polish / 3 rake (H3281) duralumin / polished

Transcription

1 polish / 3 rake (H3281) duralumin / polished black / 3 rake (H3281-BK) duralumin / black anodized stem: stainless steel visor bracket: aluminum comes with under bearing and dust seal *fits OEM headlight visor *fits bottom mounting headlight *required headlight mounting block for long depth headlight 39INCH PIPE FORK EXTENSIONS 150mm long (H3272) stainless / hard chrome plated sold in pairs DRILLED HEADLIGHT BRACKET for 87up XL & Dyna (H5160) steel / chrome plated for 39mm fork models *may not fit some headlights by interfering the frame neck

2

3 DIAGONAL TANK COVER Small (H3248-S) fits OEM 8.5L Tanks size L:510 W:150mm our Aluminum Sportster Tank Hi-Mount for / 10UP XL (H3243) for 07up XL (H3244) synthetic leather *seamline not waterproof DIAGONAL TANK COVER Large (H3248-L) fits OEM 12L Tanks size L:655 W:170mm synthetic leather *seamline not waterproof SIDE COVER GARNISH (BAT WING) for 04up XL (H1323) fiber glass / black gel coated comes with double stick tape sold in right & left pairs *NOT fit OEM side cover tip simultaneously *NOT fit XR1200X *must be painting before use *must be fitting check before paint SIDE COVER GARNISH (DIMPLES) for 04up XL (H1321) glass fiber / black gel coated comes with double stick tape sold in right & left pairs *NOT fit OEM side cover tip simultaneously *NOT fit XR1200X *must be painting before use *must be fitting check before paint

4 SIDE MOUNTING BRACKET for GENUNE SPEEDOMETER for 04 UP XL (H1322) material : *NOT fit speedo & tachometer (twin meter) models *NOT fit XL883C / XL1200C / XL1200X / XR / SuperLow * XL carburator models required (H1322-A) choke mounting bracket (sold separately). CHOKE MOUNTING BRACKET for XL (H1322-A) material : I/G COIL RELOCATION KIT for XL (H1313) coil bracket: steel / chrome plated ignition bracket: *NOT fit 1200/C/S (not fit the models which have horn mounts on the left side) *requires wiring modification *NOT fit genuine plug wires, required suitable plug wires (sold separately) 04up (H1319) 07up (H1324) SIDE MOUNTING IGNITION COIL BRACKET KIT for 04up XL (H1319) comes with ignition coil switch relocation bracket, coil bracket, choke bracket fits XL carburetor models / 07up XL fuel injection models *NOT fit XL883C, XL1200C, XL883R, XL1200R, XL883L, XL1200L, XR1200R *NOT fit genuine plug wire *required extending some wiring SIDE MOUNTING IGNITION COIL BRACKET & PLUG WIRE KIT for 07up XL (H1324)

5 PASSENGER PEG BRACKET KIT for 04up XL (H4014) sold in right and left set This kit supports you to relocate passenger pegs, not to interfere mufflers, saddlebags. Fitting positions are 6 kinds from a kit! LOW DOWN SUSPENSION for '91up DYNA chrome / chrome (H5358-CH) body: aluminum / clear anodized spring&shaft: steel / chrome plated black / black (H5358-BK) body: aluminum / black anodized spring: black painted shaft: steel / chrome plated eye to eye length:11.0inch *cut mud guard (required) *not fit '90 and under models *NOT fit FXR models REAR TURN SIGNAL OFFSET MOUNT SPACER for 04up XL (H1013) FRAME MOUNT FRONT for 04up XL (H1012) spacer / aluminum black painted *Genuine turn signal corresponding *Turn signal wiring must be processed *Jack is required for mounting steel / black cation painted size W:250mm *Turn signal wiring must be extended processing LOW DOWN SUSPENSION for '91up XL chrome / chrome (H5357-CH) body: aluminum / clear anodized spring&shaft: steel / chrome plated black / chrome (H5357-BC) body: aluminum / black anodized spring&shaft: steel / chrome plated black / black (H5357-BK) body: aluminum / black anodized spring: black painted shaft: steel / chrome plated eye to eye length:10.5inch *cut mud guard (required) *not fit '90 and under models *'91-'93 and '04up models may require some modification BILLET SUSPENSION (BLACK BODY / CHROME SPRING) for '91up XL (H5356) body: aluminum / black anodized spring: chrome eye to eye length: 265mm(10.5inch) *NOT fit ~'90 models *needed some modification for '91~'03 models not to touch tire and fender bolts *it may need to cut the mud guard AXLE ADJUSTER MOUNTING REAR for Dyna / XL (H1010) sold in pairs hole dia. for turn signal: 10.5mm *NOT fit genuine turn signal *NOT fit 06up Dyna and thru 96 & 05up XL FRAME MOUNTING FRONT for 91up Dyna (H1014) steel / black cation painted size W:325mm *Turn signal wiring must be extended processing

6 PASSENGER PEG BRACKET KIT for 04up XL (H4014) sold in right and left set This kit supports you to relocate passenger pegs, not to interfere mufflers, saddlebags. Fitting positions are 6 kinds from a kit! LOW DOWN SUSPENSION for '91up DYNA chrome / chrome (H5358-CH) body: aluminum / clear anodized spring&shaft: steel / chrome plated black / black (H5358-BK) body: aluminum / black anodized spring: black painted shaft: steel / chrome plated eye to eye length:11.0inch *cut mud guard (required) *not fit '90 and under models *NOT fit FXR models REAR TURN SIGNAL OFFSET MOUNT SPACER for 04up XL (H1013) FRAME MOUNT FRONT for 04up XL (H1012) spacer / aluminum black painted *Genuine turn signal corresponding *Turn signal wiring must be processed *Jack is required for mounting steel / black cation painted size W:250mm *Turn signal wiring must be extended processing LOW DOWN SUSPENSION for '91up XL chrome / chrome (H5357-CH) body: aluminum / clear anodized spring&shaft: steel / chrome plated black / chrome (H5357-BC) body: aluminum / black anodized spring&shaft: steel / chrome plated black / black (H5357-BK) body: aluminum / black anodized spring: black painted shaft: steel / chrome plated eye to eye length:10.5inch *cut mud guard (required) *not fit '90 and under models *'91-'93 and '04up models may require some modification BILLET SUSPENSION (BLACK BODY / CHROME SPRING) for '91up XL (H5356) body: aluminum / black anodized spring: chrome eye to eye length: 265mm(10.5inch) *NOT fit ~'90 models *needed some modification for '91~'03 models not to touch tire and fender bolts *it may need to cut the mud guard AXLE ADJUSTER MOUNTING REAR for Dyna / XL (H1010) sold in pairs hole dia. for turn signal: 10.5mm *NOT fit genuine turn signal *NOT fit 06up Dyna and thru 96 & 05up XL FRAME MOUNTING FRONT for 91up Dyna (H1014) steel / black cation painted size W:325mm *Turn signal wiring must be extended processing

7 *Our license kits are designed for Jpan license size. Must be required some modification to fit each country s one HIGH MID CONTROL KIT for 06up DYNA (H4015) *brake peg is sold separately (reuse OEM peg applicable) *100mm UP and 40mm BACK from OEM position. *Required OEM mid control brake torgue rod separately. LICENSE PLATE RELOCATION KIT for 13up BREAKOUT (H5176) license plate / aluminum bracket : *our mid control riding position *Short Flat Bob Rear Fender *Bobber Style Rear Fender Type2 for 04 ~ 13y XL *our mid control riding position for 14up XL mid control model HIGH MID CONTROL KIT for 04~ 13y XL (H4013) for 14up XL mid control model (H4016) forward control model (H4017) *brake peg is sold separately (reuse OEM peg applicable) *60mm UP and 40mm BACK from OEM mid control position. *58mm UP and 210mm BACK from OEM forward control position. for 14up XL forward control model LED INSIDE MOUNTING TAILLIGHT KIT for 09up XL883/1200N, XL1200V and XL1200X clear lens (H5172-CL) smoke lens (H5172-SM) red lens (H5172-RD) comes with reflector and connectors *fits OEM fender, our BOBBER STYLE REAR FENDER & SHORT FLAT BOB REAR FENDER *NOT fit with OEM license bracket *required side license mounting (sold separately) *stock Fender

8 *Our license kits are designed for Jpan license size. Must be required some modification to fit each country s one HIGH MID CONTROL KIT for 06up DYNA (H4015) *brake peg is sold separately (reuse OEM peg applicable) *100mm UP and 40mm BACK from OEM position. *Required OEM mid control brake torgue rod separately. LICENSE PLATE RELOCATION KIT for 13up BREAKOUT (H5176) license plate / aluminum bracket : *our mid control riding position *Short Flat Bob Rear Fender *Bobber Style Rear Fender Type2 for 04 ~ 13y XL *our mid control riding position for 14up XL mid control model HIGH MID CONTROL KIT for 04~ 13y XL (H4013) for 14up XL mid control model (H4016) forward control model (H4017) *brake peg is sold separately (reuse OEM peg applicable) *60mm UP and 40mm BACK from OEM mid control position. *58mm UP and 210mm BACK from OEM forward control position. for 14up XL forward control model LED INSIDE MOUNTING TAILLIGHT KIT for 09up XL883/1200N, XL1200V and XL1200X clear lens (H5172-CL) smoke lens (H5172-SM) red lens (H5172-RD) comes with reflector and connectors *fits OEM fender, our BOBBER STYLE REAR FENDER & SHORT FLAT BOB REAR FENDER *NOT fit with OEM license bracket *required side license mounting (sold separately) *stock Fender

9 *Our license kits are designed for Jpan license size. Must be required some modification to fit each country s one SIDE MOUNT NUMBER BRACKET KIT for 13up Breakout plate : aluminum bracket: steel /black painted (H5172) bracket: stainless/polished (H5177) *CVO models require axle nut (HD2603) washer (HD2606)separetely SIDE MOUNT LICENCE PLATE& for 91UP XL (H5165) or Dyna (H5166) SIDE MOUNT NUMBER BRACKET KIT for 08up Softail 200Tire / 07up Dyna (H5164) SIDE MOUNT NUMBER BRACKET KIT for Softail (H5167) BULB Type LED RED Type LED CLEAR Type FLARE TAILLIGHT (black) BULB (5910-A) LED RED (5910-AR) LED CLEAR (5910-AC) CURLY TAILLIGHT (black) BULB (5216-A) LED RED (5216-AR) LED CLEAR (5216-AC) (brass) BULB (5349-A) LED RED (5349-AR) LED CLEAR (5349-AC) (aluminum) BULB (5348-A) LED RED (5348-AR) LED CLEAR (5348-AC) DRILLED TAILLIGHT (black / gold) BULB (5891-A) LED RED (5891-AR) LED CLEAR (5891-AC) DRILLED TAILLIGHT (black) BULB (5840-A) LED RED (5840-AR) LED CLEAR (5840-AC) (alumi /black contrast) BULB (5904-ABA) LED RED (5904-BAR) LED CLEAR (5904-BAC) ( alumi ) BULB (5904-AAL) LED RED (5904-ALR) LED CLEAR (5904-ALC) (black /black contrast2) BULB (5905-AAB) LED RED (5905-ABR) LED CLEAR (5905-ABC) (black) BULB (5905-ABK) LED RED (5905-BKR) LED CLEAR (5905-BKC) CHOPPER TAILLIGHT BULB (5208-A) LED RED (5208-AR) LED CLEAR (5208-AC) DUO TAILLIGHT (5808-A) MINI CATEYE TAILLIGHT (5232-A) MINI MINI LUCAS TAILLIGHT (5245-A)

10 *Our license kits are designed for Jpan license size. Must be required some modification to fit each country s one SIDE MOUNT LICENCE PLATE& for 08up Softail 200Tire / 07up Dyna (H5171) SIDE MOUNT LICENCE PLATE& for Softail (H5170) SIDE MOUNT LICENCE PLATE& for 13up Breakout plate : aluminum bracket: steel /black painted (H5178) bracket: stainless/polished (H5173) *CVO models require axle nut (HD2603) washer (HD2606)separetely SIDE MOUNT LICENCE PLATE& for 91UP XL (H5168) or Dyna (H5169) HISIDE MOUNT LICENCE PLATE& for 94UP XL (H5180) Change turn signals may required HISIDE MOUNT NUMBER BRACKET KIT <Length and side common use> for 94UP XL (H5179) Change turn signals may required FXSB BRAKEOUT REAR AXLE NUT [8184] (HD2603) steel ROUND ALUMI LICENCE PLATE KIT (5916) aluminum FXSB BRAKEOUT REAR AXLE WASHER [6551] (HD2606) steel