EVG) and automatic monitoring system /45 W D1 EVG MA x T 16/8 W ,2 1) Wiring uncompensated only 2) Ratio effective lamp flux/nominal flux 3) Also available with MA 4) Weights without packing material IP65 with battery set Type Article. Lamps/ Em.- Flux factor Weight no. Watts hours appr.% 2) kg 4) W LED/1 MA x LED 1 W , W LED/3 MA x LED 1 W ,0 Bitte Subject beachten to technical Sie die changes Hinweise im Technischen Anhang! 208

10 ! EVG for connection to central power supply unit T 16 TC-SEL TC- L LED For connection to group or central battery systems or to emergency mains for illuminating escape routes or for emergency illumination on ships, vehicles etc LL EVG x T 16/8 W W 0, EVG x TC-SEL 11 W 0, EVG x TC-L 18 W 0, EVG 24V DC x TC-SEL 11W 1, EVG 12V DC x TC-SEL 11W 1,0 NEW Type Article no. Lamps/ Weight Watts approx. kg 1 with electronic ballast (EVG) W LED x LED 1W 1,0 1) Weights without packing material Further series / equipment for series B/D only:... P button for testing the emergency light function... EVG with electronic ballast Special version for wind power stations (Please ask for our special data sheet). IP65 Electrical Data: Electronic ballasts (230V AC / DC, 110V DC, 24V DC or 12V DC). A double lamp luminaire will be equipped with 2 electronic ballasts, separate lamp circuits and separate connection terminals. for series EVG only: with conventional ballast 230V, 50Hz with separate or integrated monitoring module for connection to group or central battery systems with device for monitoring each individual luminaire. (For any inquiry please indicate the make of the equipment used.) For further equipment please see catalogue section Dustproof / Waterproof luminaires of series 130 / 131 / Type with standard legend Self adhesive legends for escape route identification acc. to BGV A8 and DIN Sighting distance acc. to EN 1838 and DIN 4844 = 15m. Accessories / Spare Parts Type Article no. Standard legend, self adhesive 265/76/ Note: Further legends and wordings upon request. Emergency Notleuchten Light Fittings For further accessories and spare parts please see catalogue section Dustproof / Waterproof luminaires of series 130/131/ When ordering any electronic components or battery sets please indicate the type nos. of the light fittings. 209 Bitte beachten Sie die Hinweise Subject im to Technischen technical changes Anhang!

11 Dustproof/Waterproof Polyester Emergency Light Fittings of Insulation Class II - without diffuser Series For illumination of working places and acc. to DIN VDE 0108 for illuminating and identifying escape routes etc. Mechanical Data: Housing: Glass fibre reinforced polyester resin. Gasket: Weatherproof, non-ageing and chemically resistant profile gasket. Electrical components: Mounted on the inner side of the suspended polyester lid. Starter easily accessible from outside the fitting. Moisture-proof lampholders with rotating contact system, neoprene gasket. Cable entries: At the small front sides and at the upper side of the housing, also for looping the mains cable at one side. 2 plugs M20. Connection: 3-pole connection terminal. Through wiring system: Up to 5 x 2,5mm 2 possible, at extra charge. Mounting system: Closed knock-outs for direct ceiling mounting; rubber gaskets and washers inside the fitting. Wiring diagram maintained operation light switch Wiring diagram maintained operation Electrical Data: (series175...only) Incorporated NiCd battery set which is constantly charged and therefore ready for operation at any time. Visual monitoring the battery charging process by LED (luminescence diode). Electronic deep discharge protection. Re-charging time: 24 hours acc. to EN Luminous flux raising i.e. initially the emergency lamp has got a higher luminous flux. Only one lamp is operating in the emergency case. Modes of functioning: Maintained operation = in case of mains failure 1 lamp is switched over to battery operation. Connection voltage: 230V, 50Hz (standard) Ambient temperatures: -5 C up to +30 C (maintained version) -5 C up to +40 C (stand-by version) light switch Starting: Connect battery conductor Out of operation: Disconnect battery conductor Stand-by operation: Do not connect L1' Series Series with battery set T 26 Type Article no. Lamps/ Flux factor Weight Watts approx. % 2) approx. kg 3) 1 hour emergency operation, with conventional ballast IP /../ /18/1 3) ) 1 x T 26/36 W 18 2, /15/1 3) ) 1 x T 26/58 W 15 3, /18/ ) 2 x T 26/36 W 18 4, /15/ ) 2 x T 26/58 W 15 5,7 1 hour emergency operation, with electronic ballast (EVG) /18/1 EVG 3) x T 26/36 W 18 2, /15/1 EVG 3) x T 26/58 W 15 2, /18/1 EVG 3) x T 26/36 W 18 3, /15/1 EVG 3) x T 26/58 W 15 2,6 1) Wiring uncompensated only 3) Weights without packing material 2) Ratio effective lamp flux/nominal flux Bitte Subject beachten to technical Sie die changes Hinweise im Technischen Anhang! 210

12 EVG for connection to central power supply unit For connection to group or central battery systems or to an emergency mains for illuminating escape routes, ships or vehicles etc. IP65 Electrical design: Electronic ballast (230V AC / DC, 110V DC, 24V DC). A double lamp luminaire will be equipped with 2 electronic ballasts, separate lamp circuits and separate connection terminals.! EVG T 26 Type Article no. Lamps/ Weight Watts approx. kg 1 with electronic ballast (EVG) EVG 1) x T 26/18 W 0, EVG x T 26/36 W 1, EVG x T 26/58 W 1,6 with 2 individual electronic ballasts (EVG/2) EVG/ x T 26/36 W 1, EVG/ x T 26/58 W 1,8 1) Weights without packing material Further series / equipment for series /.../. only:.../b stand-by system = emergency lighting only in case of mains failure.../3 3 hour emergency operation for series /../. EVG only:.../ma automatic self-monitoring and indication of the results, weekly functioning test and yearly long-time test acc. to DIN VDE for series EVG only: with separate or integrated monitoring module for connection to group or central battery equipment with system for monitoring each individual luminaire. (For any inquiry please indicate the make of the used equipment.). with electronic ballast for special voltages: 110V DC, 24V DC with conventional ballast 230V, 50 Hz for both series: with external reflectors with rotable snap-on reflectors with protective tube S38 or S50 with oval-shaped protective tube S0 also in FF version with through wiring system up to 5x2,5mm 2 with different cable entries up to M25 x 1,5 for fluo tubes of 38mm Ø (with enlargement rings 1681/38) Emergency Notleuchten Light Fittings Accessories / Spare Parts For accessories and spare parts please see catalogue section Dustproof / Waterproof luminaires of series When ordering any electronic components or battery sets please do always indicate the type nos. of the light fittings. 211 Bitte beachten Sie die Hinweise Subject im to Technischen technical changes Anhang!

13 NEW IP40 T x 321 x 77 (102*) x 321 x 77 (102*) (* bei Pendel-, Wandausleger- bzw. Deckenauslegermontage) /3 D1 EVG m 1 x T 16/8 W /3 D3 EVG m 1 x T 16/8 W /7 D1 EVG m 1 x T 16/8 W /7 D3 EVG m 1 x T 16/8 W Bitte Subject beachten to technical Sie die changes Hinweise im Technischen Anhang! 212

14 IP40 T 16 TC-SEL /1 EVG m 1 x T 16/6 W 1, /1 EVG m 1 x TC-SEL 9 W 1, /3 EVG m 1 x T 16/8 W 1, /3 EVG m 1 x TC-SEL 11 W 1, /7 EVG m 1 x T 16/8 W 1, /7 EVG m 1 x TC-SEL 11 W 1,6! Weitere Baureihen / Ausführungen Emergency Notleuchten Light Fittings.../33.../34.../33.../34.../35.../35.../99.../98.../ Bitte beachten Sie die Hinweise im Technischen Anhang!

15 NEW Emergency Light Power Supply Unit Series N As power supply for light fittings with up to 200W which are installed separately from the "N"-device in a different room. It is especially recommended in cases in which the existing environmental conditions prohibit the use of fittings with individual battery sets. Mechanical design: Housing: Polycarbonate, grey (RAL 9006) Battery and electronic device: Each in a separate housing acc. to DIN EN Battery compartment with aeration opening Mounting: Direct wall mounting (borings of Ø 6.0 mm) Installation: Plug-type terminals (up to 2.5mm²) Admissible ambient temperature: -5 C up to +35 C Insulation class: I Attention: Installation of this power supply unit is allowed outside the hazardous area only. Distance between the light fitting and the "N" unit: 500m max.voltage drop to be considered acc. to VDE Wiring diagrams for electronic ballast types: mains unswitched mains switched ligh fittings output interface control input stand by Electrical design: Emergency power supply unit with battery for operating 1 or 2 fluorescent light fittings with electronic ballast (EVG) Emergency light electronic device with deep discharge protection and switchover system for mains/emergency operation As a standard with self monitoring device, performing automatic weekly functional and annual operating period tests. The consumer loads will be monitored by a self- adjusting performance control device. Manual actuation of the functional tests and display of messages and malfunctions via a combined foil touch screen. Interface for remote controlling the operating state via external switch. Interface for malfunction indication Battery set: With maintenance-free lead-battery Modes of operation: Maintained or stand-by operation Maintained operation: Switching to battery operation in case of mains failure. Stand-by operation: Emergency lamp switches on in case of mains failure only. Rated voltage: 230V / 50Hz Suitable for: Fluorescent light fittings with electronic ballast (EVG): For double lamp fittings with double EVG, please consider double consumption or use fittings with 2 EVGs (separating the systems) Note: The EVGs in the light fittings connected to the power supply unit must be suitable for DC and AC operation and for application in an equipment acc. to DIN VDE Light fittings for incandescent lamps. Admissible consumption acc. to the admissible consumption of the fluorescent tubes. N12/... 18Ah N12/... 45Ah N with separate housing each for the inverter and for the battery set inverter IP65 IP54 batterie set IP32 N12/... 12/24Ah N12/... 90Ah Type Article no. Lamps/ Flux factor Weight Watts approx.% 1) appr. kg 2 for light fittings with electronic ballast (EVG)- 1 hour operating N12/118-58/12/1 DC x W 100 7,1 N12/218-36/18/1 DC x W 100 8,8 N12/258/24/1 DC x 58 W ,8 for light fittings with electronic ballast (EVG)- 3 hours operating N12/118-58/45/3 DC x W ,2 N12/218-36/45/3 DC x W ,2 N12/258/90/3 DC x 58 W ,5 1) Ratio effective flux/rated lamp flux 2) Weights without packing material Emergency Light Fittings! Further series / equipment Special version for operating fittings with conventional ballasts with electronic starter with a DC/AC converter which will provide a cascaded 230V / 50Hz AC supply with 80VA. Bitte Subject beachten to technical Sie die changes Hinweise im Technischen Anhang! 214

16 Elektroniks chrank IP54 Batterieschrank IP32 Emergency Notleuchten Light Fittings 215 Bitte beachten Sie die Hinweise Subject im to Technischen technical changes Anhang!

17 Elektroniks chrank IP54 Batterieschrank IP32 Bitte Subject beachten to technical Sie die changes Hinweise im Technischen Anhang! 216

18 Emergency Notleuchten Light Fittings 217 Bitte beachten Sie die Hinweise Subject im to Technischen technical changes Anhang!