Pralinator. Instruction Manual Model #2181. Cincinnati, OH USA. Part No Revised June 1996

Transcription

1 Instruction Manual Model #2181 Part No Revised June 1996 Cincinnati, OH USA

2 SAFETY PRECAUTIONS This equipment is designed and sold for commercial use only. This equipment is not to be used by the consumer in home use. Do not allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment. Carefully read all installation instructions before operating the equipment. Always wear safety glasses when servicing this equipment. Any alterations to this equipment will void the warranty and may cause a dangerous situation. NEVER make alterations to the equipment. Machine must be properly grounded to prevent electrical shock to personnel. Do NOT immerse the equipment in water. Always unplug the equipment before cleaning or servicing. NOTE The information, specifications and illustrations contained in this manual represent the latest data available at time of publication. Right is reserved to make changes as required at the discretion of Gold Medal Products Company without notice.

3 INSTALLATION CHECKING SHIPMENT Unpack shipping carton and check thoroughly for any damage which may have occurred during transit. Claims should be filed immediately with the transportation company. Machine must be properly grounded to prevent electrical shock. ELECTRICAL REQUIREMENTS Your PRALINATER is 120V single phase, 2736 watts, 60 cycle and will draw 16 amps. A 20 amp grounded circuit is required. Your electrician must furnish sufficient current for your machine. We recommend that this machine be fused on a line by itself. Wall receptacle must be wired as shown on accompanying instruction sheet (Part No ). Failure to wire properly will void the warranty and can result in damage to the motor, heat elements, relay, lights, etc. This machine is designed to cook food product and will get hot, do not touch or work in cooking area (Kettle & Bowl) while power is on or while machine is hot. While power is on do not insert anything into cooking/mixing bowl. 1

4 OPERATING INSTRUCTIONS Before turning on machine make sure paddle spins freely and bowl is clean and free of obstructions. If the paddle does not spin freely, remove paddle wing nut, add 8 ounces water, cover kettle with the lid, and turn on heat to steam clean the kettle. To avoid serious burns, Do not touch kettle while it is hot. FROSTED NUT MIX PREPARATION 1. In a clean 1 gallon container combine 1 part imitation vanilla to 3 parts water. 2. Save 12 ounces for the batch. Fill spray bottle with the rest of the solution from the gallon container. COOKING PROCEDURE 1. Turn on the Pralinator heat switch and add 2 ½ pounds of nuts. (Use raw almonds, raw pecans, or roasted peanuts. 2. Add contents of flavor packet and 12 ounces of the vanilla solution (see above). 3. Allow machine to cook and mix until the buzzer sounds. 4. At the Buzzer, spray the frosted nuts with the vanilla solution (see above) until the buzzer stops. 5. Turn the kettle off and dump the frosted nuts onto a cooling tray, separate and allow to cool 10 minutes before serving or packaging. CARE AND CLEANING Unplug the machine before cleaning. Do not immerse in water. Clean your machine daily. A clean well kept machine is one of the best ways of advertising your product. Use a mild soap and damp cloth to clean the exterior of the unit. TO CLEAN KETTLE The easiest way to clean the kettle is to pour 6 ounces of water into the kettle when it is still hot, then place the lid on the kettle. Let it steam for ten minutes or so then remove the lid and dump the water. The mixing drum is easily removed by releasing the draw latch and removing the retainer and then the mixing drum. The mixing drum can then be taken to the sink and cleaned. The cabinet of your machine should be cleaned daily or several times a day. Kettle and all utensils should be cleaned with a sanitizing solution to help prevent contamination from microorganisms. 2

5 MAINTENANCE INSTRUCTIONS THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN- TENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE OPERATOR. Adequate eye protection must be used when servicing this equipment to prevent the possibility of injury. Do NOT immerse the equipment in water. Unplug your machine before servicing. ORDERING SPARE PARTS 1. Identify the desired part by checking it against the photos, illustrations, and/or the parts list. 2. When ordering, please include part number, part name, and quantity desired. 3. Please include your model name and machine serial number (located on the machine nameplate) with your order. 4. Address all parts orders to: Parts Department Gold Medal Products Co Medallion Drive Cincinnati, Ohio or, place orders at: (513) Fax: (513)

6 PRALINATOR ASSEMBLY 4

7 PRALINATOR ASSEMBLY (continued) 5

8 PARTS LIST PRALINATOR ASSEMBLY Item No. Part No. Description Quantity ¼-20 Bolt Pilot Light - Red Lead-In Cord Assembly Flex Cord Plug Receptacle Relay Measuring Cup Terminal Block Hole Plug Tilt Lever Coupling Tilt Lever Tilt Lever Key Set Collar Centering Bushing Grip - Handle Bar Buzzer Storage Bucket Cam Actuated Programmer Threaded Pin Control Panel Assembly Potentiometer Bracket Solid State Heat Control Motor Shipping Carton Potentiometer Cable Tie Pedestal Assembly Knob - T Handle Spring Pin ¾" Bushing " Bushing Shipping Bracket Riv Nut Label, Shipping Bracket Shipping Pallet Motor Spacer Warranty Registration Card Label, Safe Operating Instructions Terminal Block - Hi Heat Spring - Counter Weight Spur Gear Lid O-ring Bushing Seal Set Collar Mt Shelf Lock Stud Degree Connector 3 6

9 PARTS LIST PRALINATOR ASSEMBLY (continued) Item No. Part No. Description Quantity Kettle Bushing - Motor Shaft Motor Mounting Plate Bronze Bushing Junction Box Assembly Spur Gear Heat Shield Lock Nut Element Retainer #10 Washer #10 Set Screw #10 Nut ¼" Set Screw ¼" Washer ¼" Nut Mix Drum Tubular Heat Element Large Heat Element Heat Element - Small Hub Seal Body Hub Seal Hub O-ring Retaining Ring Assembly Drum Seal Junction Box Cover Eye Bolt Mixing Paddle Agitator Shaft Rtd Heat Sensor Flex Conduit - 40" Flex Conduit - 12" Conduit Bushing Thermostat Rating Plate Switch Plate Parts Manual Instruction Sheet - 4-wire Plug Switch, DPST Label - Warning, Disconnect Power Label - Unplug To Clean M.E.A. Data Plate ¼" Screw Strain Relief Motor Mounting Casting Flanged Lock Nut Bushing, Mix Bowl Hub Circuit Protector 1 7

10 ELECTRICAL SCHEMATIC 8

11 WARRANTY WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIP- TION ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said GOLD MEDAL equipment or any part thereof. The term Original Purchaser as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS COMPANY, or their authorized distributor for the equipment. THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIP- MENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERN- ING THE REPAIR OR REPLACEMENT OF PARTS. NOTE: This equipment is manufactured and sold for commercial use only. GOLD MEDAL PRODUCTS COMPANY Medallion Drive Cincinnati, Ohio USA