SIMATIC S Power supplies. The S7-300 version 5/235

Transcription

1 Application The proven power supply in the design; with PS-CPU connecting comb and for mounting on S7 rail. Technical specifications 1-phase, 24 V DC/2 A 24 V/2 A 1-phase AC Supply voltage 1 at AC nominal value 120 V 2 at AC nominal value 230 V at DC te Automatic range selection voltage 1 at AC V 2 at AC V Overvoltage resistance 2.3 V in rated, 1.3 ms Mains buffering at I out rated, min s Mains buffering at V in = 93/187 V Rated line frequency 1 0 Hz 2 60 Hz Rated line range Hz current 0.9 A 120 V nominal value 0. A 230 V nominal value 24 V nominal value 110 V nominal value Switch-on current limiting (+2 C), 22 A max. Duration of current limiting at 2 C 3ms maximum I²t, max. 1A² s Built-in incoming fuse T 1.6 A/20 V (not accessible) Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: 3 A, characteristic C 24 V/2 A Controlled, isolated DC voltage Rated voltage V out DC 24 V Total tolerance, static ± 3% Static mains compensation, 0.1 % Static load balancing, 0.2 % Residual ripple peak-peak, max. 0 mv Residual ripple peak-peak, typ. mv Spikes peak-peak, max. 10 mv Spikes peak-peak, typ. 20 mv Product feature output voltage adjustable voltage setting - Status display Green LED for 24 V OK On/off behavior overshoot of V out (soft start) Startup delay, max. 2s Voltage rise, typ. 10 ms Rated current value I out rated 2A Current range 0 2A te delivered active power typ. 48 W short-term overload current at shortcircuit 9A during run-up typical Duration of overloading ability for 90 ms during the start-up short-term overload current at shortcircuit 9A during operation typical Duration of overloading ability for 90 ms during the operational phase Parallel switching for enhanced performance Numbers of parallel switchable units for enhanced performance /23

2 Siemens AG 2013 Technical specifications 1-phase, 24 V DC/2 A (continued) 24 V/2 A Efficiency Efficiency at V out rated, I out rated, Power loss at V out rated, I out rated, Closed-loop control Dynamic mains compensation (V in rated ±1 %), max. Dynamic load smoothing (I out : 0/100/0 %), U out ± typ. 0 to 100%, typ. 100 to 0%, typ. Setting time maximum Protection and monitoring overvoltage protection Current limitation Characteristic feature of the output short-circuit protected Short-circuit protection Enduring short circuit current Effective level maximum 84 % 9W 0.1 % 0.8 % 0. ms 0. ms 1ms Additional control loop, shutdown at < 28.8 V, automatic restart A Electronic shutdown, automatic restart 2A Overload/short-circuit indicator - Safety Primary/secondary isolation Potential separation Safety extra-low output voltage U out acc. to EN and EN 0178 Protection class Class I stray current maximum 3. ma typical 0. ma CE mark UL/CSA approval UL/cUL (CSA) approval culus-listed (UL 08, CSA C ), File E143289, UL 1604 Class I Div. 2 Group A, B, C, D, File E3304 Explosion protection ATEX (EX) II 3G Ex na II T4; UL 1604 Class I, Div. 2, Group ABCD Class I, Div. 2, Group ABCD, T4 CB approval Marine approval In S7-300 system Degree of protection (EN 6029) IP20 24 V/2 A EMC Emitted interference EN 022 Class B Supply harmonics limitation not applicable ise immunity EN Operating data Ambient temperature in operation 0 60 C -te with natural convection on transport C in storage C Humidity class according to EN Climate class 3K3, no condensation Mechanics Connection technology screw-type terminals Connections Supply input L, N, PE: 1 screw terminal each for mm² single-core/finely stranded L+, M: 2 screw terminals each for mm² Auxiliary - Width of the housing 40 mm Height of the housing 12 mm Depth of the housing 120 mm Installation width 40 mm Installation height 20 mm Weight, 0.4 kg Product feature of the housing housing for side-by-side mounting Type of mounting wall mounting Type of fixing cap rail mounting Type of mounting S7-300 rail mounting Installation Can be mounted onto S7 rail Mechanical accessories Mounting adapter for standard mounting rail (6EP1971-1BA00) /236

3 Technical specifications 1-phase, 24 V DC/ A 24 V/ A 1-phase AC Supply voltage 1 at AC nominal value 120 V 2 at AC nominal value 230 V at DC te Automatic range selection voltage 1 at AC V 2 at AC V Overvoltage resistance 2.3 V in rated, 1.3 ms Mains buffering at I out rated, min. 20 ms Mains buffering at V in = 93/187 V Rated line frequency 1 0 Hz 2 60 Hz Rated line range Hz current 2.3 A 120 V nominal value 1.2 A 230 V nominal value 24 V nominal value 110 V nominal value Switch-on current limiting (+2 C), 20 A max. Duration of current limiting at 2 C 3ms maximum I²t, max. 1.2 A² s Built-in incoming fuse T 3,1 A/20 V (not accessible) Protection in the mains power input (IEC 898) Rated voltage V out DC 24 V Total tolerance, static ± 3% Static mains compensation, 0.1 % Static load balancing, 0. % Residual ripple peak-peak, max. 0 mv Residual ripple peak-peak, typ. 10 mv Spikes peak-peak, max. 10 mv Spikes peak-peak, typ. 20 mv Product feature output voltage adjustable voltage setting - Recommended miniature circuit breaker: from 6 A, characteristic C Controlled, isolated DC voltage 24 V/ A Status display Green LED for 24 V OK On/off behavior overshoot of V out (soft start) Startup delay, max. 2s Voltage rise, typ. 10 ms Rated current value I out rated A Current range 0 A te delivered active power typ. 120 W short-term overload current at 20 A short-circuit during run-up typical Duration of overloading ability for 100 ms during the start-up short-term overload current at 20 A short-circuit during operation typical Duration of overloading ability for 100 ms during the operational phase Parallel switching for enhanced performance Numbers of parallel switchable units for enhanced performance Efficiency Efficiency at V out rated, I out rated, 87 % Power loss at V out rated, I out rated, 18 W Closed-loop control Dynamic mains compensation 0.1 % (V in rated ±1 %), max. Dynamic load smoothing 1% (I out : 0/100/0 %), U out ± typ. 0.3 ms 0 to 100%, typ. 0.3 ms 100 to 0%, typ. Setting time maximum Protection and monitoring overvoltage protection Additional control loop, shutdown at < 28.8 V, automatic restart Current limitation. 6. A Characteristic feature of the output short-circuit protected Short-circuit protection Electronic shutdown, automatic restart Enduring short circuit current Effective 7A level maximum Overload/short-circuit indicator /237

4 Siemens AG 2013 Technical specifications 1-phase, 24 V DC/ A (continued) 24 V/ A Safety Primary/secondary isolation Potential separation Protection class stray current maximum typical CE mark UL/CSA approval Safety extra-low output voltage U out acc. to EN and EN 0178 Class I 3. ma 0. ma UL/cUL (CSA) approval culus-listed (UL 08, CSA C ), File E143289, UL 1604 Class I Div. 2 Group A, B, C, D, File E3304 Explosion protection ATEX (EX) II 3G Ex na II T4; UL 1604 Class I, Div. 2, Group ABCD Class I, Div. 2, Group ABCD, T4 CB approval Marine approval In S7-300 system Degree of protection (EN 6029) IP20 EMC Emitted interference EN 022 Class B Supply harmonics limitation EN ise immunity EN Operating data Ambient temperature in operation 0 60 C -te with natural convection on transport C in storage C Humidity class according to EN Climate class 3K3, no condensation 24 V/ A Mechanics Connection technology screw-type terminals Connections Supply input L, N, PE: 1 screw terminal each for mm² single-core/finely stranded L+, M: 3 screw terminals each for mm² Auxiliary - Width of the housing 60 mm Height of the housing 12 mm Depth of the housing 120 mm Installation width 60 mm Installation height 20 mm Weight, 0.6 kg Product feature of the housing housing for side-by-side mounting Type of mounting wall mounting Type of fixing cap rail mounting Type of mounting S7-300 rail mounting Installation Can be mounted onto S7 rail Mechanical accessories Mounting adapter for standard mounting rail (6EP1971-1BA00) /238

5 Technical specifications 1-phase, 24 V DC/10 A 24 V/10 A 1-phase AC Supply voltage 1 at AC nominal value 120 V 2 at AC nominal value 230 V te Automatic range selection voltage 1 at AC V 2 at AC V Overvoltage resistance 2.3 V in rated, 1.3 ms Mains buffering at I out rated, min. 20 ms Mains buffering at V in = 93/187 V Rated line frequency 1 0 Hz 2 60 Hz Rated line range Hz current 4.2 A 120 V nominal value 1.9 A 230 V nominal value 24 V nominal value 110 V nominal value Switch-on current limiting (+2 C), A max. Duration of current limiting at 2 C 3ms maximum I²t, max. 3.3 A² s Built-in incoming fuse T 6.3 A/20 V (not accessible) Protection in the mains power input (IEC 898) Rated voltage V out DC 24 V Total tolerance, static ± 3% Static mains compensation, 0.1 % Static load balancing, 0. % Residual ripple peak-peak, max. 0 mv Residual ripple peak-peak, typ. 1 mv Spikes peak-peak, max. 10 mv Spikes peak-peak, typ. 60 mv Product feature output voltage adjustable voltage setting - Recommended miniature circuit breaker: from 10 A, characteristic C Controlled, isolated DC voltage 24 V/10 A Status display Green LED for 24 V OK On/off behavior overshoot of V out (soft start) Startup delay, max. 2s Voltage rise, typ. 10 ms Rated current value I out rated 10 A Current range 0 10A te delivered active power typ. 240 W short-term overload current at 38 A short-circuit during run-up typical Duration of overloading ability for 80 ms during the start-up short-term overload current at 38 A short-circuit during operation typical Duration of overloading ability for 80 ms during the operational phase Parallel switching for enhanced performance Numbers of parallel switchable units for enhanced performance Efficiency Efficiency at V out rated, I out rated, 90 % Power loss at V out rated, I out rated, 27 W Closed-loop control Dynamic mains compensation 0.1 % (V in rated ±1 %), max. Dynamic load smoothing 2% (I out : 0/100/0 %), U out ± typ. 0 to 100%, typ. 100 to 0%, typ. Setting time maximum 0.1 ms Protection and monitoring overvoltage protection Additional control loop, shutdown at < 28.8 V, automatic restart Current limitation A Characteristic feature of the output short-circuit protected Short-circuit protection Electronic shutdown, automatic restart Enduring short circuit current 12 A Effective level maximum Overload/short-circuit indicator - /239

6 Siemens AG 2013 Technical specifications 1-phase, 24 V DC/10 A (continued) 24 V/10 A Safety Primary/secondary isolation Potential separation Protection class stray current maximum typical CE mark UL/CSA approval Safety extra-low output voltage U out acc. to EN and EN 0178 Class I 3. ma 0.6 ma UL/cUL (CSA) approval culus-listed (UL 08, CSA C ), File E143289, UL 1604 Class I Div. 2 Group A, B, C, D, File E3304 Explosion protection ATEX (EX) II 3G Ex na II T4; UL 1604 Class I, Div. 2, Group ABCD Class I, Div. 2, Group ABCD, T4 CB approval Marine approval In S7-300 system Degree of protection (EN 6029) IP20 EMC Emitted interference EN 022 Class B Supply harmonics limitation EN ise immunity EN V/10 A Operating data Ambient temperature in operation 0 60 C -te with natural convection on transport C in storage C Humidity class according to EN Climate class 3K3, no condensation Mechanics Connection technology screw-type terminals Connections Supply input L, N, PE: 1 screw terminal each for mm² single-core/finely stranded L+, M: 4 screw terminals each for mm² Auxiliary - Width of the housing 80 mm Height of the housing 12 mm Depth of the housing 120 mm Installation width 80 mm Installation height 20 mm Weight, 0.8 kg Product feature of the housing housing for side-by-side mounting Type of mounting wall mounting Type of fixing cap rail mounting Type of mounting S7-300 rail mounting Installation Can be mounted onto S7 rail Mechanical accessories Mounting adapter for standard mounting rail (6EP1971-1BA00) /240

7 Technical specifications 1-phase, 24 V DC/ A (outdoor) Supply voltage 1 at AC nominal value 2 at AC nominal value at DC te 6ES EA80-0AA0 24 V/ A 1-phase AC 120 V 230 V Set by means of selector switch on the device voltage 1 at AC V 2 at AC V Overvoltage resistance 2.3 V in rated, 1.3 ms Mains buffering at I out rated, min. 20 ms Mains buffering at V in = 93/187 V Rated line frequency 1 0 Hz 2 60 Hz Rated line range Hz current 2.1 A 120 V nominal value 1.2 A 230 V nominal value 24 V nominal value 110 V nominal value Switch-on current limiting (+2 C), 4 A max. Duration of current limiting at 2 C 3ms maximum I²t, max. 1.8 A² s Built-in incoming fuse T 3,1 A/20 V (not accessible) Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: from 10 A, characteristic C, or from 6 A, characteristic D Controlled, isolated DC voltage Rated voltage V out DC 24 V Total tolerance, static ± 3% Static mains compensation, 0.2 % Static load balancing, 0.4 % Residual ripple peak-peak, max. 10 mv Residual ripple peak-peak, typ. 40 mv Spikes peak-peak, max. 240 mv Spikes peak-peak, typ. 90 mv 6ES EA80-0AA0 24 V/ A Product feature output voltage adjustable voltage setting - Status display Green LED for 24 V OK On/off behavior overshoot of V out (soft start) Startup delay, max. 3s Voltage rise, typ. 100 ms Rated current value I out rated A Current range 0 A te delivered active power typ. 120 W short-term overload current at 20 A short-circuit during run-up typical Duration of overloading ability for 180 ms during the start-up short-term overload current at short-circuit during operation typical Duration of overloading ability for during the operational phase Parallel switching for enhanced performance Numbers of parallel switchable units for enhanced performance Efficiency Efficiency at V out rated, I out rated, Power loss at V out rated, I out rated, Closed-loop control Dynamic mains compensation (V in rated ±1 %), max. Dynamic load smoothing (I out : 0/100/0 %), U out ± typ. 0 to 100%, typ. 100 to 0%, typ. Setting time maximum Protection and monitoring overvoltage protection Current limitation Characteristic feature of the output short-circuit protected Short-circuit protection Enduring short circuit current Effective level maximum Overload/short-circuit indicator 20 A 80 ms 84 % 23 W 0.3 % 3% 0.2 ms 0.2 ms ms Additional control loop, shutdown at 30 V, automatic restart. 6. A Electronic shutdown, automatic restart A /241

8 Siemens AG 2013 Technical specifications 1-phase, 24 V DC/ A (outdoor) (continued) 6ES EA80-0AA0 24 V/ A Safety Primary/secondary isolation Potential separation Protection class stray current maximum typical CE mark UL/CSA approval Safety extra low output voltage V out according to EN and EN 0178, creepage distances and clearances > mm Class I 3. ma 0.3 ma UL/cUL (CSA) approval UL-Listed (UL 08), File E143289, CSA (CSA C ) Explosion protection - CB approval Marine approval - Degree of protection (EN 6029) IP20 EMC Emitted interference EN 011 Class A Supply harmonics limitation - ise immunity EN Operating data Ambient temperature in operation C -te with natural convection on transport C in storage C Humidity class according to EN Climate class 3K, transient condensation permitted 6ES EA80-0AA0 24 V/ A Mechanics Connection technology screw-type terminals Connections Supply input L, N, PE: 1 screw terminal each for mm² single-core/finely stranded L+, M: 3 screw terminals each for mm² Auxiliary - Width of the housing 80 mm Height of the housing 12 mm Depth of the housing 120 mm Installation width 80 mm Installation height 20 mm Weight, 0.7 kg Product feature of the housing housing for side-by-side mounting Type of mounting wall mounting Type of fixing cap rail mounting Type of mounting S7-300 rail mounting Installation Can be mounted onto S7 rail Mechanical accessories Mounting adapter for standard mounting rail (6ES7390-6BA00-0AA0) /242

9 Ordering data PS 307 load current supply, 2 A incl. connecting comb 120/230 V AC; 24 V DC current 2 A (dimensions 40 x 12 x 120) PS 307 load current supply, A incl. connecting comb 120/230 V AC; 24 V DC current A (dimensions 60 x 12 x 120) PS 307 load current supply, 10 A incl. connecting comb 120/230 V AC; 24 V DC current 10 A (dimensions 80 x 12 x 120) SIPLUS S7-300 PS 307, 10 A (extended temperature range C and medial loading) SIPLUS S7-300 PS C with Conformal Coating EN 01 certified based on 6ES7307-1EA80-0AA0 stabilized power supply : 120/230 V AC : 24 V DC/ A 6AG1307-1KA02-7AA0 6AG1307-1EA80-2AA0 Accessories Mounting adapter For snapping the new PS 307 onto a 3 mm DIN rail (EN 0022) Spare part mounting adapter for snapping the PS307 onto 3 mm standard rails 6EP BA00 6ES7390-6BA00-0AA0 /243