Braxton 7-pc Dining Set (Table) Model # BRA7PD-E

Transcription

1 LOT NUMBER: DATE PURCHASED: / / Braxton 7-pc Dining Set (Table) ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our toll-free customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday Or visit our website Or your request to parts@whalenfurniture.com THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Whalen Furniture Mfg., Inc. Page 1 Factory No

2 QUALITY GUARANTEE We are confident that you will be delighted with your Whalen Furniture purchase. Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture. This warranty gives you specific legal rights and you may also have other rights which vary from province to province (state to state). Customer Service: :30 a.m. - 4:30 p.m., PST, Monday to Friday MAXIMUM RECOMMENDED WEIGHT LOADS 1. Maximum load weight kg (400 pounds). THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. GENERAL INFORMATION, TIPS & TRICKS 1. Please read the Assembly Instructions prior to assembling the unit. 2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface. 3. Keep all hardware and parts out of the reach of children. 4. Please wait until all steps are completed before fully tightening bolts. 5. Make sure all bolts and screws are tightly fastened before the unit is used. 6. Check that all bolts, screws and knobs are tight at least every 3 months or as needed. Whalen Furniture Mfg., Inc. Page 2 Factory No

3 Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Table Top (1) B- Inner Leg (2) C- Outer Leg (2) D- Stretcher (1) E- Mounting Board (2) (1) 1/4 x 3/4 Bolt (2) 5/16 x 2 Bolt (3) 5/16 x 3 Bolt (4+1 extra) (16+1 extra) (4+1 extra) (4) Large Lock Washer (5) Large Flat Washer (6) Small Lock Washer (7) Small Flat Washer (20+1 extra) (20+1 extra) (4+1 extra) (4+1 extra) (8) Metal Bracket (2) M4 Allen wrench (1) M5 Allen wrench (1) Tools required: Allen wrench (provided). Whalen Furniture Mfg., Inc. Page 3 Factory No

4 Assembly Instructions DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts. 1. Unpack the unit and confirm that you have all the hardware and required parts. 2. Attach the Stretcher (D) between 2 Inner Legs (B) by inserting the 3 Bolts (3) through the Large Lock Washers (4) and Large Flat Washers (5) through the countersunk holes on the cutout of the Legs and screw into the Stretcher, as shown in the illustration below. Tighten the bolts with the provided Allen wrench. B D 3 Bolt (4 used in this step) 3 Large Lock Washer (4 used in this step) 4 Large Flat Washer (4 used in this step) 5 Whalen Furniture Mfg., Inc. Page 4 Factory No

5 Assembly Instructions 3. Attach the Outer Legs (C) to the Inner Legs (B) by snugly fitting the cutouts together. Make sure that the threaded inserts for the Mounting Bards (E) point towards the same direction. B C Whalen Furniture Mfg., Inc. Page 5 Factory No

6 Assembly Instructions 4. Align and attach one Mounting Board (E) to the top of the Legs (B and C) by using four 2 Bolts (2) and four Large Washers (4 and 5). Tighten the bolts with the provided 5 mm Allen wrench. 5. Repeat last step with the other Mounting Board (E). E 5 E E B/C 2 Bolt (8 used in this step) 2 Large Lock Washer (8 used in this step) 4 Large Flat Washer (8 used in this step) 5 Whalen Furniture Mfg., Inc. Page 6 Factory No

7 Assembly Instructions 6. Position the Table Top (A) upside down on a level and protective surface, as shown below. 7. Ask for assistance to flip the assembled base upside down and align the pre-drilled holes on the Mounting Boards (E) with the threaded inserts on the slides supports of the Table Top (A). Securely screw eight 2 Bolts (2) with the Large Washers (4 and 5) through the pre-drilled holes on the Mounting Boards (E) and then into the slides supports, using the provided 5 mm Allen wrench. E E A 2 Bolt (8 used in this step) 2 Large Lock Washer (8 used in this step) 4 Large Flat Washer (8 used in this step) 5 Whalen Furniture Mfg., Inc. Page 7 Factory No

8 Assembly Instructions 8. To secure the legs in place, align and attach the Metal Brackets (8) to the joint of the Inner Leg (B) and Outer Leg (C) using the 3/4" Bolts (1) with the Small Lock Washers (6) and the Small Flat Washers (7), two bolts per Metal Bracket. Tighten the bolts with 4 mm Allen wrench. C B C A 3/4 Bolt (4 used in this step) 1 Small Lock Washer (4 used in this step) 6 Small Flat Washer (4 used in this step) 7 Metal Bracket (2 used in this step) 8 Whalen Furniture Mfg., Inc. Page 8 Factory No

9 Assembly Instructions 9. Ask for assistance to lift the unit upright and position it at the desired location. 10. Unlock the sash locks underneath the Table Top (A) and release the slide locks on both slide mechanisms to allow the slide to operate, then pull the Table Top wide open equally from both ends. 11. Lift the Butterfly Leaf from the compartment of the Table Top (A) and flip up the Leaf. Unfold the leaf aprons and rest the leaf onto the top surface carefully. 12. Push the Table Top (A) from both ends to close and lock the sash locks underneath the Table Top and flip down the black toggle on each slide mechanism to lock the slides in place. ON OFF Whalen Furniture Mfg., Inc. Page 9 Factory No

10 ON OFF To Store the Butterfly Leaf When Not In Use 13. Unlock the sash locks underneath the Table Top (A) and release the slide locks on both slide mechanisms to allow the slide to operate, then pull the Table Top wide open equally from both ends. 14. Flip down the leaf aprons and fold the butterfly leaf to store within the compartment, as shown. 15. Push the Table Top (A) from both ends to close and lock the sash locks underneath the Table Top and flip down the black toggle on each slide mechanism to lock the slides in place. Whalen Furniture Mfg., Inc. Page 10 Factory No

11 Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing. Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish. Stains or marks from crayons or ink markers will be difficult to remove. In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture. Check bolts/screws periodically and tighten them if necessary. Further advice about wood furniture care It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish. Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages. A touch-up pen has been provided to repair any small nicks or scratches that may occur during assembly or shipping. We hope you enjoy your purchase for many years. Thank you for choosing Whalen Furniture! Whalen Furniture Mfg., Inc. Page 11 Factory No

12 IF YOU NEED TO ORDER ANY REPLACEMENT PARTS, PLEASE USE THE LIST BELOW Braxton 7-pc Dining Set (BRA7PD-E) *BRA7PD-E-1-CB Chair Backrest *BRA7PD-E-18-TS Table Stretcher *BRA7PD-E-2-SF Seat Frame *BRA7PD-E-19-MB Mounting Board *BRA7PD-E-3-SC Seat Cushion *BRA7PD-E-20-HN Hex Nut *BRA7PD-E-3A-SCS Seat Cushion Screw *BRA7PD-E-21-MB Metal Bracket *BRA7PD-E-4-LSS Left Side Stretcher *BRA7PD-E-22-LLW Large Lock Washer *BRA7PD-E-5-RSS Right Side Stretcher *BRA7PD-E-23-LFW Large Flat Washer *BRA7PD-E-6-LFL Left Front Leg *BRA7PD-E-24-SLW Small Lock Washer *BRA7PD-E-7-RFL Right Front Leg *BRA7PD-E-25-SFW Small Flat Washer *BRA7PD-E-CHC Complete Hardware for Chair *BRA7PD-E-26-3/4B 1/4" x 3/4" Bolt *BRA7PD-E-8-TTWS Table Top w/slides *BRA7PD-E /4B 5/16" x 1-3/4" Bolt *BRA7PD-E-8A-MSM Metal Slide Mechanism *BRA7PD-E-28-2B 5/16" x 2 Bolt *BRA7PD-E-9-IL Inner Leg *BRA7PD-E-29-3B 5/16" x 3" Bolt *BRA7PD-E-10-OL Outer Leg *BRA7PD-E /2B 5/16" x 3-1/2" Bolt *BRA7PD-E-11-BL Butterfly Leaf *BRA7PD-E-31-2WS 2" Wood Screw *BRA7PD-E-12-LHS Leaf Hinge w/screws *BRA7PD-E-32-M4AW M4 Allen Wrench *BRA7PD-E-13-LA Leaf Apron *BRA7PD-E-33-M5AW M5 Allen Wrench *BRA7PD-E-14-LAHS Leaf Apron Hinge w/screws *BRA7PD-E-34-OW Open Wrench *BRA7PD-E-15-BGC Ball-style Grab Catches *BRA7PD-E-35-TUP Touch-up Pen *BRA7PD-E-16-LHS Leaf Holder w/screws *BRA7PD-E-CHT Complete Hardware for Table *BRA7PD-E-17-SL Sash Lock