Design of a Microcontroller-Based Photo-Controlled Circuit for Adjusting the Speed of DC Motors
|
|
|
- Darrell Dennis
- 7 years ago
- Views:
Transcription
1 مجلة المنصور / العدد ) 22 ( 2014 ) 22 /Issue( Al-Mansour Journal Design of a Microcontroller-Based Photo-Controlled Circuit for Adjusting the Speed of DC Motors (Assist. Lecturer)Firas Mohammed Ali Al-Raie* Abstract There are many approaches and methods for changing the speed of DC motors. One of these approaches is through the intensity of light. In this paper, a microcontroller-based control circuit for adjusting the speed of a DC motor by means of interrupting the incident light is proposed and implemented. The adopted technique in this circuit uses two light dependent resistors as photo-sensors to detect the illumination of light by producing a prescribed digital sequence to activate one of the input ports of an 8051 microcontroller. An assembly program stored in the on-chip program memory of the microcontroller generates the proper PWM signal at an output port based on the received sequence. This signal is supplied to the driving circuit of the motor in order to run it with the relevant speed. The circuit has been implemented and tested successfully in the laboratory. Keywords: 8051 Microcontroller, Motor Speed Control, PWM, Photosensors. * Electrical Engineering Dept., University of Technology
2
3
4
5
6
7
8
9
10
11
12
13
Computer and Set of Robots
Lesson 11:DESIGN PROCESS EXAMPLES Mobile-Phone, Mobile- Computer and Set of Robots 1 Mobile Phone 2 Mobile phone SoC (System-on-Chip) Hardware units Microcontroller or ASIP (Application Specific Instruction
ETEC 421 - Digital Controls PIC Lab 10 Pulse Width Modulation
ETEC 421 - Digital Controls PIC Lab 10 Pulse Width Modulation Program Definition: Write a program to control the speed of a dc motor using pulse width modulation. Discussion: The speed of a dc motor is
Lab Experiment 1: The LPC 2148 Education Board
Lab Experiment 1: The LPC 2148 Education Board 1 Introduction The aim of this course ECE 425L is to help you understand and utilize the functionalities of ARM7TDMI LPC2148 microcontroller. To do that,
Microtronics technologies Mobile: 99707 90092
For more Project details visit: http://www.projectsof8051.com/rfid-based-attendance-management-system/ Code Project Title 1500 RFid Based Attendance System Synopsis for RFid Based Attendance System 1.
Table 1 Comparison of DC, Uni-Polar and Bi-polar Stepper Motors
Electronics Exercise 3: Uni-Polar Stepper Motor Controller / Driver Mechatronics Instructional Laboratory Woodruff School of Mechanical Engineering Georgia Institute of Technology Lab Director: I. Charles
A 5 Degree Feedback Control Robotic Arm (Haptic Arm)
A 5 Degree Feedback Control Robotic Arm (Haptic Arm) 1 Prof. Sheetal Nirve, 2 Mr.Abhilash Patil, 3 Mr.Shailesh Patil, 4 Mr.Vishal Raut Abstract: Haptics is the science of applying touch sensation and control
Teaching Systems Integration In An Advanced Microprocessor Applications Course
Teaching Systems Integration In An Advanced Microprocessor Applications Course Phil Fabiano New Jersey Institute of Technology University Heights Newark, New Jersey 07102 Abstract The New Jersey Institute
Microcontrollers in Practice
M. Mitescu I. Susnea Microcontrollers in Practice With 117 Figures, 34 Tables and CD-Rom 4y Springer Contents Resources of Microcontrollers, 1 1.1 In this Chapter 1 1.2 Microcontroller Architectures 1
Microcontroller-based experiments for a control systems course in electrical engineering technology
Microcontroller-based experiments for a control systems course in electrical engineering technology Albert Lozano-Nieto Penn State University, Wilkes-Barre Campus, Lehman, PA, USA E-mail: AXL17@psu.edu
Selecting and Implementing H-Bridges in DC Motor Control. Daniel Phan A37005649
Selecting and Implementing H-Bridges in DC Motor Control Daniel Phan A37005649 ECE 480 Design Team 3 Spring 2011 Abstract DC motors can be used in a number of applications that require automated movements.
1. Learn about the 555 timer integrated circuit and applications 2. Apply the 555 timer to build an infrared (IR) transmitter and receiver
Electronics Exercise 2: The 555 Timer and its Applications Mechatronics Instructional Laboratory Woodruff School of Mechanical Engineering Georgia Institute of Technology Lab Director: I. Charles Ume,
Theory and Practice of Tangible User Interfaces. Thursday Week 2: Digital Input and Output. week. Digital Input and Output. RGB LEDs fade with PWM
week 02 Digital Input and Output RGB LEDs fade with PWM 1 Microcontrollers Output Transducers actuators (e.g., motors, buzzers) Arduino Input Transducers sensors (e.g., switches, levers, sliders, etc.)
Using Arduino Microcontrollers to Sense DC Motor Speed and Position
ECE480 Design Team 3 Using Arduino Microcontrollers to Sense DC Motor Speed and Position Tom Manner April 4, 2011 page 1 of 7 Table of Contents 1. Introduction ----------------------------------------------------------
Home Security System Design and Implementation
Home Security System Design and Implementation Mohamed Hassan Ali Mohamed 1, Dalia Mahmoud 2 1 Alneelain University, College of Graduates Studies, MSC in Control System Engineering, Khartoum, Sudan 2Assistan
Monitoring of Intravenous Drip Rate
Monitoring of Intravenous Drip Rate Vidyadhar V. Kamble, Prem C. Pandey, Chandrashekar P. Gadgil, and Dinesh S. Choudhary Abstract A drip rate meter, for monitoring intravenous infusion, is developed using
Microcontroller Based Anti-theft Security System Using GSM Networks with Text Message as Feedback
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 2, Issue 10 (August 2012), PP. 18-22 Microcontroller Based Anti-theft Security System
EVAL-UFDC-1/UFDC-1M-16
Evaluation Board for Universal Frequency-to- Digital Converters UFDC-1 and UFDC-1M-16 EVAL-UFDC-1/UFDC-1M-16 FEATURES Full-Featured Evaluation Board for the Universal Frequency-to-Digital Converters UFDC-1
Switch board datasheet EB007-00-1
Switch board datasheet EB007-00-1 Contents 1. About this document... 2 2. General information... 3 3. Board layout... 4 4. Testing this product... 5 5. Circuit description... 6 Appendix 1 Circuit diagram
Innovative Practices in Optimal Utilization of Solar Energy (Solar Tracking System)
Innovative Practices in Optimal Utilization of Solar Energy (Solar Tracking System) Dr. G. Suresh Babu EEE Dept., C.B.I.T Abstract: As the demand is ahead of the supply there is a dire need for efficient
ECE 495 Project 3: Shocker Actuator Subsystem and Website Design. Group 1: One Awesome Engineering
ECE 495 Project 3: Shocker Actuator Subsystem and Website Design Group 1: One Awesome Engineering Luquita Edwards Evan Whetsell Sunny Verma Thomas Ryan Willis Long I. Executive Summary The main goal behind
PROJECT PRESENTATION ON CELLPHONE OPERATED ROBOTIC ASSISTANT
PROJECT PRESENTATION ON CELLPHONE OPERATED ROBOTIC ASSISTANT ELECTRONICS ENGINEERING DEPARTMENT SVNIT, SURAT-395007, INDIA Prepared by: Anurag Gupta (U05EC401) Dhrumeel Bakshi (U05EC326) Dileep Dhakal
Experiment # (4) AM Demodulator
Islamic University of Gaza Faculty of Engineering Electrical Department Experiment # (4) AM Demodulator Communications Engineering I (Lab.) Prepared by: Eng. Omar A. Qarmout Eng. Mohammed K. Abu Foul Experiment
USER GUIDE Programming Adapter Cable for Fujitsu Flash Microcontroller- F²MC-16LX/FR Family Fujitsu Microelectronics America, Inc.
USER GUIDE Programming Adapter Cable for Fujitsu Flash Microcontroller- F²MC-16LX/FR Family Fujitsu Microelectronics America, Inc. 1 Revision History Revision # Date Comment 1.0 03.25.2001 New Document
Automatic Railway Gate Controller with High Speed Alerting System
Automatic Railway Gate Controller with High Speed Alerting System Vikash Kumar 1, Prajit Paul 2, Nishant kumar 1, Pratik kumar Sinha 1, Sumant Kumar Mahato 1 B. Tech Student, Dept. of ECE, Asansol Engineering
CHAPTER 11: Flip Flops
CHAPTER 11: Flip Flops In this chapter, you will be building the part of the circuit that controls the command sequencing. The required circuit must operate the counter and the memory chip. When the teach
ES_LPC4357/53/37/33. Errata sheet LPC4357/53/37/33. Document information
Rev. 1.1 8 August 2012 Errata sheet Document information Info Keywords Abstract Content LPC4357FET256; LPC4357FET180; LPC4357FBD208; LPC4353FET256; LPC4353FET180; LPC4353FBD208; LPC4337FET256; LPC4337FET180;
Points Position Indicator (PPI1) for Points Motors with Common Ground
Points Position Indicator (PPI1) for Points Motors with Common Ground Monitors Points Action and Operates Leds on a Control Panel Monitors the brief positive operating voltage across points motors when
Micro-Step Driving for Stepper Motors: A Case Study
Micro-Step Driving for Stepper Motors: A Case Study N. Sedaghati-Mokhtari Graduate Student, School of ECE, University of Tehran, Tehran, Iran n.sedaghati @ece.ut.ac.ir Abstract: In this paper, a case study
REMOTE HOST PROCESS CONTROL AND MONITORING OF INDUSTRY APPLIANCES
REMOTE HOST PROCESS CONTROL AND MONITORING OF INDUSTRY APPLIANCES 1 Abinath.T.R, 2 Sudhakar.V, 3 Sasikala.S 1,2 UG Scholar, Department of Electrical and Electronics Engineering, Info Institute of Engineering,
STEPPER MOTOR SPEED AND POSITION CONTROL
STEPPER MOTOR SPEED AND POSITION CONTROL Group 8: Subash Anigandla Hemanth Rachakonda Bala Subramanyam Yannam Sri Divya Krovvidi Instructor: Dr. Jens - Peter Kaps ECE 511 Microprocessors Fall Semester
FEEDBACK ICANE FOR STROKE PATIENT
International Journal of Computer Engineering & Technology (IJCET) Volume 7, Issue 1, Jan-Feb 2016, pp. 88-93, Article ID: IJCET_07_01_010 Available online at http://www.iaeme.com/ijcet/issues.asp?jtype=ijcet&vtype=7&itype=1
APPLICATION NOTES: Dimming InGaN LED
APPLICATION NOTES: Dimming InGaN LED Introduction: Indium gallium nitride (InGaN, In x Ga 1-x N) is a semiconductor material made of a mixture of gallium nitride (GaN) and indium nitride (InN). Indium
Smart Automated Conference Room System
Smart Automated Conference Room System Prof. P. P. Chitte 1, R. R. Shinde 2, S. V. Thosar 3 1 Assistant Professor, P.R.E.C. Loni, India 2,3 Student, P.R.E.C. Loni, India Abstract: In video conference system
Eric Mitchell April 2, 2012 Application Note: Control of a 180 Servo Motor with Arduino UNO Development Board
Eric Mitchell April 2, 2012 Application Note: Control of a 180 Servo Motor with Arduino UNO Development Board Abstract This application note is a tutorial of how to use an Arduino UNO microcontroller to
Design,DevelopmentandPerformanceStudyofL-HomeSecuritySystem
Global Journal of Researches in Engineering Electrical and Electronics Engineering Volume 12 Issue 8 Version 1.0 Type: Double Blind Peer Reviewed International Research Journal Publisher: Global Journals
SECURITY SYSTEM IN INDUSTRIES USING ZIGBEE TECHNOLOGY
SECURITY SYSTEM IN INDUSTRIES USING ZIGBEE TECHNOLOGY 1 S. Ashmad, 2 M.Mohan Babu, 3 P. Sudheer Asst. Professor, Department of E.I.E, SITAMS, Affiliated to JNTUA University, Chittoor, A.P Email : ashmad.syed@gmail.com,
VOICE RECOGNITION KIT USING HM2007. Speech Recognition System. Features. Specification. Applications
VOICE RECOGNITION KIT USING HM2007 Introduction Speech Recognition System The speech recognition system is a completely assembled and easy to use programmable speech recognition circuit. Programmable,
LED board datasheet EB004-00-2
LED board datasheet EB004-00-2 Contents 1 About this document... 2 2 General information... 3 3 Board layout... 4 4 Testing this product... 5 5 Circuit description... 6 Appendix 1 Circuit Diagram Copyright
MECE 102 Mechatronics Engineering Orientation
MECE 102 Mechatronics Engineering Orientation Mechatronic System Components Associate Prof. Dr. of Mechatronics Engineering Çankaya University Compulsory Course in Mechatronics Engineering Credits (2/0/2)
Electronics course for in-service teachers of engineering and technology
World Transactions on Engineering and Technology Education Vol.10, No.1, 2012 2012 WIETE Electronics course for in-service teachers of engineering and technology Gorazd Šantej & Slavko Kocijancic University
Microcontroller Based Low Cost Portable PC Mouse and Keyboard Tester
Leonardo Journal of Sciences ISSN 1583-0233 Issue 20, January-June 2012 p. 31-36 Microcontroller Based Low Cost Portable PC Mouse and Keyboard Tester Ganesh Sunil NHIVEKAR *, and Ravidra Ramchandra MUDHOLKAR
Designing an efficient Programmable Logic Controller using Programmable System On Chip
Designing an efficient Programmable Logic Controller using Programmable System On Chip By Raja Narayanasamy, Product Apps Manager Sr, Cypress Semiconductor Corp. A Programmable Logic Controller (PLC) is
Product Guide AC Voltage Control Devices. Guide Guide. Popular Variable Transformers and AC Power Supplies. www.stacoenergy.com
Popular Variable Transformers and AC Power Supplies Product Guide AC Voltage Control Devices Guide Guide Your Tailored Power Solutions Provider TM Staco Energy Products Co. has been a leading manufacturer
DEPARTMENT OF COMPUTER SCIENCE & ENGINEERING Question Bank Subject Name: EC6504 - Microprocessor & Microcontroller Year/Sem : II/IV
DEPARTMENT OF COMPUTER SCIENCE & ENGINEERING Question Bank Subject Name: EC6504 - Microprocessor & Microcontroller Year/Sem : II/IV UNIT I THE 8086 MICROPROCESSOR 1. What is the purpose of segment registers
APPLICATION NOTE. Atmel AVR443: Sensor-based Control of Three Phase Brushless DC Motor. Atmel AVR 8-bit Microcontrollers. Features.
APPLICATION NOTE Features Atmel AVR443: Sensor-based Control of Three Phase Brushless DC Motor Less than 5µs response time on Hall sensor output change Theoretical maximum of 1600k RPM Over-current sensing
Experiment 2 Introduction to TI C2000 Microcontroller, Code Composer Studio (CCS) and Matlab Graphic User Interface (GUI)
1 Experiment 2 Introduction to TI C2000 Microcontroller, Code Composer Studio (CCS) and Matlab Graphic User Interface (GUI) 2.1 Objectives The objective of this experiment is to familiarize the students
Degree programme in Automation Engineering
Degree programme in Automation Engineering Course descriptions of the courses for exchange students, 2014-2015 Autumn 2014 21727630 Application Programming Students know the basis of systems application
KEYWORDS: Cellphone, Braille language, Visually impaired people(vip), Microcontroller, Decoder, Latches, DC motors.
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY CELLPHONE FOR VISUALLY IMPAIRED PEOPLE USING MICROCONTROLLER Akshay Baghmar*, Tousif Kazi, Prof. Nitin Deotale ABSTRACT The mobile
8-Bit Flash Microcontroller for Smart Cards. AT89SCXXXXA Summary. Features. Description. Complete datasheet available under NDA
Features Compatible with MCS-51 products On-chip Flash Program Memory Endurance: 1,000 Write/Erase Cycles On-chip EEPROM Data Memory Endurance: 100,000 Write/Erase Cycles 512 x 8-bit RAM ISO 7816 I/O Port
Experiment 8 : Pulse Width Modulation
Name/NetID: Teammate/NetID: Experiment 8 : Pulse Width Modulation Laboratory Outline In experiment 5 we learned how to control the speed of a DC motor using a variable resistor. This week, we will learn
EFC 3600. Frequency converters
2 Bosch Rexroth AG Electric Drives and Controls Documentation Compact and complete: space saving side-by-side assembly, plug-in I/O terminals, with brake chopper and mains filter for ultra-simple installation
Certificate of Compliance
No. 0V151007.CFMTW07 Brushless Dc motor FL42BLS01(CE), FL16, FL20, FL22, FL24, FL28, FL32, FL33, FL36, FL42, FL45 EN 61000-6-3:2007+A1:2011, EN 61000-6-1:2007, EN 55014-2:1997+A1:2001+A2:2008, No. 0V151007.CFMTW08
0832 Dot Matrix Green Display Information Board User s Guide
0832 Dot Matrix Green Display Information Board User s Guide DE-DP105_Ver1.0 0832 DOT MATRIX GREEN DISPLAY INFORMATI BOARD USER S GUIDE Table of contents Chapter1.Overview... 1 1.1. Welcome... 1 1.2. Quick
GPS INSTALLATION & USER GUIDE. Internet. Compatible with the following controllers. Nomad SD/SD2. ALL RIGHTS RESERVED Rev 03.25.11
GPS INSTALLATION & USER GUIDE Compatible with the following controllers TV Nomad 3 Nomad SD/SD2 Internet MESA ALL RIGHTS RESERVED Rev 03.25.11 INDEX BILL OF MATERIALS Components for configuration 3 BLOCK
Fuzzy Irrigation Controller Using Solar Energy
Fuzzy Irrigation Controller Using Solar Energy Eltahir Hussan 1, Ali Hamouda 2, HassanChaib 3 Associate Professor, Dept. of ME, Engineering College, Sudan University, Sudan 1 Instrumentation Assessor,
POINTS POSITION INDICATOR PPI4
POINTS POSITION INDICATOR PPI4 Advanced PPI with Adjustable Brightness & Simplified Wiring Monitors the brief positive operating voltage across points motors when they are switched Lights a corresponding
Programming PIC Microcontrollers in PicBasic Pro Lesson 1 Cornerstone Electronics Technology and Robotics II
Programming PIC Microcontrollers in PicBasic Pro Lesson 1 Cornerstone Electronics Technology and Robotics II Administration: o Prayer PicBasic Pro Programs Used in This Lesson: o General PicBasic Pro Program
Chapter 13. PIC Family Microcontroller
Chapter 13 PIC Family Microcontroller Lesson 01 PIC Characteristics and Examples PIC microcontroller characteristics Power-on reset Brown out reset Simplified instruction set High speed execution Up to
V out. Figure 1: A voltage divider on the left, and potentiometer on the right.
Living with the Lab Fall 202 Voltage Dividers and Potentiometers Gerald Recktenwald v: November 26, 202 gerry@me.pdx.edu Introduction Voltage dividers and potentiometers are passive circuit components
LOW COST MOTOR PROTECTION FILTERS FOR PWM DRIVE APPLICATIONS STOPS MOTOR DAMAGE
LOW COST MOTOR PROTECTION FILTERS FOR PWM DRIVE APPLICATIONS STOPS MOTOR DAMAGE Karl M. Hink, Executive Vice President Originally presented at the Power Quality 99 Conference ABSTRACT Motor protection
DSO138 oscilloscope program upgrade method
DSO138 oscilloscope program upgrade method Applicable models: 13801K, 13802K Program upgrade Principle The DSO138 is a SCM STM32F103C8 internal oscilloscope that is preinstalled with a flash bootloader,
PROCEDURE: 1. Measure and record the actual values of the four resistors listed in Table 10-1.
The answer to two questions will help you identify a series or parallel connection: (1) Will the identical current go through both components? f the answer is yes, the components are in series. (2) Are
Building Blocks for PRU Development
Building Blocks for PRU Development Module 1 PRU Hardware Overview This session covers a hardware overview of the PRU-ICSS Subsystem. Author: Texas Instruments, Sitara ARM Processors Oct 2014 2 ARM SoC
Freescale Semiconductor, I
nc. Application Note 6/2002 8-Bit Software Development Kit By Jiri Ryba Introduction 8-Bit SDK Overview This application note describes the features and advantages of the 8-bit SDK (software development
Isolation of Battery Chargers Integrated Into Printed Circuit Boards
LLNL-TR-646864 Isolation of Battery Chargers Integrated Into Printed Circuit Boards J. S. Sullivan November 26, 2013 Disclaimer This document was prepared as an account of work sponsored by an agency of
Electronics I - Laboratory 1 Diode I/V Characteristics
Electronics I - Laboratory 1 Diode I/V Characteristics I. Objectives 1. Develop I/V characteristics of a silicon diode. 2. Develop I/V characteristics of a germanium diode. 3. Develop I/V characteristics
PICNet 1. PICNet 1 PIC18 Network & SD/MMC Development Board. Features. Applications. Description
Features PICNet 1 PIC18 Network & SD/MMC Development Board IC Sockets for 28 or 40-pin Microchip PIC18F Microcontrollers IC Socket for 8-pin serial EEPROM Multiple MCU Oscillator sources Full 10BaseT IEEE
udrive-usd-g1 Embedded DOS micro-drive Module Data Sheet
4D SYSTEMS udrie-usd-g1 Embedded DOS micro-drive Module Document Date: 2nd April 2009 Document Revision: 2.0 Page 1 of 9 udrie-usd-g1 Embedded DOS micro-drive 4D SYSTEMS Description Features The is an
The Design of DSP controller based DC Servo Motor Control System
International Conference on Advances in Energy and Environmental Science (ICAEES 2015) The Design of DSP controller based DC Servo Motor Control System Haiyan Hu *, Hong Gu, Chunguang Li, Xiaowei Cai and
PROGRAM CRITERIA FOR ELECTRICAL ENGINEERING TECHNOLOGY
PROGRAM CRITERIA FOR ELECTRICAL ENGINEERING TECHNOLOGY Scope These program criteria apply to programs having titles involving Electrical Engineering Technology including: electrical engineering, electrical
TS1005 Demo Board COMPONENT LIST. Ordering Information. SC70 Packaging Demo Board SOT23 Packaging Demo Board TS1005DB TS1005DB-SOT
REVISION NOTE The current revision for the TS1005 Demo Boards display the identifier TS100x Demo Board on the top side of the evaluation board as depicted in Figure 1. If the identifier is not printed
Digital Signal Controller Based Automatic Transfer Switch
Digital Signal Controller Based Automatic Transfer Switch by Venkat Anant Senior Staff Applications Engineer Freescale Semiconductor, Inc. Abstract: An automatic transfer switch (ATS) enables backup generators,
Design and Construction of Variable DC Source for Laboratory Using Solar Energy
International Journal of Electronics and Computer Science Engineering 228 Available Online at www.ijecse.org ISSN- 2277-1956 Design and Construction of Variable DC Source for Laboratory Using Solar Energy
dspic30f4012 Microcontroller
dspic30f4012 Microcontroller dspic30f4012 is manufactured by Microchip, and is about $6 Specifications: 28-pin, 16-bit microcontroller 24-bit wide instructions 16-bit wide data path 48 Kbytes on-chip flash
PolyBot Board. User's Guide V1.11 9/20/08
PolyBot Board User's Guide V1.11 9/20/08 PolyBot Board v1.1 16 pin LCD connector 4-pin SPI port (can be used as digital I/O) 10 Analog inputs +5V GND GND JP_PWR 3-pin logic power jumper (short top 2 pins
revolution Contents: Introduction Power 28-pin Project Board with input/output cables
28-PIN IN IN PROJECT BOARD Contents: AXE020 28-pin Project Board with input/output cables Introduction The 28-pin project board is designed to allow rapid prototyping with 28-pin PICAXE microcontrollers.
PLC Based Liquid Filling and Mixing
PLC Based Liquid Filling and Mixing 1 Mihir Panchal, 2 Aashish Panaskar. 3 Prof. Lalit Kumar KJ College of Engineering and Management Research, Pune, India Abstract: The objective of this paper is to design,
Display Message on Notice Board using GSM
Advance in Electronic and Electric Engineering. ISSN 2231-1297, Volume 3, Number 7 (2013), pp. 827-832 Research India Publications http://www.ripublication.com/aeee.htm Display Message on Notice Board
COMPUTER SCIENCE AND ENGINEERING - Microprocessor Systems - Mitchell Aaron Thornton
MICROPROCESSOR SYSTEMS Mitchell Aaron Thornton, Department of Electrical and Computer Engineering, Mississippi State University, PO Box 9571, Mississippi State, MS, 39762-9571, United States. Keywords:
Using The PIC I/O Ports
EE2801 -- Lecture 22 Using The PIC I/O Ports EE2801-L22P01 The Variety Of Available IO Ports The PIC 16F874 microcontroller has five different IO ports, accounting for thirty three of the processors forty
EXPERIMENT 2 TRAFFIC LIGHT CONTROL SYSTEM FOR AN INTERSECTION USING S7-300 PLC
YEDITEPE UNIVERSITY ENGINEERING & ARCHITECTURE FACULTY INDUSTRIAL ELECTRONICS LABORATORY EE 432 INDUSTRIAL ELECTRONICS EXPERIMENT 2 TRAFFIC LIGHT CONTROL SYSTEM FOR AN INTERSECTION USING S7-300 PLC Introduction:
Invisible EYE for Security System
Invisible EYE for Security System 1 C.Chandravathi, 2 Geetha, 3 Shanmugapriya, 4 Kavitha 1 chandravath.jay@gmail.com, 2 geetharamadoss2011@gmail.com, 3 shanmuga393@gmail.com, 4 kavithasmile04@gmail.com
Embedded Software development Process and Tools: Lesson-4 Linking and Locating Software
Embedded Software development Process and Tools: Lesson-4 Linking and Locating Software 1 1. Linker 2 Linker Links the compiled codes of application software, object codes from library and OS kernel functions.
MIDECO 64-outputs MIDI note decoder USER MANUAL. Roman Sowa 2012
MIDECO 64-outputs MIDI note decoder USER MANUAL Roman Sowa 2012 www.midi-hardware.com 1.Overview Thank you for choosing MIDECO as your new MIDI-to-digital converter. This short manual will guide you through
Electrical Symbols and Line Diagrams
Electrical Symbols and Line Diagrams Chapter 3 Material taken from Chapter 3 of One-Line Diagrams One-line diagram a diagram that uses single lines and graphic symbols to indicate the path and components
Lesson-16: Real time clock DEVICES AND COMMUNICATION BUSES FOR DEVICES NETWORK
DEVICES AND COMMUNICATION BUSES FOR DEVICES NETWORK Lesson-16: Real time clock 1 Real Time Clock (RTC) A clock, which is based on the interrupts at preset intervals. An interrupt service routine executes
SIMPLE TECHNIQUES TO IMPROVE SOLAR PANEL EFFICIENCY USING A MICROCONTROLLER OR SOC
SIMPLE TECHNIQUES TO IMPROVE SOLAR PANEL EFFICIENCY USING A MICROCONTROLLER OR SOC By Udayan Umapathi, Applications Engineer at Cypress Semiconductor and Gautam Das G, Applications Engineer at Cypress
DESIGN AND IMPLEMENTATION OF A SIMPLE, LOW-COST ROBOTIC ARM
DESIGN AND IMPLEMENTATION OF A SIMPLE, LOW-COST ROBOTIC ARM Mashad Uddin Saleh 1, Gazi Mahamud Hasan 2, Mohammad Abdullah Al Shohel 3, Md. Abul Hasnat Ferdous 4, Biswajit Biswas Dipan 5 Alumni, Dept. of
Accident Notification System by using Two Modems GSM and GPS
Accident Notification System by using Two Modems GSM and GPS Hajer Salim Humaid AL-Farsi Electronic Engineering Student Caledonian College of Engineering, Muscat Malathi B. N. Senior Lecturer, Department
Robot Board Sub-System Testing. Abstract. Introduction and Theory. Equipment. Procedures. EE 101 Spring 2006 Date: Lab Section # Lab #6
EE 101 Spring 2006 Date: Lab Section # Lab #6 Name: Robot Board Sub-System Testing Partner: No Lab partners this time! Abstract The ECEbot robots have a printed circuit board (PCB) containing most of the
LEVERAGING FPGA AND CPLD DIGITAL LOGIC TO IMPLEMENT ANALOG TO DIGITAL CONVERTERS
LEVERAGING FPGA AND CPLD DIGITAL LOGIC TO IMPLEMENT ANALOG TO DIGITAL CONVERTERS March 2010 Lattice Semiconductor 5555 Northeast Moore Ct. Hillsboro, Oregon 97124 USA Telephone: (503) 268-8000 www.latticesemi.com
CELL PHONE CONTROL ROBOT CAR
CELL PHONE CONTROL ROBOT CAR Sakshi Choudhary 1, Satendra Singh 2, Vikrant 3, SK Dubey 4 1,2 UG Students of Department of ECE AIMT, Greater Noida (India) 3 Assistant Professor, Department of ECE AIMT,
Speed Controller 4-Quadrant PWM configurable via PC
4-Quadrant PWM configurable via PC For combination with: DC-Micromotors and Brushless DC-Servomotors Series Power supply for electronic Power supply for motor Max. continuous output current Max. peak output
Protected Cash Withdrawal in Atm Using Mobile Phone
www.ijecs.in International Journal Of Engineering And Computer Science ISSN:2319-7242 Volume 2 Issue 4 April, 2013 Page No. 1346-1350 Protected Cash Withdrawal in Atm Using Mobile Phone M.R.Dineshkumar
The I2C Bus. NXP Semiconductors: UM10204 I2C-bus specification and user manual. 14.10.2010 HAW - Arduino 1
The I2C Bus Introduction The I2C-bus is a de facto world standard that is now implemented in over 1000 different ICs manufactured by more than 50 companies. Additionally, the versatile I2C-bus is used
L297 STEPPER MOTOR CONTROLLERS
L297 STEPPER MOTOR CONTROLLERS NORMAL/WAVE DRIVE HALF/FULL STEP MODES CLOCKWISE/ANTICLOCKWISE DIRECTION SWITCHMODE LOAD CURRENT REGULA- TION PROGRAMMABLE LOAD CURRENT FEW EXTERNAL COMPONENTS RESET INPUT
DS1104 R&D Controller Board
DS1104 R&D Controller Board Cost-effective system for controller development Highlights Single-board system with real-time hardware and comprehensive I/O Cost-effective PCI hardware for use in PCs Application
Chapter 12. Development Tools for Microcontroller Applications
Chapter 12 Development Tools for Microcontroller Applications Lesson 01 Software Development Process and Development Tools Step 1: Development Phases Analysis Design Implementation Phase 1 Phase 2 Phase
Arduino Motor Shield (L298) Manual
Arduino Motor Shield (L298) Manual This DFRobot L298 DC motor driver shield uses LG high power H-bridge driver Chip L298P, which is able to drive DC motor, two-phase or four phase stepper motor with a
Special Lecture. Basic Stamp 2 Programming. (Presented on popular demand)
Special Lecture Basic Stamp 2 Programming (Presented on popular demand) Programming Environment Servo Motor: How It Work? The editor window consists of the main edit pane with an integrated explorer panel