REMOTE CONTROLLER CS343-R51M-UL OWNER S MANUAL

Transcription

1 WNER S MANUAL REMTE CNTRLLER Please read this wner's Manual carefully before operation. Save this manual in a safe place for future reference. CS-RM-UL

2 CNTENTS Remote Controller Specification... Performance Features Features of the Remote controller Buttons... Indicators on Display panel... perating the Remote Controller... Warning Set the starting & stopping time. Push the TIMER N button, the remote controller will show TIMER N, the last set time for START operation and the signal "h" will be shown on the DIGITAL display area. You are now ready to readjust the TIMER N to start the operation.. Push the TIMER N button again to set the time you want to start the operation.. Push the TIMER FF button, the remote controller will show TIMER FF, the last set time for STP operation and the signal "h" will be shown on the DIGITAL display area. You are now ready to reset the time to STP operation.. Push the TIMER FF button again to set the time you want to stop the operation.. After setting the TIMER, there will be a one-half second delay before the remote controller transmits the signal to the Air Conditioner. Then, after approximately another seconds, the signal "h" disappears and the set temperature will re-appear on the digital display. Change the TIMER To change the TIMER N/FF time, just press the corresponding TIMER button and reset the time. To cancel the TIMER N/FF setting, just adjust the TIMER time to 0:00. NTE The setting time is relative time. That is the time set is based on the delay of the current time. Warning. Be sure there are no obstacles between the remote controller and the receiver of indoor unit otherwise the air conditioner will not work.. Keep the Remote Controller away from any liquids.. Protect the remote controller from the high temperatures and exposure to radiation.. Keep the indoor receiver out of direct sunlight or the Air Conditioner may malfunction.. Keep Remote Controller away from EMI(Electro-Magnetic Interference) supplied by other household appliances.

3 Remote Controller Specification Model Rated Voltage Lowest Voltage of CPU Emitting Signal Transmission Distance Environment Performance Features Features of Remote controller buttons UL-RM/(C)E.0V(Alkaline dry batteries LR0 ).0V 8m (when using.0 voltage, it Gets m) - F~0 F. perating Mode: AUT CL DRY HEAT(Cooling only model without) and FAN.. Timer Setting Function in hours.. Indoor Setting Temperature Range: F~ 88 F. Full function of LCD (Liquid Crystal Display) AUT CL DRY HEAT SET TEMPERATURE( F) TEMP FAN HIGH MED LW 9 MDE N/FF FAN SPEED 8 SWING SLEEP TIMER N 0 TIMER FF RESET LCK AIR LED DIRECTIN DISPLAY TURB Fig TEMP Button : Push this button to decrease the indoor temperature setting. TEMP Button : Push this button to increase the indoor temperature setting. MDE Selection Button: Each time the button is pressed, the operation mode is shifted in the direction of the arrow: AUT CL DRY HEAT FAN NTE: CL only model has no HEAT feature. SWING Button: Push this switch button to change the louver angle. RESET Button: When you press the recessed RESET button, all current settings are cancelled and the control will return to the initial settings. AIR DIRECTIN Button: Press this button and release it quickly, the directional swing feature of the horizontal louver is activated. The louver swings for a certain angle for each press. If keep pressing the button for more than seconds, the Auto swing feature will be activated. Press it again, the louver stops moving. When the louver swing at a position which would affect the cooling and heating effect of the air conditioner, it would automatically change the swing direction (Not applicable to units without this function). LED DISPLAY Button: Press this button to clear the digit display in the air conditioner, press it again to activate it (Not applicable to units without this function). FAN SPEED Button: Used to select the Fan Speed in four steps- AUT LW MED or HIGH. Each time the button is pressed, the fan speed mode is shifted. N/FF Button: Push this button to start operation, push the button again to stop operation. TIMER N Button: Press this button to initiate the auto-on time sequence. Each press will increase the auto-timed setting in 0 minutes increments. When the setting time displays 0:00, each press will increase the auto-timed setting 0 minutes increments. To cancel the auto-timed program, simply adjust the auto-on time to 0:00. SLEEP Button: Press this button to go into the Energy-Saving operation mode. Press it again to cancel. This function is only can be used on CL, HEAT and AUT mode and maintain the most comfortable temperature for you. NTE: While the unit is running under SLEEP operation mode, it would be canceled if you press the other button.

4 TIMER FF Button: Press this button to initiate the auto-off time sequence. Each press will increase the auto-timed setting in 0 minutes increments. When the setting time displays 0:00, each press will increase the auto-timed setting 0 minutes increments. To cancel the auto-timed program, simply adjust the auto-off time to 0:00 LCK Button: When you press the recessed LCK button, all current settings are locked in and the remote controller does not accept any operation except that of the LCK. Press again to cancel the LCK mode. Indicators on Display Panel DIGITAL DISPLAY area TRANSMI- SSIN Indicator PERATIN MDE Indicator LCK Indicator TIMER DISPLAY Indicator TURB Button: Push this button on CL mode, the air conditioner goes into powerful cooling operation. Push again to cancel the TURB function.n all models except MSG-CRN & MSG-HRN. Display Panel TIMER N FF Fig. N/FF Indicator FAN SPEED Indicator DIGITAL DISPLAY area: This area will show the set temperature and, if in the TIMER mode, will show the N and FF settings of the TIMER. If in the FAN mode, nothing is appeared. TRANSMISSIN Indicator: This indicator flashes one time when remote controller transmits signals to the indoor unit. PERATIN MDE Indicator N/FF Indicator: This symbol appears when the unit is turned on by the remote controller, and disappear when the unit is turned off. PERATIN MDE Indicator: When press the MDE button, it shows the current operating mode -- AUT CL DRY HEAT (Cooling only model without) mode. LCK Indicator: LCK display is displayed by pushing the LCK button. Push the LCK button to clear display. TIMER DISPLAY Indicator: This display area shows the settings of the TIMER. That is, if only the starting time of operation is set, it will display the TIMER N. If only the turning off time of operation is set, it will display the TIMER FF. If both operations are set, it will show TIMER N-FF which indicates you have chosen to set both the starting time and off time. FAN SPEED Indicator: Press the FAN SPEED button to select the desired fan speed setting (Auto-Low-Med-High). You selection will be displayed in the LCD window except the Auto fan speed. NTE: All signs shown in the Fig. is for the purpose of clear presentation. But during the actual operation only the relative functional signs are shown on the display panel. perating the Remote Controller Install/Replace Batteries The Remote Controller uses two alkaline dry batteries(lr0x).. To install the batteries, slide the back cover of the battery compartment and install the batteries according the direction (+and -)shown on the Remote Controller.. To replace the old batteries, use the same method as mentioned above. NTE. When replacing batteries, do not use old batteries or a different type battery. This may cause the remote control to malfunction.. If you do not use the remote controller for several weeks remove the batteries. therwise battery leakage may damage the remote controller.. The average battery life under normal use is about months.. Replace the batteries when there is no answering beep from the indoor unit or if the Transmission Indicator light fails to light.

5 AUTMATIC PERATIN Switch on the power and the PERATIN indication lamp on the display panel of the indoor unit starts flashing, and turns off after flashes for times.. Use the MDE button to select AUT.. Push the TEMP button to set the desired room temperature. The most comfortable temperature settings are between 0 F to 8 F.. Push the N/FF button to start the air conditioner. The PE- RATIN lamp on the display panel of the indoor unit lights. The FAN SPEED is automatically set and there are no fan speed indicators shown on the display panel of the remote controller.. Push the N/FF button again to stop the unit operation. NTE. In the AUT mode, the air conditioner can logically choose the mode of CL, FAN and HEAT by sensing the difference between the actual ambient room temperature and the set temperature on the remote controller.. If the AUT mode is not comfortable for you, the desired mode can be selected manually. CL/ HEAT (Cooling only model without) and FAN peration. If the AUT mode is not comfortable, you may manually over-ride the settings by using CL, HEAT or FAN modes.. Push the TEMP button to set the desired room temperature. When in CLING mode, the most comfortable settings are 0 F or above. When in HEATING mode, the most comfortable settings are 8 F or below.. Push the FAN SPEED to select the FAN mode of AUT, HIGH, MED or LW.. Push the N/FF button, the operation lamp lights and the air conditioner start to operate as your settings. Push the N/FF button again to stop this unit operation. NTE The FAN mode can not be used to control the temperature. While in this mode, only steps and may be performed. DRY peration. Push the MDE button to select DRY.. Push the TEMP button to set the desired temperature from 0Fto8F.. Push the N/FF button, the PERATIN lamp lights and the air conditioner starts to operate in DRY mode at LW fan speed. Push the N/FF button again to stop this unit operation. NTE Due to the difference of the set temperature of the unit and the actual indoor temperature, the Air Conditioner when in DRY mode will automatically operate many times without running the CL and FAN mode. TIMER peration Push TIMER N button to set the auto- on time and TIMER FF button to set the auto-off time.. To set the starting time.. Push the TIMER N button, then the remote controller shows TIMER N, the last set time for the starting operation and the signal "h" will be shown on the DIGITAL DISPLAY area. You are now ready to reset the time to START the operation.. Push the TIMER N button again to set desired unit start time.. After setting the TIMER N,there will be a one-half second delay before the remote controller transmits the signal to the air conditioner. Then, after approximately another seconds, the signal "h" disappears and the set temperature will re-appear on the digital display.. To set the stopping time.. Push the TIMER FF button and the remote controller will show TIMER FF, the last set time for the stopping operation and the signal "h" will be shown on the DIGITAL DISPLAY area. You are now ready to reset the time of the STP operation.. Push the TIMER FF button again to set the time you want to stop the operation.. After setting the TIMER FF,there will be a one-half second delay before the remote controller transmits the signal to the air conditioner. Then, after approximately another seconds, the signal "h" disappears and the set temperature will re-appear on the digital display.