Wheels, Tires, & Brakes

Transcription

1 Wheels, Tires, & Brakes Proudly Distributed By

2 Dual Flange Wheel Assemblies Chrome or polished stainless steel spokes are laced to chrome rims and hubs. The 16" wheel assemblies feature our Europeanmanufactured chrome 16" rims. The hubs feature thicker spoke flanges, and rotor flanges held to.001" runout with either 5/16" or 7/16" holes on both sides. All hubs accept any stock sprocket/rotor or rotor/rotor combination for greater flexibility when building custom wheel combinations. They include all internal spacers, seals and washers, and bearing end play is set at the factory. Wheel assemblies will bolt-on to most models from Note: Wheels fit the rear of most models from when installed with a CC #19722 spacer (OEM ) between the belt pulley or sprocket and the hub. Wheels with 7/16" Flange Holes " x 3.00" with stainless steel spokes $ Wheels with 5/16" Flange Holes " x 3.00" with stainless steel spokes $ " x 2.15" with stainless steel spokes $ Front Axle Spacer for FXWG Models Replacement right or left axle spacers for FXWG models. May also be used when fitting other wheels (such as CC # s or 19694) to late model front ends.sold in packs of left spacer (repl. OEM ) $ right spacer (repl. OEM ) $3.50 Chrome Dual Flange Wheel Hubs Complete chrome hub assemblies for the front or rear of most Harley- Davidson models from /16" or 5/16" holes in both flanges, all internal components and bearing preload set at the factory Front or rear hub with 7/16" holes in both flanges for models from (repl. OEM A) $ Rear hub with 7/16" Pulley /Sprocket side flange holes & 3/8" Brake Rotor side flange holes for models from (repl. OEM ) $ Front hub with 5/16" holes in both flanges (repl. OEM A) $ Rebuild kit (includes bearings, cones, seals, spacers, washers and retaining rings) $ Timken bearing and cone (repl. OEM 9052) $ Bearing only $ Cone only $ Outer bearing spacers (repl. OEM ) sold in pairs..$ Rubber oil seals (repl. OEM ) pack of $ Rubber oil seal (repl. OEM A) pack of $ Hub washers (repl. OEM ) sold in pairs $ Hub retainer rings (repl. OEM 11027) sold in pairs $ Spacer 4.420" (repl. OEM ) Orange $ Spacer 4.434" (repl. OEM ) Yellow $ Spacer 4.448" (repl. OEM ) White $7.99 Belt Pulley and Sprocket Spacer This part was used on many Big Twin models from It was most commonly used on belt drive models to achieve the proper spacing of the rear belt pulley to the wheel. This spacer is required for use on our rear wheels when used in many different applications. Fits Big Twin and Sportster models Replaces OEM $10.49 U.S. Patent #4,880, Wheels with Timken-Style Star Hubs for Big Twins A wide selection of stock replacement and custom wheels with chrome or polished stainless steel spokes laced to our patented Star Hub with Timken-style bearings (CC #64012). Bearing preloads are set at the factory. These complete wheel assemblies fit the front or rear of most Big Twin models from when the appropriate Custom Chrome Axle and Hardware kit is used. The stock brake axle sleeve for the appropriate application is also required. Though the Axle Kits will work with Original Equipment Star Hubs, the Original Equipment axles will not work with Custom Chrome Wheel Assemblies with Star Hubs. Complete Wheel Assemblies " x 3.00" with stainless steel spokes $ " x 2.15" with stainless steel spokes $ Star Hub with Timken-Style Bearings Complete Star Hub assembly $ Axle and Hardware Kits Front for models from $ Front for models from $ Rear for models from $ Rear for models from $39.99 Replacement Spokes " spoke set. Chrome $ " spoke set. Stainless steel $ " spoke set. Chrome $ " spoke set. Stainless steel $ " spoke set Chrome $ " spoke set Stainless steel $ *New style lacing pattern. Replacement Parts Bearing spacer (2.410" orange) sold each $ Bearing spacer (2.424" yellow) sold each $ Bearing and race (two complete sets) $ Bearing only (pair) $ Steel oil seal (1.625" O.D.) pair $ Chrome axle spacer (sold each) $ Retaining ring (pair) $ Outer cover without hole for zerk fitting (repl. OEM TA) $ Hub cover screw/lockwasher kit (pack of 5) $4.99 TRAN.02 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.

3 Front Wheel Assemblies for Sportster, Dyna Glide, FX and FXR Models from Stock replacement and custom wheels with chrome or polished stainless steel spokes laced to a chrome hub and a 19" or 21" drop center rim with rolled edge. Wheel assemblies are available for most models from All wheel assemblies are complete with axle spacer, seals and bearings which have had their preload set at the factory. For all Sportster, FX and FXR models with dual disc narrowglide front ends from " x 2.50" with stainless steel spokes $ " x 2.15" with stainless steel spokes $ For all Sportster, Dyna Glide, FX and FXR models with single or dual disc narrowglide front ends from " x 2.50" with stainless steel spokes $ " x 2.15" with stainless steel spokes $ Chrome Front Hubs Include the chrome hub and all of its internal components with properly spaced bearings. For all Sportster, FX and FXR models with dual disc narrowglide front ends from Complete hub assembly (repl. OEM ) $ Left bearing spacer (repl. OEM ) $ Spacer 2.564" (violet) replaces OEM $ Spacer 2.550" (pink) replaces OEM $ Spacer 2.536" (gold) replaces OEM $ Rebuild kit (includes bearings, cones, seals, and left-hand spacer) $ Steel oil seal (repl. OEM ) pack of $ Rubber oil seal (repl. OEM A) pack of $ Timken bearing and cone (repl. OEM 9052) $9.99 *Note: Modifications to caliper pin and additional rotor spacers may be required for clearance. For Sportster, Dyna Glide, FX and FXR models (except FXLR) with single or dual disc narrowglide front ends from Complete hub assembly (repl. OEM ) $ Right bearing spacer (repl. OEM ) $ Spacer 2.564" (violet) replaces OEM $ Spacer 2.550" (pink) replaces OEM $ Spacer 2.536" (gold) replaces OEM $ Steel oil seal (repl. OEM ) pack of $ Rubber oil seal (repl. OEM A) pack of $ Timken bearing and cone (repl. OEM 9052) $9.99 Front Wheel Assemblies for Sportster and FX Models from A selection of stock replacement and custom front wheels for all Sportster and FX models (except 77 FXS and XLCR) with single disc narrow glide front ends. Available with either chrome or polished stainless steel spokes laced to a chrome hub and a 19" or 21" Drop Center rim with rolled edge. Each wheel assembly is complete with axle spacer, seals and bearings with their preload set at the factory " x 2.50" with stainless steel spokes $ " x 2.15" with stainless steel spokes $ Chrome Front Hub Assembly for Models from A complete assembly including the chrome hub and all of its internal components with properly spaced bearings. Hub fits the front wheel on Sportster and FX models from (except 77 FXS and XLCR) Complete hub assembly (repl. OEM ) $ " center bearing spacer (repl. OEM ).... $ Left bearing spacer (repl. OEM ) $ Rebuild kit (includes bearings, cones, seals, and left-hand spacer) $ Steel oil seal (repl. OEM ) pack of $ Timken bearing and cone (repl. OEM 9052) $9.99 Chrome Rear Hub AssemblyRear Wheel Assemblies for Big Twins from Complete wheel hub assembly includes the chrome hub and all of its internal components with properly spaced bearings. The hub fits the front or rear wheel of all FL models from and the rear of FX models from Complete hub assembly (repl. OEM A) $ Bearing spacer (repl. OEM ) $ Bearing locknut (repl. OEM ) $ Hub spacer (repl. OEM ) $ Rubber oil seal (repl. OEM ) Sold in packs of $ Hub bearing (repl. OEM ) $ TRAN.03

4 Spoke Extra-Wide Offset Dual Flange Rear Hubs Pulley side is offset.875" further out than standard style hubs. Eliminates the need for pulley spacers on most applications, and places the bearings farther apart for greater stability. Helps to eliminate bent axles often associated with using standard hubs for wide applications using large pulley spacers Sold each $ " Drop Center Rim 3"-wide drop-center rim to fit 5.00/5.10 x 16" motorcycle tires Chrome 40-hole rim (repl. OEM A) $ Black 40-hole rim (repl. OEM A) $ Custom Chrome Rims These 40-hole drop center rims are formed from a high-strength steel alloy and given a coating of show-quality chrome that will stay looking great for years. They re the finest stock replacement rims available anywhere. Lace them with our twisted spokes for a truly custom look! " x 3.00" for use with steel hubs used from (replaces OEM )MCV $ " x 5.75" for custom applications $ Note: The CC # " x 3.00" rim requires the use of a metal center valve tube (CC # ). Chrome Front Rims 19" Rim Exclusive to Custom Chrome. This show-chromed 19" x 2.50" Rolled- Edge drop center rim is styled like the classic drop center, and the rolled edge gives your front wheel additional strength. Another first for this rim is the duplication of the OEM spoke dimple pattern which permits effortless lacing to disc wheel hubs Replaces OEM $ " Rim This show chrome drop center rim with a fully-rolled edge is the same size (21" x 2.15") and has the same spoke pattern as the Original Equipment 21" rim Replaces OEM B $95.99 TRAN.04 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.

5 08250 Custom Chrome Spoke Sets Custom Chrome s spoke sets use nothing but the best 6/8 gauge carbon and polished stainless steel materials, but we ve put a new twist on them for a great custom look. Flat spokes are our regular spokes with the body rolled for a flattened profile. Add a few twists for the great-looking twisted sets that create wheels that throw light in all directions in a kaleidoscope of colors and highlights. Flat, twisted and regular round spokes come in polished stainless steel and chrome-plated carbon steel sets. Tips On Choosing Spokes On the following pages are the variety of stock and custom rims and hubs available from Custom Chrome or Harley-Davidson. Use the illustrations to determine hub and rim combination, then select the spoke set to complete your wheel. For example: an aluminum front hub for FX models laced with Twisted stainless steel spokes to a chrome 21" Akront drop center aluminum rim for an FXWG (shown in illustration J ), uses CC #08215 spoke set. The rim illustration guide shows basic rim shape, and position of the spoke holes in relation to each other. This should help identify the rim you have or want to buy Replacement Spoke Nipples (6mm Square) Set of chrome nipples (42) extralong $ Set of stainless steel nipples (42) extra-long $ Set of chrome nipples (42) stocklength $ Set of stainless steel nipples (42) stock-length $0.74 Easy Reference Spoke Chart Replacement Spokes with Nipples for Most Stock-Style 40-Spoke Wire Wheels For Steel Dual or Single Flange Front or Rear Hubs: " spoke set. Chrome $ " spoke set. Stainless steel $ Twisted spoke set. Chrome $ Twisted spoke set. Stainless steel $ " spoke set Chrome $ " spoke set Stainless steel $ Twisted spoke set. Chrome $ Twisted spoke set. Stainless steel $ " spoke set. Chrome $ " spoke set. Stainless steel.. $ Twisted spoke set. Chrome $ Twisted spoke set. Stainless steel $ For Aluminum Front Hubs* : " spoke set Chrome* $ " spoke set Stainless steel*.. $ Twisted spoke set. Chrome* $ " spoke set. Chrome* $ " spoke set. Stainless steel* $ Twisted spoke set. Chrome $99.99 Part #19544 Hub Spokes for Sportster Models with Rear Spool Hub When used with any of the six spoke sets listed below, this rear hub will fit any Sportster or K model (except XLCR) from For all steel 15" drop center rims (rim illustration E ) Chrome Price Stainless Price $ $ Round spoke set For all steel 16" drop center rims (rim illustration E ) Chrome Price Stainless Price $ $ " spoke set. Chrome Fits all steel 18" drop center rims (rim illustration E ) Chrome Price Stainless Price $ $ Round spoke set Spokes for Sportster and FX Models with Front Drum Hub For Sportster or FX models from Fit OEM steel 19" drop center rims (rim illustration H ) Chrome Price Stainless Price $ $ Round spoke set Fit all steel 19" custom rims (rim illustration F ) and 19" Akront aluminum rims Chrome Price $46.99 Round spoke set Fit all steel 21" custom and drop center rims (rim illustrations F and J ) and 21"Akront aluminum rims Chrome Price $42.99 Round spoke set Rim Illustrations Illustration E Illustration F Illustration G Illustration H Illustration J TRAN.05

6 Late Model Wheel Hub Spacers and Bearing Shims These parts are accurate reproductions of the Original Equipment pieces used on 5-speed Dresser models from 82-99, and most other models from Installing them in your wheels will permit you to set your wheel bearing end play tighter, resulting in improved rideability with better cornering and less straight-line weaving. Hub Spacers Sold each " spacer for narrow hub (repl. OEM ) $ " spacer for wide hub (repl. OEM ) $ Wheel bearing spacer washer (repl. OEM ) $4.99 Wheel Bearing Shims Sold in packs of " shim (repl. OEM ) $ " shim (repl. OEM ) $ " shim (repl. OEM ) $ " shim (repl. OEM ) $ " shim (repl. OEM ) $ Wheel Bearing Spacers Just what you need to redo the bearings on your hub. Available in different lengths. Sold each. Steel Dual Flange Hub Spacers Spacer 4.420" (repl. OEM ) Orange $ Spacer 4.434" (repl. OEM ) Yellow $ Spacer 4.448" (repl. OEM ) White $7.99 Cast Wheel Hub Spacers " (repl. OEM ) red $ " (repl. OEM ) yellow $ " (repl. OEM ) white $7.99 Aluminum Front Hub Spacers " (repl. OEM ) gold and violet $ " (repl. OEM ) red and white $ " center bearing spacer (repl. OEM ) $ " (repl. OEM ) green and orange $ Spacer 2.536" (gold) replaces OEM $ Spacer 2.550" (pink) replaces OEM $ Spacer 2.564" (violet) replaces OEM $ Wheel Seals Fits the spoked rear wheels on Sportster and K models; FLs and FXs Rubber oil seal (repl. OEM ) Sold in packs of 10...$ Steel oil seal (repl. OEM ) Sold in packs of $1.20 Fits the spoked rear wheel on FLs, FXs and FXRs from and XLs from 79-83; spoked front on FLs and FXWGs 80-83; cast front or rear on FLs 80-84; cast front or rear (brake side only) on FLTs and FLHTs from Also fits the swingarm on all Big Twin drum brake models from Rubber oil seals (repl. OEM ) pack of $1.30 Fits the cast rear and spoked or cast front wheels on FXs (except FXWG), FXRs and XLs from 73-83; cast front and rear wheels on FLs from 73-79; cast rear wheel (sprocket side only) on FLT/FLHT from Also fits the swingarm on 4-speed FX Big Twin disc brake models from Steel oil seal (repl. OEM ) pack of $1.10 Fits the cast or spoked front and rear wheels on most models from Rubber oil seal (repl. OEM A) pack of $ Wheel Hub Rebuilding Kits Contains all of the necessary bearings, seals and spacers to rebuild either cast wheels or aluminum front hubs. Fit Sportster, FX and FXR models from 73-83, or the steel dual-flange wheels on most models from Aluminum hubs and front mag wheels $ Steel dual-flange hubs $29.99 TRAN.06 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.

7 Original Equipment-Style Star Hub Replacement Parts Thrust bearing sleeve (repl. OEM ) $ Thick thrust washers (repl. OEM ) 5 pair $ Adjusting shims (.002") repl. OEM (pack of 50) $ Retainer and rollers (repl. OEMs , 9220A) $ Inner thrust washer (repl. OEM ) pack of $ Bearing collar (repl. OEM ) $ Roller bearing sleeve (repl. OEM ) $ Brake side retainer and rollers (repl. OEMs , 9220A) $ Brake side thrust washers (repl. OEM ) pack of $ Thrust washer lockring (repl. OEM ) 5 pair $ Brake side cork washer retainers (repl. OEM ) pack of $ Small cork washer (repl. OEM ) pack of $ Gasket and cork washer kit (repl. OEMs , , ) $ Large brake side cork washers (repl. OEM ) pack of $ Outer cover without hole for zerk fitting (repl. OEM TA) $ Hub cover screw/lockwasher kit (pack of 5) $4.99 6"-Long Stainless Steel Wheel Spacer Stock Make your own custom wheel spacers! Stainless steel is rust free! No chrome plating required as with spacers machined from plain steel. Simply cut-to-length and use! Fits many 3/4"-diameter axle applications (6"-long x 3/4" ID x 1 1/8" OD) $36.99 Star Hub Cover Kit Includes the chrome outer cover, inner cover with grease fitting, gasket and corks, screws and lockwashers Fits Star Hubs from $ Axle Sleeves for Star Hubs Front axle sleeve (brake side) for Big Twins from (repl. OEM ) $ Left rear axle sleeve for Big Twins from (repl. OEM )... $ Hub Rebuild Kits Hub rebuild kits for most Big Twin and Sportster models with steel or aluminum hubs. Available with or without bearings, these kits include seals, bearing spacers, center spacers (between bearings) snap rings, washers and gaskets necessary to rebuild the specific hubs listed. Note: Kits do not contain outer axle spacers. With Bearings Price Without Bearings Fits dual flange hubs front and rear on FL models 73-83, front FXWG and rear FX models Contains 4.434" (yellow) center spacer Price $ $ TRAN.07

8 I H G F K A Chrome-Plated Front Axles The greatest selection of chrome axles in the industry. Complete assemblies for models as far back as 36. Fully-chromed, including the hardware. Axle shafts are machined from heat-treated chrome moly steel, triple-step chrome-plated, then machine-polished and ground to a finish size tolerance of ±.0005". Axles are available individually or packaged complete with a fully-chromed hardware kit. Photo shows contents of hardware and axle kits as well as the basic axle profile. ILLUS APPLICATION Replaces Axle OEM# Axle Only Price Hardware Only Price Hardware & Axle Kit A Fits EL, FL and UL from $ $ $46.99 B Fits FL models from $ $ $32.99 C Fits EL and FL from $ $ $39.99 D Fits 4-speed FL models from 73-80, and FXWG from $ $ $32.99 E Fits FL 81-84; FXST, FXSTC, and FXDWG 84; FXWG 84-86; FLT, FLHT, FLHS models $ $ $35.99 F Fits Sportster, FX and K models from $29.99 n/a $28.99 G Fits Sportster and FX models with single disc brake from n/a $ $31.99 H Fits Sportster, FX and FXR models with dual disc $ $9.99 brake from $31.99 I Fits Sportster, FX and FXR models with 35mm forks from $ $ $30.99 K Fits FL Softail models A $ $ $50.99 E D C B Price TRAN.08 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.

9 D E F G H A B C Chrome-Plated Rear Axles The greatest selection of chrome axles in the industry. Complete assemblies for models as far back as 36. Fully-chromed, including the hardware. Axle shafts are machined from heat-treated chromemoly steel, triple-step chrome-plated, then machine-polished and ground to a finish size tolerance of ±.0005". The rear axle nuts are attached to the shaft with a full-penetration weld, then machined smooth before final machine-polishing and plating. Axles are available individually or packaged complete with a fully-chromed hardware kit. Photo shows contents of hardware and axle kits as well as the basic axle profile. ILLUS.. APPLICATION Replaces Axle OEM# Axle Only Price Hardware Only Price Hardware & Axle Kit A Fits EL, FL and UL from $ $ $49.99 B Fits FL models from A $ $ $39.99 C Fits FL and FX models from $ $ $41.99 D Fits 4-speed FL and FX models with rear chain drive from $ $ $35.99 E Fits 4-speed FL and FX models with rear belt drive from $ $ $33.99 F Fits Sportster and K models from 52-E $ $ $35.99 G Fits Sportster models from A $ $ $46.99 H Fits all FXR models from A $ $ $42.99 H Fits all Softail models from A $ $ $39.99 H Fits all FLT/FLHT/FLHS/FLHR models from A $29.99 n/a n/a Price TRAN.09

10 CC Pyramid Axle Adjusters Forged steel axle carriers are machined to close tolerances to be a snug fit inside the swingarm section eliminating the common problem of swingarm distortion when axle nuts are overtightened. The chrome end caps are made of diecast aluminum and the chrome-steel nuts have a long shank tapped to permit a full range of axle adjustment. They fit all CC chrome 4-speed swingarms as well as the stock swingarms on Sportster models from and speed FL and FX models. They also fit 86 Softail models. Include instructions. Sold in pairs Replaces OEM T $49.99 Chrome Axle Adjuster End Caps Add a beautiful chrome-plated highlight to the ends of your swingarm. Die-cast construction won t distort like the Original Equipment stamped steel plates. Work with your stock axle carriers and increase the range of adjustment. Fit 4-speed Big Twins from and Sportster models from Sold in pairs $ Chrome Rear Wheel Adjusters Choose the rear wheel adjuster for your motorcycle from the selection below. Each kit comes complete and is beautifully chromeplated.sold in pairs Fit Sportster and K models from (repl. OEM T) $ Fit Big Twin models from (repl. OEMs , 7800W) $ Fit all Big Twin models (except Dyna Glide and Softail models) from and Sportster models from (repl. OEM T) $16.99 Tire Tubes and Rim Strips A wide section of sizes from quality manufacturers Extra-Wide Inner Tubes The solution for extra-wide tires that require tubes. Butyl rubber construction for good air retention, carefully molded for uniformity. Center valve stem /60 x 16" for use with 180 x 16" and 200 x 16" extra-wide tires $ /55 x 18" for use with 170 x 18", 180 x 18" and 200 x 18" extra-wide tires $ /55 x 17 for use with 200 x 17 wide tires $37.99 Imported Tubes /90 x 15" Metal Center Valve $ /90 x 16" Metal Center Valve $ "-5.10" x 16" Rubber Side Valve $ "-5.10" x 16" Metal Side Valve $ /90 x 17" Metal Side Valve $ /90 x 18" Metal Center Valve $ "-3.00" x 19" Metal Center Valve $ "-3.50" x 19" Rubber Center Valve $ "-3.00" x 21" Metal Center Valve $ "-3.50" x 21" Metal Center Valve $16.49 Extra-Wide Rim Strips " center valve (3.1"- wide) $ " center valve (2"-wide) $2.99 Rim Strips " side valve $ " center valve $ " center valve $ " center valve $ " center valve $1.49 TRAN.10 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.

11 Speedmaster MK2 AM6 Long lasting, positive steering tire for front wheel fitment only. S Rated for speeds up to 112 mph. Ribbed pattern for classic look. Unique for long life and even wear. Manufactured from a cling rubber. Excellent lateral stability and high mileage. Speedmaster Bias (TT) "-19" Blackwall $ "-19" Blackwall $ "-21" Blackwall $ SM MK II AM7 The high mileage, high profile tire for rear fitment. Perfect for Harley riders or those seeking traditionally styled tires. S Rated for speeds up to 112 mph. Center rib, flanked by interlocking studs. Cling rubber compound for excellent wet road adhesion. SM MK II AM7 Bias (TT) " -16" $ Gangster The Gangster has all the features of Avon s popular Universal, with the added look of a 2 3/4 wide, white sidewall. A perfect tire for classics and restorations, the Gangster features state-of-the-art rubber compound, blending performance and vintage style. Tubeless construction. Front and rear application. Gangster Bias (TL) MT90H-16" Wide Whitewall $ MOTORCYCLE TIRE SIZE CONVERSION CHART FRONT TIRES METRIC ALPHA INCH 80/90 MH / /90 MJ / /90 MM / /90 MN / / / /90 MR / /90 MT /5.10 REAR TIRES METRIC ALPHA INCH 110/90 MP / /90 MR / / / /90 MT / / / /85 MU / /90 MU / /80 MV / /90 MV / TRAN.11

12 Rear Brake Caliper Kit This kit includes a CC #13012 deluxe chrome single action rear brake caliper, complete with brake pads, mounting bolts, bleeder valve and all internal components " disc brake kit $ Ferodo 'P compound pad $ Motor Factory Organic pad set $ Brake MAX pad set $11.99 Rear Brake Calipers Precision-engineered calipers are made of die-cast aluminum that is polished and then chrome-plated or painted wrinkle black. Perfect replacements for the stock unit on Softail, FXR, Sportster, and Dyna Glide models from late (replaces OEM ) Chrome $ Black wrinkle $ Ferodo 'P compound pad set $ Motor Factory Organic pad set $ Complete kit Rear Brake Caliper Assemblies Chrome-plated, or durable powder-coated replacement rear brake calipers for 4-speed Big Twin models from Compatible with either the boomerang support bracket (used as Original Equipment thru 80), or the later Y bracket used from Complete with late model square section O-rings and seals, and mounting bushings and pins. Completely rebuildable with Original Equipment or CC parts Chrome $ Gloss black powder coat $ Ferodo 'P compound pad $ Motor Factory Organic pad set $ Brake MAX pad set $11.99 Rear Brake Rebuild Kit This kit contains all the parts necessary to repair worn, rattling banana style rear calipers on FL and FX models Complete as shown, including an oversized pin to repair badly worn (oval) caliper through holes Complete kit (includes hardware kit) $ Mounting kit. Fits FL and FX models $ Chrome steel brake anchor. Replaces OEM T....$ Mounting bracket only (Includes bushings). Replaces OEM $ Brake MAX pad set $11.99 Disc Rotor Spacer.040"-thick spacer is used to re-establish correct rotor-to-caliper alignment and spacing whenever servicing wheels, brake calipers, supports or rotors on Original Equipment disc brake systems from Sold each Replaces OEM $6.99 TRAN.12 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.

13 Caliper Mounting Stud and Pin Kit Includes brake pad pins, mounting bracket steel pin bushings, mounting stud, locknut and washer for OEM and CC banana calipers from Complete kit (repl. OEM ) sold each $ Pins only (repl. OEM ) card of 5 pairs $ Large steel pin bushing (repl. OEM ) sold each $ Small steel pin bushing (repl. OEM ) sold each $2.99 Heavy-Duty Rear Caliper Support Spring Reduces rear caliper rattle and mounting pin wear on boomerang supported, Big Twin rear brake calipers from Chromed bracket fits easily over the axle so the chromed support spring places steady upward pressure against the caliper Sold each $8.99 Standard Caliper Support Complete with bracket, spring and button. Fits all rear banana calipers from Sold each $11.99 Dual Disc Caliper Bolt Kit Contains 4 chrome sockethead shoulder bolts and nuts. Designed to mount the front dual disc brake calipers on FX, FXR, FXWG and XL models Set of Replaces OEMs , $ Caliper Mounting Bushings This set of American-made caliper mounting bushings will fit all dual disc fork legs from Set of two Replaces OEMs , $ Caliper Mounting Y Brackets For 10" Rotor Systems Patterned after the later 11 1/2" caliper support used from 81-83, these unique brackets provide improved support and alignment for 10" rotor systems. Fit all Big Twin rear discs from Chrome $ Rear Brake Caliper Anchor Kit Includes the clevis pin, washer, and cotter pin. Fits all FXs from and 83 FXE (replaces OEMs 520W, 36718, and ) Bag of 5 kits $5.00 Brake Caliper Piston Assemblies Rear Fits FL and FX models from 73-E80 (repl. OEM ) $ Fits FL models from and FLT or FLHT models from (repl. OEM ) Includes boot and seal. Two required per caliper......$ Fits late 80 FL models, all FX models from late 80-82, and 83 FXE (repl. OEM ) $19.99 Front Fits FL models from (repl. OEM A) $ Fits FL models from late (repl. OEM ) $ Fits all single disc Sportster and FX models from (repl. OEM ) $ Fits all dual disc Sportster, FX and FXR models from Includes the piston, seal and rubber dust boot (repl. OEM ) $21.99 Caliper Mounting Pin Rebuild Kit Restores banana calipers to safe service when the caliper support pin has enlarged and egg-shaped the thru-hole in the caliper body. Kit includes a 3" support shaft, hardened washers and two sockethead screws Fits all banana calipers $ Brake Fittings and Bleeder Screws Wheel Cylinder Swivel Fitting Fits all Big Twins from (repl. OEM ) sold each.. $19.99 Wheel Cylinder Bolt Fits all Big Twins from (repl. OEM ) sold each... $6.99 Bleeder Screws Fits the rear wheel cylinder on all FL and FX models from 58-72; the FL sidecar wheel cylinder from 58-E70; the pieshaped front caliper on all Sportster and FX models from 74-77; the banana caliper on the front and rear of all FL models from 72-79; the banana caliper on the front of 73 Sportster and FX models; the banana caliper on the rear of all FX models from Replaces OEM Bleeder screws (repl. OEM ) pack of $1.20 Fits the front calipers of all dual-disc FX, FXR and Sportster, models from and FLT/FLHT models from 80-83; the banana caliper and the dual piston caliper on the rear of all FL, FLT and FLHT models from 80-86; the banana caliper on the rear of all FX models from 78-83; the rear caliper of all Sportster models from 77-81; the Hayes rear brake caliper used from Replaces OEM Pack of $ Chrome-plated (sold each).. $5.99 Brake Caliper Bleeder Screw Repair Kit Has an oversize bleeder screw and seat for banana caliper or drum brak Complete kit $4.99 TRAN.13

14 Chrome Rear Brake Backing Plates These backing plates are accurate reproductions of the obsolete and difficultto-find Original Equipment parts. They fit all Big Twin models with hydraulic rear brakes from and come complete with brake shoe retaining clips as well as the necessary chrome mounting hardware models (replaces OEM ) $ Chrome backing plate. Fits Big Twin models Replaces OEM $79.99 Note: Although every effort has been made to produce a cosmetically perfect part, because of the complexities of polishing these backing plates prior to plating, the chrome may appear to be flawed in some small areas. Brake Linings Replacement brake shoe linings for Original Equipment drum brakes. Includes Rivets. Sold in pairs Fit the rear of Big Twins with 1 7/16"-wide linings(replaces OEM ) $ Brake linings with rivets. Fits Big Twin rear and sidecar 58-up. Replaces OEM Sold in pairs $ Brake linings with rivets. Fits Big Twin rear Replaces OEM Sold in pairs $ Brake shoe linings with rivets. Fits front on FL models and XL models Also fits rear on XL models Replaces OEM A. Sold in pairs $14.99 Accel Rear Brake Wheel Cylinders and Rebuild Kits Quality assemblies featuring precisionmachined rugged cast steel housings, heavy-duty rubber cups and seals, and a unique compression spring that eliminates cup extenders. Fits Big Twin rear brake models from Wheel Cylinder (repl. OEM )..$59.99 Rebuild Kits (repl. OEM )...$ Bleeder screws (repl. OEM ) pack of $1.20 Chrome Brake Drums with Sprockets Chrome brake drum with sprocket. Fits Big Twin models Replaces OEM * $ Brake drum with sprocket. Chrome. Fits Big Twin models Replaces OEM C* $ Brake drum with sprocket. Chrome. Fits Big Twin models Replaces OEM * $ Brake drum with sprocket. Chrome. Fits Big Twin models Replaces OEM * $ Fits Sportster models from (except XLCR) repl. OEM $ Brake Shoes Brake shoes with linings for models with Original Equipment drum brakes from Sold in pairs. Front Brake Shoes Fit Sportster and K models from and all Big Twins from (replaces OEM TB)...$36.99 Rear Brake Shoes Brake shoes. Fits Big Twin rear Replaces OEM Sold in pairs $ Brake shoes. Fits Big Twin rear and sidecar Replaces OEM A. Sold in pairs......$ Brake shoes. Fits Big Twin rear Replaces OEM Sold in pairs $ Fit Sportster and K models (except XLCR) from (replaces OEM TB) $36.99 TRAN.14 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.

15 WHEELS, TIRES & BRAKES Mechanical Brake Parts Hydraulic Brake Parts Listed below in CC part number order Brake linings with rivets. Fits Big Twin rear and sidecar 58-up. Replaces OEM Sold in pairs $ Brake linings with rivets. Fits Big Twin rear Replaces OEM Sold in pairs $ Chrome backing plate. Fits Big Twin models Replaces OEM $ Brake drum with sprocket. Chrome. Fits Big Twin models Replaces OEM C* $ Brake drum with sprocket. Chrome. Fits Big Twin models Replaces OEM * $ Brake drum with sprocket. Chrome. Fits Big Twin models Replaces OEM * $ Brake shoes. Fits Big Twin rear Replaces OEM Sold in pairs $ Brake shoes. Fits Big Twin rear and sidecar Replaces OEM A. Sold in pairs $ Chrome brake drum mounting bolts. Fits Big Twins Replaces OEM A. Sold in 5 pack $ Brass 2-piece rear wheel cylinder swivel fitting. Fits Big Twin models Replaces OEM $ Rear wheel cylinder bolt. Fits rear brake swivel on FL models Replaces OEM Sold each $ Copper crush washers. Fits rear brake swivel bolt on Big Twins Replaces OEM Sold in 10-packs $ Return spring, brake shoe upper. Fits Big Twins Replaces OEM Sold in 5-packs $ Return spring, brake shoe upper. Fits Big Twins Replaces OEM Sold in 5-packs $ Return spring, brake shoe lower. Fits Big Twins Replaces OEM Sold in 5-packs $ Bleeder valve, 1/4". Fits Big Twins Replaces OEM Sold in 10-packs $1.60 *Note: Chrome must be removed from inside drum before installation to prevent damage to linings. Listed below in CC part number order Chrome lever, brake cam. Fits Big Twin models Replaces OEM $ Chrome lever, single hole (left side). Fits Big Twin models Replaces OEM $ Chrome lever, double hole (right side). Fits Big Twin models Replaces OEM $ Brake shoes. Fits Big Twin rear Replaces OEM Sold in pairs $ Chrome brake drum with sprocket. Fits Big Twin models Replaces OEM * $ Chrome lever, brake cam. Fits XL models Replaces OEM $ Brake drum mounting bolts. Chrome. Fits Big Twin models Replaces OEM Sold in 5 pack $ Clevis, brake rod. Chrome. Fits Big Twin models Replaces OEM $9.99 *Note: Chrome must be removed from inside drum before installation to prevent damage to linings Front Drum Brake Parts (Left Side Brake) Listed below in CC part number order Brake shoe linings with rivets. Fits front on FL models and XL models Also fits rear on XL models Replaces OEM A. Sold in pairs $ Brake shoes. Fits front on FL models and XL models Also fits rear on XL models Replaces OEM TB. Sold in pairs $ Chrome brake drum. Fits FL models Replaces OEM * $ Chrome brake drum mounting bolts. Fits FL models Replaces OEM A. Sold in 5 pack $ Chrome brake drum. Fits FL models Replaces OEM * $ Chrome hand lever assembly. Fits brake side on FL, FX and XL models and clutch side on FL models (small cable hole) $ Chrome cable tube and fitting.14 long. Fits FL models Replaces OEM and $10.99 *Note: Chrome must be removed from inside the drum before installation to prevent damage to linings. w w w.cu sto m c h ro m e.co m TRAN.15

16 Chrome Brake Line Fittings These brake line fittings are used on handlebar mounted master cylinder and front or rear brake line tees. Fit many models from Sold in packs of Plug 1/8" NPT (repl. OEM ) $ Straight male 1/8" NPT to female 3/8"-24 inverted flare (repl. OEM ) $1.80 Rear Backing Plate Wheel Cylinder Swivel Fitting Brass fitting replaces the stock piece perfectly. For the rear brake on models from Sold each Replaces OEM $24.99 Master Cylinder and Tee Fitting This 90 right-angle fitting connects the front brake line to the handlebar master cylinder and brake tee. Fits many models from Replaces OEM (pack of 5) $4.00 Crush Washers Top-quality washers are made in the USA for the following applications. Sold in packs of mm 82-E89 (repl. OEM ) $ mm 84-E91 (repl. OEM ) $ Crush washers, 10 mm, Brake line for Big Twins from (repl. OEM ) Pack of $ Universal Stop Light Switch Sold on a display card of 10, or individually Sold each $ Card of $ Chrome Replacement Stop Light Switches Stamped steel construction and heavy-gauge support plates. Ideal for replacing worn stock parts during a restoration project or when building a ground-up full custom Fits FX, FXE and FXS models (repl. OEM A) pushoff style $ Fits Sportster models (repl. OEM ) pull-on style $ Fits Big Twin models 37-57, 45" WL models and Servicars (repl. OEM T) pull-on style $ Fits Sportster models (repl. OEM T) push-off style $ Fits Sportster and K models (repl. OEM ) pushoff style $10.99 TRAN.16 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.

17 Front for 5-Speed Touring Models and Rear for Sportster Models Replaces OEM Brake pad kits for the rear of all Sportster models from and XLCR s from Also fits the front of all FLT and FLHT models from (repl. OEM ), but you must order two of each part number for a complete brake service on these dual disc models Motor Factory Organic $28.99 Rear 82-E87 Replaces OEM Brake pad kits for the rear Girling caliper on all models (except FLT and FLHT models) from 82-E Motor Factory Organic $23.49 Dual Disc Front Replaces OEM For all dual disc Sportster, FX and FXR models from Packaged 2 pads to a kit (2 sets required for a complete brake service) Motor Factory Organic pad set (2 required) $24.99 Front and Rear Replaces OEMs , Brake pad kits for front and rear disc brake banana caliper applications. Each kit contains two pads. Fits 73 FX and XL models single disc front brake; FL models single disc front brake 73-84; FL models rear disc brake 73-80; FX models rear disc brake.) Motor Factory Organic pad set $22.99 Note: We recommend the replacement of the caliper O-rings and seals whenever replacing brake pads in these calipers. Single Disc Front (Kayaba Forks ONLY) Replaces OEM Brake pad kit for all Sportster and FX models with single disc pie-shaped front brake calipers. Each kit contains two pads and four rivets Motor Factory Organic $9.99 Rear for Touring Models from Replaces OEM Fit the large dual piston rear caliper on 4-and 5-speed Touring models from Motor Factory Organic.... $ TRAN.17