W DATA SHEET: RESIDUAL CURRENT CIRCUIT BREAKER A, SERIES BCF0 AND BCF6
|
|
|
- Chastity Bates
- 7 years ago
- Views:
Transcription
1 W DATA SHEET: RESIDUAL CURRENT CIRCUIT BREAKER A, SERIES BCF0 AND BCF6 W SCHRACK-INFO Any mains connection If using 4-pole. switches with 3 or 2-poles, ensure connection acc. to assembly instructions The test key T is to be operated every month (supplied adhesive instruction plate) W TECHNICAL DATA Rated voltage: 230/400 V AC 4-pole, 230 V AC 2-pole, 50 Hz Certifications: IEC/EN , Type G accord. to ÖVE E 8601 Ambient operating temperature: -25 C to +40 C Max. back-up fuse: as overload protection: as short circuit protection: In = 16A 10A gg/gl 63A gg/gl In = 25-40A 25A gg/gl 63A gg/gl In = 63A 40A gg/gl 63A gg/gl In = 80A 50A gg/gl 80A gg/gl In = 100A 63A gg/gl 100A gg/gl Short-circuit proofing: 6/10 ka, with back-up fuse 63 A gl, see print Rated breaking capacity (I m ): In = 16A In = 25A In = 40A In = 63A In = 80A In = 100A I m = 160A I m = 250A I m = 400A I m = 630A I m = 800A I m = 1000A Terminals: 2/4-pole, open mouthed terminal and lift clamps both sides, 1-35 mm 2 single core, 2x16 mm 2 multi core Finger and hand touch safe : accord. to VBG 4, ÖVE-EN 6 Rated residual current: Service life: 30 ma, 100 ma, 300 ma (other upon reqest) electrical cycles, mechanical cycles Prevents nuisance tripping caused by switching electronic light: Devices (ELD) (up to max. 20 per phase, max. 60 devices per RCBO) Special snap-on mounting: for DIN rails EN Impulse current proof: >250 A (8/20 s) >3 ka (8/20 s) Typ G >5 ka (8/20 s) Typ S PAGE 1/12
2 Release time: Sensitivity: Contact position display (red/green): Non delayed min. 10 ms delay (Type G) min. 40 ms delay (Type S) selective switch-off Sensitive to cycle change for 4-pole version W TRIPPING CHARACTERISTIC PAGE 2/12
3 W POWER LOSS BCF0 AND BCF6 W INFLUENCE OF AMBIENT TEMPERATUR ON THE MAXIMUM PERMISSIBLE CONTINUOUS CURRENT (A) Version Ambient temperature 2-pole 2-pole 4-pole 2-pole 4-pole 2-pole 4-pole 2-pole 4-pole 2-pole 4-pole Note: It is important, that these values are not exceeded. 16A and 25A RCCBs cannot be used at 60 C. PAGE 3/12
4 W NOTE Operation of the test key T checks only the functioning of the residual current (RCBO) circuit breaker. This test replaces neither the ground resistance measurement (RE), nor a proper protective conductor status check, which must be carried out separately. W DIMENSIONS AND WIRING DIAGRAMS Weight: 2 pole: 0,22kg, 4 pole 0,32kg Protection type: IP40 or IP20 covered W INSTALLATION POSITION PAGE 4/12
5 W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF0, 10KA, TYPE A RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, 10MA RCCB 16A, 2-pole, 10mA, type A (Puls) BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, 30MA RCCB 25A, 2-pole, 30mA, type A (Puls) RCCB 40A, 2-pole, 30mA, type A (Puls) RCCB 63A, 2-pole, 30mA, type A (Puls) BC BC BC RCCB 25A, 4-pole, 30mA, type A (Puls) RCCB 40A, 4-pole, 30mA, type A (Puls) RCCB 40A, 4-pole, 30mA, higher back up fuse char. gg, type A (Puls) RCCB 63A, 4-pole, 30mA, type A (Puls) RCCB 63A, 4-pole, 30mA, higher back up fuse char. gg, type A (Puls) RCCB 80A, 4-pole, 30mA, type A (Puls) RCCB 100A, 4-pole, 30mA, type A (Puls) BC BC BC BC BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, 100MA RCCB 40A, 4-pole, 100mA, type A (Puls) RCCB 63A, 4-pole, 100mA, type A (Puls) RCCB 100A, 4-pole, 100mA, type A (Puls) BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, 300MA RCCB 40A, 2-pole, 300mA, type A (Puls) RCCB 63A, 2-pole, 300mA, type A (Puls) BC BC RCCB 40A, 4-pole, 300mA, type A (Puls) RCCB 63A, 4-pole, 300mA, type A (Puls) RCCB 80A, 4-pole, 300mA, type A (Puls) RCCB 100A, 4-pole, 300mA, type A (Puls) BC BC BC BC PAGE 5/12
6 W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF0, 10KA, TYPE AC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE AC, 30MA RCCB 25 A, 2-pole, 30mA, type AC RCCB 40A, 2-pole, 30mA, type AC RCCB 63A, 2-pole, 30mA, type AC RCCB 80A, 2-pole, 30mA, type AC BC BC BC BC RCCB 25 A, 4-pole, 30mA, type AC RCCB 40A, 4-pole, 30mA, type AC RCCB 40A, 4-pole, 30mA, higher back up fuse char. gg, type AC RCCB 63A, 4-pole, 30mA, type AC RCCB 63A, 4-pole, 30mA, higher back up fuse char. gg, type AC RCCB 80A, 4-pole, 30mA, type AC RCCB 100A, 4-pole, 30mA, type AC BC BC BC BC BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE AC, 100MA RCCB 25 A, 2-pole, 100mA, type AC RCCB 40A, 2-pole, 100mA, type AC BC BC RCCB 25 A, 4-pole, 100mA, type AC RCCB 40A, 4-pole, 100mA, type AC RCCB 40A, 4-pole, 100mA, higher back up fuse char. gg, type AC RCCB 63A, 4-pole, 100mA, type AC RCCB 63A, 4-pole, 100mA, higher back up fuse char. gg, type AC RCCB 80A, 4-pole, 100mA, type AC RCCB 100A, 4-pole, 100mA, type AC BC BC BC BC BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE AC, 300MA RCCB 25 A, 2-pole, 300mA, type AC RCCB 40A, 2-pole, 300mA, type AC RCCB 63A, 2-pole, 300mA, type AC BC BC BC RCCB 25 A, 4-pole, 300mA, type AC RCCB 40A, 4-pole, 300mA, type AC RCCB 63A, 4-pole, 300mA, type AC RCCB 80A, 4-pole, 300mA, type AC RCCB 100A, 4-pole, 300mA, type AC BC BC BC BC BC PAGE 6/12
7 W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF0, 10KA, TYPE AC, MIDDLE EAST VERSION RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE AC, ME, 30MA RCCB 25 A, 2-pole, 30mA, type AC, Mideast RCCB 40A, 2-pole, 30mA, type AC Mideast RCCB 63A, 2-pole, 30mA, type AC Mideast BC002203ME BC004203ME BC006203ME RCCB 25 A, 4-pole, 30mA, type AC, Mideast RCCB 40A, 4-pole, 30mA, type AC, Mideast RCCB 63A, 4-pole, 30mA, type AC Mideast BC002103ME BC004103ME BC006103ME RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE AC, ME, 100MA RCCB 40A, 2-pole, 100mA, type AC Mideast RCCB 63A, 2-pole, 100mA, type AC Mideast BC004210ME BC006210ME RCCB 40A, 4-pole, 100mA, type AC Mideast RCCB 63A, 4-pole, 100mA, type AC Mideast BC004110ME BC006110ME RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE AC, ME, 300MA RCCB 40A, 2-pole, 300mA, type AC Mideast RCCB 63A, 2-pole, 300mA, type AC Mideast RCCB 100 A, 2-pole, 300mA, type AC, Mideast BC004230ME BC006230ME BC000230ME RCCB 40A, 4-pole, 300mA, type AC Mideast RCCB 63A, 4-pole, 300mA, type AC Mideast BC004130ME BC006130ME PAGE 7/12
8 W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF0, 10KA, TYPE A, TYPE G RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, TYPE G, 30MA RCCB 40A, 2-pole, 30mA, type G, type A (Puls) BC RCCB 40A, 4-pole, 30mA, type G, type A (Puls) RCCB 40A, 4-pole, 30mA, higher back up fuse char. gg, type G, type A RCCB 63A, 4-pole, 30mA, type G, type A (Puls) RCCB 80A, 4-pole, 30mA, type G, type A (Puls) RCCB 100A, 4-pole, 30mA, type G, type A (Puls) BC BC BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, TYPE G, 300MA RCCB 100A, 4-pole, 300mA, type G, type A (Puls) BC W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF0, 10KA, TYPE AC, TYPE G RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE AC, TYPE G, 30MA RCCB 25A, 2-pole, 30mA,type G, type AC RCCB 40A, 2-pole, 30mA, type G, type AC BC BC RCCB 40A, 4-pole, 30mA, type G, type AC RCCB 40A, 4-pole, 30mA, higher back up fuse char. gg, type G, type AC RCCB 63A, 4-pole, 30mA, type G, type AC RCCB 63A, 4-pole, 30mA, higher back up fuse char. gg, type G, type AC RCCB 80A, 4-pole, 30mA, type G, type AC RCCB 100A, 4-pole, 30mA,type G, type AC BC BC BC BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA TYPE AC, TYPE G, 100MA RCCB 25A, 2-pole, 100mA,type G, type AC RCCB 40A, 2-pole, 100mA, type G, type AC BC BC RCCB 40A, 4-pole, 100mA, type G, type AC RCCB 40A, 4-pole, 100mA, higher back up fuse char. gg, type G, type AC RCCB 63A, 4-pole, 100mA, type G, type AC RCCB 63A, 4-pole, 100mA, higher back up fuse char. gg, type G, type AC BC BC BC BC PAGE 8/12
9 W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF0, 10KA, TYPE A, TYPE S RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, TYPE S, IMPUSE CURRENT PROOF 100MA RCCB 40A, 4-pole, 100mA, type S, type A (Puls) RCCB 40A, 4-pole, 100mA, higher back up fuse char. gg, type S, type A RCCB 63A, 4-pole, 100mA, type S, type A (Puls) RCCB 63A, 4-pole, 100mA, higher back up fuse char. gg, type S, type A BC BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, TYPE S, IMPUSE CURRENT PROOF 300MA RCCB 40A, 4-pole, 300mA, type S, type A (Puls) RCCB 63A, 4-pole, 300mA,type S, type A (Puls) RCCB 63A, 4-pole, 300mA, higher back up fuse char. gg, type S, type A RCCB 80A, 4-pole, 300mA, type S, type A (Puls) RCCB 100A, 4-pole, 300mA, type S, type A (Puls) BC BC BC BC BC W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF0, 10KA, TYPE A, FREQUENZY CONVERTER PROOF RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, TYPE S, IMPUSE CURRENT PROOF FU, 300MA RCCB U fest, 40A, 4-pole, 300mA, type S, type A RCCB U fest, 63A, 4-pole, 300mA, type S, type A RCCB U fest, 63A, 4-pole, 300mA, higher back up fuse char. gg, S, type A RCCB U fest, 80A, 4-pole, 300mA, type S, type A RCCB U fest, 100A, 4-pole, 300mA, type S, type A BC BC BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, TYPE G, U 30MA RCCB U fest, 40A, 4-pole,0 30mA, type G, type A RCCB U fest, 63A, 4-pole, 30mA, type G, type A BC BC RESIDUAL CURRENT CIRCUIT BREAKER 10KA, TYPE A, TYPE S, IMPUSE CURRENT PROOF FU, 100MA RCCB U fest, 40A, 4-pole, 100mA, type S, type A RCCB U fest, 63A, 4-pole, 100mA, type S, type A RCCB U fest, 63A, 4-pole, 100mA, higher back up fuse char. gg, S, type A BC BC BC PAGE 9/12
10 W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF6, 6KA, TYPE A RESIDUAL CURRENT CIRCUIT BREAKER 6KA, TYPE A, 30MA RCCB 25A, 2-pole, 30mA, type A (Puls), 6kA RCCB 40A, 2-pole, 30mA, type A (Puls), 6kA RCCB 63A, 2-pole, 30mA, type A (Puls), 6kA BC BC BC RCCB 25A, 4-pole, 30mA, type A (Puls), 6kA RCCB 40A, 4-pole, 30mA, type A (Puls), 6kA RCCB 63A, 4-pole, 30mA, type A (Puls), 6kA BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 6KA, TYPE A, 100MA RCCB 25A, 4-pole, 100mA, type A (Puls), 6kA BC RESIDUAL CURRENT CIRCUIT BREAKER 6KA, TYPE A, 300MA RCCB 25A, 2-pole, 300mA, type A (Puls), 6kA RCCB 40A, 2-pole, 300mA, type A (Puls), 6kA RCCB 63A, 2-pole, 300mA, type A (Puls), 6kA BC BC BC RCCB 25A, 4-pole, 300mA, type A (Puls), 6kA RCCB 40A, 4-pole, 300mA, type A (Puls), 6kA RCCB 63A, 4-pole, 300mA, type A (Puls), 6kA BC BC BC W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF6, 6KA, TYPE A, TYPE G RESIDUAL CURRENT CIRCUIT BREAKER 6KA, TYPE A, 30MA, TYPE G RCCB 40A, 2pol.,30mA, type G, type A(Puls), 6kA BC RCCB 40A, 4pol.,30mA, type G, type A(Puls), 6kA BC PAGE 10/12
11 W RESIDUAL CURRENT CIRCUIT BREAKER SERIES BCF6, 6KA, TYPE AC RESIDUAL CURRENT CIRCUIT BREAKER 6KA, TYPE AC, 30MA RCCB 25A, 2-pole, 30mA, type AC, 6kA RCCB 40A, 2-pole, 30mA, type AC, 6kA RCCB 63A, 2-pole, 30mA, type AC, 6kA BC BC BC RCCB 25A, 4-pole, 30mA, type AC, 6kA RCCB 40A, 4-pole, 30mA, type AC, 6kA RCCB 63A, 4-pole, 30mA, type AC, 6kA BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 6KA, TYPE AC, 100MA RCCB 25A, 2-pole, 100mA, type AC, 6kA RCCB 40A, 2-pole, 100mA, type AC, 6kA RCCB 63A, 2-pole, 100mA, type AC, 6kA BC BC BC RCCB 25A, 4-pole, 100mA, type AC, 6kA RCCB 40A, 4-pole, 100mA, type AC, 6kA RCCB 63A, 4-pole, 100mA, type AC, 6kA BC BC BC RESIDUAL CURRENT CIRCUIT BREAKER 6KA, TYPE AC, 300MA RCCB 25A, 2-pole, 300mA, type AC, 6kA RCCB 40A, 2-pole, 300mA, type AC, 6kA RCCB 63A, 2-pole, 300mA, type AC, 6kA BC BC BC RCCB 25A, 4-pole, 300mA, type AC, 6kA RCCB 40A, 4-pole, 300mA, type AC, 6kA RCCB 63A, 4-pole, 300mA, type AC, 6kA BC BC BC PAGE 11/12
12 W RESIDUAL CURRENT CIRCUIT BREAKER 500MA (SERBIA), 10KA, TYPE AC RESIDUAL CURRENT CIRCUIT BREAKER, 500MA (SERBIA), 10KA RCCB 40A, 4-pole, 500mA, type AC RCCB 63A, 4-pole, 500mA, type AC RCCB 100A, 4-pole, 500mA, type AC BC BC BC W RESIDUAL CURRENT CIRCUIT BREAKER 500MA (SERBIA), 6KA, TYPE AC RESIDUAL CURRENT CIRCUIT BREAKER, 500MA (SERBIA), 6KA RCCB 25A, 4-pole, 500mA, type AC, 6kA RCCB 40A, 4-pole, 500mA, type AC, 6kA RCCB 63A, 4-pole, 500mA, type AC, 6kA BC BC BC PAGE 12/12
MOTOR PROTECTIVE DEVICES
W MOTOR PROTECTIVE DEVICE, SERIES MP 206 BE400206 BE400306 Inherently stable without back-up fuseup to 4 A at 400 V AC, > 4 A main back-up fuse 100 A gl Thermal and magnetic release Terminal and accessory
Series 8146/5-V37 and Series 8150/5-V37
www.stahl.de > Clear assignment safe technology easy installation > Intelligent structure only one rotary actuator for frequency-controlled drives ) 20 ms leading auxiliary contact for safe motor disconnection
Electronic overload relay EF19 and EF45
Data sheet Electronic overload relay EF19 and EF45 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays. Motor
Application Switchgear for industrial and commercial applications. U e V AC 230/400. 48 (per pole)
Overcurrentswitch,6A,2p,D-Char,AC Partno. FAZ-D6/2 Articleno. 278777 CatalogNo. FAZ-D6/2 Similar to illustration Deliveryprogramme Basic function Miniature circuit breakers Pole 2 pole Tripping characteristic
5SV Residual Current Protective Devices
s Siemens AG 2013 SENTRON 5SV Residual Current Protective Devices New portfolio for reliable personnel, material and fire protection Safe protection against residual currents Residual current protective
Electronic overload relay EF65, EF96 and EF146
Data sheet Electronic overload relay EF65, EF96 and EF146 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays.
R.C.C.B. s two-pole LEXIC
87045 LIMOGES Cedex Telephone : (+33) 05 55 06 87 87 Fax : (+ 33) 05 55 06 88 88 R.C.C.B. s two-pole LEXIC 089 06/09/10/11/12/15/16/17/18/ 27/28/29/30/35, CONTENTS PAGES 1. Electrical and mechanical characteristics...
Uncompromising safety and comfort The next generation of miniature circuit breakers MCB S 200/S 200 M
Uncompromising safety and comfort The next generation of miniature circuit breakers MCB S 200/S 200 M The details make the difference MCB S 200/S 200 M A range designed to ensure efficiency and protection
Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous. 1 auxiliary contact (N/C), instantaneous
Safety relay for monitoring E-STOP pushbuttons. Approvals Unit features Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous Safe separation of
Technical data. RCBO s DS 261 / DS 271 Residual current operated circuit breakers with integral overcurrent protection
Technical data RCBO s DS 261 / DS 271 Residual current operated circuit breakers with integral overcurrent protection When connecting aluminium conductors ensure that the contact surfaces of the conductors
Safety technique. Emergency stop module BO 5988 safemaster
Safety technique Emergency stop module BO 5988 safemaster 0221562 Function diagram Pushbutton on Mains or emergencystop () K1 According to EC Directive for machines 98/37/EG According to IEC/E 60204-1
VEO. V4PF480Y/277VSYTK02 Art.Nr.: 2104200. V4PF480Y/277VSYTK02P Art.Nr.: 2104210 TECHNICAL DATA
Monitoring of phase sequence and phase loss Monitoring of asymmetry Temperature monitoring (PTC) Supply voltage 208-480 V AC Supply circuit = measuring circuit 2 change-over contacts Width 45 mm Control
3RT1015-1BB41 CONTACTOR, AC-3 3 KW/400 V,
Automation Technology > Industrial Controls > Switching Devices > Contactors and Contactor Assemblies > Power Contactors for Switching Motors > Contactors SIRIUS 3RT10, 3-pole, 3... 250 kw 3RT1015-1BB41
Control Devices Catalogue. Control Devices. Preferred and Standard Products
Control Devices Catalogue Control Devices Preferred and Standard Products KOP.J Timer Electronic 22.5 mm Characteristics Mounting KOP.J 22.5 mm mono or multifunction high immunity to interference surface
Bimetallic Overload Relay Specifications
Technical Data Bimetallic Overload Relay Specifications Bulletin Number 193K, 193T1 Topic Page Product Overview 2 Standards compliance and Certifications 2 General Specifications 193K 3 Approximate Dimensions
SUBJECT: How to wire a motor starter Number: AN-MC-004 Date Issued: 2/08/2005 Revision: Original
SUBJECT: How to wire a motor starter Number: AN-MC-004 Date Issued: 2/08/2005 Revision: Original A motor starter is a combination of devices to allow an induction motor to start, run and stop according
Current valve. for AC 24 V pulse/pause control of electrical loads up to 30 kw
4 937 DESIO Current valve for AC 24 V pulse/pause control of electrical loads up to 30 kw SEA45.1 Use The current valve is used for the control of electric heating elements in heating, ventilation and
The complete range of consumer switchboards and switchgear
Power Distribution The complete range of consumer switchboards and switchgear www.nhp.com.au/mod6 The MOD6 range of consumer switchboards and switchgear is specifically designed for domestic and commercial
Type: DILM115(RAC240) Article No.: 239548 Sales text Contactor,55kW/400V,AC operated. Ordering information
Type: DILM115(RAC240) Article No.: 239548 Sales text Contactor,55kW/400V,AC operated Ordering information Connection technique Description Description Rated operational current Screw terminals 3 pole AC
How can a charging station for electric vehicles be set up simply and safely?
SB18 Building > Electromobility > Charging Station Design How can a charging station for electric vehicles be set up simply and safely? Requirement In order to supply electric vehicles with electric power,
Type: DILM50(230V50HZ,240V60HZ) Article No.: 277830
Type: DILM50(230V50HZ,240V60HZ) Article No.: 277830 Ordering information Rated operational current AC 3 400 V I e A 50 Max. rating for three phase motors, 50 60 Hz AC 3 230 V Max. rating for three phase
Your Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592. * see variants. Applications.
Safety Technique SAFEMASTER Emergency Stop Module BG 5924, IP 5924 Your Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592 BG 5924 IP 5924 Product Description
Technicaldata General
Currenttransformer-operatedoverloadrelay,60-90A,1N/O+1N/C Partno. ZW7-90 Articleno. 002618 CatalogNo. XTOT090C3S Deliveryprogramme Product range ZW7 current transformer-operated overload relays Description
mecotron Safety relay ESTOP-2 For emergency stop monitoring
E0006 000824 Safety relay E-2 For emergency stop monitoring Description The safety module E-2 for emergency stop monitoring is used for safety breaking one or more circuits and is designed to be incorporated
Type: DILM9 10(24VDC) Article No.: 276705
Type: DILM9 10(24VDC) Article No.: 276705 Ordering information Rated operational current AC 3 400 V I e A 9 Max. rating for three phase motors, 50 60 Hz AC 3 230 V Max. rating for three phase motors, 50
Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
Contact expansion modules
Gertebild ][Bildunterschrift Kontakterweiterungen Contact for increasing the number of available contacts Approvals Zulassungen Unit features Gertemerkmale Positive-guided relay outputs: 4 safety contacts
Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
Residual Current Protective Devices
Residual Current Protective Devices /2 Introduction / 5SM3 RCCBs /9 SIQUENCE, 5SM3 and 5SU1 universal -sensitive RCCBs, type B and type B+ /12 Additional components /1 5SM2 RC units /18 5SU1 RCBOs /25
Type: DILM32 10(24V50HZ) Article No.: 277247
Type: DILM32 10(24V50HZ) Article No.: 277247 Ordering information Rated operational current AC 3 400 V I e A 32 Max. rating for three phase motors, 50 60 Hz AC 3 230 V Max. rating for three phase motors,
Type: EASY719 DC RC Article No.: 274119. Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC. Description
Type: EASY719 DC RC Article.: 274119 Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display
Emergency stop As an emergency switching off/emergency stop device. Standards According to IEC/EN 60204-1, VDE 0113 Part 1
MainswitchSurfacemounting Partno. P3-63/I4/SVB Articleno. 207343 CatalogNo. SP3-063-I4CRQ IP65 Deliveryprogramme Product range Switch-disconnectors Basic function Main switches Maintenance switches Manual
RM17TE 183...528 V AC. Main. Product or component type. Product specific application. Relay monitored parameters 250 V DC 5 A DC
Characteristics multifunction control relay RM17-TE - range 183..528 V AC Complementary Reset time Maximum switching voltage Minimum switching current Maximum switching current [Us] rated supply voltage
Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection)
Data sheet Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) The temperature monitoring relays CM-TCS monitor overtemperature,
Contact expander modules
Gertebild ][Bildunterschrift Kontakterweiterungen Contact expansion module for increasing the number of available contacts Approvals Zulassungen Unit features Gertemerkmale Positive-guided relay outputs:
Three-phase monitoring relay CM-PFE
Data sheet Three-phase monitoring relay CM-PFE The CM-PFE is a three-phase monitoring relay that monitors the phase parameter phase sequence and phase failure in three-phase mains. 2CDC 251 005 S0012 Characteristics
Mini Motor Contactor J7KNA Main contactor Accessories Approved Standards Standard Guide No (US,C) Ordering Information tage Model Number Legend gear
Mini Motor Contactor J7KNA ) Main contactor AC & DC operated Integrated auxiliary contacts Screw fixing and snap fitting (35 mm DIN-rail) Range from 4 to 5.5 (AC 3, 380/415V) 4 -main pole version (4 AC
Actuator-Sensor-Interface
Selection and ordering data Design Order No. Price Pack 3RX9 307-0AA00 3RX9 307-1AA00 4FD5 213-0AA10-1A 3RX9 305-1AA00 3RX9 306-1AA00 Single output IP 65 current 2.4 A Rated input voltage DC 24 V current
PNOZsigma - Base units
PNOZsigma - Base units Register Login Sensors Control and Communication Electronic monitoring relays Safety Relays PNOZ X PNOZsigma PNOZelog PNOZmulti PNOZpower Configurable control systems Programmable
RM35UA13MW. range 15..600 V. Main. Product or component type. Relay monitored parameters
Characteristics multifunction voltage control relay RM35-U - range 15..600 V Complementary Reset time Maximum switching voltage [Us] rated supply voltage Supply voltage limits Power consumption in W Main
Electronic timer CT-VBS.17+18 OFF-delayed without auxiliary voltage, for DC contactors Data sheet
Characteristics Single-function OFF-delay timer for DC contactors, without auxiliary voltage Width.5 mm CDC 5 6 F3 Approvals A culus E CCC CT-VBS a Circuit diagram b Marker label Marks a CE b C-Tick Order
Manual motor starter MS116
Data sheet Manual motor starter MS116 Manual motor starters are electromechanical devices for motor and circuit protection. These devices offer local motor disconnect means, manual ON/ OFF control, and
MONITORING RELAYS. w VOLTAGE MONITORING RELAY UR5U1011. w SCHRACK-INFO. w TECHNICAL DATA
w VOLTAGE MONITORING RELAY UR5U1011 w SCHRACK-INFO AC/DC voltage monitoring in 1-phase mains Undervoltage monitoring 1 change over contact Width 17.5 mm Installation design w TECHNICAL DATA 502 1. Functions
E-STOP relays, safety gate monitors
Unit features Safety features Gertebild ][Bildunterschrift_NOT_Sch.tuer_Licht Safety relay for monitoring E-STOP pushbuttons, safety gates and light beam devices Approvals Gertemerkmale Positive-guided
Analogue Input, 4-fold, MDRC AE/S 4.1, GH Q605 0054 R0001
Analogue Input, -fold, MDRC, GH Q605 005 R0001 The analogue input is a DIN rail mounted device for insertion in the distribution board. It is connected to the EIB via the bus connecting terminal supplied.
H/L = Power supply. FN = Nominal Frequency. RN = Rated value of output burden. UN = Nominal input voltage. IN = Nominal input current.
Application : The transducer RISH CON - CA/CV (Fig.1) converts a sinusoidal AC Current or AC Voltage into a load independent DC Current or a load independent DC Voltage proportional to the measured value.
ABB 1 NEW. Three-phase monitoring relay for grid feeding CM-UFS.1. Data sheet. Features. Approvals. Marks. Order data. Order data - Accessories
2CDC 251 014 F0t09 Features Monitoring of three-phase mains for grid feeding Type-tested in accordance with DIN V VDE V 0126-1-1: February 2006 Neutral conductor connection configurable Can also be used
ABB 1. Three-phase monitoring relay CM-PFS. Data sheet. Features. Approvals. Marks. Order data. Order data - Accessories. Application.
1SR 430 824 F9300 Features Monitoring of three-phase mains for phase sequence and failure Powered by the measuring circuit 2 c/o (SPDT) contacts 1 LED for status indication Approvals R: yellow LED - relay
3753 en - 04.2004/b VE/B - VE/RG Va V riable speed drives
3753 en 04.2004/b Variable speed drives LEROYSOMER's drives provide SPEED VARIATION for a DC motor, SIMPLY and ECONOMICALLY from a singlephase power supply. CMStype technology is used. These products conform
E-STOP relays, safety gate monitors
Unit features Safety features Gertebild ][Bildunterschrift Safety relay for monitoring E-STOP pushbuttons and safety gates. Approvals Gertemerkmale Positive-guided relay outputs: 3 safety contacts (N/O),
Power Supplies 3. SDN-P DIN Rail Series
SDN-P DIN Rail Series The SDN DIN Rail power supplies provide industry leading performance. Sag Immunity, transient suppression and noise tolerant, the SDN series ensures compatibility in demanding applications.
BETA Switching. Switching Devices. 5TT5 8 Insta contactors, AC technology. Overview
BETA Switching Siemens AG 200 5TT5 Insta contactors, AC technology Overview The 5TT5 Insta contactors are equipped with an AC magnetic system and are ideal for use under harsh conditions. The auxiliary
Plug and Socket Devices CES 63 A Series 8579
www.stahl.de > Switch socket / plug 63 A > Large switch handle with clear switch position indication padlockable in 0- and I-position > Low insertion and withdrawal forces through individually encapsulated
Three-phase monitoring relays CM-PSS CM-PSS.31 and CM-PSS.41
Data sheet Three-phase monitoring relays CM-PSS CM-PSS.31 and CM-PSS.41 The three-phase monitoring relays CM-PSS.x1 monitor the phase parameters phase sequence, phase failure as well as over- and undervoltage.
Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages The CM-ESS.M is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
E-STOP relays, safety gate monitors
Unit features Safety features gang engertebild ][Bildunterschrift_NOT_Sch.tuer_Licht Safety relay for monitoring E-STOP pushbuttons, safety gates and light beam devices Approvals Gertemerkmale Positive-guided
Thermal-Magnetic Circuit Breaker 3120-...-M1-..
Thermal-Magnetic Circuit Breaker -...-M-.. Description Single or two pole rocker switch/thermal-magnetic circuit breaker with trip-free mechanism (S-type TM CBE to EN 34). The addition of a magnetic tripping
Micro Contactors. Micro Contactor Relays. Micro Contactors With Solder Pins. Coil voltages. Micro Reversing Contactor. Technical Data.
Micro Contactors Micro Contactor Relays 0 Micro Contactors Micro Contactors With Solder Pins Coil voltages Micro Reversing Contactor 3 Technical Data 4 Dimensions 8 9 Micro Contactor Relays 4pole C Operated
LC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 - <= 440 V 65 A - 220 V AC coil
Product data sheet Characteristics LC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 -
PHOENIX CONTACT - 2012-12-14. Features
Electronic monitoring relay for phase sequence, phase failure, and asymmetry monitoring Data sheet 101748_en_03 1 Description PHOEIX COTACT - 2012-12-14 Features Increasingly higher demands are being placed
Cable Plug acc. to DIN EN 175301-803, Form A
Cable Plug acc. to DIN EN 175301-803, Form A Complete program Contact form 18 mm Also available with LED indicator Optional 4-pin version for pressure switch or impulse valves respectively Versions with
ELECTROMAGNETIC DISC BRAKES
ELECTROMAGNETIC DISC BRAKES TYPE 66E 15/30 52.121 Hand release Lining wear adjustment Torque adjustment 4 holes ø13 DISC SIZE Ø A Braking torque Nm Regulated from (40-100%) Reaction on the shaft N Control
Mini Circuit Breakers, Fuse Blocks, and Electronic Circuit Protection
Technical Data Mini Circuit Breakers, Fuse Blocks, and Electronic Circuit Protection Topic Page 1489-M Miniature Circuit Breakers 2 1492-SP Supplementary Protectors 15 1492-D Circuit Breakers 27 188 Regional
Switch Actuator, 8-fold, 10 A, MDRC AT/S 8.10.1, GH Q631 0075 R0111
, GH Q631 0075 R0111 The 8-fold switch actuator is a DIN rail mounted device for insertion in the distribution board. It is connected to the EIB via a bus terminal. In the event of bus voltage failure,
Thermistor motor protection relays CM-MSS.22 and CM-MSS.23
Data sheet Thermistor motor protection relays CM-MSS.22 and CM-MSS.23 The thermistor motor protection relays CM-MSS.22 and CM-MSS.23 monitor the winding temperature of motors and protect them from overheating,
SMS 4 / SMS 5 safety mat Product information
SMS 4 / SMS 5 safety mat Product information SMS 4 / SMS 5 safety mats Safety mats are used for the protection of man on machinery and plants with hazardous movements. Typical fields of application are,
System pro M compact Miniature Circuit Breaker S 200/S 200 M
Data Sheet System pro M compact Miniature Circuit Breaker S 200/S 200 M 2CDC021023S0012 2CDC021038S0012 The miniature circuit breakers of the System pro M compact series S 200 and S 200 M provide state-of-the-art
Pluggable interface relays CR-P Pcb relays
2CDC 293 034 F0004 1 2 4 3 Features 9 different supply s: DC versions: 12 V, 24 V, 48 V, 110 V AC versions: 24 V, 48 V, 110 V, 120 V, 230 V Output contacts: 1 c/o (16 A) or 2 c/o (8 A) Cadmium-free contact
E-STOP relays, safety gate monitors
Gertebild ][Bildunterschrift Safety relay for monitoring E-STOP pushbuttons and safety gates. Unit features Gertemerkmale Positive-guided relay outputs: 2 safety contacts (N/O), instantaneous Connection
STEP-PS/1AC/12DC/1.5. Extract from the online catalog. Order No.: 2868567. DIN rail power supply unit 12 V DC/1.5 A, primary switched-mode, 1- phase
Extract from the online catalog STEP-PS/1AC/12DC/1.5 Order No.: 2868567 DIN rail power supply unit 12 V DC/1.5 A, primary switched-mode, 1- phase Commercial data EAN 4046356292924 Pack 1 pcs. Customs tariff
E-STOP relays, safety gate monitors
Gertebild ][Bildunterschrift Safety relay for monitoring E-STOP pushbuttons and safety gates. Approvals Unit features Gertemerkmale Positive-guided relay outputs: 2 safety contacts (N/O), instantaneous
E-STOP relays, safety gate monitors
Unit features Unit description Gertebild ][Bildunterschrift Safety relay for monitoring E-STOP pushbuttons and safety gates. Approvals Gertemerkmale Positive-guided relay outputs: 3 safety contacts (N/O),
Product and Applications Description. Application Programs. Example of Operation. GAMMA instabus Technical Product-Information.
Product and Applications Description The power supply units N 125/x2 can supply DC 24 V power from an additional pair of terminals (yellowwhite). This DC 24 V output voltage can be used to power e.g. an
49 Series - Relay interface modules 8-10 - 16 A. Features
Features 1 & 2 Pole relay interface modules 5 µm Gold plate contacts for low level switching capability 49.31-50x0-1 Pole 10 A (screw terminal) 49.52-50x0-2 Pole 8 A (screw terminal) 49.72-50x0-2 Pole
RY2 miniature industrial relays
6 RY2 Relays of general application For plug-in sockets, 35 mm rail mount acc. to PN-EN 60715 or on panel mounting Flat insert connectors - faston x 0,5 mm Recognitions, certifications, directives: RoHS,
MINI MCR-SL-R-UI(-SP)
Resistance/potiposition transducer INTERFACE Data Sheet 0807_en_05 Description PHOENIX CONTACT - 0/008 Features The slim MINI MCR-SL-R-UI... potiposition transducer has a width of only 6. mm and converts
Fuses for Semiconductor Protection - Cylindrical Fuses. Class: Voltage ratings: Current ratings: Standards: Approvals: Features and Benefits
Fuses for Semiconductor Protection - Cylindrical Fuses SIBA cylindrical Ultra-Rapid fuses are available in six different sizes They can be ordered with an integral striker for blown fuse indication or
AF09-30-22-.. / AF09Z-30-22-.. 2-stack 3-pole Contactors AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101403D0201 24/03/11 AF09-30-22-.. / AF09Z-30-22-.. 2-stack 3-pole Contactors AC / DC Operated - with Screw Terminals AF09(Z) contactors are used for controlling power circuits
NF71E-.. / NFZ71E-.. Contactor Relays AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101433D0201 28/03/11 NF71E-.. / NFZ71E-.. Contactor Relays AC / DC Operated - with Screw Terminals NF(Z) contactor relays are used for switching auxiliary and control circuits.
J TB/TW Temperature limiter, temperature monitor
JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net
HSP GmbH Zum Handwerkerhof 2 90530 Wendelstein Tel. 09129 / 2852-0 Fax: 09129 / 2852-11 Web: www.hsshsp.de EMAIL: HSP@hsshsp.de NTG-3000.
NTG-3000 Transducer Data Sheet Document Version 2.8 Page 1 of 10 Versions / Revisions: Document Creation Author Description version date 2.0 2012-07-25 P. Compensis First official version 2.1 2012-08-24
Multifunctional three-phase monitoring relays CM-MPS CM-MPS.43
Data sheet Multifunctional three-phase monitoring relays CM-MPS CM-MPS.43 The three-phase monitoring relay CM-MPS.43 monitors the phase parameters phase sequence, phase failure, over- and undervoltage
HERZ-Thermal Actuators
HERZ-Thermal Actuators Data Sheet 7708-7990, Issue 1011 Dimensions in mm 1 7710 00 1 7710 01 1 7711 18 1 7710 80 1 7710 81 1 7711 80 1 7711 81 1 7990 00 1 7980 00 1 7708 11 1 7708 10 1 7708 23 1 7709 01
is then retained absolutely without interruption.
Page 1 of 11 DC UPS uninterruptible power supplies - DC UPS module 15 A Compact design, only 50 mm wide Absolutely interruption-free buffering of power failures through immediate electronic connection
MICROSENS. Central 48 V DC Power Supplies for PoE-Components. Description. Features
Central 48 V DC Power Supplies for PoE-Components MICROSENS Description Active network equipment which is supporting the Power-over-Ethernet functions, typically requires a powerful 48 V DC power supply.
48 SERIES Relay interface modules 10 A
48 Relay interface modules 10 A 1 CO relay interface modules, mm wide Ideal interface for PLC and electronic systems Type 48.P3 1 CO 10 A s Type 48.31 1 CO 10 A s AC coils or DC sensitive coils Supply
Process modules Digital input PMI for 24 V DC inputs for 120 V AC inputs
E031026 000823 Process modules Digital input PMI for inputs for 120 V AC inputs PMI Input E4, E5, GND L- PMI 120 V AC Input E4, E5, Common C E6, E7, GND L- E6, E7, Common C LEDs for the inputs operation
33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application
33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application Features Compliant with the IEEE802.3at Standard -40 to +60 C Temperature Range Diagnostic LEDs Full Protection
Electronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact The CT-AHD.12 is an electronic time relay with OFF-delay. It is from the CT-D range. With their MDRC profile and a width of only
RM4TG20 three-phase network control relay RM4-T - range 200..500 V
Characteristics three-phase network control relay RM4-T - range 200..500 V Complementary [Us] rated supply voltage Output contacts Setting accuracy of time delay Delay at power up Measuring cycle Marking
48.12. 2 pole, 8 A Safety relay. Screw terminal. 35 mm rail (EN 60715) mounting. 2 CO (DPDT) 8/15 250/400 2,000 500 0.37 8/0.65/0.
48 Series - Relay interface modules 8 A Features 48.12 2 Pole Safety relay interface modules, 15.8 mm wide 48.12-2 Pole 8 A (screw terminal) DC sensitive coils Relay with forcibly guided contacts according
Magnetic and Hydraulic-Magnetic Circuit Breaker 8340-G2...
Magnetic and Hydraulic-Magnetic Circuit Breaker 840-G2... Description Single, two and three pole magnetic circuit breakers with trip-free mechanism and push/pull on/off manual actuation. A choice of fast
Components for System Solutions E9/5. Ex d Enclosure System Made of Light Metal or Stainless Steel, "Flameproof Enclosure" Series 8264. www.stahl.
> Installation chamber can be fully used > Up to three mounting levels can be used > Saving of weight > Compact > Easy to combine > 26 enclosure versions > 15 window versions www.stahl.de 10303E00 The
0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N
55 Series - General purpose relays 7-10 A Features 55.12 55.13 55.14 Printed circuit mount, general purpose 2, 3 & 4 Pole relays 55.12-2 Pole 10 A 55.13-3 Pole 10 A 55.14-4 Pole 7 A AC coils & DC coils
IEC style contactors - long electrical and mechanical life Complete range from mini-contactors to 630 Amp i n d u c t i ve AC3 ra t i n g s Wide
- long al and mechanical life Complete range from mini-contactors to 630 Amp i n d u c t i ve AC3 ra t i n g s Wide range coils +0% to -30% Finger safe terminals Four-pole versions available NO + NC and
Safety automation solutions
Operating principle, characteristics Preventa safety s types XPS AV,, For and switch monitoring Operating principle Safety s XPS AV, and are used for monitoring circuits conforming to standards EN/ISO
Quick Connect. quick - simple - efficient. www.g-mw.de
Quick Connect quick - simple - efficient www.g-mw.de Phone: +49 9103 7129-0 Fax: +49 9103 7129-207 Innovative connection technology to plug three single-phase current transformers to multifunctional power
Circuit Breakers. NRC Series. NRC Series. 900 www.idec.com
Switches & Pilot Lights Display Lights NRC series circuit breakers offer circuit protection which is far superior to using fuses in applications containing relay circuits, motor circuits, heater circuits,
Solid State Relays Industrial, 1-Phase ZS w. LED Types RS 23, RS 40, RS 48
Solid State Relays Industrial, 1-Phase ZS w. LED Types RS 23, RS 0, RS 8 Zero switching AC Solid State Relay Direct copper bonding (DCB) technology in 25A and 0A types LED indication Clip-on IP 20 protection
Manual Motor Starter MS 116 up to 16 A Technical Data
Manual Motor Starter MS 116 up to 16 A Technical Data Type MS 116 Standards: Major International IEC 60 947-4-1 / IEC 60 947-2 and European Standards EN 60 947-4-1 / EN 60 947-2 Approvals, Certificates