for Arduino General purpose INPUT - OUTPUT shield for Arduino
|
|
- Darrell Kelly
- 7 years ago
- Views:
Transcription
1 KA0 ILLUSTRATED LUSTR TED ASSEMBLY SE MANUAL HKA0P KA0 IN/OUT shield for Arduino General purpose INPUT - OUTPUT shield for Arduino Features For use with Arduino Due, Arduino Uno, Arduino Mega analog inputs digital input relay contact outputs Indicator leds for relay outputs and digital inputs Specifications Analog inputs: 0..+VDC Digital inputs: dry contact or open collector Relays: V Relay contacts: NO/NC VDC/A max. Dimensions: 8 x mm /.7 x.08
2 Forum Participate our Velleman Projects Forum Subscribing our newsletter?, visit
3 Velleman N.V. Legen Heirweg 9890 Gavere (België)
4 assembly hints. Assembly (Skipping this can lead to troubles! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.. Make sure you have the right tools: A good quality soldering iron (-0W) with a small tip. Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called thinning and will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning. Thin raisin-core solder. Do not use any fl ux or grease. A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fl y towards the eyes. Needle nose pliers, for bending leads, or to hold components in place. Small blade and Phillips screwdrivers. A basic range is fi ne. For some projects, a basic multi-meter is required, or might be handy. Assembly Hints : Make sure the skill level matches your experience, to avoid disappointments. Follow the instructions carefully. Read and understand the entire step before you perform each operation. Perform the assembly in the correct order as stated in this manual Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. Values on the circuit diagram are subject to changes, the values in this assembly guide are correct* Use the check-boxes to mark your progress. Please read the included information on safety and customer service * Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as NOTE on a separate leaflet.. Soldering Hints :. Mount the component against the PCB surface and carefully solder the leads Make sure the solder joints are cone-shaped and shiny. Trim excess leads as close as possible to the solder joint - -
5 DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR VALUE ON THE PARTS LIST! - -
6 Construction I CONSTRUCTION Zenerdiodes Transistors Ceramic capacitor c... ZD : V ZD : V ZD : V ZD : V ZD : V ZD : V T: BC7B T: BC7B T: BC7B T: BC7B T: BC7B T: BC7B c... C: 00nF (0) Diodes D : N8 D : N8 D : N8 D : N8 Watch the polarity! D : N8 D : N8 D7 : N8 D8 : N8 D9 : N8 D0: N8 D: N8 D: N8 Watch the polarity! C (-) C (-) LED LD : Red LD : Red LD : Red LD : Red LD : Red LD : Red Watch the polarity! LD7 : Green LD8 : Green LD9 : Green LD0 : Green LD : Green LD : Green - - Resistors R... R : K ( B) R : K ( B) R : K ( B) R : K ( B) R : K ( B) R : K ( B) R7 : ( B) R8 : 0K ( B) R9 : ( B) R0 : 0K ( B) R : ( B) R : 0K ( B)
7 Construction R: R: R: R: R7: R8: R9: R0: R: R: R: R: R: R: R7: R8: R9: R0: 0K 0K 0K ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) ( B) 7 Terminal blocks 8 x p (INPUTS) 8 Relays 9 Electrolytic capacitors RY RY RY RY RY RY Watch the polarity! C : 00μF! 0 Male header CUT CUT CUT CUT X pins X 8 pins x p (OUTPUTS) -7-
8 Connection diagram II CONNECTION DIAGRAM OUTPUT MAX. VDC / A DIGITAL INPUTS RELAY OUTPUTS (Max. VDC/A) DIGITAL INPUTS ANALOG INPUTS 0... V ANALOG INPUTS ANALOG DOWNLOAD SAMPLE CODE FROM KA0 PAGE ON
9 - 9 - SK V V RST SK A0 A A A A A 7 8 SK ARDUINO UNO 7 8 SK AREF - V LEDRL LD7 LEDRL LD8 LEDRL LD9 LEDRL LD0 LEDRL LD LEDRL LD R9 R0 R R R R - N8 D N8 D N8 D N8 D N8 D N8 D 7 DI DI DI DI DI DI R R R7 R8 R9 R0 AI AI AI AI AI AI A0 A A A A A.V 0.W ZD.V 0.W ZD.V 0.W ZD.V 0.W ZD.V 0.W ZD.V 0.W ZD BC7 T BC7 T BC7 T BC7 T BC7 T BC7 T 0K R8 0K R0 0K R 0K R 0K R 0K R8 R7 R9 R R R R7 N8 D7 N8 D8 N8 D9 N8 D0 N8 D N8 D LEDRL LD LEDRL LD LEDRL LD LEDRL LD LEDRL LD LEDRL LD K R K R K R K R K R K R n C 00μ/-V C SK SK7 SK SK8 SK9 SK0 JP SK JP SK JP SK JP SK JP SK JP SK JP SK7 JP SK8 - AI AI AI AI AI AI - DI DI DI DI DI DI - V RELAY TSCDH RY RELAY TSCDH RY RELAY TSCDH RY RELAY TSCDH RY RELAY TSCDH RY RELAY TSCDH RY Schematic diagram
10 PCB - 0 -
11 Leds and how to use them Leds feature a specific voltage drop, depending on type and colour. Check the datasheet for exact voltage drop and rated current! Never connect leds in parallel How to Calculate the series resistor: Example: operate a red led (.7V) on a 9Vdc source. Required led current for full brightness: ma (this can be found in the datasheet of the led) Supply voltage (V) - led voltage (V) = series resistance (ohms) required current (A) 9V -.7V = 0 ohm 0.00A Required resistor power handling= voltage over resistor x current passed trough resistor (9V -.7V) x 0.00A = 0.0W closest value : use a k resistor a standard /W resistor will do the job open collector outputs An open collector output can be compared to a switch which switches to ground when operated LEDs in series: Example: x red led (.7V) on 9V battery Required led current for full brightness: ma (this can be found in the datasheet of the led) Example: How to switch an LED by means of an open collector output Supply voltage (V) - (number of leds x led voltage (V)) = series resistance (ohms) required current (A) 9V - ( x.7v) = 780 ohm 0.00A use an 80 ohm resistor
12 The new Velleman Projects catalogue is now available. Download your copy here: Modifi cations and typographical errors reserved - Velleman nv. HKA0 IP Velleman NV, Legen Heirweg Gavere.
MAINS VOLTAGE DETECTOR K7101
With this device wires can be very easily checked for mains voltage. H7101IP-1 MAINS VOLTAGE DETECTOR K7101 VELLEMAN NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com
More informationDUAL ELECTRONIC DICE K3400
DUAL ELECTRONIC DICE K3400 Cheating is no longer possible! ILLUSTRATED ASSEMBLY MANUAL H3400IP-1 VELLEMAN NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com Features &
More informationTotal solder points: 205 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL BATTERY CHARGER / DISCHARGER K7300 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 205 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL BATTERY CHARGER / DISCHARGER K7300 Automatic (dis)charging of both NiCd and NiMH batteries. ILLUSTRATED ASSEMBLY MANUAL
More informationSYMMETRIC 1A POWER SUPPLY K8042
SYMMETRIC 1A POWER SUPPLY K8042 Low cost universal symmetric power supply ILLUSTRATED ASSEMBLY MANUAL H8042IP-1 Features & Specifications Features low cost universal symmetric power supply just add a suitable
More informationK8025 VIDEO PATTERN GENERATOR. Check the picture quality of your monitor or TV, ideal for adjustment or troubleshooting.
K8025 ILLUSTRATED ASSEMBLY MANUAL H8025IP 1 VIDEO PATTERN GENERATOR Check the picture quality of your monitor or TV, ideal for adjustment or troubleshooting. Forum Participate our Velleman Projects Forum
More informationTotal solder points: 67 Difficulty level: beginner 1 2 3. 4 5 advanced UNIVERSAL TEMPERATURE SENSOR K8067 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 67 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL TEMPERATURE SENSOR K8067 Ideal for connection to computer interface boards (K8000, K8055, K8047,..) ILLUSTRATED ASSEMBLY
More informationTotal solder points: 115 Difficulty level: beginner 1 2 3 4 5 advanced 4 CHANNEL RUNNING LIGHT K8032 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 115 Difficulty level: beginner 1 2 3 4 5 advanced 4 CHANNEL RUNNING LIGHT K8032 Ideal for creating disco light effects, light speed adjustable. Suited for inductive loads. ILLUSTRATED
More informationTotal solder points: 18 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL POWER SUPPLY 5-14DC / 1A K2570 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 18 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL POWER SUPPLY 5-14DC / 1A K2570 The easy way to power your projects. ILLUSTRATED ASSEMBLY MANUAL H2570IP-1 Features & Specifications
More informationTotal solder points: 147 Difficulty level: beginner 1 2 3 4 5 advanced VIDEO SIGNAL CLEANER K8036 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 147 Difficulty level: beginner 1 2 3 4 5 advanced VIDEO SIGNAL CLEANER K8036 Digitally cleans the video signal of unwanted distortions and improves the picture quality. ILLUSTRATED
More informationK2570 UNIVERSAL POWER SUPPLY 5-14DC / 1A. The easy way to power your ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 18 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL POWER SUPPLY 5-14DC / 1A K2570 The easy way to power your projects. ILLUSTRATED ASSEMBLY MANUAL H2570IP-1 Features & Specifications
More informationTotal solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 Control a relay by means of the wellknown DMX512 protocol. ILLUSTRATED ASSEMBLY MANUAL H8072IP-1 Features
More informationK4401 SOUND GENERATOR. them at the touch of a button. Specifications
SOUND GENERATOR K4401 Sound effects, tunes, sirens... 10 of them at the touch of a button. Specifications Loudspeakers output : 8 ohm/1w Line output : 1VRms. Power supply : 8 10VDC (9v battery). Max. current
More informationGUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102
H4102IP-1 GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 Practice the guitar without disturbing others. Features & Specifications Features: An electric guitar cannot be connected to just any amplifier
More informationTotal solder points: 248 Difficulty level: beginner 1 2 3 4 5 advanced. 15 Channel infrared receiver K8050 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 48 Difficulty level: beginner 4 5 advanced 5 Channel infrared receiver K8050 IR-Remote control transmitters allow you to control 5 opencollector contacts ILLUSTRATED ASSEMBLY MANUAL
More informationPOCKET AUDIO GENERATOR K8065
POCKET AUDIO GENERATOR K8065 Great little gadget for service repair, testing, education, etc... ILLUSTRATED ASSEMBLY MANUAL H8065IP-1 VELLEMAN NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be
More informationTotal solder points: 57 Difficulty level: beginner 1 2 3 4 5 advanced 3 TO 30VDC / 3A POWER SUPPLY K7203 ILLUSTRATED ASSEMBLY MANUAL H7203IP-1
Total solder points: 57 Difficulty level: beginner 1 2 3 4 5 advanced 3 TO 30VDC / 3A POWER SUPPLY K7203 A power supply for all our kits, based on a stabilised DC voltage of 30V. ILLUSTRATED ASSEMBLY MANUAL
More informationVOLUME AND TONE CONTROL - PREAMPLIFIER K8084
H8084IP-1 VOLUME AND TONE CONTROL - PREAMPLIFIER K8084 When using one of our amplifiers (big or small), you always need a volume control and preferably also a tone control Features & specifications When
More information400W MONO/STEREO AMPLIFIER
400W MONO/STEREO AMPLIFIER Universal, robust and compact are the words to describe this amplifier. Total solder points: 264 Difficulty level: beginner 1 2 3 4 5 advanced K4005B ILLUSTRATED ASSEMBLY MANUAL
More information15 Channel IR transmitter. Total solder points: 53 Difficulty level: beginner 1 2 3 4 5 advanced K8049 ILLUSTRATED ASSEMBLY MANUAL
15 Channel IR transmitter Compatible with most Velleman IR receiver kits, 4 adresses allow the use of multiple receivers in one room. Total solder points: 53 Difficulty level: beginner 1 2 3 4 5 advanced
More informationTotal solder points: 129 Difficulty level: beginner 1 2 3 4 5 advanced LIQUID LEVEL CONTROLLER K2639 ILLUSTRATED ASSEMBLY MANUAL H2639IP-1
Total solder points: 129 Difficulty level: beginner 1 2 3 4 5 advanced LIQUID LEVEL CONTROLLER K2639 Forgotten to turn off the tap, leaking washing machines,... Prevention is better than cure. So use this
More information200W DISCRETE POWER AMPLIFIER K8060
H8060IP-1 200W DISCRETE POWER AMPLIFIER K8060 Ideal for active speaker system or subwoofer, guitar amp, home theatre systems, instrument amp, etc. Features & Specifications Specifications: Excellent value
More informationThe new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu
The new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu Modifications and typographical errors reserved - Velleman nv. H8098 IP 2 (rev.1.0) Velleman NV, Legen
More information7-SEGMENT DIGITAL CLOCK
57mm 7-SEGMENT DIGITAL CLOCK Large 57mm clock & temperature display with extra unique feature Total solder points: 263 Difficulty level: beginner 1 2 3 4 5 advanced K8089 ILLUSTRATED ASSEMBLY MANUAL H8089IP-1
More informationTotal solder points: 85 Difficulty level: beginner 1 2 3 4 5 advanced MULTIFUNCTION RELAY SWITCH K8015 ILLUSTRATED ASSEMBLY MANUAL H8015IP-2
Total solder points: 85 Difficulty level: beginner 1 2 3 4 5 advanced MULTIFUNCTION RELAY SWITCH K8015 14 Different functions including timers, switching, flashing, interval, random switching,... ILLUSTRATED
More informationWith the K8097 4-channel stepper motor card you can drive 4 stepper motors via USB, and monitor and assign actions if needed to 5 dry contacts
K8097 K80977IP ILLUSTRATED LU TED ASSEMBLY SEMB MANUAL H8097IP - Channel USB stepper motor card With the K8097 -channel stepper motor card you can drive stepper motors via USB, and monitor and assign actions
More informationK6002 TEMPERATURE CONTROLLER. Specifications
Total solder points: 169 + 99 + 67 Difficulty level: beginner 1 2 3 4 5 advanced TEMPERATURE CONTROLLER K6002 Unlike a normal thermostat, this kit has two outputs, one for "high" alarm and one for "low"
More informationPC FUNCTION GENERATOR
PC FUNCTION GENERATOR Create standard signal waves like e.g. sine, triangle and rectangle are available; other sine waves can be easily created with integrated software. Total solder points: 954 Difficulty
More informationELECTRONIC TRANSISTOR IGNITION FOR CARS K2543
H2543IP 1 ELECTRONIC TRANSISTOR IGNITION FOR CARS K2543 Gives your car a better starting and smoother running. Suitbale for 12V and 6V systems. Features & Specifications Even the most sceptical one has
More informationK8068 BUS DIMMER FOR HOME MODULAR LIGHT SYSTEM ILLUSTRATED ASSEMBLY MANUAL H8068IP-1
Total solder points: 74 Difficulty level: beginner 1 2 3 4 5 advanced BUS DIMMER FOR HOME MODULAR LIGHT SYSTEM K8068 PLUG - IN module for use with home modular lights system K8006. For electronic transformers!
More informationDIGITAL PC SCOPE. Total solder points: 625 Difficulty level: beginner 1 2 3 4 5 advanced K8031 ILLUSTRATED ASSEMBLY MANUAL
DIGITAL PC SCOPE Digital storage oscilloscoop, using a computer and its monitor to display waveforms. All standard oscilloscope functions are available in the Windows program supplied. Total solder points:
More informationPOWERBLOCK - POWER AMPLIFIER
POWERBLOCK - POWER AMPLIFIER This amplifier is an ideal set-up for active speaker use. Total solder points: 383 Difficulty level: beginner 1 2 3 4 5 advanced K8081 ILLUSTRATED ASSEMBLY MANUAL H8081IP-1
More informationDUAL ELECTRONIC DICE K3400
Total solder points: 198 Skill level : Beginner 1 2 3 4 5 Advanced DUAL ELECTRONIC DICE K3400 Features: Two independent dice Use a single or both dice at the same time Display auto shut-off saves battery
More informationDc to Pulse Width Modulator
Total solder points: 82 Difficulty level: beginner 1 2 3 4 5 advanced Dc to Pulse Width Modulator Hardware: K8004 PWM range: 0 to 100% PWM frequency: 100 to 5000Hz adjustable Minimum PWM offset: 0 to 20%
More informationFan timer K8041. Features: Specifications :
Total solder points: 101 Difficulty level: beginner 1 2 3 4 5 advanced Features: Fan timer K8041 Suitable for most types of ventilators Solid state switching with noise suppression Can be connected to
More informationTRANSISTOR IGNITION K2543
Total solder points: 38 Skill level : Beginner 1 2 3 4 5 Advanced HIGH-Q TRANSISTOR IGNITION K2543 Applications : Upgrade the existing ignition system of : Cars, motorcycles, mowers, outboards, Reduces
More informationK8048 PIC PROGRAMMER AND EXPERIMENT BOARD. Specifications
Total solder points: 274 Difficulty level: beginner 1 2 3 4 5 advanced PIC PROGRAMMER AND EXPERIMENT BOARD K8048 Suitable for programming Microchip Flash PIC TM microcontrollers. Basic programming knowledge
More information100W SUBWOOFER KIT. Total solder points: 383 Difficulty level: beginner 1 2 3 4 5 advanced K8077 ILLUSTRATED ASSEMBLY MANUAL
100W SUBWOOFER KIT Powerful bass from a small cabinet thanks to the dual speaker principle Total solder points: 383 Difficulty level: beginner 1 2 3 4 5 advanced K8077 ILLUSTRATED ASSEMBLY MANUAL H8077IP-1
More information3.5A SUPPRESSED DIMMER K8026
Total solder points: 29 Difficulty level: beginner 1 2 3 4 5 3.5A SUPPRESSED DIMMER K8026 Dimmer for incandescent lightbulbs and collector motors Fuse protected AC power : 110-125 or 220-240VAC 50/60Hz
More information4 channel recorder / logger
Total solder points: 159 Difficulty level: beginner 1 2 3 4 5 advanced 4 channel recorder / logger Hardware: USB connected and powered. Four DC coupled input channels. Input resistance 1Mohm. Maximum samples
More informationTotal solder points: 202 Difficulty level: beginner 1 2 3 4 5 advanced. PIC programmer board K8076 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 0 Difficulty level: beginner advanced PIC programmer board K0 This board can program a wide range of Microchip PIC microcontrollers ILLUSTRATED ASSEMBLY MANUAL H0IP- This device complies
More informationDC CONTROLLED DIMMER Manual
Total solder points: 61 Skill level : Beginner 1 2 3 4 5 Advanced K8003 DC CONTROLLED DIMMER Manual This small but handy circuit is ideal for replacing an existing dimmer or switch, in order to be able
More informationAssembly and User Guide
1 Amp Adjustable Electronic Load 30V Max, 1 Amp, 20 Watts Powered by: 9V Battery Assembly and User Guide Pico Load is a convenient constant current load for testing batteries and power supplies. The digital
More informationStereo valve power amplifier
Stereo valve power amplifier For most of us a high power valve amplifier is unaffordable. This kit changes that, so that now everybody can enjoy that sublime "valve sound". Total solder points: 00 Difficulty
More informationARDUINO SEVERINO SERIAL SINGLE SIDED VERSION 3 S3v3 (REVISION 2) USER MANUAL
ARDUINO SEVERINO SERIAL SINGLE SIDED VERSION 3 S3v3 (REVISION 2) USER MANUAL X1: DE-9 serial connector Used to connect computer (or other devices) using RS-232 standard. Needs a serial cable, with at least
More informationK8055 Specifications:
Total solder points: 159 Difficulty level: beginner 1 2 3 4 5 advanced USB Experiment interface board K8055 Specifications: 5 Digital inputs (0= ground, 1= open). On board test buttons provided. 2 Analog
More informationLIGHT COMPUTER K5201
Total solder points: 240 Skill level : Beginner 1 2 3 4 5 Advanced LIGHT COMPUTER K5201 Features: Sixteen different patterns and 7 outputs provide a unique light show Easy pattern selection with rotary
More informationMartin County Amateur Radio Association. Nightfire Kits 1 LED Torch Kit 270016. Contents. Description
Nightfire Kits 1 LED Torch Kit 270016 1 Contents Nightfire Kits LED Torch Kit 270016... 1 Description... 1 Safety and Assembly of the kit... 6 Required and Useful Tools... 7 Assembly... 8 Checkout and
More informationJoule Thief 3.0 Kit. June 2012, Rev 1 1 http://www.easternvoltageresearch.com Joule Thief 3.0
Kit Instruction Manual Eastern Voltage Research, LLC June 2012, Rev 1 1 http://www.easternvoltageresearch.com HIGH BRIGHTNESS LED THIS KIT USES A 1W CREE, HIGH BRIGHTNESS LED. DO NOT STARE AT THIS (OR
More informationDET Practical Electronics (Intermediate 1)
DET Practical Electronics (Intermediate 1) 731 August 2000 HIGHER STILL DET Practical Electronics (Intermediate 1) Support Materials CONTENTS Section 1 Learning about Resistors Section 2 Learning about
More informationElectronics and Soldering Notes
Electronics and Soldering Notes The Tools You ll Need While there are literally one hundred tools for soldering, testing, and fixing electronic circuits, you only need a few to make robot. These tools
More informationQUASAR ELECTRONICS KIT No. 1015 ELECTRONIC MOSQUITO REPELLER
QUASAR ELECTRONICS KIT No. 1015 ELECTRONIC MOSQUITO REPELLER General Description This simple circuit can prove itself worth many times its value (which is very reasonable anyway) in getting rid of mosquitoes
More informationKnight Audio Technologies Ltd. Deacy - Style Amplifier Kit Build Instructions
Knight Audio Technologies Ltd Deacy - Style Amplifier Kit Build Instructions Introduction Firstly, thank you for purchasing this amplifier kit. We have designed this amplifier based on the Mullard 1960
More informationAUTOMATIC CALL RECORDER JAMECO PART NO. 2163735
AUTOMATIC CALL RECORDER JAMECO PART NO. 2163735 Experience Level: Intermediate Time Required: 1-2 Hours This project automatically records phone calls. The program, along with the adapter records each
More information!Operation:!1. Connect an external power source to J1 (+ and - IN terminals). The
The CB500 Electronic Circuit Breaker is an resettable circuit breaker (fuse) that disconnects power when the trip setting is exceeded. There are 4 trip settings that can easily be changed and set during
More informationKit 106. 50 Watt Audio Amplifier
Kit 106 50 Watt Audio Amplifier T his kit is based on an amazing IC amplifier module from ST Electronics, the TDA7294 It is intended for use as a high quality audio class AB amplifier in hi-fi applications
More informationModifying the Yaesu FT-847 External 22.625 MHz Reference Input
Modifying the Yaesu FT-847 External 22.625 MHz Reference Input David Smith VK3HZ Introduction This document describes the modification of an FT-847 to allow an external 22.625 MHz Reference oscillator
More informationAXE114S BINARY CLOCK. revolution Revolution Education Ltd. Email: info@rev-ed.co.uk Web: www.rev-ed.co.uk Version 1.1 12/09/08 AXE114.PMD.
AXE114S BINARY CLOCK Features: The PICAXE binary clock kit tells the time by lighting up blue LEDs in a binary pattern. This is a useful tool for teaching students binary code or simply just confusing/
More informationCumbria Designs T-1. SSB/CW Filter kit (4.9152MHz) User Manual
Cumbria Designs T-1 SSB/CW Filter kit (4.9152MHz) User Manual CONTENTS 1 INTRODUCTION 2 2 CIRCUIT DESCRIPTION 2 3 ASSEMBLY 2 4 TESTING 4 The Steading Stainton PENRITH Cumbria CA11 0ES UK 1 Introduction
More informationWHO ANSWERED FIRST? FIND OUT WITH THIS QUIZ BUZZER KIT
WHO ANSWERED FIRST? FIND OUT WITH THIS QUIZ BUZZER KIT BUILD INSTRUCTIONS Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit Board (PCB).
More informationSoldering Techniques N I A G A R A C O L L E G E T E C H N O L O G Y D E P T.
Soldering Techniques N I A G A R A C O L L E G E T E C H N O L O G Y D E P T. Soldering 101 Soldering is the process of joining two metals together to form an electrically and mechanically secure bond
More informationAdafruit Proto Shield for Arduino
Adafruit Proto Shield for Arduino Created by lady ada Last updated on 2016-08-04 11:06:30 PM UTC Guide Contents Guide Contents Overview Make it! Lets go! Preparation Prep Tools Parts list Parts List Optional
More informationWhat is a multimeter?
What is a multimeter? A multimeter is a devise used to measure voltage, resistance and current in electronics & electrical equipment It is also used to test continuity between to 2 points to verify if
More informationBUILDING INSTRUCTIONS
etap2hw 38 mm I2C to LCD Interface BUILDING INSTRUCTIONS October 2013 P. Verbruggen Rev 1.01 15-Oct-13 Page 1 Table of Contents Chapter 1 General Information 1.1 ESD Precautions 1.2 Further Supplies 1.3
More informationModular I/O System Analog and Digital Interface Modules
OPERATING INSTRUCTIONS Modular I/O System Analog and Digital Interface Modules Installation Operation Maintenance Document Information Document ID Title: Operating Instructions Modular I/O System Part
More informationAnalog Electronics I. Laboratory
Analog Electronics I Laboratory Exercise 1 DC Power Supply Circuits Aim of the exercise The aim of this laboratory exercise is to become familiar with rectifying circuits and voltage stabilization techniques
More informationRS232/DB9 An RS232 to TTL Level Converter
RS232/DB9 An RS232 to TTL Level Converter The RS232/DB9 is designed to convert TTL level signals into RS232 level signals. This cable allows you to connect a TTL level device, such as the serial port on
More informationK8022. Passive Preamp with RF remote control
Total solder points: 220+ 65 Difficulty level: beginner 1 2 3 4 5 advanced Passive Preamp with RF remote control Two stereo line level RCA inputs One stereo RCA output to power amp Motor controlled volume
More informationLAB 1 TECHNICAL DOC 3 IN ONE LAB DEVICE. Velleman Legen Heirweg 33 9890 Gavere Belgium
LAB 1 TECHNICAL DOC 3 IN ONE LAB DEVICE Velleman Legen Heirweg 33 9890 Gavere Belgium SPECIFICATIONS DIGITAL MULTIMETER 3 1/2 backlit LCD Automatic polarity indication DC voltage 200mV to 600V in 5 steps
More informationThe Radio-Kits Digital SWR meter kit Construction and user manual
The Radio-Kits Digital SWR meter kit Construction and user manual Author - Steve Drury G6ALU List of contents Section Page no. 1. Features and specifications 2 2. Introduction 2. Construction 4. General
More informationElectronics. Discrete assembly of an operational amplifier as a transistor circuit. LD Physics Leaflets P4.2.1.1
Electronics Operational Amplifier Internal design of an operational amplifier LD Physics Leaflets Discrete assembly of an operational amplifier as a transistor circuit P4.2.1.1 Objects of the experiment
More informationTHE ELECTRONIC DICE. a technology project for secondary education. Name: Class:
THE ELECTRONIC DICE a technology project for secondary education Name: Class: Many parties were involved in making this lesson / project available for schools: This technology project was originally developed
More informationTEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE GET IN TUNE WITH THIS FM RADIO KIT. Version 2.
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE GET IN TUNE WITH THIS FM RADIO KIT Version 2.0 Index of Sheets TEACHING RESOURCES Index of Sheets
More informationABB Drives. User s Manual HTL Encoder Interface FEN-31
ABB Drives User s Manual HTL Encoder Interface FEN-31 HTL Encoder Interface FEN-31 User s Manual 3AUA0000031044 Rev B EN EFFECTIVE: 2010-04-06 2010 ABB Oy. All Rights Reserved. 5 Safety instructions
More informationProgrammable Single-/Dual-/Triple- Tone Gong SAE 800
Programmable Single-/Dual-/Triple- Tone Gong Preliminary Data SAE 800 Bipolar IC Features Supply voltage range 2.8 V to 18 V Few external components (no electrolytic capacitor) 1 tone, 2 tones, 3 tones
More informationDashboard Digital Voltmeter
Dashboard Digital Voltmeter...November, 2002 This project is helpful to anyone who drives an automobile. I had found this project at the local libary... in an old publication. I made it and it worked fine.
More informationAP Physics Electricity and Magnetism #4 Electrical Circuits, Kirchoff s Rules
Name Period AP Physics Electricity and Magnetism #4 Electrical Circuits, Kirchoff s Rules Dr. Campbell 1. Four 240 Ω light bulbs are connected in series. What is the total resistance of the circuit? What
More informationBMD16N-SD. version 1.2
BMD16NSD version 1.2 Feedback decoder with 16 contacts with integrated current detection for the S88bus Compatible with a.o. Märklin Digital, Uhlenbrock Intellibox, Fleischmann TwinCenter and LDT HSI88
More informationAnalog control unit for mobile robots
Analog control unit for mobile robots Soldering kit for experimentation For Fischertechnik robots and others Most diverse functions Requires no programming Patented sensor technology Summary We are pleased
More informationCombi B Alarm box. Mounting instructions
Combi B Alarm box Mounting instructions EN Mounting instructions Alarm box Combi B VdS, G113064, G113065, G113066 Table of Contents 1 Description... 3 2 System overview... 3 3 Structure... 3 3.1 Power
More informationINTERNATIONAL ATOMIC ENERGY AGENCY INSTRUMENTATION UNIT SMD (SURFACE MOUNTED DEVICES) REPAIR S. WIERZBINSKI FEBRUARY 1999
(SURFACE MOUNTED DEVICES) REPAIR S. WIERZBINSKI FEBRUARY 1999 (SURFACE MOUNTED DEVICES) REPAIR 1 TABLE OF CONTENTS PAGE 1. INTRODUCTION 3 2. ADVANTAGES 4 3. LIMITATIONS 4 4. DIALECT 5 5. SIZES AND DIMENSIONS
More informationThe $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit.
The $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit. Micro Wizard has been manufacturing Pinewood Derby timers for over 10 years.
More informationTROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE LESTRONIC II BATTERY CHARGER FOR MOTIVE POWER BATTERIES PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment, it is important to read
More informationKit 27. 1W TDA7052 POWER AMPLIFIER
Kit 27. 1W TDA7052 POWER AMPLIFIER This is a 1 watt mono amplifier Kit module using the TDA7052 from Philips. (Note, no suffix.) It is designed to be used as a building block in other projects where a
More informationCornerstone Electronics Technology and Robotics I Week 15 Voltage Comparators Tutorial
Cornerstone Electronics Technology and Robotics I Week 15 Voltage Comparators Tutorial Administration: o Prayer Robot Building for Beginners, Chapter 15, Voltage Comparators: o Review of Sandwich s Circuit:
More informationPololu DRV8835 Dual Motor Driver Shield for Arduino
Pololu DRV8835 Dual Motor Driver Shield for Arduino Pololu DRV8835 Dual Motor Driver Shield for Arduino, bottom view with dimensions. Overview This motor driver shield and its corresponding Arduino library
More informationAutoRanging Digital MultiMeter
Owner's Manual AutoRanging Digital MultiMeter Model No. 82139 CAUTION: Read, understand and follow Safety Rules and Operating Instructions in this manual before using this product. Safety Operation Maintenance
More informationCell Phone Charging Purse
Cell Phone Charging Purse Created by Becky Stern Last updated on 2015-02-20 01:00:16 PM EST Guide Contents Guide Contents Overview Prepare USB and Power Supply Create a Charging Shelf Install Coil in Bag
More informationInstallation manual. Version 1.1. www.videx-security.com
Installation manual Version 1.1 www.videx-security.com 2 Table of Contents MANUAL INTRODUCTION... 4 SYSTEM INTRODUCTION... 4 SYSTEM COMPONENTS... 5 CONTROLS... 6 3.5A 13.8Vdc PSU... 6 CONTROL PCB... 6
More informationWD7S PRODUCTIONS HIGH VOLTAGE POWER SUPPLY BOARD HV-2
HIGH VOLTAGE POWER SUPPLY BOARD WARNING WARNING WARNING THIS POWER SUPPLY USES LETHAL VOLTAGES THIS IS NOT A BEGINNERS PROJECT!! IF YOU HAVE NEVER WORKED WITH HIGH VOLTAGE BEFORE, SEEK ANOTHER S ADVICE
More information7 FUNCTION DIGITAL MULTIMETER
7 FUNCTION DIGITAL MULTIMETER 90899 OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight Tools. All rights
More informationwww.rkeducation.co.uk solutions for teaching and learning
Teacher Notes Transistor Astable Project Introduction The aim of this 7 week (2hr lessons) project is to design and manufacture an electronic product based on the transistor astable circuit. The project
More informationATL Fuel Level Sender Probes
T E C H N I C A L S P E C I F I C A T I O N The ATL EL-AD-151 (Resistance Output) and EL-AD-152 (Voltage Output) Fuel Level Senders are highly advanced sensors for continuously measuring the contents of
More informationHow to connect to a Class II router using a mobile-phone data cable specifically for Solwise & Safecom routers
USB to router s serial port How to connect to a Class II router using a mobile-phone data cable specifically for Solwise & Safecom routers by Neo at RouterTech.Org Introduction Routers based on the AR7RD/AR7WRD
More informationDC Circuits (Combination of resistances)
Name: Partner: Partner: Partner: DC Circuits (Combination of resistances) EQUIPMENT NEEDED: Circuits Experiment Board One Dcell Battery Wire leads Multimeter 100, 330, 1k resistors Purpose The purpose
More informationINTELLIGENT LEAD ACID BATTERY CHARGER
Total solder points: 150 Skill level : Beginner 1 2 3 4 5 Advanced INTELLIGENT LEAD ID BATTERY CHARGER Features: Suitable for 6V and 12V sealed and open leadacid batteries Fully automatic charge and maintenance
More informationCPL SYSTEMS / GROENEVELD AUTOMATIC GREASING SYSTEM COMPLETE SYSTEM CHECK PNEUMATIC PUMP
CPL SYSTEMS / GROENEVELD AUTOMATIC GREASING SYSTEM COMPLETE SYSTEM CHECK PNEUMATIC PUMP Feb 5, 2003 1 CPL SYSTEMS / GROENEVELD AUTOMATIC GREASING COMPLETE SYSTEM CHECK - PNEUMATIC PUMP THE SYSTEM DOES
More informationContents. Document information
User Manual Contents Document information... 2 Introduction... 3 Warnings... 3 Manufacturer... 3 Description... Installation... Configuration... Troubleshooting...11 Technical data...12 Device Scope: PCB
More informationAssembly Notes. Disclaimer:
Assembly Notes Before you start building your kit, please take time to read the manual in full at least once to enable you to fully understand the procedures and avoid any mistakes. The following notes
More informationTutorials Drawing a 555 timer circuit
Step 1 of 10: Introduction This tutorial shows you how to make an electronic circuit using Livewire and PCB Wizard 3. You should follow this tutorial to learn the basic skills you will need to use Livewire
More information