APPLICATION NOTES: Dimming InGaN LED
|
|
- Evangeline Lawson
- 1 years ago
- Views:
Transcription
1 APPLICATION NOTES: Dimming InGaN LED Introduction: Indium gallium nitride (InGaN, In x Ga 1-x N) is a semiconductor material made of a mixture of gallium nitride (GaN) and indium nitride (InN). Indium gallium nitride is the light-emitting layer in modern blue, green and white LEDs and often grown on a transparent substrate such as sapphire or silicon carbide. Characteristic Of InGaN LED While the InGaN produces the brightest light output across blue, true green and white, it shows a dependency of wavelength shift across varying forward current. The typical relationship between the forward current change versus the wavelength or CxCy shift are depicted in Fig 1 - Fig 5 below : Figure 1 SPNova InGaN Blue Figure 2 SPNova InGaN Cyan -1-
2 Figure 3 SPNova InGaN True Green Figure 4 SPNova InGaN Warm White Figure 5 SPNova InGaN White The magnitude of shift for InGaN LED is proportional to the wavelength, longer wavelength ( eg. True green ) will shift more compared to shorter wavelength ( eg. Blue ). Due to wafer process variation, the exact magnitude of shift might vary from one LED chip to another. As comparison, Aluminum Indium Gallium Phosphate (AlInGaP) technology LED exhibits only little changes in wavelength with varying forward current ( Fig 6 Fig 7 ). AlInGaP technology is to produce LED with color from hyper red to pure green
3 Figure 6 SPNova AlInGaP Yellow Figure 7 SPNova AlInGaP Red Dimming InGaN LED Using PWM Due to this unique characteristic of InGaN, dimming an LED by the common method of varying forward voltage or forward current will effectively shift the dominant wavelength and thus shifting the color. In application where this shift of dominant wavelength cannot be tolerated, Pulse Width Modulation ( PWM ) should be used to control the dimming of an LED. In PWM operation, the forward current, If is kept constant, thus the wavelength will not shift. Brightness perceived by human eyes is directly proportional to the duty cycle ( D ) of the PWM signal ( Figure 9 ). For general application, the frequency of PWM should be greater than 200Hz, so that the human eyes would not be able to differentiate each on/off pulse, but integrating all the pulses as perceived brightness. The color ( dominant wavelength ) shift can be avoided by using PWM dimming. If tpulse t Duty cycle D = tpulse % T T Figure 8 Typical PWM signal - 3 -
4 Figure 9 LED dimming can be accomplished by adjusting the duty cycle of PWM signal Example: Dominant SPNova True Green LED, NPT-USS with luminous intensity grouping AE has a typical IV of 20cd at 350mA. If a customer need 10cd in their final application, they could do so by driving the LED with 5ms pulse on and 5ms pulse off with biased current stay at 350mA. This 50% duty cycle configuration will ensure the light output is 50% of the same DC current level without causing any wavelength shift. Figure 10 Typical PWM signal for duty cycle = 50% If the 50% dimming is achieved by reducing the forward current from 350mA to 175mA, the dominant wavelength will increase by approximate 4nm from 530nm to 534nm ( Fig. 11 ). This might cause visual detectable color shift. 175mA 350mA Figure 11 Dominant wavelength shift with forward current bias from 350mA to 175mA - 4 -
5 For application that requires full spectrum dimming, that is to adjust the light intensity from zero light output to maximum illumination, PWM dimming is the only design option. When using linear current dimming, and the LED forward current level falls below the minimum current density threshold of the LED chip, the LED might light up intermittently or on a multiple LEDs design, some LEDs might light up while the rest remain off. This will cause non-uniformity illumination on the application. The minimum current density threshold is depends on the chip size and the chip technology. PWM Dimming Circuit Design Most of the constant current LED drivers available in the market now are with built in function to allow PWM input. This simplifies the LED circuit design and allows a wide range of dimming ratio without impacting the color performance of the LED. Several example of PWM dimming circuit implementations are depicted in the figures below: Figure 12 A typical LED driving circuit using National Semiconductor LM2698 Boost regulator. The PWM signal is directly supply to the SHDN Pin of LM2698 to control dimming operation
6 Figure 13 LED circuit design suitable to drive Dominant 1W SPNova using Linear Technology LT3476. This LED driver is capable to drive 4 strings of LED and perform separate PWM dimming on each string. Figure 14 Another LED circuit design using Maxim MAX6970, 36V, 8 Channel Constant Current LED Driver. The PWM signal to perform LED dimming can be applied through the OE pin or direct input from a microcontroller
7 PWM Signal Generation There are 3 typical ways to generate PWM signal: 1. Microcontroller timer 3. LED driver with inbuilt PWM generator such as Maxim MAX16805 Out of the 3 above, the 555 timer solution provides the simplest and cost effective solution for PWM signal generation. PWM Signal Generation Using 555 Timer A simple circuit design to generate PWM signal is as depicted in Figure 15 below. This circuit design requires only a low cost, widely available 555 timer and 5 passive components. PWM signal pulse width is defined by the charging of capacitor C2 through resistor R1. While the duty cycle of PWM signal can be adjusted by the ratio of R1 and R2. The CV pin of 555 timer should be bypassed with a capacitor for noise reduction and false triggering prevention. The pulse width signal can be approximated by the equation below : Pulse on time = 0.69 X ( R1 X C2 ) = Pulse Width Pulse off time = 0.69 X ( R2 X C2 ) And thus the duty cycle can be calculated by the equation below : R1 PWM duty cycle = R1 + R2 By replacing R2 with a 15K Ohm potential meter, the duty cycle for the circuit below can be adjusted from ~5% up to 95%. This would provide sufficient dimming range for typical LED application
8 Figure 15 A typical PWM signal generation using NE555 Configuration: R1 = 270 Ohm, R2 = 5K Ohm, C2= 4.7uF Pulse Width ~ 1ms, duty cycle ~ 5% Configuration: R1 = 270 Ohm, R2 = 270 Ohm, C2= 4.7uF Pulse Width ~ 1ms, duty cycle ~ 50% Configuration: R1 = 270 Ohm, R2 = 27 Ohm, C2= 4.7uF Pulse Width ~ 1ms, duty cycle ~ 90% Figure 16 By adjusting the value of resistor R2, various duty cycle can be obtained - 8 -
9 Summary PWM is a better approach for dimming InGaN technology LED instead of linear current dimming. PWM dimming prevents unwanted color shift on LED while maintaining the required light intensity. With most of the LED driver ICs have inbuilt function for PWM input signal, the implementation of PWM dimming becomes very simple and do not require any extensive circuit design or extra circuit components
Pulse Width Modulation
Pulse Width Modulation Pulse width modulation (PWM) is a technique in which a series of digital pulses is used to control an analog circuit. The length and frequency of these pulses determines the total
Welcome to this presentation on Driving LEDs Resistors and Linear Drivers, part of OSRAM Opto Semiconductors LED Fundamentals series.
Welcome to this presentation on Driving LEDs Resistors and Linear Drivers, part of OSRAM Opto Semiconductors LED Fundamentals series. In this presentation we will look at: - Simple resistor based current
Spectral and Luminous Efficacy Change of High-power LEDs Under Different Dimming Methods
Spectral and Luminous Efficacy Change of High-power LEDs Under Different Dimming Methods Yimin Gu, Nadarajah Narendran, Tianming Dong and Huiying Wu Lighting Research Center Rensselaer Polytechnic Institute,
External Filter Requirements for Reducing DC Offset on the Analog Video Outputs of Telestream ClipMail Appliances
APPLICATION NOTE Introduction External Filter Requirements for Reducing DC Offset on the Analog Video Outputs of Telestream ClipMail Appliances This application note is for users of ClipMail Pro and older
DSM Series Ultra Thin Surface Mount Single Digit 7-Segment LED Display
DSM Series Ultra Thin Surface Mount Single Digit 7-Segment LED Display DSM7UA70105-0.70 (17.78mm) Digit Height Emitting Color: Pure Green (InGaN/GaN) Applications People Movers Home Appliances Medical
Application Note 5310
Driving High Power, High Brightness LEDs Application Note 5310 Introduction This paper describes the various methods of driving the high power and high brightness LED. The task of designing an LED based
Series AMLDL-Z Up to 1000mA LED Driver
FEATURES: Click on Series name for product info on aimtec.com Series Up to ma LED Driver Models Single output Model Input Voltage (V) Step Down DC/DC LED driver Operating Temperature range 4ºC to 85ºC
Notes. Astable and Monostable Multivibrator Trainer NV6507. Operating Manual Ver 1.1
Notes Astable and Monostable Multivibrator Trainer Operating Manual Ver 1.1 Nvis Technologies 20 141-B, Electronic Complex, Pardeshipura, Indore- 452 010 India Tel.: 91-731- 4211500 Email: info@nvistech.com
High Frequency True PWM Dimming White LED Driver MP3304 and MP3305
The Future of Analog IC Technology AN021 High Frequency True PWM Dimming White LED Driver MP3304 and MP3305 High Frequency True PWM Dimming White LED Driver MP3304 and MP3305 Prepared by Zhijun Ye and
Transistor Characteristics and Single Transistor Amplifier Sept. 8, 1997
Physics 623 Transistor Characteristics and Single Transistor Amplifier Sept. 8, 1997 1 Purpose To measure and understand the common emitter transistor characteristic curves. To use the base current gain
IC LM 3914 Design Note
IC LM 3914 Design Note 1 LED displays are necessary to indicate audio levels, measurements and even for ornamental purposes. The simplest way to design an LED display is the circuit around the popular
QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 994 THREE CHANNEL LED BALLASTER WITH PWM LT3003 DESCRIPTION
LT00 DESCRIPTION Demonstration circuit features the LT00 three channel LED ballaster with in a 0-lead MSOP thermally enhanced MSE package. The demonstration circuit is designed to ballast three channels
Experiment # (7) FSK Modulator
Islamic University of Gaza Faculty of Engineering Electrical Department Experiment # (7) FSK Modulator Digital Communications Lab. Prepared by: Eng. Mohammed K. Abu Foul Experiment Objectives: 1. To understand
Introduction to Light Emitting Diodes (LEDs)
Introduction to Light Emitting Diodes (LEDs) Introduction Light-emitting diodes (LEDs) are promising lighting sources for general lighting applications with the promise of being more than ten times as
36V 21.6 ~ 36V 4A 3A 2.5A 2A 1.7A 1.45A 1.3A 30V 18 ~ 30V 24V 14.4 ~ 24V. 60W 60W 60W 60W 61.2W 60.9W 62.4W 150mVp-p 17 ~ 22V.
IP65 IP67 s e ries SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note.2 150mVp-p VOLTAGE ADJ. RANGE Note.6
Hello and Welcome to this presentation on LED Basics. In this presentation we will look at a few topics in semiconductor lighting such as light
Hello and Welcome to this presentation on LED Basics. In this presentation we will look at a few topics in semiconductor lighting such as light generation from a semiconductor material, LED chip technology,
LUXEON III Star. power light source. Introduction
Technical Datasheet DS46 power light source LUXEON III Star Introduction LUXEON III is a revolutionary, energy efficient and ultra compact new light source, combining the lifetime and reliability advantages
HDSP-3530/-3730/-5530/
H Seven Segment Displays for High Light Ambient Conditions Technical Data HDSP-3530/-3730/-5530/ -3900 Series HDSP-4030/-4130/-5730/ -4200 Series Features High Light Output Typical Intensities of Up to
Auto Adjust & Dimming LED driver IC. Auto Adjust Voltage DC-DC Converter & Current Controller
Auto Adjust & Dimming LED driver IC Auto Adjust Voltage DC-DC Converter & Current Controller Features Use for high brightness LED lighting driving Supply voltage input range from 3V boost to 400V stepdown
Create Colorful and Bright LED Light with an LED Matrix Dimmer
Create Colorful and Bright LED Light with an LED Matrix Dimmer By Keith Szolusha, Applications Engineering Section Leader, Power Products, Linear Technology RGB LEDs are used in projector, architectural,
ENGR-4300 Electronic Instrumentation Quiz 4 Spring 2011 Name Section
ENGR-4300 Electronic Instrumentation Quiz 4 Spring 2011 Name Section Question I (20 points) Question II (20 points) Question III (20 points) Question IV (20 points) Question V (20 points) Total (100 points)
NBU-1012 Discharge circuit User Manual
rev 1.10/ 2012 03 29 NBU-1012 Discharge circuit User Manual Overview / Applications Cooling NBU-1012 discharge circuit is designed for simplification of solid-state laser systems development. Module forms
Physics 623 Transistor Characteristics and Single Transistor Amplifier Sept. 13, 2006
Physics 623 Transistor Characteristics and Single Transistor Amplifier Sept. 13, 2006 1 Purpose To measure and understand the common emitter transistor characteristic curves. To use the base current gain
1. Learn about the 555 timer integrated circuit and applications 2. Apply the 555 timer to build an infrared (IR) transmitter and receiver
Electronics Exercise 2: The 555 Timer and its Applications Mechatronics Instructional Laboratory Woodruff School of Mechanical Engineering Georgia Institute of Technology Lab Director: I. Charles Ume,
TCS230 PROGRAMMABLE COLOR LIGHT TO FREQUENCY CONVERTER TAOS046 - FEBRUARY 2003
High-Resolution Conversion of Light Intensity to Frequency Programmable Color and Full-Scale Output Frequency Communicates Directly With a Microcontroller Single-Supply Operation (2.7 V to 5.5 V) Power
LABORATORY EXPERIMENT. Infrared Transmitter/Receiver
LABORATORY EXPERIMENT Infrared Transmitter/Receiver (Note to Teaching Assistant: The week before this experiment is performed, place students into groups of two and assign each group a specific frequency
Tamura Open Loop Hall Effect Current Sensors
Tamura Open Loop Hall Effect Current Sensors AC, DC, & Complex Currents Galvanic Isolation Fast Response 50kHz small signal frequency bandwidth Quality & Reliability RoHs compliance Overview The following
1ED Compact A new high performance, cost efficient, high voltage gate driver IC family
1ED Compact A new high performance, cost efficient, high voltage gate driver IC family Heiko Rettinger, Infineon Technologies AG, Am Campeon 1-12, 85579 Neubiberg, Germany, heiko.rettinger@infineon.com
A Lesson on Digital Clocks, One Shots and Counters
A Lesson on Digital Clocks, One Shots and Counters Topics Clocks & Oscillators LM 555 Timer IC Crystal Oscillators Selection of Variable Resistors Schmitt Gates Power-On Reset Circuits One Shots Counters
Discontinued. LUXEON V Portable. power light source. Introduction
Preliminary Technical Datasheet DS40 power light source LUXEON V Portable Introduction LUXEON is a revolutionary, energy efficient and ultra compact new light source, combining the lifetime and reliability
1W High Power Purple LED Technical Data Sheet. Part No.: LL-HP60MUVA
1W High Power Purple LED Technical Data Sheet Part No.: LL-HP60MUVA Spec No.: HP60M Rev No.: V.2 Date: Aug./18/2009 Page: 1 OF 8 Features: Luckylight High power LED type. Lead frame type package (Heat
A Lesson on Digital Clocks, One Shots and Counters
A Lesson on Digital Clocks, One Shots and Counters Topics Clocks & Oscillators LM 555 Timer IC Crystal Oscillators Selection of Variable Resistors Schmitt Gates Power-On Reset Circuits One Shots Counters
AN10579. Driving LED light bars using NXP solutions. Document information
ev. 01 1 February 2007 Application note Document information Info Keywords Abstract Content LED, LED controller, I2C, light bar,, color mixing, architectural lighting, LED lighting, LED driver, PWM, STAplug+,
1-Watt SMD 6mm With Dome Lens
1-Watt SMD 6mm With Dome Lens x Robust energy-efficient design with long operating life x Low thermal resistance x Exceptional spatial uniformity x Optional optics suit application x Available in yellow,
SEMICONDUCTOR FC Pin Switch-Mode LED Lamp Driver IC FC9921 TECHNICAL DATA
SEMICONDUCTOR TECHNICAL DATA FC99 3-Pin Switch-Mode LED Lamp Driver IC Features Constant output current: 0mA Universal 85-65VAC operation Fixed off-time buck converter Internal 475V power MOSFET Applications
Luminous flux emitted by LED depends directly on forward current (I f. is LED forward voltage (voltage drop) at nominal I f
4. ED COTROS 4.1. Cold lumens versus hot lumens uminous flux emitted by ED depends directly on forward current (I f ) magnitude. Typical luminous flux for nominal I f (e.g. 350 ma) is listed in datasheets.
GT Sensors Precision Gear Tooth and Encoder Sensors
GT Sensors Precision Gear Tooth and Encoder Sensors NVE s GT Sensor products are based on a Low Hysteresis GMR sensor material and are designed for use in industrial speed applications where magnetic detection
LAB 7 MOSFET CHARACTERISTICS AND APPLICATIONS
LAB 7 MOSFET CHARACTERISTICS AND APPLICATIONS Objective In this experiment you will study the i-v characteristics of an MOS transistor. You will use the MOSFET as a variable resistor and as a switch. BACKGROUND
A whole new way to design backlight inverters for mobile computing applications
A whole new way to design backlight inverters for mobile computing applications John Lambert Product Marketing Engineer International Rectifier Inc. Carl Smith Product Marketing Engineer International
AS Systems & Control Study Notes Part 2: Electronic Materials. E.Clarvis Conductors. Materials
Part 1 Learning Objectives Know the properties of Semiconductors. Know the properties and functions of: Resistors s Materials There are three main types of materials used in electronic and electrical systems:
Reliability Data. Introduction. Index. Reliability Datasheet RD07
Reliability Datasheet RD07 LUXEON Rebel Reliability Data Introduction This reliability datasheet summarizes the reliability performance of LUXEON Rebel. Overall product reliability depends on the customer's
OPTICAL COMMUNICATION BASED STEPPER MOTOR CONTROL USING PULSE WIDTH MODULATION
2011 pp 1-5 OPTICAL COMMUNICATION BASED STEPPER MOTOR CONTROL USING PULSE WIDTH MODULATION Vinayak Abrol* Department of Electronics & Communication, SSGPURC Panjab University Chandigarh, India Votrix13@gmail.com
Brake Intensity Advisory System
Brake Intensity Advisory System ECE 4007 Senior Design Project Project Advisor Dr. Linda Milor Caleb Trotter Ed Yri Jace Hall Michael Purvis Table of Contents Executive Summary iii 1. Introduction...1
RGB Wall Washer Using ILD4035
ILD4035 Application Note AN216 Revision: 1.0 Date: RF and Protection Devices Edition Published by Infineon Technologies AG 81726 Munich, Germany 2010 Infineon Technologies AG All Rights Reserved. Legal
NM-AN04 Position Control using NanoMuscle Actuators Rev March 2003 Applicable NanoMuscle Families: RS Rotary and NM Commercial
NM-AN0 Position Control using Actuators Rev. 9 March 00 Applicable Families: RS Rotary and NM Commercial Application Note In their standard form all actuators can provide simple full-range motion by simply
An introduction to electronic components that you will need to build a motor speed controller.
An introduction to electronic components that you will need to build a motor speed controller. Resistors A resistor impedes the flow of electricity through a circuit. Resistors have a set value. Since
Time resolved photoluminescence studies of blue light-emitting diodes (LED)
APPLICATION NOTE Time resolved photoluminescence studies of blue light-emitting diodes (LED) WITec GmbH, Lise-Meitner-Str. 6, 89081 Ulm, Germany fon +49 (0) 731 140 700, fax +49 (0) 731 140 70 200 info@witec.de,
Display Board Pulse Width Modulation (PWM) Power/Speed Controller Module
Display Board Pulse Width Modulation (PWM) Power/Speed Controller Module RS0 Microcontroller LEDs Motor Control Pushbuttons Purpose: To demonstrate an easy way of using a Freescale RS0K2 microcontroller
High-power LEDs promise a
by Keith Szolusha Linear Technology Corporation SELECTING OPTIMUM DRIVERS FOR MAXIMIZING SOLID-STATE LED LIGHTING PERFORMANCE Automobile manufacturers are increasingly taking advantage of the latest technologies
LDS8720. 184 WLED Matrix Driver with Boost Converter FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
184 WLED Matrix Driver with Boost Converter FEATURES High efficiency boost converter with the input voltage range from 2.7 to 5.5 V No external Schottky Required (Internal synchronous rectifier) 250 mv
Lab 3. Transistor and Logic Gates
Lab 3. Transistor and Logic Gates Laboratory Instruction Today you will learn how to use a transistor to amplify a small AC signal as well as using it as a switch to construct digital logic circuits. Introduction
Welcome to this presentation on Switch Mode Drivers, part of OSRAM Opto Semiconductors LED Fundamentals series. In this presentation we will look at:
Welcome to this presentation on Switch Mode Drivers, part of OSRAM Opto Semiconductors LED Fundamentals series. In this presentation we will look at: How switch mode drivers work, switch mode driver topologies,
Driving LEDs with a PIC Microcontroller Application Note
Driving LEDs with a PIC Microcontroller Application Note Introduction Nowadays, applications increasingly make use of LEDs as a replacement for traditional light bulbs. For example, LEDs are frequently
MAS.836 HOW TO BIAS AN OP-AMP
MAS.836 HOW TO BIAS AN OP-AMP Op-Amp Circuits: Bias, in an electronic circuit, describes the steady state operating characteristics with no signal being applied. In an op-amp circuit, the operating characteristic
555 Timers. We are going to look at using the 555 to create two very different types of timer. A MONOSTABLE timer and an ASTABLE timer.
555 Timers We are now going to concentrate on specific IC s and how they can be used to perform useful functions. In turn we shall be looking at Timers, Amplifiers, Counters, Microprocessors and finally
AS2815. 1.5A Low Dropout Voltage Regulator Adjustable & Fixed Output, Fast Response
1.5A Low Dropout oltage Regulator Adjustable & Fixed Output, Fast Response FEATURES Adjustable Output Down To 1.2 Fixed Output oltages 1.5, 2.5, 3.3, 5.0 Output Current of 1.5A Low Dropout oltage 1.1 Typ.
The 555 timer: Waveform shaping
The 555 timer: Waveform shaping Introduction: Oscillators are ubiquitous not only in research environments but also in our modern, technology-oriented society. Oscillators are used for communication, timing
HLCP-J100, HDSP-4820, HDSP-4830 & HDSP-4832 10-Element Bar Graph Array. Features
HLCP-J, HDSP-, HDSP- & HDSP- -Element Bar Graph Array Data Sheet Description These -element LED arrays are designed to display information in easily recognizable bar graph form. The packages are end stackable
11: AUDIO AMPLIFIER I. INTRODUCTION
11: AUDIO AMPLIFIER I. INTRODUCTION The properties of an amplifying circuit using an op-amp depend primarily on the characteristics of the feedback network rather than on those of the op-amp itself. A
Printed Circuit Board Layout and Probing for GaN Power Switches
Printed Circuit Board Layout and Probing for GaN Power Switches Transphorm, Inc Zan Huang, Felix Recht and Yifeng Wu Application Note AN-0003 This document describes best practices for printed circuit
7-41 POWER FACTOR CORRECTION
POWER FTOR CORRECTION INTRODUCTION Modern electronic equipment can create noise that will cause problems with other equipment on the same supply system. To reduce system disturbances it is therefore essential
Pulse Width Modulation (PWM) LED Dimmer Circuit. Using a 555 Timer Chip
Pulse Width Modulation (PWM) LED Dimmer Circuit Using a 555 Timer Chip Goals of Experiment Demonstrate the operation of a simple PWM circuit that can be used to adjust the intensity of a green LED by varying
Advanced LED Controller (LED Chaser)
Advanced LED Controller (LED Chaser) Introduction. Advanced LED controller (also known as LED Chaser) is microcontroller based circuit designed to produce various visual LED light effects by controlling
LUXEON Rebel. Phosphor-Converted (PC) Amber
LUXEON Rebel PC Amber High flux and color stability Technical Datasheet DS62 LUXEON Rebel Phosphor-Converted (PC) Amber Introduction LUXEON Rebel Phosphor-Converted (PC) Amber is an ultra-compact, surface-mount,
HL1606. HL1606 is a LED driver IC with SPI controlled. We can get complex mode changes by fewer data. No. Name Description No.
HL1606 DESCRIPTION HL1606 is a LED driver IC with SPI controlled. We can get complex mode changes by fewer data. FEATURES NMOS output SPI controlled,plus synchronization speed control port: S-I PWM output,frequency:500hz
LM1036 Dual DC Operated Tone/Volume/Balance Circuit
LM1036 Dual DC Operated Tone/Volume/Balance Circuit General Description The LM1036 is a DC controlled tone (bass/treble), volume and balance circuit for stereo applications in car radio, TV and audio systems.
Efficient and reliable operation of LED lighting is dependent on the right choice of current-limiting resistor
Efficient and reliable operation of LED lighting is dependent on the right choice of current-limiting resistor Phil Ebbert, VP of Engineering, Riedon Inc. Introduction Not all resistors are the same and
Design of OSC and Ramp Generator block for Boost Switching Regulator
Analog IC Design Contest 2011 Navis Team Hanoi University of Science and Technology Design of OSC and Ramp Generator block for Boost Switching Regulator Final Report Students: Advisors: Pham Van Danh (senior
Yrd. Doç. Dr. Aytaç Gören
H2 - AC to DC Yrd. Doç. Dr. Aytaç Gören ELK 2018 - Contents W01 Basic Concepts in Electronics W02 AC to DC Conversion W03 Analysis of DC Circuits W04 Transistors and Applications (H-Bridge) W05 Op Amps
ETEC 421 - Digital Controls PIC Lab 10 Pulse Width Modulation
ETEC 421 - Digital Controls PIC Lab 10 Pulse Width Modulation Program Definition: Write a program to control the speed of a dc motor using pulse width modulation. Discussion: The speed of a dc motor is
QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 923 DUAL STEP-DOWN 1.5A LED DRIVER LT3475 DESCRIPTION
QUICK STA GUIDE FOR DEMONSTRATION CIRCUIT 923 DUAL STEP-DOWN LED DRIVER LT3475 DESCRIPTION Demonstration circuit 923 features the LT 3475 dual step-down LED driver in a 16-lead TSSOP thermally enhanced
AN1991. Audio decibel level detector with meter driver
Rev. 2.1 20 March 2015 Application note Document information Info Keywords Abstract Content SA604A, LM358, RSSI, cellular radio The SA604A can provide a logarithmic response proportional to the input signal
Basic Pulse Width Modulation
EAS 199 Fall 211 Basic Pulse Width Modulation Gerald Recktenwald v: September 16, 211 gerry@me.pdx.edu 1 Basic PWM Properties Pulse Width Modulation or PWM is a technique for supplying electrical power
Data Sheet. Nationstar LED
Data Sheet Nationstar LED 1 Table of Contents General Informations:... 3 Electrical and Flux Characteristics... 3 Color Wavelength Diagram:... 6 Mechanical Dimensions:... 7 Electrical Connection:... 7
Circuit Components Lesson Amplifier Fundamentals The role of a amplifier is to produce an output which is an enlarged reproduction of the
4.1 Amplifier Fundamentals The role of a amplifier is to produce an output which is an enlarged reproduction of the features of the signal fed into the input. The increase in signal by an amplifier is
Welcome to this presentation on Driving LEDs AC-DC Power Supplies, part of OSRAM Opto Semiconductors LED Fundamentals series. In this presentation we
Welcome to this presentation on Driving LEDs AC-DC Power Supplies, part of OSRAM Opto Semiconductors LED Fundamentals series. In this presentation we will look at: - the typical circuit structure of AC-DC
Fundamentals of Signature Analysis
Fundamentals of Signature Analysis An In-depth Overview of Power-off Testing Using Analog Signature Analysis www.huntron.com 1 www.huntron.com 2 Table of Contents SECTION 1. INTRODUCTION... 7 PURPOSE...
How to Read a Datasheet
How to Read a Datasheet Prepared for the WIMS outreach program 5/6/02, D. Grover In order to use a PIC microcontroller, a flip-flop, a photodetector, or practically any electronic device, you need to consult
LED Lighting. Definitions and Characteristics. TND328/D Rev.1 Sep07
LED Lighting Definitions and Characteristics Definitions 2 Luminous Flux [lm] Luminous flux is the quantity of the energy of the light emitted per second in all directions. The unit of luminous flux is
Theory of Operation. Figure 1 illustrates a fan motor circuit used in an automobile application. The TPIC2101. 27.4 kω AREF.
In many applications, a key design goal is to minimize variations in power delivered to a load as the supply voltage varies. This application brief describes a simple DC brush motor control circuit using
MAGX L00 MAGX L0S
Features GaN depletion mode HEMT microwave transistor Internally matched Common source configuration Broadband Class AB operation RoHS Compliant +50V Typical Operation MTTF of 114 years (Channel Temperature
Microwave Transistor Bias Considerations. Application Note 944-1
Microwave Transistor Bias Considerations Application Note 944-1 Introduction Often the least considered factor in microwave transistor circuit design is the bias network. Considerable effort is spent in
ENEE 307 Electronic Circuit Design Laboratory Spring 2012. A. Iliadis Electrical Engineering Department University of Maryland College Park MD 20742
1.1. Differential Amplifiers ENEE 307 Electronic Circuit Design Laboratory Spring 2012 A. Iliadis Electrical Engineering Department University of Maryland College Park MD 20742 Differential Amplifiers
DW8501 High Power LED Driver
Descriptions The is an instant On/Off LED driver for high power LED applications. At output stage, one regulated current port is designed to provide a uniform and constant current sink for driving LEDs
Balun Parameter Definitions & Measurement May 2004
Balun Parameter Definitions & Measurement May 2004 Differential circuits are becoming more widely used in RF circuits for the same reason that they have been used for years in lower frequency circuits.
Intelligent Over Temperature Protection for LED Lighting Applications
Intelligent Over Temperature Protection for LED Lighting Applications Authors: Hakan Yilmazer, Bernd Pflaum www.infineon.com Abstract LED lighting is becoming increasingly popular. It offers numerous advantages
SSPI-APPN OTES: PARALLEL C ONNECTIONS
There are two distinct reasons to connect power supplies in parallel: Current Sharing and Redundancy. Combining of these reasons is common, and there are many ways to implement them. The unique considerations
Getting to Know LEDs, Applications and Solutions
Getting to Know LEDs, Applications and Solutions Light-Emitting Diodes (LEDs) are a reliable means of indication compared to light sources such as incandescent and neon lamps. LEDs are solid-state devices
Stepper Motor Driver (74194)
Stepper Motor Driver (74194) This page features an inexpensive stepper motor driver that could be used to power slow speed projects on the layout or other hobby applications. Based on the SN74LS194 - Bidirectional
Features. Applications
LM555 Timer General Description The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the
Designing interface electronics for zirconium dioxide oxygen sensors of the XYA series
1 CIRCUIT DESIGN If not using one of First Sensors ZBXYA interface boards for sensor control and conditioning, this section describes the basic building blocks required to create an interface circuit Before
DEALING WITH AC MAINS
ARTICLE DEALING WITH AC MAINS D.MOHAN KUMAR One of the major problem that is to be solved in an electronic circuit design is the production of low voltage DC power supply from AC mains to power the circuit.
Powering Integrated Circuits (ICs), and managing ripple voltage as it relates
Ripple Voltage & ESR Powering Integrated Circuits (ICs), and managing ripple voltage as it relates to ESR of capacitors Low voltage ICs require supply voltage (Vcc) to have reduced levels of ripple voltage
Peggy Alavi Application Engineer September 3, 2003
Op-Amp Basics Peggy Alavi Application Engineer September 3, 2003 Op-Amp Basics Part 1 Op-Amp Basics Why op-amps Op-amp block diagram Input modes of Op-Amps Loop Configurations Negative Feedback Gain Bandwidth
LLS Series LED Light Sources Installation and Operation Instructions
LLS Series LED Light Sources Installation and Operation Instructions Description Ocean Optics LED Series light sources (LLS) are engineered to be a versatile tool for scientific and general lighting applications.
Tire pressure monitoring
Application Note AN601 Tire pressure monitoring 1 Purpose This document is intended to give hints on how to use the Intersema pressure sensors in a low cost tire pressure monitoring system (TPMS). 2 Introduction
Reliability Data. LUXEON Rebel. Introduction. Index. Reliability Datasheet RD07
Reliability Datasheet RD7 LUXEON Rebel Reliability Data Introduction This reliability datasheet summarizes the reliability performance of LUXEON Rebel. Overall product reliability depends on the customer's
Absolute Maximum Ratings
RC15 Voltage-to-Frequency Converters www.fairchildsemi.com Features Single supply operation Pulse output DTL/TTL/CMOS compatible Programmable scale factor (K) High noise rejection Inherent monotonicity
Kit 106. 50 Watt Audio Amplifier
Kit 106 50 Watt Audio Amplifier T his kit is based on an amazing IC amplifier module from ST Electronics, the TDA7294 It is intended for use as a high quality audio class AB amplifier in hi-fi applications
Harvatek Surface Mount CHIP LED Data Sheet HT-380FCH-ZZZZ
Harvatek Surface Mount CHIP LED Data Sheet Official Product HT Part No. Customer Part No. Data Sheet No. Tentative Product **************** **************** May. 14, 2007 Version of 1.1 Page 1/15 DISCLAIMER...