PRESSURE REGULATORS GAS LOW PRESSURE BACK PRESSURE
|
|
|
- Lynn Long
- 7 years ago
- Views:
Transcription
1 GAS LOW PRESSURE BACK PRESSURE APPLICATIONS: Control 5 to 20 psig back pressure on low pressure vessels and vent lines of separators, treaters, compressors, and gas gathering systems. CERTIFICATIONS: Canadian Registration Number (CRN): 0C NTY (Ductile) OPERATION: This valve maintains a constant back pressure (upstream of the valve) in the 5 psig to 20 psig range. It has a high degree of sensitivity to upstream changes and extremely fine set-point adjustment capability. The moving parts in this regulator are the Pilot Assembly and the Motor Valve Stem Assembly (crosshatched). The PILOT PLUG consists of two stainless balls rigidly connected. The upper seat for the PILOT PLUG is the Motor Valve Diaphragm Pressure vent (Yellow to Atmosphere). The lower seat for the PILOT PLUG is the Motor Valve Diaphragm Pressure inlet (Red to Yellow). The PILOT SPRING loads the upper side of the Pilot Assembly. Upstream Pressure (Red) opposes the PILOT SPRING from the under side of the Pilot Assembly. Assume a desired pressure setting greater than current Upstream Pressure (Red). The ADJUSTING SCREW compresses the PILOT SPRING. The PILOT SPRING forces the Pilot Assembly downward. The upper seat for the PILOT PLUG (Yellow to Atmosphere) closes. The lower seat for the PILOT PLUG (Red to Yellow) opens. Motor Valve Diaphragm Pressure (Yellow) increases. The Motor Valve Stem Assembly moves downward closing the valve. The Upstream Pressure (Red) increases towards the set pressure. The Pilot Assembly moves upward closing the lower seat (Red to Yellow) then opening the upper seat (Yellow to Atmosphere). The Motor Valve Diaphragm Pressure (Yellow) decreases. Upstream Pressure (Red) acting under the Motor Valve Stem Assembly opens the motor valve. The relief of Upstream Pressure (Red) through the motor valve brings the Pilot assembly to a position closing both seats of the PILOT PLUG. The intermittent vent pilot, threeway valve action of the PILOT PLUG against its seat adjusts the Motor Valve Diaphragm Pressure (Yellow) to reposition the Motor Valve Stem Assembly to accommodate any rate of flow. The rapid but stable repositioning produces a true throttling action. Add Certifications Kimray is an ISO certified manufacturer. A:90.1 Issued 3/16
2 GAS LOW PRESSURE BACK PRESSURE DUCTILE IRON 5-20 psig OPER. PRES. SIZE SCRD FLGD GRVD 2" " " " THRU VALVES AVAILABLE: PART BODY OPER. MAX REP. NO. CONNECTION MODEL NO. PRES. W.P. KIT AOD 2" NPT 202 SGT BP RUI AOE 2" 150RF 202 FGT BP RUI AOF 2" GRVD. 202 GGT BP RUI AOG 3" NPT 302 SGT BP RUJ AOH 3" 150RF 302 FGT BP RUJ AOJ 4" NPT 402 SGT BP RUK AOK 4" 150RF 402 FGT BP RUK AON 6" 150RF 602 FGT BP RUP NOTES: *These parts are recommended spare parts and are stocked as repair kits. The numbers of a series assigned to a part indicate different line sizes. For example: Stem 137-1", 138-2", 139-3", 140-4", 141-6". For standard & optional Seals, Metals, Cv values, Material specifications & Dimensions see Technical Data on pages A:I - A:V Standard Trim size is same as connection size. For Reduced trim sizes, see A:I Max W.P. valves based on -20 F to 100 F. See page A:V for temps above 100 F A:90.2 Kimray is an ISO certified manufacturer. Page Redesign
3 FLOW COEFFICIENT Table 1 - Flow Coefficient(Cv) at % stem travel for Pilot Operated Regulators 1" Pressure Regulator in.(mm) 1/2 in (12mm) Reduced in (25mm) Full Port " Pressure Regulator 1 1/4 in (31 mm) Reduced in Removable Full Port * in (50 mm) Full Port * " Pressure Regulator 1 5/8 in (66 mm) Reduced in (76 mm) Full Port " Pressure Regulator 2 in (50 mm) Reduced in (100 mm) Full Port " Pressure Regulator 3 in (76 mm) Reduced in (152 mm) Full Port Kimray flow equations conform to ANSI/ISA Kimray inherent flow characteristics conform to ANSI/ISA * Use "2 inch Removable Full Port" values for regulators with operating pressure ranges of psig, psig & psig A:I
4 DIMENSIONS FOR: BACK PRESSURE UPSTREAM DIFFERENTIAL PRESSURE PRESSURE REDUCING-BALANCED PRESSURE REDUCING VACUUM PRESSURE DIFFERENTIAL PRESSURE REDUCING BACK PRESSURE VACUUM LIQUID BACK PRESSURE G DUCTILE 250 S/FGT-BP-S FOR: LOW PRESSURE BACK PRESSURE OUNCES BACK PRESSURE TO VACUUM OUNCES PRESSURE REDUCING OUNCES PRESSURE REDUCING VACUUM VACUUM BACK PRESSURE TO VACUUM DUCTILE LINE SIZE BODY SIZE A B C D * E F G H * I 1" NPT 4 3/8" 1 1/8" 7 1/2" 11 5/8" 3 1/4" 2" 250 S/FGT 3" 4" NPT 8 1/2" 2 1/8" 11 1/2" 10 1/2" 6 1/2" FLANGED 9" 3" 11 1/2" 10 1/2" 6 1/2" 9 1/8" 14 1/2" 14" GROOVED 8 3/4" 2 1/8" 11 1/2" 10 1/2" 6 1/2" NPT 10 1/2" FLANGED 10 3/8" NPT 12 1/16" 3 1/16" 13" 12" 8 1/2" FLANGED 12 3/16" 3 3/4" 13" 12" 8 1/2" 12 3/8" 16 1/2" 15 1/2" NPT 15" 1/16 4" 14 1/2" 13 3/16" 10 1/2" FLANGED 15 1/16" 4 1/2" 14 1/2" 13 3/16" 10 1/2" 15 1/16" 18 1/2" 16 11/16" 6" FLANGED 22" 5 1/2" 17" 17 7/8" 16" 21 15/16" 20 1/2" 18 3/8" FLANGE DIMENSIONS ARE ANSI 125/150 STANDARD. *Add 7/8" to Pressure Reducing Balanced and Up Stream Differential Pressure Regulators for this dimension. A:II Configuration of Back Pressure Valve is a trademark of Kimray, Inc.
5 SEALS Table 2 - Seal Options Part Standard Material Optional Material Pilot Diaphragm Seat Nitrile FKM, HSN, AFLAS, Gylon O-rings Nitrile FKM, HSN, AFLAS, Gylon All Diaphragms Except Pilot Diaphragm Nitrile FKM, HSN, AFLAS, Gylon Diaphragm Pilot Diaphragm Polyurethane FKM, HSN, AFLAS, Gylon Diaphragm O Ring Seat Resistance Properties Table 3 - Seal Specifications NITRILE HIGHLY POLY- SATURATED FKM AFLAS URETHANE NITRILE GYLON Kimray Suffix - HSN V AF P GY Abrasion G G G GE E E Acid F E E E P E Chemical FG FG E E FG E Cold G G PF P G E Flame P P E E P P Heat G E E E F E Oil E E E E G E Ozone P G E E E E Set GE GE E PF F P Tear FG FG F PF GE E Water/Steam FG E P GE P E Weather F G E E E E CO2 FG GE PG GE G E H2S P FG P E G E Methanol G E PF PF P E Dynamic GE GE GE GE E P Electrical F F F E FG E Impermeability G G G G G E Tensile Strength GE E GE FG E E Temp. Range ( F) -40 to +220 F -15 to +300 F -10 to +350 F +25 to +450 F -40 to +220 F -350 to +500 F Temp. Range ( C) -40 to +105 C -26 to +149 C -23 to +177 C 0 to +232 C -40 to +104 C -212 to +260 C Form O,S,D O,S,D O,S,D O,S,D S,D S,D RATINGS: P-POOR, F-FAIR, G-GOOD, E-EXCELLENT Configuration of Back Pressure Valve is a trademark of Kimray, Inc. A:III
6 MATERIAL SPECIFICATION Table 5 - Materials of Construction Part Description Valve Size Standard Material Optional Material(s) Ratio Plug Seat Disc 1" & 2" 316 Powdered Metal SS-316NI-25 N/A 1" & 2" Reduced Trim Steel, ASTM A Stainless Steel ASTM A-479 3" Powdered Metal F Stainless Steel ASTM A-479 4" & 6" Ductile, ASTM A Stainless Steel ASTM A-479 1" Powdered Metal F Stainless Steel ASTM A-479 2", 3" & 4" Ductile, ASTM A-395 Stainless Steel ASTM A-351 CF8M 6" Ductile, ASTM A-395 Stainless Steel ASTM A-240 Stem 1" thru 6" 303 Stainless Steel, ASTM A Stainless Steel ASTM A-479 Body 1" thru 6" Ductile, ASTM A-395 N/A Body 2" thru 6" Steel, ASTM A-216 WCB Stainless Steel ASTM A-351 CF8M Tubing Removable Seat 175 W.P. or Less Copper Tubing ASTM B-380 UNS C Stainless Steel ASTM A-213 Copper Tubing ASTM B-280 UNS C Stainless Steel ASTM A-213 Greater Than 175 W.P. 304 Stainless Steel ASTM A Stainless Steel ASTM A-213 2" thru 6" Ductile Body Ductile, ASTM A-395 Stainless Steel ASTM A-351 CF8M 2" thru 6" Steel Body Stainless Steel ASTM A-351 CF8M N/A Stem Tubing Seat Disc Ratio Plug Body Table 4 - Material Specification Body Inner Parts CAST CAST DUCTILE 303 STAINLESS 316 STAINLESS 17-4 PH STAIN- LESS KIMRAY SUFFIX CS CD SS6 SS6 PH ASTM GROUP ASTM A-216 ASTM A-395 ASTM A-582 ASTM A-479 ASTM A-564 GRADE WCB UNS J03002 F32800 S30300 S31600 S17400 NACE Compliant Yes Yes No Yes Yes A:IV Configuration of Back Pressure Valve is a trademark of Kimray, Inc.
7 TEMPERATURE Table 6 - Temperature vs. Pressure Rating Flange Class ASTM Class 150 RF Temperature F ( C) Static Test Pressure (psig) 450 (31 bar) Maximum Allowable Non-Shock Pressure (psig) CAST DUCTILE ASTM A-395 Flange Class 150 RF -20 to 100 (-28 to 37) 250 (17.2 bar) 200 (93) 235 (16.2 bar) 300 (148) 215 (14.8 bar) 400 (204) 200 (13.7 bar) 500 (260) 170 (11.7 bar) 600 (315) 140 (9.6 bar) 650 (343) 125 (8.6 bar) 700 (371) CAST ASTM A WCB Flange Class 150 RF -20 to 100 (-28 to 37) 285 (20.0 bar) 200 (93) 260 (17.9 bar) 300 (148) 230 (15.9 bar) 400 (204) 200 (13.8 bar) 500 (260) 170 (11.7 bar) 600 (315) 140 (9.7 bar) 650 (343) 125 (8.6 bar) 700 (371) 110 (7.6 bar) FLANGED (150RF) SCREWED (NPT) GROOVED Kimray valves conform to ASME B for working pressure vs working temperature & ASME B for flanges and flanged fittings. Configuration of Back Pressure Valve is a trademark of Kimray, Inc. A:V
PRESSURE REGULATORS GAS BACK PRESSURE
PRESSURE REGULATORS GAS BAK PRESSURE APPLIATION: Vent lines on oil separators, flow treaters, compressor stations, gas gathering systems. PRESSURE RANGE: ast Iron: 5 psig to 125 psig Ductile Iron: 10 psig
1805 Series Relief Valves
October 2011 1805 Series Relief Valves P1026 1805G Type 1805-2 Type 1805-4 Figure 1. Typical 1805 Relief Valves Introduction The 1805 Series relief valves are designed for use in farm tap applications
Types 66R and 66RR Low-Pressure Relief Valves
November 2009 Types 66R and 66RR Low-Pressure Relief Valves W1953 W1908 TYPE 66R RELIEF VALVE TYPE 66RR RELIEF VALVE Figure 1. Typical Constructions Introduction Types 66R and 66RR low-pressure throttling
Baumann 24003 3 Way Bronze or Stainless Steel Control Valve
Product Bulletin D1039X012 24003 Valve Baumann 24003 3 Way Bronze or Stainless Steel Control Valve 3 Way Rugged Industrial Control Valve For Mixing and Diverting Applications The Baumann 24003 3 way control
Mustang Series PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE. M115-2 (Globe) M1115-2 (Angle) Schematic. Standard Components
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Throttles to maintain minimum upstream pressure PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE
PRESSURE REDUCING CONTROL VALVE
Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING CONTROL VALVE with LOW FLOW BY-PASS FEATURE Main Line
API Flanged Safety Relief Valves Series 526 CATALOG
API Flanged Safety Relief Valves Series 26 CATALOG The-Safety-Valve.com 1 Valve finder How to find the right product group High operating to set pressure ratio, high backpressure or low total height? Yes
REGULATORS D& HD Series
Watson McDaniel reserves the right to change the designs and/or materials of its products out notice. 2002 Watson McDaniel Company Ductile Iron body - HD Series Full port strainer & blowdown valve on pilot
REGULATORS 175/153 Series
175/153 Series 175 HEATING 153 COOLING Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2002 Watson McDaniel Company Revised 7/2002 175 / 153 Screwed
Shut-off & Lockout Valves 1/4" to 1-1/2" port size
Section 16 Shut-off & Lockout Valves 1/4" to 1-1/2" port size Contents T72 Excelon Shut-off & Lockout Valves 1/4", 3/8" Port Sizes....................................ALE-16-2 T73 Excelon Shut-Off & Lockout
CHEXTER TM FITS YOUR APPLICATION, PROFITABLY
CHEXTER TM FITS YOUR APPLICATION, PROFITABLY Commercial Construction CHEXTER TM Check Valves are economically used in chilled and hot water air conditioning systems, refrigeration and other piping and
2-Port Self-acting Temperature Control Valve Selection for Heating and Cooling Applications
Page 1 of 12 TI-S21-07 CH Issue 1 Cert. No. LRQ 0963008 ISO 9001 2-Port Self-acting Temperature Control Valve Selection How to select a system Valve selection: 1. Is the application for heating or cooling?
167D Series Switching Valves
June 2011 167D Series Switching Valves P1185 P1184 167D TWO-WAY SWITCHING VALVE 167DA THREE-WAY SWITCHING VALVE Figure 1. 167D Series Switching Valves Introduction The 167D Series switching valves are
Baumann 87000 Flexsleev Sanitary Control Valve
Product Bulletin D103345X012 Baumann 87000 Flexsleev Sanitary Control Valve The Baumann 87000 control valve (figures 1 and 2) is excellent for throttling high purity liquid or gaseous media commonly found
2 WAY (2/2) AND 3 WAY (3/2) BRASS AND STAINLESS STEEL SOLENOID VALVES
2 WAY (2/2) AND 3 WAY (3/2) BRASS AND STAINLESS STEEL SOLENOID VALVES DIRECT ACTING Brochure N-289 SPECIFICATIONS Port Size: 1/8 and1/4 Solenoid Valve for air, oil, water and other fluids Flow Direction:
Pressure & Flame Protection
Pressure & Flame Protection Safety Relief Valves Safety Relief Valves WB SERIES SPRING LOADED SAFETY RELIEF VALVES The WB is designed safely relieve excess pressure in pumps, pipework, tanks, calorifiers,
Automatic Self-Cleaning Strainers
Applications Water and Liquid service Power Industry Cooling water Pulp & Paper Removing fibers Process Equipment Protect equipment Metal & Mining Quenching, blast furnace cooling Automatic Self-Cleaning
Vacuum Control. Vacuum Applications. Vacuum Regulators. Vacuum Breakers (Relief Valves) Vacuum Control Devices. Vacuum Terminology
Vacuum Applications Vacuum regulators and breakers are widely used in process plants. Conventional regulators and relief valves might be suitable for service if applied correctly. This section provides
Type 92S Pilot-Operated Steam Regulator
Type 92S Pilot-Operated Steam Regulator Introduction The Type 92S steam regulator is piston actuated for high cycle steam service which includes a Type 6492L, 6492H or pilot (see Figure 1). These pilots
V47 Series Temperature Actuated Modulating Water Valves
V47 Series Temperature Actuated Modulating Water Valves Master Catalog 125 Valves, Miscellaneous (Other Than Gas) Section V Product Bulletin V47 Issue Date 0286 Application The V47 modulating valves regulate
Fisher 377 Trip Valve
377 Trip Valve Product Bulletin Fisher 377 Trip Valve Fisher 377 pressure sensing trip valves are for control applications where a specific valve/actuator action is required when supply pressure falls
BERMAD Waterworks. Pressure Relief/Sustaining Valve. 700 Series. Model 730. Features and Benefits. Major Additional Features
Pressure Relief/Sustaining Valve Prioritizing pressure zones Ensuring controlled pipeline fill-up Preventing pipeline emptying Pump overload & cavitation protection Safeguarding pump minimum flow Excessive
Type EZR Relief Valve or Backpressure Regulator
October 2015 Type EZR Relief Valve or Backpressure Regulator Internally Actuated quiet Operation Exceptional Design Thoroughly Tested Robust Construction NPS 1, 2, 3, 4, 6 and 8 / DN 25, 50, 80,, 150 and
Series 240 Type 3244-1 and Type 3244-7 Pneumatic Control Valves Type 3244 Three-way Valve
Series 240 Type 3244-1 and Type 3244-7 Pneumatic Control Valves Type 3244 Three-way Valve DIN and ANSI versions Application Mixing or diverting valve for process engineering and industrial applications
CCI 100 DPC DRAG Wellhead Production Choke Valve
CCI 100 DPC DRAG Wellhead Production Choke Valve 2 Severe service DRAG choke valve delivers precise wellhead pressure control with superior reliability and life. Improves well production time Enhances
Commercial & Industrial Propane Regulators and Meters
Commercial & Industrial Propane Regulators and Meters Master Distributor for First Stage Regulators P32* Field adjustable 60 Mesh screen on inlet 1/4 FNPT 250 PSI Excellent stability P37* Patented balance
Flow controller with integrated control valve (PN 16, 25, 40*) AFQM, AFQM 6 - return and flow mounting
Data sheet Flow controller with integrated control valve (PN 16, 5, 40*) AFQM, AFQM 6 - return and flow mounting Description AFQM 6 DN 40, 50 AFQM DN 65-15 AFQM DN 150-50 AFQM(6) is a self-acting flow
MFP14, MFP14S and MFP14SS Automatic Pumps
Page 1 of 6 TI-P136-02 ST Issue 12 Cert. No. LRQ 0963008 ISO 9001, S and SS utomatic Pumps Description The Spirax Sarco automatic pump is a displacement receiver operated by steam or compressed air. It
Vogt Valves The Connection Bulletin for Extended Body Forged Steel Valves Welded Bonnet, Bolted Bonnet, Class 800 & Class 1500 CB 22
The Connection Bulletin for Extended Body Forged Steel Valves Welded Bonnet, Bolted Bonnet, Class 800 & Class 1500 CB 22 Extended Body Forged Steel Valves An extended body gate valve specifically designed
ISORIA. Centered disc butterfly valves with AMRING elastomer liner. 240 PSI: 1½ to8. 150 PSI : 10 to 24
Type series booklet 8448.1/2-EN--US ISORIA Centered disc butterfly valves with AMRING elastomer liner 240 PSI: 1½ to8 150 PSI : 10 to 24 Design in accordance with ISO 10631 Manual, electrical, pneumatical
TYPE E Main Valve Sizes 3 /8 through 12
SD 3001F PRINTED IN U.S.A. SD 3001F/0707 A B TYPE E MAIN VALVE C D E TYPE E Main Valve Sizes 3 /8 through 12 The Spence Type E Main Valve is of normally closed, single seat design featuring packless construction,
BERMAD Waterworks. Quick Active Check Valve. 700 Series. Model 740Q. Features and Benefits. Major Additional Features
Booster Pump Control Valve Quick Active Check Valve Isolates system from the effects of pump starts and stops for: Solitary single speed pumps Battery of single speed pumps (add & switch) Battery of variable
GS-General Service Control Valves
GS-General Service Control Valves GS-General Service Valves The GS-General Service Valves continue Copes-Vulcan s tradition of designing and manufacturing control valves that provide both exceptional service
PRESSURE REDUCER AND RELIEF VALVES WITH METALLIC BELLOW FOR WATER STEAM
PRESSURE REDUCER AND RELIEF VALVES WITH METALLIC BELLOW FOR WATER STEAM PRESSURE REDUCER AND RELIEF VALVES These devices are used to reduce and control a gaseous flow pressure (air, steam, gas ). The PRESSURE
Type EZL Pressure Reducing Regulator for Low Differential Pressure Applications
Type EZL Pressure Reducing Regulator for Low Differential Pressure Applications May 2016 W8962 Figure 1. Type EZL Pressure Reducing Regulator Features Main Diaphragm The main diaphragm is Nitrile (NBR)
ball valves Flomite 71 Series 2-way Integral Panel Mount Ball Valves
2-way Integral Panel Mount Ball Valves Used for quick on-off service with a visual indication of flow, HOKE s 2-way ball valves offer orifice sizes up to 0.25 (6.4mm). Flomite valves feature a floating
Spira-trol TM Two-port Control Valves EN Standard KE, KF and KL DN15 to DN300 and ASME Standard KEA, KFA and KLA ½" to 12"
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
Proportional Relief Valves
www.swagelok.com Proportional Relief Valves R Series Liquid or gas service Set pressures from 10 to psig (0.7 to 413 bar) 1/4 and 1/2 in. and 6 to 12 mm end connections 2 Proportional Relief Valves Spring
Valves, Automation & Controls. series 84 /99 HIGH PERFORMANCE 3-PIECE BALL VALVE REDUCE & FULL PORT, STANDARD & FIRE SAFE. www.sharpevalves.
Valves, Automation & Controls series 8 /99 & FS8 /FS99 HIGH PERFORMANCE -PIECE BALL VALVE REDUCE & FULL PORT, STANDARD & FIRE SAFE www.sharpevalves.com Design & Features SHARPE VALVES - SERIES 8/99 Fire
5.23.22 STEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD PART 1: GENERAL. 1.01 Purpose:
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
KF Needle & Gauge Valves
KF Needle & Gauge Valves Superior Fluid Control Products KF O-Ring & Packed Stem Style Needle Valves KF Needle Valves combine rugged construction, dependability and leak-free performance at high and low
DARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
SECTION 15062 STEAM AND CONDENSATE PIPING PART 1 DESIGN DIRECTIVES 1.1 QUALITY ASSURANCE A. Comply with the provisions of the following: 1.2 DESIGN CRITERIA 1. ASME B 31.9 Building Services Piping : for
Morrison Bros. Co. General Product Specifications
Morrison Bros. Co. General Product Specifications Tank Mounted Spillbox The spill containment device is manufactured to contain spills and drips that may occur at the fill point on aboveground storage
1800C and 1800C-HC Series Service Regulators. Technical Bulletin
and -H Series Service Regulators Technical Bulletin and -H Series Service Regulators 0 Elster American Meter The Series pressure regulators are designed to control natural gas, air, nitrogen, carbon dioxide,
Specification Data CM37002 09/10. Putting You In Control. 37002 Series MiniTork ll Control Valves. Heavy Duty Control Butterfly Valves
Putting You In Control Specification ata CM37002 09/10 37002 Series MiniTork ll Control Valves Heavy uty Control Butterfly Valves resser Masoneilan 37002 Series MiniTork II Control Valves Heavy uty Control
EZR Series Pressure Reducing Regulator
EZR Series Pressure Reducing Regulator November 2015 Robust Quiet Operation Thoroughly Tested Exceptional Design W7399 TYPE EZR REGULATOR Internally Actuated W8136 TYPE EZROSX WITH INTEGRAL SLAM-SHUT DEVICE
Fisher CV500 Rotary Globe Control Valve
CV500 Valve D101606012 Product Bulletin Fisher CV500 Rotary Globe Control Valve The Fisher CV500 Cam Vee-Ball control valve combines the rangeability of the cammed-segmented V-notched ball, with the inherent
Solenoid valves 2/2-way direct-operated Type EV210A
Solenoid valves 2/2-way direct-operated Type EV210A Features EV210A NC and NO Very compact valves for industrial application, such as control and dosage For water, oil, compressed air and similar neutral
1301 Series High-Pressure Regulators
1301 Series High-Pressure Regulators Bulletin 71.1:1301 December 2013 P10 Figure 1. Type 1301F Regulator Features Durable Stainless Steel Diaphragm For high-outlet pressure applications. Spare Valve Disk
3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223
3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223 HERION S HIGH PERFORMANCE POPPET VALVES For those applications requiring high Cv, fast response times, large
Product Manual. CVS Type 67AFR Filter Regulator. Introduction. Installation. Description
Product Manual CVS Type 67AFR Filter Regulator Introduction This CVS Controls product manual includes instructions for the installation, adjustment, maintenance and parts ordering of the CVS Type 67AFR
Style 07 Zero Flex Rigid Coupling. Style 75 Flexible Coupling. Style 77 Flexible Coupling 11. Description
Style 07 Zero Flex Rigid Coupling The unique angled pad design adjusts to standard pipe tolerances to positively clamp the pipe to resist flexural and torsional loads. Working pressures are based on standard
PLUMBING RE-SUBMITTAL 22 11 17
PLUMBING RE-SUBMITTAL 22 11 17 ACADEMIC BUILDING & PATRIOT S CASA TEXAS A&M UNIVERSITY - SAN ANTONIO, TX NO. 25-3122, VAC NO. 39019 OWNER: ARCHITECT: MEP ENGINEER: GENERAL CONTRACTOR: PLUMBING CONTRACTOR:
289 Series Spring-Loaded Relief Valves
October 14 89 Series Spring-Loaded Relief Valves W187_1 W1871 TYPE 89L 1 NPT TYPES 89H AND 89HH W187 NPT TYPE 89H W187_ TYPES 89U AND 89A Figure 1. Types 89H, 89L and 89U Relief Valves Introduction The
MODEL 201 225LP 225LP2 225LP4 Safety Relief Valves
Edition GDRV.06 BRYAN DONKIN RMG CANADA LIMITED Serving the Gas Industry WORLDWIDE Applications Specifically designed to protect the downstream system or equipment from over pressure conditions by discharging
Fisher D3 Control Valve
D3 Valve Product Bulletin Fisher D3 Control Valve The Fisher D3 control valve is a compact, rugged valve designed for on/off or throttling control, and utilizes FloPro technology, using either pneumatic
Best Under Pressure 2900 MPV. Pilot-Operated Safety Relief Valve. www.dresser.com. 2900 MPV Oct 2008-CO
Best Under Pressure 0 MPV PilotOperated Safety Relief Valve www.dresser.com 0 MPV Oct 2008CO 0 MPV 0 Pilot Operated Relief Valve Consolidated offers a unique pilot valve design that combines p performance,
Type 119 Control Valve
Instruction Manual Form 5204 Type 119 December 2009 Type 119 Control Valve Introduction Scope of the Manual This instruction manual provides installation, spring adjustment, maintenance, and parts information
Type 99 Pressure Reducing Regulator
Bulletin 7: February 2016 Type Pressure Reducing Regulator W27 W76 Figure 1. Typical Type Regulator Introduction The Type gas regulators provide a broad capacity for controlled pressure ranges and capacities
Assisted lift operated 2/2-way solenoid valves Type EV250B
MAKING MODERN LIVING POSSIBLE Data sheet Assisted lift operated 2/2-way solenoid valves Type EV250B EV250B with assisted lift can operate from zero and up to 10 bar differential pressure. This 2/2-way
% ^ ) 0.55 W Low Power Solenoid Valves Aluminum, Brass, or Stainless Steel Bodies 1/4" to 1" NPT. 2/2 3/2 4/2 5/2 5/3 SERIES Low Power
.55 W Solenoid Valves Aluminum, Brass, or Stainless Steel Bodies /" to " NPT / 3/ / 5/ 5/3 Features Molded one-piece solenoid with highly efficient solenoid cartridge and.55 W low wattage coil Standard
Thermostatic valve Type AVTA
MAKING MODERN LIVING POSSIBLE Data sheet Thermostatic valve Type AVTA Thermostatic valves are used for proportional regulation of flow quantity, depending on the setting and the sensor temperature. The
Baumann 81000 Mikroseal Control Valve
Product Bulletin D103340X012 Baumann 81000 Mikroseal Control Valve The Baumann 81000 Mikroseal control valve (figures 1 and 2) is excellent for throttling of liquid or gaseous media, particularly where
MAKING MODERN LIVING POSSIBLE. Thermostatic valve AVTA. Technical brochure
MAKING MODERN LIVING POSSIBLE Thermostatic valve AVTA Technical brochure 2 IC.PD.500.A3.02-520B3728 Danfoss A/S 07-2009/ RA-MC/mr Contents Page Features............................................................................................4
The Unique Accelabar Flow Meter
The Unique Accelabar Flow Meter The Accelabar is a new and unique flow meter that combines two differential pressure technologies to produce operating ranges never before attainable in a single flow meter.
ENERGYPETROL S.A. STOCK DE MATERIALES PARA ENTREGA INMEDIATA SALVO VENTA PREVIA
1 GA01011XU-3" Gate Valve 3" ANSI 150 RF Flanged Carbon Steel Body per ASME B16.5 and Bonnet ASTM A216 Gr WCB,, OS&Y, Bolted Bonnet, Flexible Wedge Gate, trim 8 and HF Stellited Seats. Gear operated. With
Ve-Lock manufactures Needle Valves from Solid bar stock Materials & all parts details are as below:
Needle Valves : - Needle valves have a slender, tapered point at the end of the valve stem that is lowered through the seat to restrict or block flow. Fluid flowing through the Needle valve turns 90 degrees
Section 4: NiResist Iron
Section 4: NiResist Iron Section 4 Ni-Resist Description of Grades...4-2 201 (Type 1) Ni-Resist...4-3 202 (Type 2) Ni-Resist...4-6 Stock Listings...4-8 4-1 Ni-Resist Description of Grades Ni-Resist Dura-Bar
Nozzle Check Valves. NOREVA nozzle check valves are used
Nozzle Check Valves NOREVA nozzle check valves are used in applications where the reverse flow of a fluid has to be avoided. These valves are suitable for all kind of liquid and gaseous fluids and fire
TECHNICAL BULLETIN. Kämmer LinedFlow - 132000 Corrosive Application Valves. Experience In Motion FCD KMENTB3221-01 04/12
TECHNICAL BULLETIN Kämmer LinedFlow - 132000 Corrosive Application Valves FCD KMENTB3221-01 04/12 Experience In Motion Description ¼-inch NPT test port Large guided stem area Bellows seal eliminates stem
RMF Engineering 23 05 23
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
Ball Valves (HB Series) Catalog 4121-HB Revised, April 2005
Ball Valves (HB Series) Revised, April 2005 Introduction Parker High Pressure HB4 Series Ball Valves provide reliable shut-off or switching functions. The upper and lower trunnion bearings enhance the
Plate heat exchanger. Applications General heating and cooling duties. Heating by means of steam.
M3 Plate heat exchanger Applications General heating and cooling duties. Heating by means of steam. Standard design The plate heat exchanger consists of a pack of corrugated metal plates with portholes
G. VULCANIZED SEAT Pressure sensitive seating with full disc overlap provides positive seating at high and low pressures.
A B C D G F E J H I A. RETAINER PLUGS Retain hinge and stop pins while providing compression to stabilization spheres. B. STABILIZATION SPHERES Stabilize hinge and stop pins, preventing vibration and wear.
FLANGED END BALL VALVE
Specification: FLANGED END BALL VALVE - Chem Oil s two-piece ball valve has been designed to handle extreme service applications with unsurpassed reliability. Valve body machined from solid wrought material
AUTOMATIC CHANGEOVER MANIFOLD Series 915
AUTOMATIC CHANGEOVER MANIFOLD Series 915 FEATURES Fully automatic, simple, hassle-free operation No variance in delivery pressure Designed for ultra high purity gas service Built-in audio and visual alarm
S GATE KNIFE GATE VALVE WITH PNEUMATIC ACTUATOR
MAIN FEATURES The pneumatic S GATE knife gate valve is intended for the automatic shut off of pipes of the heavy fluids like slurries and powders. The main fields of application are the water treatment,
Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation
Instruction Manual 1052 Size 20 Actuator (F & G) Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation Contents Introduction... 1 Scope of manual... 1 Description... 1 Specifications...
Self-operated Pressure Regulators Universal Pressure Reducing Valve Type 41-23
Self-operated Pressure Regulators Universal Pressure Reducing Valve Type 41-23 Application Pressure regulators for set points from 5 mbar to 28 bar Valves in nominal sizes DN 15 to 100 Nominal pressures
Stainless Steel Valves For the Sanitary Industries
www.swagelok.com Stainless Steel Valves For the Sanitary Industries Sanitary ball valves Manual and pneumatically actuated butterfly valves Disk and ball check valves ir blow check valves ir relief valves
Fisher 657 and 667 Diaphragm Actuators
657 and Actuators Product Bulletin Fisher 657 and Diaphragm Actuators Fisher 657 and spring-opposed diaphragm actuators position the valve plug in the valve in response to varying controller or valve positioner
AIR LINE VALVES AND GAUGES
AIR LINE VALVES AND GAUGES INGERSOLL-RAND AIR LINE VALVES AND GAUGES Maintaining consistent air pressure throughout the entire system is crucial for maximum performance and productivity. Ingersoll-Rand
These features have made Lo Torc valves the choice of high pressure plug value users, worldwide:
LO TORC Plug Valve The high value, dependable performance, and low maintenance requirements of Halliburton Lo Torc valves can help reduce overall operating costs and help cut downtime. These features have
4 Posiflow Proportional Solenoid Valves
4 Posiflow Solenoid Brass or Stainless Steel Bodies 1/4" to 1/2" NPT 2/2 Features Flow rates adjustable between 0% and 100% of rating Flow rate can also be regulated by a range of electrical inputs (sensors,
Air Eliminators and Combination Air Eliminators Strainers
Description Air Eliminators and Combination Air Eliminator Strainers are designed to provide separation, elimination and prevention of air in piping systems for a variety of installations and conditions.
Constantemp Double Wall Low pressure steam-water Heater F-340LDW,F-640LDW, F-940LDW and F-1240LDW
Installation, Operating and Maintenance Instructions 90/4.5.5 Rev. 0 Constantemp Double Wall Low pressure steam-water Heater F-340LDW,F-640LDW, F-940LDW and F-1240LDW Table of Contents SECTION I... 2 INSTALLATION...
Baumann 24000 Little Scotty Bronze Control Valve
24000 Valve Product Bulletin Baumann 24000 Little Scotty Bronze Control Valve Baumann Little Scotty industrial control valves are intended for general utility service in pressure, flow, and temperature
How To Order A Direct Flow Air Cleaner
Reduced Volume - Improved Performance - Flexible Packaging The patented Direct Flow technology provides the flexibility to optimize the air system performance to size ratio, meeting the demands of today
Equivalents & Conversion Factors 406 Capacity Formulas for Steam Loads 407 Formulas for Control Valve Sizing 408-409
Engineering Data Table of Contents Page No. I II Formulas, Conversions & Guidelines Equivalents & Conversion Factors 406 Capacity Formulas for Steam Loads 407 Formulas for Control Sizing 408-409 Steam
Pressure and Temperature Controls
Pressure and Controls Pressure Reducing Armstrong pressure reducing valves (PRVs) and temperature regulators help you manage steam, air and liquid systems safely and efficiently. And assure uninterrupted
BERMAD Waterworks. High Pressure, Surge Anticipating Control Valve. 800 Series. Model 835-M. Features and Benefits. Major Additional Features
High Pressure, Surge Anticipating Control Valve Eliminates surge in all pumping systems: Booster & deep well, single & variable speed Eliminates surge in all distribution networks: Municipal, high-rise
SLAM-SHUT VALVE. Type OSE. Europe, Middle East, Africa and Asia Pacific Documents Only. Process Management TM
SLAM-SHUT VALVE Type OSE Process Management TM DESCRIPTION The purpose of the OSE slam shut valve is to totally and rapidly cut off gas flow when the outlet pressure exceeds or drops below the setting.
High CATALOG. LESER worldwide. Performance. Flanged Safety Relief Valves Series 441 Series 441 Full nozzle Series XXL Series 444 Series 458
LESER UK Bristol sales@leser.co.uk LESER Germany Hamburg and Hohenwestedt sales@leser.com André Ramseyer AG Flamatt, Switzerland info@ramseyer.ch LESER China Tianjin, Beijing, Shanghai and Shenzhen sales.china@leser.com
DOUBLE SEAT BRONZE BODY HIGH CAPACITY
PS593DB HEAVY DUTY BRONZE GLOBE CONTROL VALVES DB DOUBLE SEAT BRONZE BODY HIGH CAPACITY 1, 1-1/4, 1-1/2, and 2 Union Ends ANSI Class 250 Body Rating ANSI Class II Close off Bronze or Stainless Steel Trim
Typical Aluminum GFM Mass Flow Meter
MASS FLOW METERS Design Features n Rigid metallic construction. n Maximum pressure of 1000 psig (70 bars). n Leak integrity 1 x 10-9 of helium. n NIST traceable certification. n Built-in tiltable LCD readout.
Model 4418F. www.amot.com. Overview. Typical applications. Key features and benefits. Accreditations. Starting air/gas valve Vented fuel gas valve
High Pressure Control Valve Model 4418F Overview The 4418F has been designed specifically for use as an air start valve for diesel engines or as a fuel shut-off valve for gas turbine applications. Its
Self-contained valve functions as integral check valve, flow sensing element and bypass control valve.
Self-contained valve functions as integral check valve, flow sensing element and bypass control valve. Features Eliminates high cost of installation and maintenance of complex conventional flow control
DESIGN STANDARDS SECTION 23 60 00
PART 1 - GENERAL 1.01 Work included: A. Piping, tubing and fittings. B. Piping specialties. C. Special duty valves. D. Refrigerants. E. Chillers. F. Refrigerant monitors. 1.02 General requirements: A.
Float and Thermostatic Traps Series H, C and X
Hoffman Specialty Installation & Maintenance Instructions HS-(E) and Thermostatic Traps Series H, C and X Series C & NPT Series C NPT Series X NPT Series C NPT Series H Ratings Maximum Max. Operating NPT