Code Reference Competitive Comparison

Transcription

1 Code Reference Competitive Comparison Product Selection Guide Water Tempering Valves LavSafe L111, MMV 1170, L1170 USG-B w a t t s. c o m

2 Table of Contents PAGE Code Reference Guide International Plumbing Code (IPC) - Tempering Valves International Residential Code (IRC) - Tempering Valves Uniform Plumbing Code (UPC) - Tempering Valves Product Selection Guide for ASSE 1017, 1069 & for ASSE for ASSE

3 Watts Code Reference Guide International Plumbing Code (IPC) - Tempering Valves Application Watts Listed Products IPC IPC IPC State Adoption By Series CT, KS, MO, NY, VT AR, AZ, CO, DC, FL, GA, ID, MI, MS, NC, ND, OH, SC, UT AL, DE, MD, NH, OK, PA, RI, UT, VA, WV Public Lavatories USG-B, MMV, L111, LavSafe No reference to tempering valves or ASSE standards Tempered water for public hand-washing facilities. Tempered water shall be delivered from public hand-washing facilities through an approved water temperature limiting device that conforms to ASSE Bathtubs and Whirlpools MMV, L111 No reference to tempering valves or ASSE standards Bathtub and whirlpool bathtub valves. The hot water supplied to bathtubs and whirlpool bathtubs shall be limited to a maximum temperature of 120 F (49 C) by water temperature limiting device that conforms to ASSE 1070, except where such protection is otherwise provided by a combination tub/shower valve in accordance with section Tempered water for public hand-washing facilities. Tempered water shall be delivered from public hand-washing facilities. Tempered water shall be delivered through an approved water temperature limiting device that conforms to ASSE 1070 or CSA B Bathtub and whirlpool bathtub valves. The hot water supplied to bathtubs and whirlpool bathtubs shall be limited to a maximum temperature of 120 F (49 C) by water temperature limiting device that conforms to ASSE 1070 or CSA B125.3, except where such protection is otherwise provided by a combination tub/shower valve in accordance with section Shower and Tub-Shower E800SG, E800MSG (WBT) Shower valves. Shower and tub-shower combination valves shall be balanced pressure, thermostatic or combination balanced-pressure/thermostatic valves that conform to the requirements of ASSE 1016 or CSA B125. Gang Showers MMV, L Shower valves (cont'd). Multiple (gang) showers supplied with a single tempered water supply pipe shall have the water supply for such showers controlled by a master thermostatic mixing valve complying with ASSE Shower and tub-shower combination valves and master thermostatic mixing valves required by this section shall be equipped with a means to limit the maximum setting of the valve to 120 F (49 C), which shall be field adjusted in accordance with the manufacturer's instructions Individual shower valves. Individual shower valves and tub-shower combinations valves shall be balanced-pressure, thermostatic or combination balanced-pressure/thermostatic valves that conform to the requirements of ASSE 1016 or CSA B125 and shall be installed at the point-of-use. Shower and tub-shower combination valves required by this section shall be equipped with a means to limit the maximum setting of the valve to 120 F (49 C), which shall be filed adjusted in accordance with the manufacturer's instructions. In-line thermostatic valves shall not be utilized for compliance with this section Multiple (gang) showers. Multiple (gang) showers supplied with a singletempered water supply pipe shall have the water supply for such showers controlled by an approved automatic temperature control mixing valves that conforms to ASSE 1069 or CSA B125, or each shower head shall be individually controlled by a balanced-pressure/thermostatic valve that conforms to ASSE 1016 or CSA B125 and is installed at the point-of-use. Such valves shall be equipped with a means to limit the maximum setting of the valve to 120 F (49 C), which shall be field adjusted in accordance with the manufacturer's instructions Individual shower valves. Individual shower valves and tub-shower combinations valves shall be balanced-pressure, thermostatic or combination balanced-pressure/thermostatic valves that conform to the requirements of ASSE 1016 or CSA B125.1 and shall be installed at the point-of-use. Shower and tub-shower combination valves required by this section shall be equipped with a means to limit the maximum setting of the valve to 120 F (49 C), which shall be filed adjusted in accordance with the manufacturer's instructions. In-line thermostatic valves shall not be utilized for compliance with this section Multiple (gang) showers. Multiple (gang) showers supplied with a single-tempered water supply pipe shall have the water supply for such showers controlled by an approved automatic temperature control mixing valves that conforms to ASSE 1069 or CSA B125, or each shower head shall be individually controlled by a balanced-pressure/thermostatic valve that conforms to ASSE 1016 or CSA B125 and is installed at the point-of-use. Such valves shall be equipped with a means to limit the maximum setting of the valve to 120 F (49 C), which shall be field adjusted in accordance with the manufacturer's instructions. Temperature-Actuated Flow Reduction WHT Temperature-actuated, flow reduction valves for individual fixture fittings. Temperature-actuated, flow reduction devices, where installed for individual fixture fittings, shall conform to ASSE Such valves shall not be used alone as a substitute for the balanced pressure, thermostatic or combination shower valves required in Section Temperature-actuated, flow reduction valves for individual fixture fittings. Temperature-actuated, flow reduction devices, where installed for individual fixture fittings, shall conform to ASSE Such valves shall not be used alone as a substitute for the balanced pressure, thermostatic or combination shower valves required in Section Temperature-actuated, flow reduction valves for individual fixture fittings. Temperature-actuated, flow reduction devices, where installed for individual fixture fittings, shall conform to ASSE Such valves shall not be used alone as a substitute for the balanced pressure, thermostatic or combination shower valves required in Section Bidet MMV, L111 No reference to tempering valves or ASSE standards Bidet water temperature. The discharge water temperature from a bidet fitting shall be limited to a maximum temperature of 110 F (43 C) by a water temperature limiting device conforming to ASSE Bidet water temperature. The discharge water temperature from a bidet fitting shall be limited to a maximum temperature of 110 F (43 C) by a water temperature limiting device conforming to ASSE Water Heater 1170, MMV, N170-M Water heater as space heater. Where a combination potable water heating and space heating system requires water for space heating at temperatures higher than 140 F (60 C), a master thermostatic mixing valve complying with ASSE 1017 shall be provided to limit the water supplied to the potable hot water distribution system to a temperature of 140 F (60 C) or less. The potability of the water shall be maintained throughout the system. Tankless Heaters 1170, MMV, N170-M Water temperature control in piping from tankless heaters. The temperature of water from tankless water heaters shall be a maximum of 140 F (60 C) when intended for domestic uses. This provision shall not supersede the requirement for protective shower valves in accordance with Section Water heater as space heater. Where a combination potable water heating and space heating system requires water for space heating at temperatures higher than 140 F (60 C), a master thermostatic mixing valve complying with ASSE 1017 shall be provided to limit the water supplied to the potable hot water distribution system to a temperature of 140 F (60 C) or less. The potability of the water shall be maintained throughout the system Water temperature control in piping from tankless heaters. The temperature of water from tankless water heaters shall be a maximum of 140 F (60 C) when intended for domestic use This provision shall not supersede the requirement for protective shower valves in accordance with Section Water heater as space heater. Where a combination potable water heating and space heating system requires water for space heating at temperatures higher than 140 F (60 C), a master thermostatic mixing valve complying with ASSE 1017 shall be provided to limit the water supplied to the potable hot water distribution system to a temperature of 140 F (60 C) or less. The potability of the water shall be maintained throughout the system Water temperature control in piping from tankless heaters. The temperature of water from tankless water heaters shall be a maximum of 140 F (60 C) when intended for domestic use. This provision shall not supersede the requirement for protective shower valves in accordance with Section Temperature-Actuated Mixing Valves 1170, MMV, N170-M Temperature-actuated mixing valves. Temperature-actuated mixing valves, which are installed to reduce water temperatures to defined limits, shall comply with ASSE Temperature-actuated mixing valves. Temperature-actuated mixing valves which are installed to reduce water temperatures to defined limits, shall comply with ASSE Temperature-actuated mixing valves. Temperature-actuated mixing valves which are installed to reduce water temperatures to defined limits, shall comply with ASSE Hot Water Supply System 1170, MMV, N170-M Where required. In nonresidential occupancies, hot water or tempered water shall be supplied for bathing and washing purposes. Tempered water shall be delivered from accessible hand-washing facilities Where required. In nonresidential occupancies, tempered water shall be supplied through a water temperature limiting device that conforms to ASSE 1070 and shall limit the tempered water to a maximum of 110 F (43 C). This provision shall not supersede the requirement for protective shower valves in accordance with Section Where required. In nonresidential occupancies, hot water shall be supplied for culinary purposes, cleansing, laundry or building maintenance purposes. Tempered water shall be supplied through a water temperature limiting device that conforms to ASSE 1070 and shall limit the tempered water to a maximum of 110 F (43 C). This provision shall not supersede the requirement for protective shower valves in accordance with Section

4 Watts Code Reference Guide International Residential Code (IRC) - Tempering Valves Application Watts Listed Products IRC IRC IRC State Adoption By Series CT, HI, IN, KS, MA, NY, VT AK, AR, DC, FL, GA, HI, ID, KY, LA, MI, MN, MS, MT, ND, NJ, NV, OH, OR, SC, WY CA, IA, MD, ME, NH, OK, PA, RI, TN, UT, VA, WA, WV Bathtubs and Whirlpools MMV, L111 P2713 Bathtubs and P2720 Whirlpool Tubs (tempering not addressed) P Bathtub and whirlpool bathtub valves. The hot water supplied to bathtubs and whirlpool bathtubs shall be limited to a maximum temperature of 120 F (49 C) by a water temperature-limiting device that conforms to ASSE 1070, except where such protection is otherwise provided by a combination tub/ shower valve in accordance with Section P P Bathtub and whirlpool bathtub valves. The hot water supplied to bathtubs and whirlpool bathtubs shall be limited to a maximum temperature of 120 F (49 C) by a water temperature-limiting device that conforms to ASSE 1070, except where such protection is otherwise provided by a combination tub/shower valve in accordance with Section P Shower and Tub-Shower E800SG, E800MSG (WBT) P Shower control valves. Shower and tub/shower combination valves shall be equipped with control valves of the pressure balance, thermostatic mixing or combination pressure balance/thermostatic mixing valve types with a high limit stop in accordance with ASSE 1016 or CSA B125. The high limit stop shall be set to limit water temperature to a maximum of 120 F (49 C). P Shower control valves. Shower and tub/shower combination valves shall be equipped with control valves of the pressure balance, thermostatic mixing or combination pressure balance/thermostatic mixing valve types with a high limit stop in accordance with ASSE 1016 or CSA B125. The high limit stop shall be set to limit water temperature to a maximum of 120 F (49 C). In-line thermostatic valves shall not be used for compliance with this section. P Shower control valves. Shower and tub/shower combination valves shall be equipped with control valves of the pressure balance, thermostatic mixing or combination pressure balance/thermostatic mixing valve types with a high limit stop in accordance with ASSE 1016 or CSA B125. The high limit stop shall be set to limit water temperature to a maximum of 120 F (49 C). In-line thermostatic valves shall not be used for compliance with this section. Bidet MMV, L111 P2721 Bidet Installations (tempering not addressed) P Bidet water temperature. The discharge water temperature from a bidet fitting shall be limited to a maximum temperature of 110 F (43 C) by a water temperature-limiting device that conforms to ASSE P Bidet water temperature. The discharge water temperature from a bidet fitting shall be limited to a maximum temperature of 110 F (43 C) by a water temperature-limiting device that conforms to ASSE Water Heater 1170, MMV, N170-M3 P Temperature control. Where a combination water heater-space heating system requires water for space heating at temperatures exceeding 140 F (60 C), a master thermostatic mixing valve complying with ASSE 1017 shall be installed to temper the water to a temperature of 140 F (60 C) or less for domestic uses. P Scald Protection. Where a combination water heater-space heating system requires water for space heating at temperatures exceeding 140 F (60 C), a means such as a mixing valve shall be installed to temper water for domestic uses. P Temperature control. Where a combination water heater-space heating system requires water for space heating at temperatures exceeding 140 F (60 C), a master thermostatic mixing valve complying with ASSE 1017 shall be installed to temper the water to a temperature of 140 F (60 C) or less for domestic uses. P Temperature control. Where a combination water heater-space heating system requires water for space heating at temperatures exceeding 140 F (60 C), a master thermostatic mixing valve complying with ASSE 1017 shall be installed to temper the water to a temperature of 140 F (60 C) or less for domestic uses. 4 5

5 Watts Code Reference Guide Uniform Plumbing Code (UPC) - Tempering Valves Application Watts Listed Products UPC UPC UPC State Adoption By Series AK, ID, NV, SD CA, HI, MT, NM, OR, Houston, Topeka IA, WA, St. Louis (CA, ID, MT to adopt 2009) Public Lavatories USG-B, MMV, L111, LavSafe Limitation of Hot Water Temperature for Public Lavatories. Hot water delivered for public-use lavatories shall be limited to a maximum temperature of 120 F (49 C). The water heater thermostat shall not be considered a control for meeting this provision Limitation of Hot Water Temperature for Public Lavatories. Hot water delivered for public-use lavatories shall be limited to a maximum temperature of 120 F (49 C). The water heater thermostat shall not be considered a control for meeting this provision Limitation of Hot Water Temperature for Public Lavatories. Hot water delivered for public-use lavatories shall be limited to a maximum temperature of 120 F (49 C) by a device that conforms to ASSE 1070 or CSAB The water heater thermostat shall not be considered a control for meeting this provision. Bathtubs and Whirlpools MMV, L Whirlpool Bathtubs (tempering not addressed) Limitation of Hot Water in Bathtubs. The maximum hot water temperature discharging from the bathtub filler shall be 120 F (49 C) Limitations of Hot Water in Bathtubs and Whirlpool Bathtubs. The maximum hot water temperature discharging from the bathtub and whirlpool bathtub filler shall be limited to 120 F (49 C). The water heater thermostat shall not be considered a control for meeting this provision Limitations of Hot Water in Bathtubs and Whirlpool Bathtubs. The maximum hot water temperature discharging from the bathtub and whirlpool bathtub filler shall be limited to 120 F (49 C) by a device that conforms to ASSE 1070 or CSA B The water heater thermostat shall not be considered a control for meeting this provision. Shower and Tub-Shower E800SG, E800MSG (WBT) Shower and Tub-Shower Combinations Showers and tub-shower combinations in all buildings shall be provided with individual control valves of the pressure balance, thermostatic, or combination pressure balance / thermostatic mixing valve type that provide scald and thermal shock protection. These valves shall conform to ASSE Shower and Tub-Shower Combination Control Valves. Showers and tub-shower combinations in all buildings shall be provided with individual control valves of the pressure balance, thermostatic, or combination pressure balance / thermostatic mixing valve type that provide scald and thermal shock protection. These valves shall conform to ASSE Shower and Tub-Shower Combination Control Valves. Showers and tubshower combinations in all buildings shall be provided with individual control valves of the pressure balance, thermostatic, or combination pressure balance / thermostatic mixing valve type that provide scald and thermal shock protection. These valves shall conform to ASSE Gang Showers MMV, L (cont'd)...gang showers, when supplied with a single temperaturecontrolled water supply pipe, may be controlled by a master thermostatic mixing valve in lieu of individually controlled pressure balance, thermostatic, or combination pressure balance/thermostatic mixing valves. Handle position stops shall be provided on such valves and shall be adjusted per the manufacturer's instructions to deliver a maximum mixed water setting of 120 F (49 C). The water heater thermostat shall not be considered a suitable control for meeting this provision (cont'd)...gang showers, when supplied with a single temperature-controlled water supply pipe, may be controlled by a master thermostatic mixing valve in lieu of individually controlled pressure balance, thermostatic, or combination pressure balance/thermostatic mixing valves. Handle position stops shall be provided on such valves and shall be adjusted per the manufacturer's instructions to deliver a maximum mixed water setting of 120 F (49 C). The water heater thermostat shall not be considered a suitable control for meeting this provision (cont'd)...gang showers, when supplied with a single temperature-controlled water supply pipe, shall be controlled by a mixing valve that conforms to ASSE Handle position stops shall be provided on such valves and shall be adjusted per the manufacturer's instructions to deliver a maximum mixed water setting of 120 F (49 C). The water heater thermostat shall not be considered a suitable control for meeting this provision. Bidet MMV, L Bidets (tempering not addressed) (tempering not addressed) Limitation of Water Temperature in Bidets. The maximum hot water temperature discharging from a bidet shall be limited to 110 F (43 C) by a device that conforms to ASSE 1070 or CSA B125.3.The water heater thermostat shall not be considered a suitable control for meeting this provision. Water Heater 1170, MMV, N170-M Temperature-Limiting Devices. A water heater installation or hot water storage vessel installation shall be provided with over-temperature protection by means of an approved, listed device installed in accordance with the terms of its listing and the manufacturer's instructions Temperature-Limiting Devices. A water heater installation or hot water storage vessel installation shall be provided with over-temperature protection by means of an approved, listed device installed in accordance with the terms of its listing and the manufacturers instructions Temperature-Limiting Devices. A water heater installation or hot water storage vessel installation shall be provided with over-temperature protection by means of an approved, listed device installed in accordance with the terms of its listing and the manufacturers instructions. Temperature Actuated Mixing Valves 1170, MMV, N170-M3 Table 14-1 Referenced Standards. ASSE referenced. Table 14-1 Referenced Standards. ASSE referenced. Table 14-1 Referenced Standards. ASSE referenced. Hot Water Supply System 1170, MMV, N170-M3 Table 14-1 Referenced Standards. ASSE referenced. Table 14-1 Referenced Standards. ASSE referenced. Table 14-1 Referenced Standards. ASSE referenced. 6 7

6 Product Selection Guide Honeywell Zurn/Wilkins Conbraco/Apollo Reliance/Cash Acme Symmons Caleffi Leonard Point-of-Use/Source for ASSE 1017, 1069 & 1070 MMV AM ZW B - MVB Heatguard 160 Aqualine , 370 ASSE Standard Listing 1017, 1069, , , , , , psid 1 2" " " not available 13 not available Minimum Stated Flow 0.5 gpm 0.5 gpm 0.5 gpm 1.0 gpm 1.0 gpm 0.5 gpm 1.0 gpm 0.5 gpm Outlet Temperature Range F F F F F F F not stated Cold Water Inlet Temperature F not stated F F F F F not stated Hot Water Inlet Temperature max. 200 F max. 212 F F F max. 195 F F F max. 200 F Maximum Working Pressure 150 psi 150 psi 145 psi 150 psi 145 psi 150 psi 140 psi 125 psi Approach Temperature (outlet maximum within F of inlet HW supply) 5 F 3 F not stated 5 F not stated 10 F 9 F 5 F Lockable Temperature Setting Yes Yes Yes Yes Yes Yes Yes Standard Unions Order Separate Yes Yes Order Separate Yes Yes No Standard Checks Order Separate Yes Yes Order Separate Yes Yes Yes Lead Free* No Yes Yes No No Yes Yes Standard Filters No No Yes Order Separate Yes No No Connection Type Threaded Yes Yes Yes Yes Yes Yes Yes - MIPS Sweat Yes Yes Yes Yes Yes Yes Yes CPVC Yes Yes Yes Yes No NO No PEX Yes Yes Yes Yes Yes No No Quick Connect No No No Yes No No No Competitive Data Taken From Manufacturer Sales Literature BAA/ARRA Compliant 22-Sep-10 *The wetted surface of this product contacted by consumable water contains less than one quarter of one percent (0.25%) of lead by weight. 8 9

7 Product Selection Guide Point-of-Use for ASSE 1070 Honeywell Zurn/Wilkins Conbraco/Apollo Reliance/Cash Acme Symmons Leonard USG-B LavSafe UMV ZW3870T 34D - MVD Heatguard CK 170 ASSE Standard Listing , psid 2.5 gpm 2.2 gpm 3.0 gpm 3.0 gpm 3.5 gpm 4.5 gpm 5.0 gpm 4.5 gpm Minimum Stated Flow 0.5 gpm 0.5 gpm 0.5 gpm 0.5 gpm 0.5 gpm 0.5 gpm 0.5 gpm 0.5 gpm Outlet Temperature Range F F F F F F F not stated Cold Water Inlet Temperature F F not stated F not stated F F not stated Hot Water Inlet Temperature F F max. 180 F F max. 210 F max. 195 F F max. 212 F Maximum Working Pressure 150 psi 125 psi 150 psi 145 psi 125 psi 145 psi 125 psi 125 psi Approach Temperature (outlet maximum within F of inlet HW supply) 5 F 5 F 15 F not stated not stated not stated 10 F 5 F Lead Free* No Yes Yes No No Yes WaterSense n/a n/a n/a n/a n/a n/a n/a Lockable Temperature Setting Yes Yes Yes Yes Yes Yes Integrated 4-port Configuration w/internal Cold Water Bypass n/a No - Add on No No No No No - 4th optional Standard Checks Yes Yes Yes Yes Yes Yes Standard Filters No No No No Yes No - 4th optional Connection Type 3/8" Compression 3/8" Compression 3/8" Compression 3/8" Compression 3/8" Compression 3/8" Compression 3/8" Compression 3/8" Compression Competitive Data Taken From Manufacturer Sales Literature BAA/ARRA Compliant BAA/ARRA Compliant 22-Sep-10 *The wetted surface of this product contacted by consumable water contains less than one quarter of one percent (0.25%) of lead by weight

8 Product Selection Guide Honeywell Zurn/Wilkins Conbraco/Apollo Reliance/Cash Acme Symmons Caleffi Leonard Point-of-Source for ASSE , L1170 AM-1 ZW A - MVA 110-D 110-HX 115-D 115-H 5-120, 5-130, Aqualine , 370 ASSE Standard Listing , , psid 1 2" not available not available not stated " not stated " not stated not available 20 not available Minimum Stated Flow 0.5 gpm 0.5 gpm 0.5 gpm 0.5 gpm 1.0 gpm 1.0 gpm 2.5 gpm 2.5 gpm not stated 0.5 gpm not stated 0.5 gpm Outlet Temp. Range Standard F F F F F F F F F F F not stated Low F F F F not stated Cold Water Inlet Temperature F not stated F F F F F F F F not stated max. 200 F Hot Water Inlet Temperature max. 200 F max. 212 F F max. 210 F max. 195 F F F max. 200 F 125 psi Maximum Working Pressure 150 psi 150 psi 145 psi 150 psi 145 psi 125 psi 150 psi 200 psi 5 F Approach Temperature (outlet maximum within F of inlet HW supply) 5 F not stated not stated not stated not stated 10 F 10 F 27 F Yes Lead Free* No Yes Yes No No No Yes Yes Lockable Temperature Setting Yes Yes Yes Yes Yes Yes Yes No Standard Unions Order Separate Yes Yes Order Separate No Yes Yes Yes Standard Checks Order Separate Yes Yes Order Separate No Yes Yes No Standard Filters No No Yes Order Separate No Yes No Yes - MIPS Connection Type Threaded Yes Yes Yes Yes* Yes* Yes Yes Yes Yes Yes Yes Sweat Yes Yes Yes Yes Yes Yes Yes No Yes Yes No CPVC Yes Yes Yes Yes* Yes* Yes Yes No No No No PEX Yes Yes Yes Yes Yes Yes Yes No Yes No No Quick Connect No No No Yes* Yes* Yes Yes No No No No Competitive Data Taken From Manufacturer Sales Literature BAA/ARRA Compliant *only available in 1/2 & 3/4 22-Sep-10 *The wetted surface of this product contacted by consumable water contains less than one quarter of one percent (0.25%) of lead by weight

9 For Technical Assistance Call Your Authorized Watts Representative. Telephone Headquarters: Watts Regulator Company 815 Chestnut St., North Andover, MA U.S.A North East Mid Atlantic Edwards, Platt & Deely, Inc. 277 Royal Ave., Hawthorne, NJ Edwards, Platt & Deely, Inc. 368 Wyandanch Ave., North Babylon, NY Vernon Bitzer Associates, Inc. 980 Thomas Drive, Warminster, PA W. P. Haney Company, Inc. 51 Norfolk Ave., South Easton, MA Disney McLane & Associates 428 McGregor Ave., Cincinnati, OH J. B. O Connor Company, Inc. P.O. Box 12927, Pittsburgh, PA [email protected] RMI 2533 Mechanicsville Tpk., Richmond, VA [email protected] The Joyce Agency, Inc Alban Rd., Springfield, VA [email protected] WMS Sales, Inc. (Main office) 9580 County Rd., Clarence Center, NY [email protected] South East Billingsley & Associates, Inc Crestview Ave., Kenner, LA [email protected] Billingsley & Associates, Inc. 478 Cheyenne Lane, Madison, MS [email protected] Francisco J. Ortiz & Co., Inc. Charlyn Industrial Pk., Road 190 KM1.9 - Lot #8, Carolina, Puerto Rico [email protected] Mid-America Marketing, Inc. 203 Industrial Drive, Birmingham, AL [email protected] Mid-America Marketing, Inc Grandview Avenue, Nashville, TN [email protected] Mid-America Marketing, Inc Old Hwy. 78, Memphis, TN [email protected] Smith & Stevenson Co., Inc Chastain Ave., Charlotte, NC [email protected] Harry Warren, Inc North Orange Blossom Trail, Orlando, FL [email protected] Watts Georgia 2861-B Bankers Industrial Drive, Atlanta, GA [email protected] North Central Canada Western South Central Dave Watson Associates 1325 West Beecher, Adrian, MI [email protected] Mid-Continent Marketing Services Ltd Lakeside Drive, Romeoville, IL [email protected] Soderholm & Associates, Inc rd Ave. N.W., Anoka, MN [email protected] Stickler & Associates 203 S. Curtis Road, Milwaukee, WI [email protected] Hugh M. Cunningham, Inc Benchmark, Dallas, TX [email protected] Sandia Group, Inc San Mateo #308, Albuquerque, NM [email protected] Mack McClain & Associates, Inc Meramec Bottom, Suite G, St. Louis, MO Mack McClain & Associates, Inc NE 69th Place, Ste. 56 Ankeny, IA [email protected] Mack McClain & Associates, Inc West 116th St., Olathe, KS [email protected] OK! Sales, Inc. 214 NE 12th. St., Ste A, Moore, OK [email protected] Delco Sales, Inc Raymer Ave., Fullerton, CA [email protected] Delco Sales, Inc. 111 Sand Island Access Rd., Unit I-4, Honolulu, HI [email protected] Fanning & Associates, Inc Franklin St., Denver, CO [email protected] Hollabaugh Brothers & Associates 6915 South 194th St., Kent, WA [email protected] Hollabaugh Brothers & Associates 3028 S.E. 17th Ave., Portland, OR [email protected] P I R Sales, Inc North San Marcos Place, Chandler, AZ [email protected] REPCOR 2455 Mercantile Drive, Ste.100, Rancho Cordova, CA [email protected] R. E. Fitzpatrick Sales, Inc West Nike Dr. (8250 South), West Jordan, UT [email protected] Watts Water Technologies (Canada) Inc North Service Road, Burlington, Ontario L7L 5H [email protected] Con-Cur West Marketing, Inc. 71B Clipper Street, Coquitlam, British Columbia V3K 6X [email protected] D.C. Sales Ltd. # th St. S.E., Calgary, Alberta T2H 2B [email protected] D.C. Sales Ltd Ave, Edmonton, Alberta T5M 2S [email protected] GTA Sales Team. Greater Toronto Area [email protected] Hydro-Mechanical Sales, Ltd Joseph Howe Drive, Suite 1, Halifax, Nova Scotia B3L 4H [email protected] Hydro-Mechanical Sales, Ltd. P.O. Box 1445 (Mailing), 297 Collishaw St., Suite 7 (shipping) Moncton, New Brunswick E1C 9R [email protected] J.D.S. Sales Ltd. 4 Lancaster Street, St. John s, Newfoundland A1A 5P [email protected] Les Ent. Roland Lajoie 6221 Marivaux, St-Leonard, QC H1P 3H [email protected] Les Ent. Roland Lajoie 23 du Buisson, Pont Rouge, QC G3H 1X [email protected] Mar-Win Agencies, Ltd Clifton St., Winnipeg, Manitoba R3E 2V [email protected] Northern Mechanical Sales P.O. Box 280 (mailing) 163 Pine St. (shipping), Garson, Ontario P3L 1S [email protected] Palser Enterprises, Ltd. P.O. Box (mailing), 1885 Blue Heron Dr., #4, London, Ontario N6H 5L [email protected] RAM Mechanical Marketing Inc. 905 Winnipeg Street, Regina, Saskatchewan S4R 1J [email protected] RAM Mechanical Marketing Inc. 510 Ave M South, Saskatoon, Saskatchewan S7M 2K [email protected] Walmar Mechanical Sales 24 Gurdwara Rd., Nepean, Ontario K2E 8B [email protected] 1116 Telephone EXPORT Hdqtrs.: Watts Regulator Co. 815 Chestnut St., North Andover, MA U.S.A [email protected] A Watts Water Technologies Company F-ProdSelectionGuide 1038 USA: No. Andover, MA Tel. (978) Fax: (978) Canada: Burlington, ON Tel. (905) Fax: (905) Watts