FERROXCUBE DATA SHEET. EC35 EC cores and accessories. Supersedes data of September Sep 01

Transcription

1 FERROXCUBE DATA SHEET Supersedes data of September Sep 01

2 CORE SETS Effective core parameters SYMBOL PARAMETER VALUE UNIT Σ(I/A) core factor (C1) mm 1 V e effective volume 6530 mm 3 I e effective length 77.4 mm A e effective area 84.3 mm 2 A min minimum area 71 mm 2 m mass of core half 19 g max MGC397 Fig.1 core half. Core halves A L measured in combination with an non-gapped core half, unless stated otherwise. GRADE A L (nh) Note 1. Measured in combination with an equal gapped core half (symmetrical air gap). Properties of core sets under power conditions 2008 Sep µ e TOTAL AIR GAP (µm) TYPE NUMBER 3C ± 3% (1) C81-E ± 3% (1) C81-E ± 3% C81-A ± 5% C81-A ± 10% C81-A C81 3C ± 3% (1) C90-E ± 3% (1) C90-E ± 3% C90-A ± 5% C90-A ±10% C90-A ±25% C90 B (mt) at CORE LOSS (W) at GRADE H=250A/m; f = 25 khz; f=100khz; f = 25 khz; Bˆ = 200 mt; Bˆ = 100 mt; T = 100 C T = 100 C T=100 C 3C C

3 COIL FORMERS General data 8-slots coil former for insertable pins PARAMETER Coil former material Maximum operating temperature SPECIFICATION polyamide (PA6.6), glass-reinforced, flame retardant in accordance with UL 94V-0 ; UL file number E44716(M) 130 C, IEC 60085, class B handbook, full pagewidth max max 34.0 ref max max 9.85 min ± 0.25 MGB689 Fig.2 coil former; 8-slots. Winding data and area product for 8-slots coil former for insertable pins Coil formers with inserted pins are available on request. NUMBER OF SECTIONS MINIMUM WINDING AREA (mm 2 ) NOMINAL WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) AREA PRODUCT Ae x Aw (mm 4 ) CP--1S TYPE NUMBER 2008 Sep

4 MOUNTING PARTS General data and ordering information ITEM REMARKS MOUNT FIGURE TYPE NUMBER Insertable pins solderability: IEC , Part 2, general 3 PIN-EC Test Ta, method 1; material: copper-zinc alloy (CuZn), tin (Sn) plated horizontal 4 PIN/H-EC Base plate 2 holes aluminium 5 BPL2- Base plate 4 holes aluminium 6 BPL4- Clamp copper-zinc alloy (CuZn) 7 CLM/U MGB MGB Fig.3 EC pin; general mount. Fig.4 EC pin; horizontal mount MGB540 1 MGB541 1 Fig.5 base plate; 2 holes. Fig.6 base plate; 4 holes Sep

5 42.2 Ø min 3-48 NC 2A THD 2 PLACES 32.4 MGB536 Fig.7 clamp Sep

6 DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS Preliminary specification PRODUCT STATUS Development DEFINITIONS This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype Design-in Preferred Support These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. These products are recommended for new designs. These products are recommended for use in current designs and are available via our sales channels. These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability Sep