DINSTAR DAG1000-4S4O with Elastix Setup Guide
|
|
- Clement Daniel Boyd
- 8 years ago
- Views:
Transcription
1 DINSTAR DAG1000-4S4O with Elastix Setup Guide Shenzhen Dinstar Technologies Co., Ltd. Address: Floor 6, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China Telephone: Fax: s: Website:
2 A. Elastix Setup Procedure To setup the Elastix server for the Dinstar DAG1000-4S4O A1. Login the webpage of Elastix server, the server s address is determined by customer, in this paper, we set the Elastix server s address to be A2. Please enter the username and password and then press Enter or Submit button to go to the Dashboard of Elastix server, also the username and password are determined by customer when install Elastix server. A3. After login, please go to PBX page to start configuration.
3 A4. Go to PBX-->Trunks page, click Add SIP Trunk to add one. A5. When add the SIP trunk, fill in the following information Trunk Name: out-o1, for example Outgoing settings: Trunk Name: out-o1, for example host:
4 Incoming Settings: username: define the username use to authentication when configure the DAG1000 s FXO port, 1001, for example; secret: define the secret Please click Submit to save the changes. A6. Configure the outbound route on PBX-->Outbound Route page, fill in the following information: Route Name: define a name for this route, outdag4o1, for example;
5 Set dial rule for this rule: This rule defines that, all the dialed numbers should start with 8 and the length of the dialed numbers should be equal or longer than three. In Caller ID field, fill in one extension number, to define that this route can only be used by the corresponding extension. In the upon picture, the route can only be used by extension Then please click Submit to save the changes. Notice: If user want to make the route can be used by any extension, just leave Caller ID option blank. A7. Like A5 and A6, Set another trunk and outbound route. 1) Set trunk out-o2 and configure the corresponding outgoing and incoming settings.
6
7 2) Set outbound route outdag4o2, and set the dial patter.
8 In the upon picture, the route can only be used by extension 6001, also dial sequence which starts with 9 and is no less than 3 three characters will match this route. A8. Configure inbound route on PBX-->Inbound Route page Description: todag4o1, for example DID number: enter a DID number, s, for example; Configure destination for this inbound route: customer can set the destination to be an extension or IVR or others, if make it IVR, customer need configure IVR first. In this example, we set the destination to be extension 6000.
9 Click Submit to save the changes. A8. After finish configuration, please click the notice Apply Configuration Changes Here to make the configurations effective. B. DAG1000-4S4O setup procedure B1. Login the webpage of DAG1000, the IP address is determined by the customer, default IP of the device is , and in this paper, we use as device s address. Please fill in the username and password, both are admin by default. The main page of DAG1000-4S4O VoIP gateway: IP Address: in this example Firmware Version: DAG1000-4S4O Rev PCB 23.1 LOGIC 0 BIOS 1, Built on
10 Sep , 15:33:46. Notice: If user need the latest firmware for the device, please send to To upgrade a new firmware, please go to Maintenance-->Firmware Upload page, click to select the firmware file and click to start uploading, after finish, please restart the device to make the new firmware take effect. B2. Configure SIP server address on SIP server page.
11 SIP Server Address: in this example; SIP Server Port: 5060 in this example; SIP Register Interval: 1800 in this example; Click to save the configurations. B3. Configure authentication information on Port page. SIP User ID (1001 in this example as configuration of Trunks, please refer to A5) To VoIP Hotline (DID Number s in this example as configuration of Inbound Routes, please refer to A8)
12 B4. Configure outbound route on Call&Routing-->IP->Tel Routing page. Description: out1 in this example B5 Configure inbound route on the Call & Routing->Tel-IP Routing page Description: e1 in this example; Call from: Port 4 in this example;
13 B6. Configure port5 as port4, and set up the corresponding outbound and inbound route.
14 B7. Enable CID on the Advanced-> FXS/FXO page
15 Enable One stage dialing C. Test C1. Register 6000 and register 6001 to Elastix; Here we use eyebeam to register 6000 as the example. C2. Use 6000 to call , call sets up successfully; use 6000 to call , call fails since route does not match. C3. Use 6001 to call , call fails, since outbound route does not match; use 6001 to call , call sets up successfully. C4. Use a mobile phone to call the port4 s number, according to the inbound route, call goes to 6000; C5. Use a mobile phone to call the port5 s number, according to the inbound route, call goes to Notice: If user wants to make different incoming calls goes to different extensions(or IVR), please setup different DID numbers on Elastix s Inbound route, and separate different DID numbers on different port s Offhook Auto-Dial option.
16 Example: Set two different Inbound routes on Elastx s PBX-->Inbound Route page as following: Then all the incoming call from port4 will go to extension 6000 and all incoming calls from port5 will go to extension 6001.
How to Config MTG1000B With T1 and Elastix
How to Config MTG1000B With T1 and Elastix Dinstar Technologies Co., Ltd. Address: Floor 6, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China 518052 Telephone: +86-755-26456664 Fax: +86-755-26456659
More informationDinstar GSM VoIP Gateway Interoperability Guide. DWG and 3CX System
Dinstar GSM VoIP Gateway Interoperability Guide DWG and 3CX System Shenzhen Dinstar Technologies Co., Ltd. Address: Floor 6, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China 518052 Telephone:
More informationHow to set fax using Dinstar s gateway and 3CX
How to set fax using Dinstar s gateway and 3CX Dinstar Technologies Co., Ltd. Address: Floor 6 Guoxing Building Changxing Road Nanshan District Shenzhen China 518057 Telephone: 86-755-26456664 Fax: 86-755-26456659
More informationConfiguring Positron s V114 as a VoIP gateway for a 3cx system
Assumptions: Configuring Positron s V114 as a VoIP gateway for a 3cx system The IP address of the V114 is 192.168.1.2 The IP address of the 3CX PBX System is 192.168.1.110 3CX already has some IP phones
More informationHow to Configure MTG200 with FreePBX
How to Configure MTG200 with FreePBX A. FreePBX Setup Procedure To setup the FreePBX sever for Dinstar MTG200 A1. Login the FreePBX Open the web of the FreePBX server with its IP address, the IP is assigned
More informationAllo PRI Gateway and Elastix Server
Allo PRI Gateway and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single Allo PRI Gateway configuration. We re going to configure a SIP Trunk
More informationHow to use IP-0x to connect to Skype
How to use IP-0x to connect to Skype Product Guide Version: 1.0 2010-10-14 Content CONTACT ATCOM... 2 HOW TO USE IP-0X TO CONNECT TO SKYPE... 2 YOU NEED TO SIGN UP A SKYPE MANAGER ACCOUNT.... 2 REGISTER
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1
ALLWORX SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1 Goal The purpose of this configuration guide is to describe the steps needed to configure the Allworx 6x
More informationQuick Installation Guide
Quick Installation Guide PRI Gateway Version 2.4 Table of Contents Hardware Setup... 1 Accessing the WEB GUI... 2 Notification LEDs (On the Front Panel of the Gateway)... 3 Creating SIP Trunks... 4 Creating
More informationHow to Connect MyPBX to NeoGate TG via SIP Trunking
How to Connect MyPBX to NeoGate TG via SIP Trunking Version: 1.0 Yeastar Technology Co., Ltd. Date: 2013.11.16 http://www.yeastar.com 1/11 Contents: 1. Introduction... 3 2. Connect MyPBX to NeoGate TG...
More informationSIP Trunking with Elastix. Configuration Guide for Matrix SETU VTEP
SIP Trunking with Elastix Configuration Guide for Matrix SETU VTEP Contents Setup Diagram 3 SIP Trunk Configuration in Elastix for SETU VTEP 4 Outgoing Call configuration in Elastix 7 Incoming call configuration
More informationHow to Connect MyPBX to Skype
Version: 2.0 Yeastar Technology Co., Ltd. Date: 2014.11.20 Table of Contents About This Guide... 3 1. Register Skype SIP Trunk on MyPBX... 4 2. Configure MyPBX with Inbound Calling... 7 2.1 Receive Incoming
More informationConfiguration guide for Switchvox and Cbeyond.
Configuration guide for Switchvox and Cbeyond. This document will guide a Switchvox administrator through configuring the system to utilize Cbeyond s BeyondVoice with SIPconnect service. After you have
More informationKhomp KGSM-USB SPX and Elastix Server
Khomp KGSM-USB SPX and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single Khomp KGSM-USB SPX Interface Card configuration. Figure 1-1. Setup
More informationA Guide to Connecting to FreePBX
A Guide to Connecting to FreePBX FreePBX is a basic web Graphical User Interface that manages Asterisk PBX. It includes many features available in other PBX systems such as voice mail, conference calling,
More informationVoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
VoiceGear/3CX Integration Guide Ver.0.1 Page 2 1. OVERVIEW... 3 1.1 SETTING UP 3CX PBX...4 1.2 SETTING UP VOICEGEAR GATEWAY...5 2. VOICEGEAR-3CX SIP INTEGRATION... 6 2.1 3CX CONFIGURATION...7 2.2 VOICEGEAR
More informationElastix Server VoIP Intercom Setup Guide
The IP Endpoint Company Elastix Server VoIP Intercom Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1
More informationConfiguring 3CX for Spitfire SIP Trunks
Configuring 3CX for Spitfire SIP Trunks This document is a guideline for configuring Spitfire SIP trunks onto a 3CX which includes the settings required for Inbound DDI routing and Outbound CLI presentation.
More informationQuick Installation Guide
Quick Installation Guide MegaPBX Version 2.1 Quick Installation Guide v2.1 www.allo.com 2 Table of Contents Initial Setup of MegaPBX... 4 Notification LEDs (On the Front Panel of the Gateway)... 5 Create
More information3CX Guide sip.orbtalk.co.uk
3CX Guide sip.orbtalk.co.uk Table of Contents 1. Outbound Dialling 2. Inbound Routing 3. Outbound CLI 4. Additional Network Configuration 1. Outbound dialling: The Customer will have been provided with
More informationConfiguring Elastix 2.0.0 57 for Spitfire SIP Trunks
Configuring Elastix 2.0.0 57 for Spitfire SIP Trunks This document is a guideline for configuring Spitfire SIP trunks onto Elastix 2.0.0 and includes the settings required for Inbound DDI routing and Outbound
More informationnexvortex Setup Guide
nexvortex Setup Guide CUDATEL COMMUNICATION SERVER September 2012 510 S P R I N G S T R E E T H E R N D O N V A 2 0 1 7 0 + 1 8 5 5. 6 3 9. 8 8 8 8 Introduction This document is intended only for nexvortex
More informationPBX Setup Basic setup procedures
Basic setup procedures 1) Configure the SpoTel PBX & Voip phones to a router/switch 2) Setup Extensions on SpoTel PBX -> Testing: Call between Extension phones 3) Setup Trunks on Spotel PBX 4) Setup Outbound
More informationDigium Switchvox AA65 PBX Configuration
Digium Switchvox SIP Trunking using Optimum Business SIP Trunk Adaptor and the Digium Switchvox AA65 IP-PBX v23695 Goal The purpose of this configuration guide is to describe the steps needed to configure
More informationSIP Trunk Configuration Guide. using
SIP Trunk Configuration Guide using www.cbeyond.net 1-877-441-9783 The information contained in this document is specific to setting up SIP connections between Vertical SBX IP 320 and Cbeyond. If you require
More informationPeer-to-Peer SIP Mode with FXS and FXO Gateways
Peer-to-Peer SIP Mode with FXS and FXO Gateways New Rock s SIP based VoIP gateways with FXS and FXO ports support peer-to-peer mode which has many applications in deploying enterprise multi-site telephone
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and ShoreTel IP PBX Phone System
SHORETEL SIP Trunking using Optimum Business SIP Trunk Adaptor and ShoreTel IP PBX Phone System Goal The purpose of this configuration guide is to describe the steps needed to configure the ShoreTel IP
More informationRelease Notes for NeoGate TE100 16.18.0.X
Release Notes for NeoGate TE100 16.18.0.X ===Firmware Version: V16.18.0.2==== Applicable Model: NeoGate TE100 Release Date: October 25th, 2014 http://www.yeastar.com 1/6 1. New Features 1. Added support
More informationGrandstream Networks, Inc. UCM6510 Basic Configuration Guide
Grandstream Networks, Inc. UCM6510 Basic Configuration Guide Index Table of Contents OVERVIEW... 4 SETUP ENVIRONMENT... 5 QUICK INSTALLATION... 6 CONNECT UCM6510... 6 ACCESS UCM6510 WEB INTERFACE... 6
More informationVoIP Intercom and Elastix Server
VoIP Intercom and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single VoIP Intercom configuration. In this configuration, the VoIP Intercom acts
More informationConfiguring the PBX Call Routing Table for outbound calls (with security against unsecured calls)
Configuring the PBX Call Routing Table for outbound calls (with security against unsecured calls) The Quadro s Call Routing Table (CRT) defines how incoming and outgoing calls will be handled by the Quadro.
More information3rd Party VoIP Phone Setup Guide (Panasonic UT113-123)
3rd Party VoIP Phone Setup Guide (Panasonic UT113-123) We are changing how we add 3rd party VoIP phones to accounts. Going forward, you can simply add a 3rd Party Softphone and use those credentials to
More information3rd Party VoIP Phone Setup Guide (Panasonic 500-550b)
3rd Party VoIP Phone Setup Guide (Panasonic 500-550b) We are changing how we add 3rd party VoIP phones to accounts. Going forward, you can simply add a 3rd Party Softphone and use those credentials to
More informationConfiguring Quadro IP PBXs with "SIP Connect"
Configuring Quadro IP PBXs with "SIP Connect" Revision: 1.0 Abstract: This document describes how to configure the Quadro IP PBXs to use the IP-PSTN service from SIP Connect PAGE 1 Document Revision History
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More information3CX PBX v12.5. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5 Table of Contents 1. Overview 3 2. Prerequisites 3 3. PBX Configuration 3 4. Creating Extensions 4 5. VoIP Provider Setup
More informationGrandstream Networks, Inc.
Grandstream Networks, Inc. UCM6100 Basic Configuration Guide Grandstream Networks, Inc. www.grandstream.com TABLE OF CONTENTS OVERIEW... 4 SETUP GUIDE SCENARIO... 4 QUICK INSTALLATION... 5 Connecting the
More informationSIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX
June 26th, 2014 SIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX Page 1 of 30 Table of Contents 1 Overview... 3 2 Prerequisites... 3 3 Network Topology... 4 4 Description
More informationHow to extend Skype to MyPBX
How to extend Skype to MyPBX 1. Activate Skype for SIP on Skype... 2 1.1 Register for Skype Manager... 2 1.2 Create a SIP Profile and buy a Channel Subscription... 2 1.3 Allocate Skype Credit to the SIP
More informationIPPBX FAQ. For Firmware Version: V2.0/V3.0 2013-12-11
For Firmware Version: V2.0/V3.0 2013-12-11 Contents 1. IPPBX Access... 3 1.1 How to access IPPBX via SSH?... 3 1.2 How to access IPPBX if I forget the IP of WAN?... 4 1.3 How to retrieve WEB password via
More informationConnecting with Vonage
Connecting with Vonage Vonage (http://www.vonage.com/) offers telephone service using the VoIP (Voice over Internet Protocol) standard SIP (Session Initiation Protocol). The service allow users making
More informationIntegrating Asterisk FreePBX with Lync Server 2010
1 Integrating Asterisk FreePBX with Lync Server 2010 Author: Baaskar R 1 www.baaskarcharles.com 2 Integrating Asterisk FreePBX with Lync Server 2010... 1 AsteriskNow package Source... 3 Installing AsteriskNow...
More informationAtcom MP01 and Elastix Server
Atcom MP01 and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram This is a setup diagram for a mesh network of Atcom MP01 configuration. When everything is configured we ll be able to
More informationRelease Notes for NeoGate TA410/TA810 41.18.0.X
Release Notes for NeoGate TA410/TA810 41.18.0.X ===Firmware Version: V41.18.0.11==== Applicable Model: NeoGate TA410/TA810 Release Date: January 15th, 2015 http://www.yeastar.com1/6 1. New Features 1.
More informationQuick Installation Guide
Quick Installation Guide PSTN / VoIP PBX Version 2.1 Table of Contents Hardware Setup... 1 Notification LEDs (On the Front Panel of the Gateway)... 2 PSTN/VOIP PBX Quick Installation Wizard... 3 Accessing
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Panasonic KX-NCP500 IP PBX V2.0502
PANASONIC SIP Trunking using Optimum Business SIP Trunk Adaptor and the Panasonic KX-NCP500 IP PBX V2.0502 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More informationApplication Note Configuring the Synapse SB67070 SIP Gateway for Broadvox GO! SIP Trunking
Configuring the Synapse SB67070 SIP Gateway for Broadvox GO! SIP Trunking 2012 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed
More informationVoIP Ceiling Speaker with Allworx 6x Server Setup Guide
VoIP Ceiling Speaker with Allworx 6x Server Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1-1 is a setup
More informationTHINKTEL COMMUNICATIONS 3CX PHONE SYSTEM V.11. 3CX Phone System THINKTEL SIP TRUNK from scratch
THINKTEL COMMUNICATIONS 3CX PHONE SYSTEM V.11 3CX Phone System THINKTEL SIP TRUNK from scratch TA B L E O F C O N T E N T S 1.1 INTRODUCTION... 3 2.1 REQUIREMENTS... 4 2.2 3CX PHONE SYSTEME INSTALLATION...
More informationUsing FreePBX with Twilio Elastic SIP Trunking
Using FreePBX with Twilio Elastic SIP Trunking FreePBX works great with Twilio! We support it, it is what many of us use. There are a few tricks, especially for Origination, that are documented here, that
More informationDigium IP-PBX. SIP Trunking using the Optimum Business SIP Trunk Adaptor and the Digium IP-PBX
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the Digium IP-PBX Table of Contents 1. Overview 3 2. Prerequisites 3 3. Digium PBX Configuration 3 3.1 SIP Trunking 4 3.2 Extensions/DID 7
More informationIP PBX. SD Card Slot. FXO Ports. PBX WAN port. FXO Ports LED, RED means online
1 IP PBX SD Card Slot FXO Ports PBX LAN port PBX WAN port FXO Ports LED, RED means online 2 Connect the IP PBX to Your LAN Internet PSTN Router Ethernet Switch FXO Ports 3 Access the PBX s WEB GUI The
More informationSIP Trunking using the Optimum Business SIP Trunk Adaptor and the FortiVoice IP-PBX
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the FortiVoice IP-PBX 1 Table of Contents 1. Overview 3 2. Prerequisites 3 3. FortiVoice Configuration 3 3.1 Global Settings 4 3.2 SIP Registration
More informationGrandstream Networks, Inc.
Grandstream Networks, Inc. Interoperability Tutorial: Configuring UCM6100 Series with FreePBX Grandstream Networks, Inc. www.grandstream.com FreePBX is a Registered Trademark of Schmooze Com, Inc. Index
More informationHow to Build a Simple Virtual Office PBX System Using TekSIP and TekIVR
How to Build a Simple Virtual Office PBX System Using TekSIP and TekIVR This document explains how to build a simple virtual office PBX system using TekSIP and TekIVR. In this example following components
More informationSIP Trunk Configuration for nexvortex
SIP Trunk Configuration for nexvortex Document version: 1.0 Modification date: June 25, 2013 Prerequisites The nexvortex customer service provides the following communication parameters: Parameter Example
More informationIntegrating VoIP Phones and IP PBX s with VidyoGateway
Integrating VoIP Phones and IP PBX s with VidyoGateway Updated February 2011 INDEX: I. ABSTRACT.1 II. III. IV. VIDYOGATEWAY OVERVIEW.. 1 NETWORK TOPOLOGIES AND DEFINITIONS...2 CONNECTING TO VIDYOCONFERENCES
More informationZyXEL IP PBX Support Note. ZyXEL IP PBX (X2002) VoIP. Support Notes
ZyXEL IP PBX (X2002) VoIP Support Notes Version 1.00 October 2008 1 Contents Overview ZyXEL IP PBX Support Note 1. How to manage and maintain your IPPBX?...3 1.1 Firmware Upgrade..3 1.2 Backing up your
More informationConfiguring the Synapse SB67070 SIP Gateway from AT&T for Clearfly SIP Trunking. January 2013
Configuring the Synapse SB67070 SIP Gateway from AT&T for Clearfly SIP Trunking January 2013 1 Introduction This guide was created to assist Synapse partners with configuring the Synapse SB67070 SIP Gateway
More informationSIP Trunk Configuration for Broadvox
Document version: 1.0 Modification date: December 09, 2009 Prerequisites The Broadvox customer service provides the following communication parameters: Parameter Example Explanation BTN & Username: 4801234560
More informationTech Bulletin 2012-002. IPitomy AccessLine SIP Provider Configuration
support@ipitomy.com 941.306.2200 Tech Bulletin 2012-002 Description This guide is intended to streamline the installation of AccessLine SIP trunks in the IPitomy IP PBX. In our combined testing we determined
More informationMediatrix 3000 with Asterisk June 22, 2011
Mediatrix 3000 with Asterisk June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 Network Topology... 3 Equipment Detail... 3 Configuration of the Fax Extension... 4 Configuration
More informationHow to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions
How to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Toshiba Strata CIX IP PBX to connect to Integra
More informationTHINKTEL COMMUNICATIONS CUDATEL PHONE SYSTEM 270. High Availability and SIP-TRUNK Configuration
THINKTEL COMMUNICATIONS CUDATEL PHONE SYSTEM 270 High Availability and TABL E OF CO NTENTS 1.1 CONFIGURING TELEPHONE SERVICE PROVIDER (THINKTEL)... 3 1.2 OUTBOUND CALL ROUTING... 5 1.3 INBOUND CALL FROM
More informationnexvortex Setup Template
nexvortex Setup Template ZULTYS, INC. April 2013 5 1 0 S P R I N G S T R E E T H E R N D O N V A 2 0 1 7 0 + 1 8 5 5. 6 3 9. 8 8 8 8 Introduction This document is intended only for nexvortex customers
More informationStep into the next level of office communication
Step into the next level of office communication Agenda ConVox Hosted IP-PBX Hosted IP-PBX v/s PBX comparison Setup comparison Comprehensive Features Admin Features Screen shot Summary of benefit comparison
More informationHow to setup Mobility Extension on the 2N OfficeRoute and 2N VoiceBlue Enterprise
How to setup Mobility Extension on the 2N OfficeRoute and 2N VoiceBlue Enterprise This is the manual for a firmware version 2.2.9 Our scenario: 1. Firstly you need to set up the IP address of the OfficeRoute
More informationConnecting with Free IP Call
Connecting with Free IP Call Free IP Call (http://www.freeipcall.com/) offers telephone service using the VoIP standard SIP. The service allow users making/receiving VoIP calls to/from VoIP telephone numbers
More informationKnowledgebase Solution
Knowledgebase Solution Updated: 2/27/2014 Configuring an EdgeMarc for SIP trunking with an IP PBX This document describes the steps needed to configure an IP PBX behind the EdgeMarc which is pointing to
More informationQuick Start Guide CREATING A NEW SITE
IVY is our complete control panel for managing you or your customers SIP trunks and hosted PBX settings. This guide will help you get up and running with IVY as quickly as possible. First thing we need
More informationOBiTALK Portal Device Management
OBiTALK Portal Device Management By using the OBiTALK portal, you can easily manage features, control device access privileges and add up to two (2) BYOD (Bring Your Own Device) SIP or Google Voice service
More informationConfiguring a Mediatrix 500 / 600 Enterprise SIP Trunk SBC June 28, 2011
Configuring a Mediatrix 500 / 600 Enterprise SIP Trunk SBC June 28, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 Solution Overview... 3 Network Topology... 4 Network Configuration...
More informationHow To Set Up Virtual Fax On Zcoo (U20/50/60/100) On A Pc Or Macbook Or Ipod (U21/50) On An Ipod Or Ipo (U19/50 Or 60
ZYCOO new generation IP Phone system---coovox Series (U20/50/60/100) support virtual fax. Virtual fax is an important feature to help enterprise reduce the cost and promote the efficient communication.
More informationSIP Trunking Test Results for CudaTel Communication Server
SIP Trunking Test Results for CudaTel Communication Server Table of Contents 1. Executive Summary... 2 4. Software and Hardware Equipment Requirements for Testing... 3 5. Test Configurations... 4 5.1.
More informationSnom 720 and Elastix Server
Snom 720 and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single IP Phone Snom 720 configuration. The phone is setup as a SIP telephony device.
More informationSetup Guide: on the MyNetFone Service. Revision History
Setup Guide: on the MyNetFone Service Revision History Version Author Revision Description Release Date 1.0 Sampson So Initial Draft 02/01/2008 2.0 Sampson So Update 27/09/2011 1 Table of Contents Introduction...
More informationApplication Note. IP8000 Conference Phone Configuration Guide. Table of Contents. Overview. Requirements. ST-10010 October 25, 2007
Application Note ST-10010 October 25, 2007 IP8000 Conference Phone Configuration Guide This application note provides the details on adding the IP8000 conference phone to the ShoreTel IP phone system.
More informationLink2VoIP SIP Trunk Setup
DSX Link2VoIP SIP Trunk Setup April 23, 2011 Issue 1.00 NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484 Copyright 2011 NEC Corporation of America 6535 N. State Highway 161 Irving, TX 75039-2402
More informationGrandstream Networks, Inc. How to Integrate UCM6100 with Microsoft Lync Server
Grandstream Networks, Inc. How to Integrate UCM6100 with Microsoft Lync Server Index Table of Contents OVERVIEW... 3 UCM6100 CONFIGURATION... 4 STEP 1: CREATE SIP PEER TRUNK... 4 STEP 2: CONFIGURE OUTBOUND
More informationUCM61xx Configuration
UCM61xx Configuration Grandstream UCM61xx IPPBX firmware version 1.0.4.7 has passed SIP Trunk interoperability testing with Broadvox on February 12 th, 2014. This document introduces major configuration
More informationAudioCodes Mediant 1000 Configuration Guide
AudioCodes Mediant 1000 Configuration Guide 2010 FaxBack, Inc. All Rights Reserved. NET SatisFAXtion and other FaxBack products, brands and trademarks are property of FaxBack, Inc. Other products, brands
More informationOfficeServ 7100 IP-PBX. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Samsung
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Samsung OfficeServ 7100 IP-PBX 1 Table of Contents 1. Overview 3 2. Prerequisites 3 3. OfficeServ 7100 PBX Configuration 3 3.1 Network
More informationVoIP Intercom with Allworx 6x Server Setup Guide
VoIP Intercom with Allworx 6x Server Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1-1 is a setup diagram
More informationSIP Trunking using the Optimum Business SIP Trunk adaptor and the AltiGen Max1000 IP PBX version 6.7
SIP Trunking using the Optimum Business SIP Trunk adaptor and the AltiGen Max1000 IP PBX version 6.7 Goal The purpose of this configuration guide is to describe the steps needed to configure the AltiGen
More informationOptimum Business SIP Trunk Set-up Guide
Optimum Business SIP Trunk Set-up Guide For use with IP PBX only. SIPSetup 07.13 FOR USE WITH IP PBX ONLY Important: If your PBX is configured to use a PRI connection, do not use this guide. If you need
More informationHotline. Configure Hotline
This chapter provides information about the hotline feature which extends the Private Line Automatic Ringdown (PLAR) feature, which allows you to configure a phone so that when the user goes off hook (or
More informationVocia MS-1 Voice-over-IP Interface. Avaya System Verification. Configuring Avaya Aura Session Manager system with Biamp s Vocia MS-1
Configuring Avaya Aura Session Manager system with Biamp s Vocia MS-1 Vocia MS-1 Voice-over-IP Interface The Biamp Vocia Message Server (MS-1) includes functionality to allow pages to be initiated over
More informationNexeTalk Telephone Interconnect
NexeTalk Telephone Interconnect NexeTalk Telephone Interconnect User Guide August 01, 2014 1 Introduction NexeTalk Telephone Interconnect NexeTalk Telephone Interconnect is an integral part of NexeTalk
More informationDiscover the Power of 5. User s Guide. Pbx v1.0 Application
Discover the Power of 5 User s Guide Pbx v1.0 Application Document Revision 06 October 27, 2011 Media5 Corporation User s Guide Media5 Corporation 4229 Garlock Street Sherbrooke, Québec, Canada J1L 2C8
More informationCisco Unified Communications Manager SIP Trunk Configuration Guide for the VIP-821, VIP-822 and VIP-824
Valcom Network Trunk Ports, models, are compatible with Cisco Unified Communications Manager as either a Third-party SIP Device (Basic or Advanced) or as a SIP Trunk. To preserve the Caller ID information
More informationCisco CallManager 4.1 SIP Trunk Configuration Guide
Valcom Session Initiation Protocol (SIP) VIP devices are compatible with Cisco Unified Communications Manager systems. For versions of Communications Manager that do not support SIP endpoints (such as
More information3COM VCX PBX Server VoIP Intercom Setup Guide
3COM VCX PBX Server VoIP Intercom Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1 is a setup diagram
More informationConfiguring the Cisco SPA9000 Voice System with the Cyberdata VoIP Intercom for Door Bell Applications
APPLICATION NOTE Configuring the Cisco SPA9000 Voice System with the Cyberdata VoIP Intercom for Door Bell Applications Introduction The Cyberdata VoIP Intercom, is a SIP-based Control unit that allows
More informationbabytel UC540 Configuration Guide
Introduction The information in this document is intended as a general guide to help you set up the babytel service on your SIP compatible telephone system. It contains only babytel-specific parameters
More informationOpenVox GSM Gateway Function Manual
Rev: 1.0 Date: April 15, 2014 From: OpenVox support group Contact info: support@openvox.cn OpenVox GSM Gateway Function Manual OpenVox VoxStack GSM Gateway is a feature-rich, highly available and flexible
More informationConfiguration BCP Skype for Business
Configuring Skype for Business using Grandstream CPE Devices Thank you for your interest in configuring Grandstream s SIP devices for Skype s SIP Trunking Service. This document describes the basic configuration
More informationInternet Telephony PBX System
Internet Telephony PBX System GSM Gateway PSTN call busy forward to GSM Configuration Copyright PLANET Technology Corporation. All rights reserved. Case 32: PSTN call busy forward to GSM Configuration
More informationAvaya IP Office SIP Trunk Configuration Guide
Valcom Session Initiation Protocol (SIP) VIP devices are compatible with SIP-enabled versions of Avaya IP Office (5.0 and higher). The Valcom device can be added to the IP Office system as a SIP Trunk.
More informationF-SECURE MESSAGING SECURITY GATEWAY
F-SECURE MESSAGING SECURITY GATEWAY DEFAULT SETUP GUIDE This guide describes how to set up and configure the F-Secure Messaging Security Gateway appliance in a basic e-mail server environment. AN EXAMPLE
More informationRingCentral Office. Configure Aastra phones with RingCentral
TM RingCentral Office Configure Aastra phones with RingCentral Configuring Aastra phones Overview... 2 Getting ready to setup your Aastra phones... 2 Configuring the Aastra Phone... 4 Overview Aastra s
More information