Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement"

Transcription

1 Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations for the Northstar JRC series 2kW Radar domes. This instruction may also be used as a guide for the replacement of damaged or defective cables. Standard Inventory Configurations P/N NS004790R - supplied with a 15 Meter Scanner Cable P/N NS pre-installed from the factory. P/N NS004790M - supplied with a pigtail cable P/N NS only. The appropriate cable OEM extension cables configuration can be added depending upon installation requirements. P/N NS "Bare" dome with no pigtail or cabling supplied. Section 1 - Removing a new unit from the packaging With the radar carton facing upright, use a razor knife to carefully open the box along the tape seams on top centerline and ends of the container. Follow the seam lines exactly and DO NOT CUT TOO DEEPLY to avoid damage to the enclosed templates and packing materials. Remove the top cardboard layer. This has the template and installation guide attached to it. Save this for re-use when repackaging the unit. Remove the formed foam packing that surrounds the top of the radar dome. Save this for re-use when repackaging the unit. Inspect the carton to make sure that the bolt package and rubber mounts are included. DO NOT REMOVE THESE PARTS FROM THE CARTON unless the radar is immediately going to be installed on a vessel. Leave these parts in the carton so that they won't be misplaced or forgotten when the unit is re-packaged. Bolt and rubber mount packages Remove the cardboard end packing that retains the radar scanner cable in place if it's installed. When unpacking a unit not having a factory installed scanner cable this will be at the aft end of the unit (the end with the cable gland nut). Note the orientation of the cardboard packing spacer that retains the cable. Save this spacer for re-use when re-packaging the unit. Move the radar and cable assembly to a work station with a padded work surface to begin the disassembly process.

2 Section 2 - Disassembling the radar to Replace or Reconfigure the scanner cable. Turn the dome top side down on a soft protected work surface and carefully remove the protective plastic bag enclosing the radar dome. Save this for re-use when repackaging the unit. Fully loosen the 4 cover retaining screws using a straight slot screwdriver or 5/16" nutdriver. The screws are captive to the assembly, they should not be removed from the bottom assembly. Grasp the sides of the dome so that the top and bottom halves stay together and flip the dome over so that the dome cover can then be removed. Bottom View of 2kW Dome showing cover screw locations

3 Remove the six screws that secure the transmitter and antenna assembly to the dome base. There are two #2 Phillips screws and four #1 Phillips screws. Top View with Dome cover removed showing the locations for the screws that secure the transmitter and antenna assembly

4 Interior view of cable gland nut assembly. Note location of black tape on the cable, the cable is not pulled tight nor is the black tape inside of the gland nut area. Loosen the gland nut and slide the rubber packing out of the gland housing. View of gland nut and packing partially disassembled

5 Disassemble the packing assembly by sliding the "plastic finger grip" back onto the cable toward the gland nut so that the two rubber wraps can be disassembled and removed from the cable. At this point the cable can be easily moved in or out of the dome housing as required for completing the disassembly. Refer to the two preceding and the following pictures for additional clarity. Individual gland nut components when completely removed from the scanner cable Once removed place the two rubber seal halves aside, they will be needed in the reassembly process.

6 Lift up the transmitter and antenna assembly and temporarily position the assembly in the "holding clips" built into the forward bottom portion of the radar transmitter mounting base assembly. Transmitter assembly supported by the "holding" clips built into the mounting base Position and routing of the scanner cable along with the orientation of the cable clamp used to secure the scanner cable to the transmitter assembly

7 Work the cable back through the cable gland to obtain extra slack in the cable. If possible reposition the transmitter and antenna assembly into a padded jig allowing the assembly to be positioned with the shield and transmitter face up. This will allow ease of access to the shield and cabling components. Make sure that the antenna and the plastic gearing will not be damaged by contact with any portion of the jig. If a jig is not available, position the assembly in the holding clips located in the base assembly. Work carefully to avoid any damage to the transmitter and antenna components. View of the transmitter shield cover showing the locations of the shield screws. Remove the transmitter shield screws, black in color, eight each, using a #1 Phillips screwdriver. Caution - do not remove the two screws securing the power transistors that are heatsinked to the aluminum baseplate assembly. These are located next to the shield screws at the end of the shield that is opposite where the scanner cable enters the shield. Once the shield cover is removed, remove the screw that secures the scanner cable clamp and the grounding strap to the transmitter housing. The scanner cable is stiff and will attempt to "spring back". Do not allow the cable to apply tension or stress to the data wires, connectors or the PCB assembly. Firmly hold the cable when the clamp is removed and use slack in the cable to reposition the cable and remove the tension.

8 View showing the cable clamp screw and shield grounding connection with the transmitter shield removed Disconnect the seven pin data connector by carefully grasping the connector body and pulling straight up. The connector is a snap fit without a locking device. Do not rock the connector from side to side when removing it to avoid bending pins or pulling individual wires loose. Disconnect the three pin power connector by depressing the locking tab and pulling straight up on the connector. Picture showing both connectors removed. The three pin connector has a latch; the seven pin connector is a press and snap fit.

9 Once disconnected the scanner cable can be removed from the lower half of the dome. Carefully thread the connector bodies and shield strap back through the cable gland housing. Due to the amount of clearance in the gland housing this will normally need to be done one connector at a time. Remove the "plastic finger grip" and the gland nut from the cable. Place these with the two rubber seals removed earlier. All of these parts will be re-installed when a new cable is installed. Helpful tips - To save time and to prevent difficulties during assembly, pay close attention to the following areas 1.Place the cable gland nut and "plastic finger grip" on the new cable before you start assembly. 2. Verify that the power and data connectors are correctly and firmly seated both by feel and with a visual inspection. 3. Verify that none of wires are pinched or can be chafed by edges of the shield or any internal metal parts. Cable and wire routings are very specific, DO NOT make changes. 4. Verify correct orientation of the cable clamp. The shield will not seat correctly if the clamp is orientated incorrectly. 5. Verify that the connection of the bonding strap and that it is correctly installed beneith the scanner cable clamp. 6. Verify that the transmitter shield is correctly placed and fitted. There are two metal guides located on the transmitter base plate. When properly placed, the shield goes over and to the outside of the guides. If the shield mounting holes don't line up this is the common cause. 7. Verify correct routing of the scanner cable in the dome bottom during final assembly.

10 Reassembly Possible scanner cable length configurations. If assembling a BBG 1.125M pigtail cable configuration, use Northstar P/N NS If assembling an Aftermarket 15M cable configuration, use Northstar P/N NS If assembling an Aftermarket 20M cable configuration, use Northstar P/N NS Install the gland nut and "plastic finger" grip on the new scanner cable to be installed. The gland nut is installed on the cable first with the threaded portion facing toward the scanner end of the cable followed by the "plastic finger grip". These must be installed onto cable before routing through the gland housing and into the radar dome bottom. The rubber seal halves are not installed at this time but will be installed during the final assembly. Route enough cable through the cable gland to allow some slack for orientating the cable. Using the preceding pictures in the disassembly instructions as a guide, route the scanner cable into position so that the connectors can be inserted into there respective locations on the transmitter board without undue twisting or straining of the wires or PCB connections. If necessary, firmly grip the cable and bend it as required to properly position the wires. The "proper" bend will allow the correct positioning of the cable clamp to restrain the scanner cable without putting undue strain on the connections. Loosely assemble the scanner cable clamp and clamp screw allowing enough space under the clamp to insert the spade terminal attached to the shield ground. Position the cable and align it so that it will exit the transmitter board as shown in the preceding pictures. Correctly position and hold the shield ground and scanner cable while tightening the clamp screw. DO NOT OVER TIGHTEN. The clamp screw threads into the aluminum sheet metal base and it's threads can be stripped if over-tightened. The cable will exit at 90 degrees to the long axis of the transmitter board when correctly positioned. Install the transmitter shield cover making sure none of it's edges are touching the scanner cable or the wire bundle for the servo motor. Fit the covers touches the motor wires refit them so that they are pushed into the slot between the motor housing and the PCB is that the shield can not come in contact with them. Secure all eight shield cover screws. Inspect all hardware and wires for security and proper placement. Lift up the transmitter and antenna (T/A) assembly and adjust the scanner cable until the assembly can be lower down onto it's normal mounting location. Loosely install the six screws that secure the T/A assembly to the bottom mounting plate. Verify the correct positioning of the scanner cable and then tighten down the six T/A mounting screws Adjust the scanner cable so that it does not rub or chafe on any of the interior parts.

11 Assemble the packing assembly using the preceding pictures as a guide. Note that the large portion of the taper on the smaller inner seal is orientated away from the radar while the large portion of the taper larger outter seal is toward the radar cable gland housing. Align the seals so that the splits are 180 degrees apart. Work the "plastic finger grip" up over the end of the seal assembly that is away from the gland housing. (The "small" end) Line the seal up inside the gland housing and carefully thread the gland nut on using care not to cross the threads. Once the threads are correctly started, tighten up the assembly hand tight. DO NOT USE PLIERS or gripping tools on the plastic gland nut to avoid damage. When properly assembled this assembly only requires tightening by hand in order to be waterproof.

EasyNote TJ Series. Disassembly Manual

EasyNote TJ Series. Disassembly Manual EasyNote TJ Series Disassembly Manual CHAPTER3 Replacing notebook components Preventing static electricity discharge Preparing the work space Required tools Preparing the notebook Adding or replacing memory

More information

Trillium 40 Axis Spring Tensioner Wire Replacement Instructions

Trillium 40 Axis Spring Tensioner Wire Replacement Instructions Trillium 40 Axis Spring Tensioner Wire Replacement Instructions 1 Overview The objective is to replace the broken axis spring tensioner wire. This requires the following tasks: 1. Remove the seismometer

More information

Dell P Series Monitor VESA Mounting Bracket Installation Instructions

Dell P Series Monitor VESA Mounting Bracket Installation Instructions Dell P Series Monitor VESA Mounting Bracket Installation Instructions The VESA mounting bracket enables a Wyse cloud client to be mounted to the Dell P Series Monitor and the Dell E24 Monitor. The cloud

More information

TOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation

TOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43

More information

GATEWAY NOTEBOOK SERVICEGUIDE

GATEWAY NOTEBOOK SERVICEGUIDE GATEWAY NOTEBOOK SERVICEGUIDE Contents Replacing Notebook Components................................... 1 Identifying the notebook model........................................ 2 Identifying components..............................................

More information

Elecraft K3 Audio Output Chip Protection Modification Installation Instructions

Elecraft K3 Audio Output Chip Protection Modification Installation Instructions Introduction Elecraft K3 Audio Output Chip Protection Modification Installation Instructions Revision B, June 6, 2013 Copyright 2013, Elecraft, Inc. All Rights Reserved Even though the K3 s audio output

More information

INSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AD Last Updated: 12/03/13 US PATENT: D683,281 CHINESE PATENT: ZL

INSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AD Last Updated: 12/03/13 US PATENT: D683,281 CHINESE PATENT: ZL PREMIUM FRONT BUMPER AEV30103AD Last Updated: 12/03/13 US PATENT: D683,281 CHINESE PATENT: ZL 2012 3 0026032.0 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND

More information

Telescope Service. Meade LX200 Classic Telescopes. Procedures for Removal and Installation of Printed Circuit Board And Motor Assemblies

Telescope Service. Meade LX200 Classic Telescopes. Procedures for Removal and Installation of Printed Circuit Board And Motor Assemblies Telescope Service Meade LX200 Classic Telescopes Procedures for Removal and Installation of Printed Circuit Board And Motor Assemblies STATIC ELECTRICITY HAZARD AND PREVENTION Static electricity can easily

More information

Rack Installation Instructions

Rack Installation Instructions Rack Installation Instructions Second Edition (June 2014) 2014 Contents Chapter 1. Safety information..... 1 Chapter 2. Rack kit parts inentory... 3 Chapter 3. Rack installation...... 5 Identifying the

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service

More information

Triac Printed Circuit Board Replacement

Triac Printed Circuit Board Replacement Technical Service Bulletin: Triac Printed Circuit Board Replacement TRONIC 5000C Pro Models: WH17, WH27, WH36 Introduction Fig. 1 ELECTRICITY IS EXTREMELY DANGEROUS. TAKE EXTRA PRECAUTIONS AND ENSURE ALL

More information

Service Guide. Gateway M275

Service Guide. Gateway M275 Service Guide Gateway M275 Contents Replacing Gateway M275 Components.................................... 1 Identifying the convertible tablet PC model...................................... 2 Identifying

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,

More information

http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html

http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html TECHNICAL SERVICE DEPARTMENT Removal, Cleaning, & Reinstallation of the Burner Assembly For models 74 & GT199 Required tools -

More information

5800 Temperature Sensor Cable Assembly

5800 Temperature Sensor Cable Assembly 5800 Temperature Sensor Cable Assembly Removal and Replacement Instruction Sheet #60-4702-070 Revision D, January 14, 2013 Overview The 5800 has two refrigeration temperature sensors, one attached to the

More information

Installation Instructions Complete Top Frame & Hardware With Soft Upper Doors Jeep Wrangler

Installation Instructions Complete Top Frame & Hardware With Soft Upper Doors Jeep Wrangler Installation Instructions Complete Top Frame & Hardware With Soft Upper Doors 87-95 Jeep Wrangler IMPORTANT NOTICE: Carefully read instructions before attempting to install this product. Rampage Products

More information

Juice Box Stages 1&2 135&335 Installation Guide 5/10/08

Juice Box Stages 1&2 135&335 Installation Guide 5/10/08 Tools Required: 8mm socket or nut driver Small flat head screwdriver Electrical tape, masking tape, or shrink tube Pep talk: Although the install looks daunting at first, once you get the learning curve

More information

MGB Chrome Bumper Conversion

MGB Chrome Bumper Conversion MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different

More information

Express5800/120Ed. Rack Mount Kit Installation Procedures PN: 455-01607-001

Express5800/120Ed. Rack Mount Kit Installation Procedures PN: 455-01607-001 Express5800/120Ed Rack Mount Kit Installation Procedures PN: 455-01607-001 Proprietary Notice and Liability Disclaimer The information disclosed in this document, including all designs and related materials,

More information

Elecraft K3 KPA3 Power Connector Replacement Revision A Review, April 16, 2012 Copyright 2012, Elecraft, Inc. All Rights Reserved

Elecraft K3 KPA3 Power Connector Replacement Revision A Review, April 16, 2012 Copyright 2012, Elecraft, Inc. All Rights Reserved Introduction Elecraft K3 KPA3 Power Connector Replacement Revision A Review, April 16, 2012 Copyright 2012, Elecraft, Inc. All Rights Reserved The connectors furnishing high current to the KPA3 module

More information

POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS

POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS Polemount Field Fix Support If you have any questions or incur any problems installing or using the new Polemount, please use Miovision s Support System by emailing

More information

Installing Your 960 or 980 Server into a Rackmount Cabinet

Installing Your 960 or 980 Server into a Rackmount Cabinet Installing Your 960 or 980 Server into a Rackmount Cabinet 1 2 Contents Installing Your Gateway Server into a Rackmount Cabinet...1 Identifyingpartsintheaccessorykit...2 Rackmounthandlekit... 2 Rackmountrailkit...

More information

CP2 Buried Cable Pedestal Initial & Rehab Installation Instructions

CP2 Buried Cable Pedestal Initial & Rehab Installation Instructions Printing 3 March 2008 CP2 Buried Cable Pedestal Initial & Rehab Installation Instructions This instruction is intended for CP2 cable pedestal installations and replacements. The following tools will be

More information

TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation

TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation Part Number: PT297-35061 Kit Contents Item # Quantity Reqd. Description 1 2 Driving Lamp Assembly 2 1 Switch Harness 3 1 Lamp Harness 4 2 Stone Shield

More information

UNPACKING AND ASSEMBLY

UNPACKING AND ASSEMBLY UNPACKING AND ASSEMBLY Assembly Instructions Step 1. Open the two boxes and remove all the parts. Lay out the parts as shown below and read through the assembly instructions before beginning assembly.

More information

Rollator Cane and Brake Replacement SAFETY SUMMARY (CONTINUED)

Rollator Cane and Brake Replacement SAFETY SUMMARY (CONTINUED) Rollator Cane and Replacement Assembly, Installation and Operating Instructions SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use. Contact Carrier/Dealer

More information

Fresenius Medical Care North America Service Bulletin

Fresenius Medical Care North America Service Bulletin Fresenius Medical Care North America Service Bulletin Equipment: Bulletin: Subject: 2008 K Hemodialysis Machines 15-FRK-001 Rev A Optional Shunt Box Ferrite Core Installation (Update) 1.0 PURPOSE To inform

More information

Polaris Slingshot Trailer Hitch Installation Instructions #PSS007

Polaris Slingshot Trailer Hitch Installation Instructions #PSS007 Polaris Slingshot Trailer Hitch Installation Instructions #PSS007 1. Lay out and familiarize yourself with the components and hardware supplied with the hitch. Note the included trailer wiring isolator

More information

apple Service Source PowerBook G4 (DVI) Updated 4 December 2003 2003 Apple Computer, Inc. All rights reserved.

apple Service Source PowerBook G4 (DVI) Updated 4 December 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source PowerBook G4 (DVI) Updated 4 December 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Upgrades PowerBook G4 (DVI) 2003 Apple Computer, Inc. All rights reserved.

More information

Accessing the printer system board

Accessing the printer system board Accessing the printer system board 1 Turn the printer off. 2 Unplug the printer power cord. 3 Disconnect all cables from the back of the printer. 4 Locate the metal plate at the back of the printer. Loosen

More information

PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129

PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: The information included in this Splendide Repair Manual may change without notice. Please see our web site www.splendide.com/service/docs.html for updates,

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic

More information

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE

More information

Document number RS-PRD-00130 Revision 05 Date 20/10/2009 Page 1/30

Document number RS-PRD-00130 Revision 05 Date 20/10/2009 Page 1/30 Date 20/10/2009 Page 1/30 1. Purpose This document describes the field replacement of the footscan plate cable for these models: 2m hi-end plate SN 11/5/xxx 2m pro plate SN 7/5/xxx 0.5m 2003 hi-end plate

More information

Removing memory and option cards

Removing memory and option cards These instructions can help you remove memory or option cards. Use the following illustration to locate the connector for the card you want to remove. Hard disk connector 1 Option card connector Firmware

More information

Solstice/Sky Water Pump Replacement

Solstice/Sky Water Pump Replacement Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the

More information

2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure

2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure 2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure Derek Guenther 1/28/2015 Rev. Purpose The purpose of this document is to describe the procedure necessary to replace one of the ball nuts

More information

Traditional Sonar and DSI Sonar Installation

Traditional Sonar and DSI Sonar Installation Traditional Sonar and DSI Sonar Installation This document covers the installation of the transducer and display unit installation, which includes connecting the unit to power and installing the unit on

More information

TraceTek TTDM Series Leak Detection and Location Modules Replacement Parts Installation Instructions

TraceTek TTDM Series Leak Detection and Location Modules Replacement Parts Installation Instructions TraceTek TTDM Series Leak Detection and Location Modules Replacement Parts Installation Instructions TRACETEK TraceTek TTDM Replacement Parts General Information These instructions detail the steps to

More information

SERVICE GUIDE. Gateway Notebook

SERVICE GUIDE. Gateway Notebook SERVICE GUIDE Gateway Notebook Contents Replacing Gateway Notebook Components...................................1 Identifying the notebook model......................................... 2 Identifying

More information

Upgrade Kit Instructions

Upgrade Kit Instructions Upgrade Kit Instructions Thank you for purchasing an IRIS+ Upgrade Kit. You re now ready to transform your IRIS into an IRIS+. You will need: -Phillips-head screwdriver -2 mm hex key -Glue for foam, preferably

More information

ATS Overhead Table Shelf System INSTRUCTION MANUAL

ATS Overhead Table Shelf System INSTRUCTION MANUAL ATS Overhead Table Shelf System INSTRUCTION MANUAL ATS Overhead Table Shelf System Instruction Manual Warranty Newport Corporation warrants this product to be free of defects in material and workmanship

More information

Overview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer

Overview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer Overview READ ENTIRE INSTRUCTIONS BEFORE STARTING INSTALLATION PARTS LIST A. Flush valve B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve

More information

HP Laser Jet 4200/4240/4250/4300/4350 Swing Plate

HP Laser Jet 4200/4240/4250/4300/4350 Swing Plate HP Laser Jet 4200/4240/4250/4300/4350 Swing Plate 1 Swing Plate Assembly-RM1-0043 1 Swing Plate Kit-5851-2766 (RM1-0043 plus RM1-1091 gear) CAUTION: Fuser may be hot. Turn off printer, unplug it and allow

More information

CONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation

CONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER

More information

jbs nfb INSTALLATION INSTRUCTIONS AND OWNERS MANUAL Mechanical Steering for Inboard, Outboard, and Sterndrive Powered Vessels

jbs nfb INSTALLATION INSTRUCTIONS AND OWNERS MANUAL Mechanical Steering for Inboard, Outboard, and Sterndrive Powered Vessels MEMBER INSTALLATION INSTRUCTIONS AND OWNERS MANUAL Part # IS-SH5094, Rev 3, 04/204 www.seastarsolutions.com SH5294 DUAL SH5094 SINGLE jbs nfb Mechanical Steering for Inboard, Outboard, and Sterndrive Powered

More information

Inspiron 15. Service Manual. 3000 Series

Inspiron 15. Service Manual. 3000 Series Inspiron 15 3000 Series Service Manual Computer Model: Inspiron 15 3541/Inspiron 15 3542/Inspiron 15 3543 Regulatory Model: P40F Regulatory Type: P40F001/P40F002 Notes, Cautions, and Warnings NOTE: A NOTE

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (748-547) Chrysler 300 2005 10, Dodge Magnum 2005 08, Dodge Charger 2006 09 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not

More information

Socket A AMD Processor Installation Guide

Socket A AMD Processor Installation Guide 23986 December 2000 Socket A AMD Processor Installation Guide Socket A AMD Processor Installation Guide Thank you for purchasing a Socket A AMD processor. Before installing the new AMD processor in a system,

More information

PULL CHAIN SPEED CONTROL REVERSE SWITCH XTR MOTOR

PULL CHAIN SPEED CONTROL REVERSE SWITCH XTR MOTOR PULL CHAIN SPEED CONTROL REVERSE SWITCH The Casablanca 4-Speed series of fans feature a 4-speed, pull chain fan control and a forward/reverse slide switch. XTR MOTOR PRINTED CIRCUIT BOARD LIGHT KIT PULL

More information

Replacement Instructions. Warning: During this procedure, keep small parts away from children.

Replacement Instructions. Warning: During this procedure, keep small parts away from children. apple ibook G4 Memory Card Replacement Instructions Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note: Written

More information

Figure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top.

Figure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top. Here are some pictures to show what s required when replacing the A/C compressor, expansion valve and receiver/drier on a 2001 Volvo V70. Even if you don t replace these A/C parts these pictures can help

More information

1. SAFETY RULES WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT".

1. SAFETY RULES WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT. 1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National

More information

CEILING FAN OWNER'S MANUAL

CEILING FAN OWNER'S MANUAL CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODEL: 52P-646-5RV-187 52P-646-5RV-323 FAN RATING AC 120V. 60Hz CUL LISTED MODEL : AC-552A 1. TOOLS AND MATERIALS REQUIRED Philips screw driver

More information

Mazda MX-5 Soft Top Installation Instructions

Mazda MX-5 Soft Top Installation Instructions Mazda MX-5 Soft Top Installation Instructions These instructions show how to replace your soft top with the frame remaining attached to the car. This requires the use of a right angled driver which is

More information

ATA Hard Drive. Replacement Instructions. K Power Mac G4 Cube. Tools Required. Electrostatic Discharge (ESD) Backing Up Your Data

ATA Hard Drive. Replacement Instructions. K Power Mac G4 Cube. Tools Required. Electrostatic Discharge (ESD) Backing Up Your Data K Power Mac G4 Cube ATA Hard Drive Replacement Instructions Be sure to follow these instructions carefully. Failure to follow these instructions could result in damage to your equipment and may void your

More information

430 Power/Electronics Replacement

430 Power/Electronics Replacement Replacing the main board WARNING Before proceeding, turn off the main power switch and unplug the power cord. Caution Make sure you are properly grounded with an ESD strap before continuing. The main printed

More information

Teledyne Isco Syringe Pumps: Care and Maintenance

Teledyne Isco Syringe Pumps: Care and Maintenance Teledyne Isco Syringe Pumps: Care and Maintenance ~ Overview ~ This bulletin provides instructions for performing normal periodic maintenance required by Teledyne Isco syringe pumps, followed by servicing

More information

OWNER S MANUAL. Ceiling Fan Installation Instructions QUALITY CEILING FANS. For 5SLR52 Series Fans. Total fan weight with light

OWNER S MANUAL. Ceiling Fan Installation Instructions QUALITY CEILING FANS. For 5SLR52 Series Fans. Total fan weight with light OWNER S MANUAL Ceiling Fan Installation Instructions Total fan weight with light For 5SLR52 Series Fans READ AND SAVE THESE INSTRUCTIONS QUALITY CEILING FANS Installation SAFETY TIPS WARNING: TO REDUCE

More information

OWNER S MANUAL Table Tennis Table Patent Pending

OWNER S MANUAL Table Tennis Table Patent Pending OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179

More information

INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5100 for use with R1100RT and R1150RT

INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5100 for use with R1100RT and R1150RT INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5100 for use with R1100RT and R1150RT Read these instructions carefully and thoroughly before beginning work. Before installing the accessory,

More information

Installation Instructions 4508 4508S

Installation Instructions 4508 4508S SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect

More information

Mini Cooper and S Trailer Receiver Hitch Installation Instructions

Mini Cooper and S Trailer Receiver Hitch Installation Instructions Application Mini Cooper and S 3 Door Hatch or Convertible; M1001-02-06 Mini Cooper M1002-02-06 Mini Cooper S Hitch Capacity 1400 lbs gross, 200 lb max tongue Notes: This hitch features a removable ball

More information

Dell E Series Monitor VESA Mounting Bracket Installation Instructions

Dell E Series Monitor VESA Mounting Bracket Installation Instructions Dell E Series Monitor VESA Mounting Bracket Installation Instructions The VESA mounting bracket enables a Wyse cloud client to be mounted to the Dell E Series Monitor. The bracket attaches to the monitor

More information

VERTICAL BLINDS GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE

VERTICAL BLINDS GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE VERTICAL BLINDS GETTING STARTED OPTIONAL HARDWARE A few simple tools are required: Corner End Cap Plastic Corner Aluminum Corner Steel Tape Measure Pencil Level (for outside mount) valence Return Corner

More information

Multiposition Air Actuator O-Ring Replacement

Multiposition Air Actuator O-Ring Replacement Technical Note 410 Valco Instruments Co. Inc. Multiposition Air Actuator O-Ring Replacement You will need: 1. 1/16", 7/64", and 9/64" hex drivers 2. 5/16", 3/8", 11/32", and 1/2" open end wrenches 3. 3/16"

More information

FRONT TURN SIGNAL RELOCATION KIT

FRONT TURN SIGNAL RELOCATION KIT -J0 REV. 00-0-0 FRONT TURN SIGNAL RELOCATION KIT GENERAL Kit Number -0 Models This kit fits 00 and later Dyna model motorcycles (except FXDSE), relocating the front turn signal from the handlebars to the

More information

Side Winder. Woodpeckers INSTALLATION INSTRUCTIONS

Side Winder. Woodpeckers INSTALLATION INSTRUCTIONS Woodpeckers PRECISION WOODWORKING TOOLS Side Winder Router Lift. INSTALLATION INSTRUCTIONS Models: SW350 COMPATIBLE ROUTER MOTORS The Woodpeckers Side Winder 350 Router Lift fits the Porter-Cable 690/890,

More information

Installation instructions, accessories - Handsfree for cellular phone, system B, entry level

Installation instructions, accessories - Handsfree for cellular phone, system B, entry level XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 0.5/1.1 2006 07 XC90 2003, XC90 2004 IMG-249663 Page 1 of 18 Required tools A0000162 A0000163 IMG-239664 M0000232 IMG-253123 IMG-252223 Page 2 of 18

More information

KTC Keyless Entry System

KTC Keyless Entry System Thank you for purchasing the Snap-on KTC Keyless Tool Control System. The information contained in these instructions is intended to serve as a guide so as to allow the electronic lock feature to be quickly

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. INSTALLATION INSTRUCTIONS HEATED GRIP WITH THERMOSTAT P/N 08T50-MCA-102 GL1800 Honda Dealer: Please give a copy of these instructions to your customer. Issue Date

More information

Assembly Instructions for Model: VMSA

Assembly Instructions for Model: VMSA Assembly Instructions for Model: VMSA Thank you for choosing a Sanus Systems Vision Mount wall mount. The VMSA is designed to mount up to 50 [1270 mm] Flat panel televisions weighing up to 150 lbs. [68.2

More information

GSM-EXT Cable Assembly Installation Guide

GSM-EXT Cable Assembly Installation Guide GSM-EXT Cable Assembly Installation Guide For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/mywebtech General Information The GSM-EXT cable assembly is used to connect

More information

Intel RAID Maintenance Free Backup Unit 4 Quick Installation User's Guide

Intel RAID Maintenance Free Backup Unit 4 Quick Installation User's Guide Intel RAID Maintenance Free Backup Unit 4 Quick Installation User's Guide Thank you for buying an Intel RAID Maintenance Free Backup Unit 4. The Intel RAID Maintenance Free Backup Unit 4 supports the Intel

More information

BODY-12, Door Handle - Removal, Installation, and Adjustment

BODY-12, Door Handle - Removal, Installation, and Adjustment Introduction BODY-12, Door Handle - Removal, Installation, and Adjustment There are many different procedures floating around describing how to replace the door handles on a 944 and every one of them will

More information

with installation dynafact boost GAUGE this manual is for use with systems 64050-64054

with installation dynafact boost GAUGE this manual is for use with systems 64050-64054 owners manual with installation instructions dynafact boost GAUGE this manual is for use with systems 64050-64054 GENERAL INSTALLATION PRACTICES This manual is an installation guide for all 1. Banks DynaFact

More information

FRU 01 Computer Cover. Removal: Computer Cover

FRU 01 Computer Cover. Removal: Computer Cover FRU 01 Computer Cover Removal: Computer Cover 1) Remove two retaining screws. 2) Press the Computer Cover release button and hold it in. 3) Pull the cover towards the rear and pivot upwards to remove it.

More information

INSTALLATION INSTRUCTIONS WOOD BLINDS AND FAUX WOOD BLINDS

INSTALLATION INSTRUCTIONS WOOD BLINDS AND FAUX WOOD BLINDS INSTALLATION INSTRUCTIONS WOOD BLINDS AND FAUX WOOD BLINDS STANDARD CORDLESS LIFT Thank you for your purchase. This blind has been custom built for you from the highest quality materials. To avoid errors

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-644) Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, GMC Yukon, Chevrolet Silverado, GMC Sierra 2000 05 General Tech Tips: Use painter s tape rather than

More information

ASSEMBLY INSTRUCTIONS FOR L&L EASY-FIRE AND SCHOOL-MASTER KILNS

ASSEMBLY INSTRUCTIONS FOR L&L EASY-FIRE AND SCHOOL-MASTER KILNS TABLE OF CONTENTS TOOLS NEED FOR THE JOB................. 1 UNPACKING................................ 2 INSPECT FOR VISIBLE DAMAGE.................. 2 CONTENTS OF THE SHIPMENT.................. 2 REMOVE

More information

Range Road RR Series Semi-Automatic Firewood Processor. Crated Unit Assembly Manual

Range Road RR Series Semi-Automatic Firewood Processor. Crated Unit Assembly Manual Range Road RR Series Semi-Automatic Firewood Processor Crated Unit Assembly Manual 1 1) Undo 8-18mm x 19mm Nuts and bolts, 2 on each leg of top frame 2) Lift top of Metal crate off and move out of work

More information

INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5

INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to

More information

EZ-Steer Assisted Steering System

EZ-Steer Assisted Steering System EZ-Steer Assisted Steering System Installation Instructions Platform Kit P/N 53059-54 Case IH CVX 1135 CVX 1145 CVX 1155 CVX 1170 CVX 1190 CVX 1195 CVX 135 CVX 145 CVX 155 CVX 175 CVX 195 New Holland TVT

More information

SERVICE GUIDE For WARN PULLZALL 120v AC &100v AC P/N 685000 & 685001

SERVICE GUIDE For WARN PULLZALL 120v AC &100v AC P/N 685000 & 685001 SERVICE GUIDE For WARN PULLZALL 120v AC &100v AC P/N 685000 & 685001 REPAIR / REPLACEMENT INSTRUCTIONS TROUBLE SHOOTING GUIDE 986765A2.doc Page 1 of 50 WARNING This guide identifies potential hazards and

More information

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly Replacing the Cover Micro-Switch To remove and replace the Cover Micro-Switch you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) #1 Phillips screwdriver (magnetic tip preferred)

More information

INSTALLATION INSTRUCTIONS. WOOD BLINDS 1-3/8, 2 and 2-3/8 SLAT SIZES. COMPOSITE FAUX WOOD BLINDS 2 and 2-1/2 SLAT SIZES

INSTALLATION INSTRUCTIONS. WOOD BLINDS 1-3/8, 2 and 2-3/8 SLAT SIZES. COMPOSITE FAUX WOOD BLINDS 2 and 2-1/2 SLAT SIZES INSTALLATION INSTRUCTIONS WOOD BLINDS 1-3/8, 2 and 2-3/8 SLAT SIZES COMPOSITE FAUX WOOD BLINDS 2 and 2-1/2 SLAT SIZES POLYMER FAUX WOOD BLINDS 2 and 2-1/2 SLAT SIZES STANDARD CORDLESS LIFT Thank you for

More information

* * AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS

* * AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS 16 1 AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light

More information

Inspiron 13. Service Manual. 7000 Series. Computer Model: Inspiron 13 7348 Regulatory Model: P57G Regulatory Type: P57G001

Inspiron 13. Service Manual. 7000 Series. Computer Model: Inspiron 13 7348 Regulatory Model: P57G Regulatory Type: P57G001 Inspiron 13 7000 Series Service Manual Computer Model: Inspiron 13 7348 Regulatory Model: P57G Regulatory Type: P57G001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps

More information

Control Box Wiring For PRSstandard Tool

Control Box Wiring For PRSstandard Tool 888-680-4466 ShopBotTools.com Control Box Wiring For PRSstandard Tool Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Introduction:...5 Installation:...5

More information

Written By: Walter Galan

Written By: Walter Galan Installing iphone 4S Display Assembly Written By: Walter Galan TOOLS: Phillips 00 Screwdriver (1) Plastic Opening Tools (1) PARTS: iphone 4S Display Assembly (1) iphone 4 and 4S Screen Protector (1) Small

More information

3. Loosen 3 x grub screws in the Dec end cap and unscrew the cap and counterweight shaft. NEQ6 Belt Modification Kit.

3. Loosen 3 x grub screws in the Dec end cap and unscrew the cap and counterweight shaft. NEQ6 Belt Modification Kit. NEQ6 Belt Modification Kit. Thank you for your purchase. Please read these instructions fully before fitting. Your package should contain 2 off 47 & 2 off 12 tooth aluminium pulleys 2 off belts 6mm wide

More information

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER 14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------

More information

Model A Turn Signal Kit Installation Guide

Model A Turn Signal Kit Installation Guide Model A Turn Signal Kit Installation Guide Consumer Hot Line: 888-471-LOGO 770-476-7322 In Atlanta, GA http://www.logolites.com P/N: 100-005/G 2003 3407 Hwy. 120 Duluth, GA 30096, USA Logo Lites and the

More information

9,000lb capacity 4 Post Lift Installation Manual

9,000lb capacity 4 Post Lift Installation Manual 9,000lb capacity 4 Post Lift Installation Manual Parts Checklist 1 Main side track with 9/16 hole on cylinder end complete with cylinder, hose and connector 1 Offside track 2 Cross Rails pre-assembled

More information

Replacing the Gateway M320 Keyboard

Replacing the Gateway M320 Keyboard Replacing the Gateway M320 Keyboard This package includes a replacement keyboard for your Gateway M320 notebook and these printed instructions. Tools you need You need a small Phillips and a small flat-blade

More information

Gripper Kit for the Boe-Bot Robot (#28202)

Gripper Kit for the Boe-Bot Robot (#28202) 599 Menlo Drive, Suite 100 Rocklin, California 95765, USA Office: (916) 624-8333 Fax: (916) 624-8003 General: info@parallax.com Technical: support@parallax.com Web Site: www.parallax.com Educational: www.stampsinclass.com

More information

UPGRADING AND SERVICING GUIDE

UPGRADING AND SERVICING GUIDE UPGRADING AND SERVICING GUIDE HPTouchSmart 610 PC Computer features may vary by model. Removing and Replacing a CD/DVD Drive...2 Removing the CD/DVD Drive... 2 Installing a New CD/DVD Drive... 5 Removing

More information

Guide for Modified Assembly: Lightning McQueen. By: Collin Patterson, University of Delaware. Materials and Tools:

Guide for Modified Assembly: Lightning McQueen. By: Collin Patterson, University of Delaware. Materials and Tools: Guide for Modified Assembly: Lightning McQueen By: Collin Patterson, University of Delaware Materials and Tools: PVC o 40 inches of 1 in diameter PVC o 25 inches of ¾ in PVC o 4 x 1 in elbows o 2 x ¾ in

More information

Installation Instructions

Installation Instructions Installation Instructions GL18007-30 Trailer Hitch 440 South Pine Street Burlington, WI 53105 262-763-8222 rivcoproducts.com 2012 & NEWER GL1800 TRAILER HITCH INSTALLATION INSTRUCTIONS #GL18007-30 Read

More information