Output 1. Relay (n.o. make) 230V 3A. Response to probe break is configurable. JUMO di 32 / di 08 indicators

Transcription

1 JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, Fulda, Germany Postal address: Fulda, Germany Phone: Fax: Internet: JUMO Instrument Co. Ltd. JUMO House Temple Bank, Riverway Harlow, Essex CM20 2DY, UK Phone: Fax: Internet: JUMO Process Control, Inc. 8 Technology Boulevard Canastota, NY 13032, USA Phone: JUMO JUMO Fax: info@jumo.us Internet: Data Sheet Page 1/7 JUMO di 32 / di 08 Digital microprocessor indicators with 1 measurement input and a maximum of 3 signal outputs, case for flushpanel mounting to IEC Type /... Brief description The singlechannel digital indicators with the bezel sizes 48mm 24mm and 96mm 48mm are available for displaying measurements and monitoring limit values in industrial applications. The analog input permits the direct connection of thermocouples, RTD temperature probes, resistance transmitters, potentiometers or transducers with a standard signal. The sampling rate for the measurement input is 4 measurements per second. The indicators have a clearly legible 4digit LED display which, depending on the version, is 10mm (JUMO di 32) or 20mm (JUMO di 08) high, and serves to display the measurements, as well as being available for dialogs. Only three buttons are used for configuration. The parameter setting is arranged dynamically, and after two seconds without any operation the value is accepted automatically. The front protection is to IP66, at the rear IP20. The electrical connection is by plugin screw terminals. The possible input and output configurations are shown in the following block structure. Type /... Block structure Signal input Output 1 Thermocouples Type L, J, U, T, K, E, N, S, R, B, D, C RTD temperature probe Pt100, Pt1000, KTY116 Resistance transmitter, Potentiometer Current 0 20mA, 4 20mA Voltage 0 10V, 2 10V via floating contact on Type /... alternatively to output 2 on Type /... available as standard Supply 10 18V DC or 20 30V AC/DC 48 63Hz or V AC 48 63Hz JUMO di 32 / di 08 indicators (n.o. make) Response to probe break is Output 2 on Type /... Logic output 0/5V alternatively to logic input on Type /... (n.o. make) and parallel logic output 0/5V Response to probe break is Features k structured operating and programming layout k customerspecific linearization correction k 2 limit comparators for limit monitoring k digital input filter with programmable filter time constant k timedelayed switching, programmable per relay k switchon delay after poweron is programmable

2 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 2/7 Technical data Input for thermocouple Designation Range limits 1 Range Measurement accuracy in range FeCon L C FeCon J EN C CuCon U C CuCon T EN C NiCrNi K EN C NiCrCon E EN C NiCrSiNiSi N EN C Pt10RhPt S EN C Pt13RhPt R EN C Pt30RhPt6Rh B EN C W3ReW25Re D W5ReW26Re C C C Sampling rate Cold junction 1 The specifications refer to an ambient temperature of 20 C C C C C C C C C C C C C 4 measurements per second Pt100 internal or external constant (CJT) Ambient temperature error Input for RTD temperature probe Designation Connection circuit Range Measurement Ambient accuracy Pt100 EN wire C 0.1% 50 ppm/ C Pt100 EN wire C 0.1% 50 ppm/ C Pt1000 EN wire C 0.1% 50 ppm/ C Pt1000 EN wire C 0.1% 50 ppm/ C KTY116 2wire C 1.0% 50 ppm/ C Sensor lead resistance 20 max. per lead in 2wire and 3wire circuit Measuring current 250µA Lead compensation = factory setting not required for 3wire circuit. For 2wire circuit, lead compensation can be implemented in software through actualvalue correction. Input for resistance transmitter Designation Range Measurement accuracy Ambient 0 4k 0 4k 0.5% 50 ppm/ C Sensor lead resistance Measuring current Input for potentiometer 20 max. per lead 25µA or 250µA (depending on size of resistance) Designation Connection circuit Range Measurement accuracy Ambient 0 4k 2wire 0 4k 50 ppm/ C 0 4k 3wire 0 4k 50 ppm/ C Sensor lead resistance 20 max. per lead in 2wire and 3wire circuit Measuring current 250µA Lead compensation not required for 3wire circuit. For 2wire circuit, lead compensation can be implemented in software through actualvalue correction.

3 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 3/7 Input for standard signals Designation Range Measurement accuracy Voltage Current 0 10V, input resistance R E > 100k 2 10V, input resistance R E > 100k 4 20mA, voltage drop 3V 0 20mA, voltage drop 3V 0.1% 0.1% 0.15% 0.15% Ambient Measurement circuit monitoring 1 Transducer Overrange Underrange Probe or lead Probe or lead shortcircuit 1 break Thermocouple RTD temperature probe Resistance transmitter Potentiometer Voltage 2 10V 0 10V Current 4 20mA 0 20mA 1 In fault condition, the outputs move to a defined state (: active or inactive). recognized not recognized Assignment Type /... Type /... Number 1 (instead of the logic output only) 1 (standard) Function () Hold, Min/Max reset, level inhibit Operation through floating contact Outputs Assignment Type /... Type /... Output 1 relay relay Output 2 logic output or logic input relay and parallel logic output contact rating contact life Logic output current limiting load resistance Feature = factory setting make contact (n.o.) 3A at 230VAC resistive load 150,000 operations at rated load 0/5V 20mA R load 250 timedelayed switching of relays separately programmable per relay within the range sec Switchon delay Switchon delay after power ON Feature programmable within the range sec display and relays will only be activated after the programmed time has elapsed

4 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 4/7 Electrical data Supply (switchmode power supply) Case Case type plastic case for panel mounting to IEC (indoor use) Size in mm (for Type) Type /... Type /... Bezel 48 mm 24 mm 96 mm 48 mm Depth behind panel 100 mm 68.5 mm Panel cutout mm mm mm mm Ambient/storage temperature range 0 55 C / 40 to +70 C Climatic conditions 75% rel. humidity, no condensation Displays and controls 10 18V DC ±0% or 20 30V AC/DC 48 63Hz or V AC +10/15% 48 63Hz Test voltages (type test) to EN 61010, Part 1, March 1994, overvoltage category II, pollution degree 2, for Type /... overvoltage category III, pollution degree 2, for Type /... Power drawn 7VA max. Data backup EEPROM Electrical connection at the rear, via plugin screw terminals, conductor crosssection 1.5mm 2 (1.0mm 2 for Type /...) or 2 1.5mm 2 (1.0mm 2 for Type /...), with core end sleeves Electromagnetic compatibility (EMC) interference emission immunity to interference EN Class B to industrial requirements Safety regulation to EN Site altitude Operating position up to 2000 m above sea level Protection to EN 60529, front IP66, rear IP20 Weight 75g approx. 160g approx. any (1) Display 7segment display, 4 digits, red Height of digits Type /...: 10mm, Type /...: 20mm Display range/unit 1999 to digit / C/ F s none, one, two (2) Status indicators two LEDs for the outputs 1 and 2, yellow (3) Buttons q select next parameter, select parameter and configuration level (> 2sec) i, d increase 1, decrease 1 parameter value q + d q + i instant return to basic status display firmware version Example Type /... 1 Dynamic value setting; automatic acceptance of value after two seconds without pressing a button (also configuration codes)

5 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 5/7 Connection diagrams JUMO di 32, Type /... Output 2 Logic output 5V 20mA Output 1 Signal input N L1 Thermocouple Pt100/1000 (3wire) Pt100/1000 und KTY116 (2wire) floating contact (alternative to output 2) AC Mains supply V AC/DC 20 30V Potentiometer (3wire) DC = Potentiometer (2wire) 10 18V Resistance transmitter E S A Current 0/4 20mA Voltage 0/2 10V JUMO di 08, Type /... Output 3 Output 1 Output 2 Logic output 5V 20mA same function as output 2 Signal input Thermocouple Pt100/1000 (3wire) Pt100/1000 and KTY116 (2wire) floating contact N L1 AC Mains supply V AC/DC 20 30V Potentiometer (3wire) DC = Potentiometer (2wire) 10 18V Resistance transmitter E S A Current 0/4 20mA Voltage 0/2 10V

6 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 6/7 Dimensions Type / Type /... Sidebyside mounting (minimum spacing of panel cutouts) Type horizontal vertical /... > 8mm > 8mm /... > 10mm > 10mm

7 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 7/7 Order details: Digital microprocessor indicators with 1 measurement input and a maximum of 3 signal outputs, case for flushpanel mounting to IEC (1) Basic version / di 32 size 48mm 24mm / di 08 size 96mm 48mm (2) Input (programmable) x x 888 factoryset x x 999 configuration to customer specification 1 (3) Supply x x V DC ±0% x x V AC +10/15% 48 63Hz x x V AC/DC 48 63Hz (1) (2) (3) Order code / Order example / For configuration to customer specification, please specify the probe type and the required settings in plain text. Standard accessories 1 Operating Instructions B set of mounting brackets 1 seal