Washroom Dispenser Service and Parts Manual Tork Elevation T2 Mini Twin Jumbo Roll Tissue Dispenser A, A Revision Date:

Transcription

1 Tork Elevation T2 Mini Twin JBT Dispenser: T2 System: A (white), A (black) Dispenser Dimensions HxWxD inches (cm): x 16.4 x 5.44 (27.08 x x cm) Tork T2 Mini Jumbo Bath Product Options: (Tork Advanced, 2 Ply) (Tork Advanced, 1 Ply) (Tork Advanced, 2-Ply) Dispenser Parts Part Description LEFT/RIGHT ROLL ARM SPINDLE PAPER ACCESS DOOR HOOD ASSY WHITE HOOD ASSY BLACK (Includes 2 e-clips & pins) KEY FOR ALL TORK DISPENSERS TORK LOCK KEYHANDLE FOR KEYLESS ENTRY Replacement SKU P (white) P (black) KEY or KEYHANDLE 1 of 5

2 Part Description with Replacement Instructions Parts with SKUs listed are available for order as of the revision date on the manual. Contact an SCA Sales Rep or the SCA Tissue Quality Coordinator to order these parts. If no SKU is listed, the availability of the part is unknown. Please contact the SCA Tissue Quality Coordinator for more information (see Contacting SCA section). Replacement SKU Description & Replacement Instructions P White P Black LEFT/RIGHT ROLL ARM The roll arms sit on the outside of the bath tissue rolls. As the roll is depleted, the roller gets close to the spindle, and allows the access door to unlock and slide to the opposite side for access to the reserve tissue roll. Not replaceable. SPINDLES Hold two jumbo bath tissue rolls. Not replaceable. PAPER ACCESS DOOR The access door will be locked to one side, allowing access to one of the tissue rolls and blocking access to the other until one roll has completely dispensed. Not replaceable. T2 MINI TWIN HOOD ASSEMBLY With door open, locate e-clip holding the hinge pin in place. Use pliers to remove the e-clip. Pull hinge pin out by pulling out to the left and the right side. Each hood assembly will include the hood, 2 new e-clips and 2 matching color hinge pins TORK LOCK The lock can be replaced by removing the U-clip from the inside of the dispenser with a pliers or screwdriver KEYHANDLE SCA KEYHANDLE Insert keyhandle into lock to provide keyless access. Note: Lock cannot revert bac keyed entry once keyhandle has been inserted KEY SCA METAL KEY FOR ALL TORK DISPENSERS Loading Instructions 1. To fill dispenser after mounting: Open cover. Before loading paper, slide door completely to one side. Raise the each roll arm, placing refill on spindle and resting arm on outside of full roll. Feed the paper through the opening and close the cover. For best performance, rolls should be oriented so each tail feeds over the top of the roll into the center of the dispenser. 2. When one of the rolls is completely dispensed, the access door will unlock and the user will be able to slide it to the opposite side. The user will then have access to the reserve tissue roll. 3. To replenish rolls: Open cover. Raise roll arm and remove the empty cores. Load a new Tork Jumbo Bath Tissue refill onto spindle Preventive Maintenance The dispenser should be cleaned any time there is heavy paper dust build-up inside the dispenser. If paper dust is not a problem, approximately every year is a good frequency for cleanings. The following is the recommended procedure to cleaning: 1) Open the dispenser and remove the rolls of paper. 2 of 5

3 2) Clean out any paper dust. This can be done is several ways, such as, vacuuming, blowing out with a can of compressed air (wear safety glasses), wiping out with a damp cloth, etc. 3) Clean the cover with a general all-purpose cleaner that is safe for plastics. Troubleshooting Problem: Any paper-related problem. Take note of the date code on the outside of the case of paper product. Then contact the SCA Tissue Quality Coordinator and explain the problem. Problem: Any other problem not stated above. Contact the SCA Tissue Quality Coordinator. Contacting SCA To contact the SCA Tissue Quality Coordinator, dial and press 6. Product Date Code Location: The product assembly code can be found on a white sticker placed on the inside of the dispenser door. The date code is in the following format: DD/MM/YYYY. This is a TorkSelect product. The TorkSelect label is affixed to the inside, right side of the dispenser. The system identifier (to match product refills) and the dispenser item number are printed on the bottom of this label. 3 of 5

4 555520A, A Tork ElevationT2 Mini Twin Dispenser Mounting Diagram Carton Instructions 4 of 5

5 Recommended Mounting Height (standard access) Mount dispenser 27.5 (70cm) above finished floor. Recommended Mounting Height (ADAAG Guideline) Dispensers. Toilet paper dispensers shall be installed within reach, as shown in Fig. 29(b). Dispensers that control delivery, or that do not permit continuous paper flow, shall not be used. Figure 29b Grab Bars at Water Closets Side Wall A 42 inch (1065 mm) minimum length grab bar is required to the side of the water closet spaced 12 inches (305 mm) maximum from the back wall and extending a minimum of 54 inches (1370 mm) from the back wall at a height between 33 and 36 inches ( mm). The toilet paper dispenser shall be mounted at a minimum height of 19 inches (485 mm). (4.16.3, , ) Note: Compliance with ADA guidelines is the responsibility of the installer and building owner. Local and state requirements may differ from ADAAG guidelines. 5 of 5