MINI MCR-SL-RPSS-I-I(-SP)

Transcription

1 Repeater power supply HART INTERFACE Data Sheet 00_en_00 Description PHOENIX CONTACT - 0/007 Features The 6. mm wide MINI MCR-SL-RPSS-I-I... repeater power supply supplies transmitters in the field and electrically isolates the input signal from the output signal. HART data protocols can be transmitted bidirectionally. The module can be used in both isolator and repeater power supply operation. Electrically isolated ma or...0 ma analog standard signals are available on the input and output side. The power supply (0. V DC to 0 V DC) can be supplied via connection terminal blocks on the modules or in conjunction with the DIN rail connector ma or...0 ma input and output signal range Can be supplied with screw or spring-cage connection WARNING: Correct usage in potentially explosive areas The module is a category item of electrical equipment. Follow the instructions provided here during installation and observe the safety instructions. Make sure you always use the the latest documentation. It can be downloaded at A conversion table is available on the Internet at This data sheet is valid for all products listed on the following page:

2 Ordering data Description Type Order No. Pcs./Pkt. Repeater power supply HART, screw connection, with HART protocol MINI MCR-SL-RPSS-I-I 6079 Repeater power supply HART, spring-cage connection, with HART protocol MINI MCR-SL-RPSS-I-I-SP 00 Accessories Type Order No. Pcs./Pkt. DIN rail connector (T-BUS), 5-pos., for bridging the supply voltage, can be snapped onto NS 5/... DIN rails according to EN 6075 MINI MCR power terminal block, with screw connection, current consumption up to A, maximum MINI MCR power terminal block, with spring-cage connection, current consumption up to A, maximum ME 6, TBUS-,5/5-ST-, GN MINI MCR-SL-PTB 6 MINI MCR-SL-PTB-SP 67 Power supply unit, primary switched, slim design, output: V DC /.5 A MINI-SYS-PS-00-0AC/DC/ Power supply unit, primary switched, slim design, output: V DC /.5 A, ATEX approval MINI-PS-00-0AC/DC/.5/EX 6665 System adapter for MINI Analog modules MINI MCR-SL-V-FLK 6-A 6 Technical data Signal input Description of the input Current input signal Input resistance current input Transmitter supply voltage Current input (sensor circuit) ma... 0 ma (repeater power supply and isolator operation) 0 ma... 0 ma (isolator operation) Approx. 50 Ω 6.5 V Signal output Output description Non-load voltage Current output signal Max. current output signal Ripple Load/output load current output Power supply Nominal supply voltage Supply voltage range Power consumption General data HART function Limit frequency ( db) Measuring principle Transmission error, typical Transmission error, max. Temperature coefficient, typical Current output Approx..5 V ma... 0 ma (repeater power supply and isolator operation) 0 ma... 0 ma (isolator operation) > ma (.5 ma, typical) < 0 mv rms 500 Ω (at I = 0 ma) V DC 0. V DC... 0 V DC (to bridge the supply voltage, the DIN rail connector (ME 6, TBUS-,5/5-ST-, GN, Order No. 697) can be used. It can be snapped onto a 5 mm DIN rail according to EN 6075) < 900 mw (at V DC and in repeater power supply operation) < 600 mw (at V DC and in isolator operation) Yes > 5 Hz (typ.) Signal isolator 0. % (of end value) 0. % (of end value) < 0.00 %/K 00_en_00 PHOENIX CONTACT

3 General data (continued) Maximum temperature coefficient Step response (0-90%) Communication Mounting position Degree of protection Width Height Length Type of housing < %/K < ms (typ.) HART specification in both operating modes (RPSS isolator / RPSS repeater power supply) Any IP0 6. mm 9. mm 0.5 mm PBT green Connection data Screw connection Spring-cage connection Conductor cross section, solid 0. mm....5 mm 0. mm....5 mm Conductor cross section, stranded 0. mm....5 mm 0. mm....5 mm Stripping length mm mm Safe isolation Test voltage, input/output/supply.5 kv (50 Hz, min.) Ambient conditions Ambient temperature (operation) -0 C C Ambient temperature (storage/transport) -0 C... 5 C Conformance / approvals Conformance ATEX approval UL, USA / Canada GL CE compliant X II G Ex na II T X applied for UL applied for GL applied for Conformance with EMC directive 9/6/EEC Noise immunity according to EN Electrostatic discharge EN Criterion B Electromagnetic HF field EN Criterion A Fast transients (burst) EN Criterion B Surge current loads (surge) EN Criterion B Conducted interference EN Criterion A Noise emission according to EN Noise emission according to EN EN 550 Class A 00_en_00 PHOENIX CONTACT

4 Block diagram IN Power OUT I U DC DC DC 5 OUT I 6 GND 7 UB + GND ME 6, TBUS-... Safety notes WARNING: Correct usage in potentially explosive areas The module is a category item of electrical equipment. Follow the instructions provided here during installation. Install the module in housing with IP5 protection according to EN The specified limits for mechanical strain or thermal loads for the module must not be exceeded. Only modules suitable for operation in zone potentially explosive areas may be connected. Repairs must not be carried out by the user. In potentially explosive areas, snap the module onto the DIN rail and connect the cables only when the power is disconnected. CAUTION Installation, operation, and maintenance may only be carried out by qualified electricians. When installing and operating the device, the applicable safety directives (including national directives), accident prevention regulations, as well as general technical regulations, must be observed. CAUTION: Electrostatic discharge The module contains components that can be damaged or destroyed by electrostatic discharge. When handling the module, observe the necessary safety precautions against electrostatic discharge (ESD) according to EN and EN _en_00 PHOENIX CONTACT

5 Structure 6 5 CE Out I GND 9,...0 V DC GND MINI MCR-SL-RPSS-I-I Ord.-No.: Repeater Power Supply In / Out: 0()...0mA Load: 500W Transm. Error: < 0,% of full scale,5kv, 50Hz, min. 5 + OUT POWER - IN In I Test voltage: Amb.Temp.: C / F Power out GND GND Serial No. XXXXXXXX Input: Standard signals Output: Transmitter supply voltage Transparent cover Groove for ZBF 6 Zack marker strip 5 Output: Standard signals 6 Supply voltage 7 Connection option for DIN rail connector Universal snap-on foot for EN DIN rails 7 Power supply ATTENTION Never connect the supply voltage directly to the DIN rail connector. It is not permitted to draw power from the DIN rail connector or from individual MINI Analog modules. Supply via the MINI Analog Module Where the total current consumption of the aligned MINI Analog modules does not exceed 00 ma, the power can be supplied directly at the connection terminal blocks of one MINI Analog module. A 00 ma fuse should be connected. Supply via a Power Terminal Block The MINI MCR-SL-PTB power terminal block (Order No. 6) or the MINI MCR-SL-PTB-SP power terminal block (Order No. 67), which are the same shape, are used to supply the supply voltage to the DIN rail connector. A A fuse should be connected. Supply via the System Power Supply Unit The system power supply unit with.5 A output current connects the DIN rail connector to the supply voltage and can thus be used to supply several modules from the mains. MINI-SYS-PS-00-0AC/DC/.5 (Order No. 669) Potentially explosive areas: MINI-PS-00-0AC/DC/.5/EX (Order No. 6665) 00_en_00 PHOENIX CONTACT 5

6 Installation A B WARNING In potentially explosive areas, snap the module onto the DIN rail and connect the cables only when the power is disconnected. ATTENTION C D E Never connect the supply voltage directly to the DIN rail connector. It is not permitted to draw power from the DIN rail connector or from individual MINI Analog modules. The assignment of the connection terminal blocks is shown in the block diagram. The module can be snapped onto all 5 mm DIN rails according to EN When using T-BUS DIN rail connectors, first insert the DIN rail connector in the DIN rail to bridge the power supply (see assembly). Direction: Snap-on foot below and connector left. A B Screw connection (MINI MCR-...) Insert the wires in the corresponding connection terminal block. Use a screwdriver to tighten the screw in the opening above the connection terminal block. Serial No. XXXXXXXX 00_en_00 PHOENIX CONTACT 6

7 B A Spring-cage connection (MINI MCR-...-SP) Insert a screwdriver in the opening above the connection terminal block. Insert the wires in the corresponding connection terminal block. Serial No. XXXXXXXX HART Signal Transmission approx. +0,5mA With the HART protocol, a digital signal is modulated to the analog measurement signal. Data communication between the transmitter and the control device of the process control system can thus take place. Analog signal 0 approx. -0,5mA 00 Hz "" 00 Hz "0" 00_en_00 PHOENIX CONTACT 7

8 Connection examples...0ma IN I OUT I 5 IN I OUT I 5 Power OUT GND 6 U B Power OUT GND 6 UB + 7 Control system UB + 7 Control system GND GND MINI MCR-SL-RPSS-I-I V MINI MCR-SL-RPSS-I-I V Mains voltage Mains voltage Repeater power supply operation with a passive sensor Isolator operation with an active sensor Actuator IN I Power OUT OUT I GND 5 6 U B Control system UB + 7 GND MINI MCR-SL-RPSS-I-I V Isolator operation at the analog output module Mains voltage 00_en_00 PHOENIX CONTACT GmbH & Co. KG Blomberg Germany Phone: Fax: