Dinstar GSM VoIP Gateway Interoperability Guide. DWG and 3CX System
|
|
- Heather Peters
- 5 years ago
- Views:
Transcription
1 Dinstar GSM VoIP Gateway Interoperability Guide DWG and 3CX System Shenzhen Dinstar Technologies Co., Ltd. Address: Floor 6, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China Telephone: Fax: s: Website: 1
2 1. Background More calls than ever are being made/received using mobile phones, especially with the explosion of Smartphone's and flexible/home working. The DWG2001/4/8 SIP/GSM Gateways from Dinstar are a cost-effective SIP/GSM gateway for SOHO, SMEs and system integrators. The Dinstar GSM/VoIP gateways allow a SIP based IP PBX telephone system or VoIP line to be connected directly to the GSM cellular network, which can dramatically lower the cost of mobile calls by taking advantage of lower mobile to mobile tariffs. 2. Introduction This guide explains how to connect DWG VOIP gateway to 3CX via IP. We can configure the VOIP gateway and 3CX to achieve communication between softphone and mobile phone. In this way we can help customers save expensive telephone charges. 3. Connection 4. Configuration 4.1 3CX Configuration 1). Add Extension Click Add Extension button, as follow 2
3 Add the extension number 101 and 102 according to the diagram method. 2) Open 3CX softphone, 101 as an extension of the IP phone registered to 3CX soft-switch. As follows: 3
4 3) Click the bottom button, select the accounts button for register the IP phone to 3CX. Click New to add new extension number. 4). Add PSTN Gateway Click Add PSTN Gateway button, as follow: Then, add a DWG device as PSTN gateway as below: Click Next, filled in gateway hostname or IP Click Next, then change the authentication password for a password easy to remember. 4
5 Inbound Route Day and Inbound Route Night changed to just adding extension number 102. Click Next, in accordance with the following method fill in outbound rules. Here, destination number prefix is set to 4, the target number is Click finish to complete PSTN Gateway configuration. Click PSTN devices as follow 5
6 And then select just the configuration of the PSTN Gateway dinstar-dwg2008. Select Inbound Parameters and enter the following configuration page. SIP Field: Contact: Host Part Variable: Custom Field Custom Value: (DWG IP address) Then, click Add/Update and then click OK Click Ports/Trunks Status as follow Choose the PSTN relay set before, set Connect to Extension is 101(softphone extension number). 6
7 5). Inbound Rules Configure Inbound Rules. First, click Inbound Rules. Set in accordance with the following method. Till now, 3CX PBX is done. 7
8 4.2 Gateway Configuration Enter the gateway IP address in the browser s address bar. Enter a user name and password in the dialog box. User name and password are admin. After entering the following configuration page 8
9 1) System parameter setting Select System Configuration in left navigation tree. Enter Service Parameter configuration to set DTMF Parameter and other parameters. DTMF Parameter: this parameter should match with 3CX system, RFC2833 and SIGNAL optional; Allow Call from PSTN to IP without Registration: enable peer to peer call from PSTN to IP direction; Allow Call from IP to PSTN without Registration: enable peer to peer call from IP to PSTN direction; Keep default settings for other fields. 2) Configure SIP parameter SIP Server Address: 3CX PBX IP address SIP Server Port: 3CX PBX SIP port number Register Interval: expires time of REGISTER message, it indicates how long the DWG send re-register to 3CX PBX. Keep default settings for other fields. 9
10 3) Configure Port parameter Here, we set All ports register used same user ID to yes then all SIP ports would register with the same SIP account. SIP User ID: Virtual extention number of PSTN devices setting in 3CX PBX Authenticate ID: Authentication ID of PSTN devices setting in 3CX PBX Authenticate password: password set at PSTN devices of 3CX PBX if SIP authentication was set Keep default settings for other fields or change them as your need. 4) SIM port group configuration The device has a default port group setting, change or add port group as your need: Add port 0 to 5 to port group, 3CX extension could be able to make outgoing calls with those 6 SIM ports. 10
11 5) Routing Configuration Modify default IP->Tel Routing Source Prefix: all the caller number must match the source prefix. It specifies the source prefix allow to send call out Any: include anonymous, 0xxxx, 1[2-9]xxxx etc. Source IP: SIP server which is 3CX PBX IP. Destination Prefix:called number must match the destination prefix, any means allow to called any number Destination: destination SIM port or port group You can change destination prefix and IP->tel routing as your need Modify default Tel->IP Routing Source Prefix: all the caller number must match the source prefix. It specifies the source prefix allow to send call out Any: include anonymous, 0xxxx, 1[2-9]xxxx etc. Source: it indicate source SIM channel incoming from mobile to 3CX PBX Destination Prefix:called number must match the destination prefix, any means allow to called any number Destination: mobile call to 3CX PBX 11
12 You can change destination prefix and Tel->IP routing as your need 5). Restart equipment Click restart button of tools to reboot the device and wait 30 seconds to make configuration affect. 5. Test 1) Dial 4 on IP phone can call the number for xxxx mobile user. 2) Dial gateway 0 port SIM card number can call IP phone registered on3cx. Configuration is completed. 12
How to set fax using Dinstar s gateway and 3CX
How to set fax using Dinstar s gateway and 3CX Dinstar Technologies Co., Ltd. Address: Floor 6 Guoxing Building Changxing Road Nanshan District Shenzhen China 518057 Telephone: 86-755-26456664 Fax: 86-755-26456659
DINSTAR DAG1000-4S4O with Elastix Setup Guide
DINSTAR DAG1000-4S4O with Elastix Setup Guide Shenzhen Dinstar Technologies Co., Ltd. Address: Floor 6, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China 518057 Telephone: +86 755 2645
How to Config MTG1000B With T1 and Elastix
How to Config MTG1000B With T1 and Elastix Dinstar Technologies Co., Ltd. Address: Floor 6, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China 518052 Telephone: +86-755-26456664 Fax: +86-755-26456659
How to Connect X-lite to GSM Gateway. Version: 1.0
How to Connect X-lite to GSM Gateway Version: 1.0 Dinstar Technologies Co., Ltd. Date: 2014. 06.16 http://www.dinstar.com 1 / 9 Contents 1. Introduction... 3 Related Gateway Series... 3 Related Firmware
VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
VoiceGear/3CX Integration Guide Ver.0.1 Page 2 1. OVERVIEW... 3 1.1 SETTING UP 3CX PBX...4 1.2 SETTING UP VOICEGEAR GATEWAY...5 2. VOICEGEAR-3CX SIP INTEGRATION... 6 2.1 3CX CONFIGURATION...7 2.2 VOICEGEAR
Configuring Positron s V114 as a VoIP gateway for a 3cx system
Assumptions: Configuring Positron s V114 as a VoIP gateway for a 3cx system The IP address of the V114 is 192.168.1.2 The IP address of the 3CX PBX System is 192.168.1.110 3CX already has some IP phones
3CX PBX v12.5. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5 Table of Contents 1. Overview 3 2. Prerequisites 3 3. PBX Configuration 3 4. Creating Extensions 4 5. VoIP Provider Setup
THINKTEL COMMUNICATIONS 3CX PHONE SYSTEM V.11. 3CX Phone System THINKTEL SIP TRUNK from scratch
THINKTEL COMMUNICATIONS 3CX PHONE SYSTEM V.11 3CX Phone System THINKTEL SIP TRUNK from scratch TA B L E O F C O N T E N T S 1.1 INTRODUCTION... 3 2.1 REQUIREMENTS... 4 2.2 3CX PHONE SYSTEME INSTALLATION...
Connecting with Vonage
Connecting with Vonage Vonage (http://www.vonage.com/) offers telephone service using the VoIP (Voice over Internet Protocol) standard SIP (Session Initiation Protocol). The service allow users making
Configure your 3CX in our IP telephone service.
Configure your 3CX in our IP telephone service. This user guide will explain how to configure a 3CX Phone System turning into a small office with three extensions (1000, 1001 y 1002) and connect with Netelip
3CX Guide sip.orbtalk.co.uk
3CX Guide sip.orbtalk.co.uk Table of Contents 1. Outbound Dialling 2. Inbound Routing 3. Outbound CLI 4. Additional Network Configuration 1. Outbound dialling: The Customer will have been provided with
Allo PRI Gateway and Elastix Server
Allo PRI Gateway and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single Allo PRI Gateway configuration. We re going to configure a SIP Trunk
Digium Switchvox AA65 PBX Configuration
Digium Switchvox SIP Trunking using Optimum Business SIP Trunk Adaptor and the Digium Switchvox AA65 IP-PBX v23695 Goal The purpose of this configuration guide is to describe the steps needed to configure
How to use IP-0x to connect to Skype
How to use IP-0x to connect to Skype Product Guide Version: 1.0 2010-10-14 Content CONTACT ATCOM... 2 HOW TO USE IP-0X TO CONNECT TO SKYPE... 2 YOU NEED TO SIGN UP A SKYPE MANAGER ACCOUNT.... 2 REGISTER
Connecting with Free IP Call
Connecting with Free IP Call Free IP Call (http://www.freeipcall.com/) offers telephone service using the VoIP standard SIP. The service allow users making/receiving VoIP calls to/from VoIP telephone numbers
Connecting with sipgate
Connecting with sipgate sipgate (http://www.sipgate.co.uk/) offers telephone service using the VoIP standard SIP. sipgate covers every area code within the United Kingdom and provides a local Direct Inward
SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1
ALLWORX SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1 Goal The purpose of this configuration guide is to describe the steps needed to configure the Allworx 6x
SIP Trunking with Elastix. Configuration Guide for Matrix SETU VTEP
SIP Trunking with Elastix Configuration Guide for Matrix SETU VTEP Contents Setup Diagram 3 SIP Trunk Configuration in Elastix for SETU VTEP 4 Outgoing Call configuration in Elastix 7 Incoming call configuration
How to Configure MTG200 with FreePBX
How to Configure MTG200 with FreePBX A. FreePBX Setup Procedure To setup the FreePBX sever for Dinstar MTG200 A1. Login the FreePBX Open the web of the FreePBX server with its IP address, the IP is assigned
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the FortiVoice IP-PBX
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the FortiVoice IP-PBX 1 Table of Contents 1. Overview 3 2. Prerequisites 3 3. FortiVoice Configuration 3 3.1 Global Settings 4 3.2 SIP Registration
Avaya IP Office SIP Trunk Configuration Guide
Valcom Session Initiation Protocol (SIP) VIP devices are compatible with SIP-enabled versions of Avaya IP Office (5.0 and higher). The Valcom device can be added to the IP Office system as a SIP Trunk.
How to Connect MyPBX to NeoGate TG via SIP Trunking
How to Connect MyPBX to NeoGate TG via SIP Trunking Version: 1.0 Yeastar Technology Co., Ltd. Date: 2013.11.16 http://www.yeastar.com 1/11 Contents: 1. Introduction... 3 2. Connect MyPBX to NeoGate TG...
AudioCodes Mediant 1000 Configuration Guide
AudioCodes Mediant 1000 Configuration Guide 2010 FaxBack, Inc. All Rights Reserved. NET SatisFAXtion and other FaxBack products, brands and trademarks are property of FaxBack, Inc. Other products, brands
Configuring Quadro IP PBXs with "SIP Connect"
Configuring Quadro IP PBXs with "SIP Connect" Revision: 1.0 Abstract: This document describes how to configure the Quadro IP PBXs to use the IP-PSTN service from SIP Connect PAGE 1 Document Revision History
SIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX
June 26th, 2014 SIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX Page 1 of 30 Table of Contents 1 Overview... 3 2 Prerequisites... 3 3 Network Topology... 4 4 Description
Configuring 3CX for Spitfire SIP Trunks
Configuring 3CX for Spitfire SIP Trunks This document is a guideline for configuring Spitfire SIP trunks onto a 3CX which includes the settings required for Inbound DDI routing and Outbound CLI presentation.
3CX PHONE SYSTEM CUSTOMER CONFIGURATION ADVICE. Configuring for Integra Telecom SIP Solutions
3CX PHONE SYSTEM CUSTOMER CONFIGURATION ADVICE Configuring for Integra Telecom SIP Solutions BACKGROUND This document provides guidance for configuring the 3CX Phone System to properly interface to and
A Guide to Connecting to FreePBX
A Guide to Connecting to FreePBX FreePBX is a basic web Graphical User Interface that manages Asterisk PBX. It includes many features available in other PBX systems such as voice mail, conference calling,
Integrating Asterisk FreePBX with Lync Server 2010
1 Integrating Asterisk FreePBX with Lync Server 2010 Author: Baaskar R 1 www.baaskarcharles.com 2 Integrating Asterisk FreePBX with Lync Server 2010... 1 AsteriskNow package Source... 3 Installing AsteriskNow...
SIP Trunk Configuration Guide. using
SIP Trunk Configuration Guide using www.cbeyond.net 1-877-441-9783 The information contained in this document is specific to setting up SIP connections between Vertical SBX IP 320 and Cbeyond. If you require
GSM Gateway Function Overview
Function Overview AP-GSM1002 (2-Port) AP-GSM1004 (4-Port) AddPac Technology AP-GSM1001 (1-Port) 2010, Sales and Marketing www.addpac.com Contents GSM Outbound Call GSM Inbound Call VoIP to GSM Outbound
SIP Trunking using Optimum Business SIP Trunk Adaptor and ShoreTel IP PBX Phone System
SHORETEL SIP Trunking using Optimum Business SIP Trunk Adaptor and ShoreTel IP PBX Phone System Goal The purpose of this configuration guide is to describe the steps needed to configure the ShoreTel IP
Understand SIP trunk and registration in DWG gateway Version: 1.0 Dinstar Technologies Co., Ltd. Date: 2014. 09.29
Understand SIP trunk and registration in DWG gateway Version: 1.0 Dinstar Technologies Co., Ltd. Date: 2014. 09.29 http://www.dinstar.com 1 / 9 Contents Chapter 1: Authors and changes logs... 3 Chapter
Enabling Users for Lync services
Enabling Users for Lync services 1) Login to collaborate.widevoice Server as admin user 2) Open Lync Server control Panel as Run As Administrator 3) Click on Users option and click Enable Users option
SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
IP PBX. SD Card Slot. FXO Ports. PBX WAN port. FXO Ports LED, RED means online
1 IP PBX SD Card Slot FXO Ports PBX LAN port PBX WAN port FXO Ports LED, RED means online 2 Connect the IP PBX to Your LAN Internet PSTN Router Ethernet Switch FXO Ports 3 Access the PBX s WEB GUI The
Application Notes for Configuring QuesCom 400 IP/GSM Gateway with Avaya IP Office using H.323 trunks Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring QuesCom 400 IP/GSM Gateway with Avaya IP Office using H.323 trunks Issue 1.0 Abstract These Application Notes describe the configuration
OfficeServ 7100 IP-PBX. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Samsung
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Samsung OfficeServ 7100 IP-PBX 1 Table of Contents 1. Overview 3 2. Prerequisites 3 3. OfficeServ 7100 PBX Configuration 3 3.1 Network
Unicorn60x0 IP ANALOG GATEWAY ASTERISK CONFIGURATION
Unicorn60x0 IP ANALOG GATEWAY ASTERISK CONFIGURATION BASIC CONFIGURATION OF THE Unicorn60x0 WITH ASTERISK Due to the various deployment possibilities of the Unicorn60x0 and Asterisk, this configuration
Wave 500 IP PBX v4.5. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Wave 500 IP PBX v4.5
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the Wave 500 IP PBX v4.5 1 Table of Contents 1. Overview 3 2. Prerequisites 3 3. PBX Configuration 3 4. Creating Extensions 4 5. Inbound/Outbound
Configuring the CounterPath X-Lite SIP Softphone
NetVanta Unified Communications Technical Note Configuring the CounterPath X-Lite SIP Softphone Introduction CounterPath X-Lite is a free Session Initiation Protocol (SIP)-based softphone that is interoperable
SUTUS Business Central 5800 ThinkTel Configuration
SUTUS Business Central 5800 ThinkTel Configuration This document explains how to configure SUTUS Business Central 5800 to connect to the ThinkTel VoIP service. Configuring SUTUS Business Central 5800 to
Integrating VoIP Phones and IP PBX s with VidyoGateway
Integrating VoIP Phones and IP PBX s with VidyoGateway Updated February 2011 INDEX: I. ABSTRACT.1 II. III. IV. VIDYOGATEWAY OVERVIEW.. 1 NETWORK TOPOLOGIES AND DEFINITIONS...2 CONNECTING TO VIDYOCONFERENCES
Copyright ZYCOO All Rights Reserved 1 / 8
Copyright ZYCOO All Rights Reserved 1 / 8 If you have a scenario where you have two CooVox IP PBXs in two different locations then you can integrate them together to make free phone calls between locations.
Avaya IP Office SIP Configuration Guide
Valcom Session Initiation Protocol (SIP) VIP devices are compatible with SIP-enabled versions of Avaya IP Office (5.0 and higher). The Valcom device is added to the IP Office system as a SIP Extension.
Cisco Unified Communications Manager SIP Trunk Configuration Guide
Valcom PagePro SIP (Session Initiation Protocol) Paging Servers, models VIP-201 and VIP-204, are compatible with Cisco Unified Communications Manager as either a Third-party SIP Device (Basic or Advanced)
Application Note. IP8000 Conference Phone Configuration Guide. Table of Contents. Overview. Requirements. ST-10010 October 25, 2007
Application Note ST-10010 October 25, 2007 IP8000 Conference Phone Configuration Guide This application note provides the details on adding the IP8000 conference phone to the ShoreTel IP phone system.
Basic configuration of the GXW410x with Asterisk
Basic configuration of the GXW410x with Asterisk Please note that due to the customizable nature of both the GXW410x and Asterisk and the vast deployment possibilities, these instructions should be taken
Digium IP-PBX. SIP Trunking using the Optimum Business SIP Trunk Adaptor and the Digium IP-PBX
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the Digium IP-PBX Table of Contents 1. Overview 3 2. Prerequisites 3 3. Digium PBX Configuration 3 3.1 SIP Trunking 4 3.2 Extensions/DID 7
How to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions
How to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Toshiba Strata CIX IP PBX to connect to Integra
SIP Trunking using Optimum Business Sip Trunk Adaptor and the Zultys MX250 IP PBX
SIP Trunking using Optimum Business Sip Trunk Adaptor and the Zultys MX250 IP PBX Table of Contents Goal 3 Prerequisites 3 Zultys MX250 Configuration 4 Network Settings 4 Phone Registration and Assignment
Direct IP Calls. Quick IP Call Mode
Unicorn3112 Tips Direct IP Calls...1 Quick IP Call Mode...1 PSTN Pass Through...2 VoIP-to-PSTN Calls...2 PSTN-to-VoIP Calls...3 Route Calls to PSTN...4 Forward Calls to PSTN...4 Forward Calls to VoIP...4
THINKTEL COMMUNICATIONS CUDATEL PHONE SYSTEM 270. High Availability and SIP-TRUNK Configuration
THINKTEL COMMUNICATIONS CUDATEL PHONE SYSTEM 270 High Availability and TABL E OF CO NTENTS 1.1 CONFIGURING TELEPHONE SERVICE PROVIDER (THINKTEL)... 3 1.2 OUTBOUND CALL ROUTING... 5 1.3 INBOUND CALL FROM
SIP Trunking using the Optimum Business SIP Trunk adaptor and the AltiGen Max1000 IP PBX version 6.7
SIP Trunking using the Optimum Business SIP Trunk adaptor and the AltiGen Max1000 IP PBX version 6.7 Goal The purpose of this configuration guide is to describe the steps needed to configure the AltiGen
Quick Installation Guide
Quick Installation Guide PRI Gateway Version 2.4 Table of Contents Hardware Setup... 1 Accessing the WEB GUI... 2 Notification LEDs (On the Front Panel of the Gateway)... 3 Creating SIP Trunks... 4 Creating
This document is an application note for connecting the GS8 modular gateway with Zed-3 SE family IP PBX.
Zed-3 501 Valley Way Milpitas CA 95035 USA GS8 Modular Gateway Connecting to the SE Family IP PBX Voice: +1-408-587-9333 Fax: +1-408-586-9038 www.zed-3.com Application note, 96-90000-00, July 2008 This
Quick Installation Guide
Quick Installation Guide MegaPBX Version 2.1 Quick Installation Guide v2.1 www.allo.com 2 Table of Contents Initial Setup of MegaPBX... 4 Notification LEDs (On the Front Panel of the Gateway)... 5 Create
SIP Trunking Test Results for CudaTel Communication Server
SIP Trunking Test Results for CudaTel Communication Server Table of Contents 1. Executive Summary... 2 4. Software and Hardware Equipment Requirements for Testing... 3 5. Test Configurations... 4 5.1.
Avaya IP Office 8.1 Configuration Guide
Avaya IP Office 8.1 Configuration Guide Performed By tekvizion PVS, Inc. Contact: 214-242-5900 www.tekvizion.com Revision: 1.1 Date: 10/14/2013 Copyright 2013 by tekvizion PVS, Inc. All Rights Reserved.
Mediatrix 4404 Step by Step Configuration Guide June 22, 2011
Mediatrix 4404 Step by Step Configuration Guide June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents First Steps... 3 Identifying your MAC Address... 3 Identifying your Dynamic IP Address...
PBX Setup Basic setup procedures
Basic setup procedures 1) Configure the SpoTel PBX & Voip phones to a router/switch 2) Setup Extensions on SpoTel PBX -> Testing: Call between Extension phones 3) Setup Trunks on Spotel PBX 4) Setup Outbound
SIP Trunking using Optimum Business SIP Trunk Adaptor and the Panasonic KX-NCP500 IP PBX V2.0502
PANASONIC SIP Trunking using Optimum Business SIP Trunk Adaptor and the Panasonic KX-NCP500 IP PBX V2.0502 Goal The purpose of this configuration guide is to describe the steps needed to configure the
How to Configure the Avaya IP Office 6.1 for use with Integra Telecom SIP Solutions
How to Configure the Avaya IP Office 6.1 for use with Integra Telecom SIP Solutions Overview This document provides a reference for configuration of the Avaya IP Office to connect to Integra Telecom SIP
THINKTEL COMMUNICATIONS DIGIUM G100/G200 PRI OVER IP SIP TRUNKING
THINKTEL COMMUNICATIONS DIGIUM G100/G200 PRI OVER IP SIP TRUNKING TA B L E O F C O N T E N T S 1.1 NETWORK DIAGRAM... 3 1.2 COLLABORATION OF MONARQUE TELECOM... 3 1.3 CONNECTING TO THE DIGIUM G100... 4
Application Note Configuring the Synapse SB67070 SIP Gateway for Broadvox GO! SIP Trunking
Configuring the Synapse SB67070 SIP Gateway for Broadvox GO! SIP Trunking 2012 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed
Application Notes for Configuring Intelepeer SIP Trunking with Avaya IP Office 7.0 - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Intelepeer SIP Trunking with Avaya IP Office 7.0 - Issue 1.0 Abstract These Application Notes describe the procedures for configuring
3COM VCX PBX Server VoIP Intercom Setup Guide
3COM VCX PBX Server VoIP Intercom Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1 is a setup diagram
Application Notes for Configuring Broadvox SIP Trunking with Avaya IP Office - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Broadvox SIP Trunking with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe the procedures for configuring
Configuration guide for Switchvox and Cbeyond.
Configuration guide for Switchvox and Cbeyond. This document will guide a Switchvox administrator through configuring the system to utilize Cbeyond s BeyondVoice with SIPconnect service. After you have
Configuring the PBX Call Routing Table for outbound calls (with security against unsecured calls)
Configuring the PBX Call Routing Table for outbound calls (with security against unsecured calls) The Quadro s Call Routing Table (CRT) defines how incoming and outgoing calls will be handled by the Quadro.
Mediatrix 3000 with Asterisk June 22, 2011
Mediatrix 3000 with Asterisk June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 Network Topology... 3 Equipment Detail... 3 Configuration of the Fax Extension... 4 Configuration
Internet Telephony PBX System
Internet Telephony PBX System T1/E1 Gateway With IP PBX Application Copyright PLANET Technology Corporation. All rights reserved. Case 35: With IP PBX Application Head Office E1 PABX interconnect with
Configuring the CyberData VoIP 4-Port Zone Controller with Audio Out
NetVanta Unified Communications Technical Note Configuring the CyberData VoIP 4-Port Zone Controller with Audio Out Introduction The CyberData Voice over Internet Protocol (VoIP) zone controller enables
Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1 Abstract These Application Notes describe the procedures
Opera System Configuration for Apps
Opera System Configuration for Apps IPhone App Installation and Use Specifications are subject to change without notice. Facilities described may or may not be supported by your network. Opera 240, Opera
Fonality. Optimum Business Trunking and the Fonality Trixbox Pro IP PBX Standard Edition V4.1.2- p13 Configuration Guide
Fonality Optimum Business Trunking and the Fonality Trixbox Pro IP PBX Standard Edition V4.1.2- p13 Configuration Guide Fonality Table of Contents 1. Overview 2. SIP Trunk Adaptor Set-up Instructions 3.
Using the GS8 Modular Gateway with Asterisk
Zed-3 501 Valley Way Milpitas CA 95035 Using the GS8 Modular Gateway with Asterisk Application note, 96-90002-02, May 2008 USA Voice: +1-408-587-9333 Fax: +1-408-586-9038 www.zed-3.com This document is
Configuring the Synapse SB67070 SIP Gateway from AT&T for Clearfly SIP Trunking. January 2013
Configuring the Synapse SB67070 SIP Gateway from AT&T for Clearfly SIP Trunking January 2013 1 Introduction This guide was created to assist Synapse partners with configuring the Synapse SB67070 SIP Gateway
How To Set Up Virtual Fax On Zcoo (U20/50/60/100) On A Pc Or Macbook Or Ipod (U21/50) On An Ipod Or Ipo (U19/50 Or 60
ZYCOO new generation IP Phone system---coovox Series (U20/50/60/100) support virtual fax. Virtual fax is an important feature to help enterprise reduce the cost and promote the efficient communication.
Cisco Unified Communications Manager SIP Trunk Configuration Guide for the VIP-821, VIP-822 and VIP-824
Valcom Network Trunk Ports, models, are compatible with Cisco Unified Communications Manager as either a Third-party SIP Device (Basic or Advanced) or as a SIP Trunk. To preserve the Caller ID information
Analog IP Gateway GXW410x Quick Installation Guide SW version 1.0.0.36
Analog IP Gateway GXW410x Quick Installation Guide SW version 1.0.0.36 Updated 10/24/06 Grandstream Analog IP Gateway GXW410x Quick Installation Guide SW version 1.0.0.36 WARNING: Please DO NOT power cycle
Using the NetVanta 7100 Series
MENU OK CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU MENU OK CANCEL CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU OK CANCEL CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU OK CANCEL CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU OK CANCEL 1 2
IPPBX FAQ. For Firmware Version: V2.0/V3.0 2013-12-11
For Firmware Version: V2.0/V3.0 2013-12-11 Contents 1. IPPBX Access... 3 1.1 How to access IPPBX via SSH?... 3 1.2 How to access IPPBX if I forget the IP of WAN?... 4 1.3 How to retrieve WEB password via
Grandstream Networks, Inc. UCM6510 Basic Configuration Guide
Grandstream Networks, Inc. UCM6510 Basic Configuration Guide Index Table of Contents OVERVIEW... 4 SETUP ENVIRONMENT... 5 QUICK INSTALLATION... 6 CONNECT UCM6510... 6 ACCESS UCM6510 WEB INTERFACE... 6
Grandstream Networks, Inc.
Grandstream Networks, Inc. UCM6100 Basic Configuration Guide Grandstream Networks, Inc. www.grandstream.com TABLE OF CONTENTS OVERIEW... 4 SETUP GUIDE SCENARIO... 4 QUICK INSTALLATION... 5 Connecting the
Application Notes for Configuring Avaya IP Office 9.0 with HIPCOM SIP Trunk Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Avaya IP Office 9.0 with HIPCOM SIP Trunk Issue 1.0 Abstract These Application Notes describe the procedures for configuring
Technical Configuration Notes
MITEL SIPCoE Technical Configuration Notes Configure Mitel UC360 SIP Phone and Mitel MCD for use with VidyoWay SIP CoE 13-4940-00228 NOTICE The information contained in this document is believed to be
3CX Version 8.x - Multiple SIP Trunk configuration to XeloQ Communications / GoAndCall.com
3CX Version 8.x - Multiple SIP Trunk configuration to XeloQ Communications / GoAndCall.com Note: Go to page 13 if you would like to receive multiple DID s on 1 XeloQ SIP Trunk; that is also possible and
Toshiba IPedge. SIP Trunking using the Optimum Business SIP Trunk Adaptor and the Toshiba IPedge IP-PBX
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the Toshiba IPedge IP-PBX Table of Contents 1. Overview 3 2. Prerequisites 3 3. Toshiba IPedge PBX Configuration 3 3.1 SIP Trunking 4 3.2 Stations
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the NEC DSX-40 IP-PBX
SIP Trunking using the Optimum Business SIP Trunk Adaptor and the NEC DSX-40 IP-PBX Table of Contents Overview 3 Prerequisites 3 NEC DSX-40 Configuration 4 Network Settings 4 SIP Programming 5 Extensions/DID
Application Notes for MultiTech FaxFinder FFx40 Software version 1.1.8 with Avaya IP Office 8.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for MultiTech FaxFinder FFx40 Software version 1.1.8 with Avaya IP Office 8.0 Issue 1.0 Abstract These Application Notes describe the configuration
P-2302HWUDL-P1. Quick Start Guide. 802.11g Wireless VoIP Station Gateway. with Built-in DECT Base Station
P-2302HWUDL-P1 802.11g Wireless VoIP Station Gateway with Built-in DECT Base Station Quick Start Guide Version 3.60 Edition 1 3/2007 Overview The P-2302HWUDL-P1 model is a router with IEEE 802.11g wireless
GSM VOIP GATEWAY LEVEL. User Guide. GB 400 010 with GSM module Two-way converter between VoIP and GSM
GSM VOIP GATEWAY GB 400 010 with GSM module Two-way converter between VoIP and GSM User Guide LEVEL 2 Dear customers, Congratulations on purchasing our product - GSM Gateway GB 400 010. You have acquired
Feature and Technical
BlackBerry Mobile Voice System for SIP Gateways and the Avaya Aura Session Manager Version: 5.3 Feature and Technical Overview Published: 2013-06-19 SWD-20130619135120555 Contents 1 Overview...4 2 Features...5
Android Softphone App for the Opera IP System. Installation and user guide
Android Softphone App for the Opera IP System Installation and user guide Android App Manual Specifications are subject to change without notice. Facilities described may or may not be supported by your
Manual. 3CX Phone System for Windows > Version 2.0. Version 2.0 Beta 4
Manual > Version 2.0 Version 2.0 Beta 4 Copyright 2006, 3CX ltd. http://www.3cx.com E-mail: info@3cx.com Information in this document is subject to change without notice. Companies names and data used
Configuring Avaya IP Office 500 for Spitfire SIP Trunks
Configuring Avaya IP Office 500 for Spitfire SIP Trunks This document is a guideline for configuring Spitfire SIP trunks onto Avaya IP Office 500 and includes the settings required for Inbound DDI routing
Application Notes for Configuring Microsoft Office Communications Server 2007 R2 and Avaya IP Office PSTN Call Routing - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Microsoft Office Communications Server 2007 R2 and Avaya IP Office PSTN Call Routing - Issue 1.0 Abstract These Application
Application Notes for Configuring Wesley Clover Solutions Trading Platform with Avaya IP Office using SIP Trunks Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Wesley Clover Solutions Trading Platform with Avaya IP Office using SIP Trunks Issue 1.0 Abstract These Application Notes contain
Application Notes for Multi-Tech FaxFinder IP with Avaya IP Office Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Multi-Tech FaxFinder IP with Avaya IP Office Issue 1.0 Abstract These Application Notes describe the configuration steps required to integrate