SeaStar steering parts

Transcription

1 Helms: SeaStar steering parts SEASTAR/HYNAUTIC helm parts BayStar HELM SEAL KIT BAYSTAR (HS17) Replacement shaft seal kit for BayStar helms only. Contains three screws, shaft seal and o-ring. (See Items 3, and in illustration.) HELM SEAL KIT BAYSTAR PLUS (HS176) Replacement shaft seal kit for BayStar PLUS helms. VENTED FILL PLUG (31660) Comes with every BayStar helm. Use on BayStar helms only. (See Item 1 in illustration.) SeaStar & SeaStar PRO HELM SEAL KIT (VARIES) Replacement shaft seal kits for SeaStar 1., 1.7 (I),.0,. (II), Pro, P.S. and Hynautic helms can vary by model of helm. Please see helm seal kit chart on next page. VENTED FILL PLUG (HA31) Comes with every SeaStar helm. Must be used in all single steering station systems or on uppermost helm in multiple steering stations. BACK MOUNT PLATE (07) Round plate used behind BayStar helm for dash mounting. (See Item in illustration.) NOTE: ITEMS FOR SECOND HELM STATION APPLICATIONS ARE NOT FOR USE WITH SEASTAR PRO HELMS. HA31 VENTED FILL PLUG NON-VENTED FILL PLUG (HA3) For use on lower station in multi-station systems only. Included with kits HF01 and HF0. OUTBOARD ADD-A-STATION/AUTOPILOT KIT (HF01) Contains fi ttings for adding either a steering station or an autopilot to an existing SeaStar outboard steering system. Includes feet of SeaStar 3/8" nylon tubing and non-vented fi ll plug for helm at upper most station. STERN DRIVE ADD-A-STATION/AUTOPILOT KIT (HF0) Contains fi ttings for adding a steering station or autopilot to existing SeaStar stern drive steering system. Allows use of SeaStar nylon tubing (with SeaStar 1.7 helms only). Includes non-vented fi ll plug for lower station helm. HA3 NON-VENTED FILL PLUG NOTE: Appearance may vary from drawing. This is a solid plug (no vent feature is visible when viewed from bottom of threaded portion). HF01 HF0 STEERING WHEEL SHAFT NUT (771) Nylock lock nut to attach steering wheel to helm shaft, for all SeaStar helms. (Included with all SeaStar helms.)

2 hydraulic steering service parts: helms and helm fi ttings SeaStar/BayStar/Capilano/Hynautic Helm Seal Kits: HELM SEAL HELM PART KIT DESCRIPTION NUMBER P/N BAYSTAR HELM CAPILANO HELM BAYSTAR - FRONT MOUNT HH016 HS17 BAYSTAR - SPORT TILT HH01 HS17 BAYSTAR PLUS - FRONT MOUNT HH1 HS176* 1 BAYSTAR PLUS - SPORT TILT HH13 HS176* 1 CAPILANO 10V HH0 HS160 CAPILANO 17V HH7 HS160 HYNAUTIC H-0 (3/ SHAFT) H-6 HS-01/0* HYNAUTIC H-0 (3/ SHAFT) H- HS-01/0* HYNAUTIC H-0 (1 SHAFT) H-1 HS-01/0* HYNAUTIC H-0 (3/ SHAFT) H--0 HS-03/0* 3 HYNAUTIC H-0 (1 SHAFT) H- HS-03/0* 3 HYNAUTIC H-0 (3/ SHAFT) H-1-0 HS-03/0* 3 HYNAUTIC H-0 (1 SHAFT) H-1 HS-0 SEASTAR 1. - FRONT MOUNT HH69 HS176 SEASTAR 1. - REAR MOUNT HH60 HS176* 1 SEASTAR 1. - R. MT FULL FEEDBACK HH31 HS176 SEASTAR 1. - R. MT. 1 STRT. SHAFT HH79 HS11 SEASTAR 1. - R. MT. 1 TAPER. SHAFT HH80 HS11 SEASTAR 1. - TILT HH7 HS176 SEASTAR FRONT MOUNT HH71 HS176* 1 SEASTAR FRONT MT. COMMERCIAL HH17 HS176* 1 SEASTAR FT. MT. FULL FEEDBACK HH761 HS176 SEASTAR REAR MOUNT HH61 HS176* 1 SEASTAR R. MT. 1 TAPER. SHAFT HH81 HS11 SEASTAR SPORT TILT HH91 HS176* 1 SEASTAR TRADITIONAL TILT HH71 HS176* 1 SEASTAR.0 - FRONT MOUNT HH73 HS176* 1 SEASTAR.0 - FT. MT. FULL FEEDBACK HH760 HS176 SEASTAR.0 - SPORT TILT HH7 HS176* 1 SEASTAR.0 - TRADITIONAL TILT HH73 HS176* 1 SEASTAR. - FRONT MOUNT HH7 HS176* 1 SEASTAR. - FRONT MT. COMMERCIAL HH HS176* 1 SEASTAR. - FT. MT. FULL FEEDBACK HH76 HS176 SEASTAR. - REAR MOUNT HH6 HS176* 1 SEASTAR. - R. MT. 1 TAPER. SHAFT HH8 HS11 SEASTAR. - SPORT TILT HH9 HS176* 1 SEASTAR. -TRADITIONAL TILT HH7 HS176* 1 SEASTAR PRO 1. - TRADITIONAL TILT* HH77 HS176 SEASTAR PRO FRONT MOUNT* HH779 HS176 SEASTAR PRO FT. MT. COMMERCIAL* HH18 HS176 SEASTAR PRO REAR MOUNT* HH778 HS176 SEASTAR PRO SPORT TILT* HH89 HS176 SEASTAR PRO TRADITIONAL TILT* HH773 HS176 SEASTAR PRO.0 - FRONT MOUNT* HH770 HS176 SEASTAR PRO.0 - REAR MOUNT* HH771 HS176 SEASTAR PRO.0 - SPORT TILT* HH90 HS176 SEASTAR PRO.0 - TRADITIONAL TILT* HH77 HS176 SEASTAR PRO. - FRONT MOUNT HH77 HS176 HYNAUTIC H-1/H-/H-6 HELMS SEASTAR & BAYSTAR PLUS FRONT MOUNT HELM SEASTAR SPORT TILT MECH A NISM & HELM SEASTAR TRADITIONAL TILT MECH A NISM & HELM HYNAUTIC H-/H-1 HELMS SEASTAR REAR MOUNT HELM PLEASE NOTE: SEASTAR POWER STEERING HELMS ARE USUALLY STANDARD VERSIONS OF SEASTAR HELMS. REFER TO THAT HELM FOR SERVICE PARTS INFORMATION. SEAL KITS FOR HYNAUTIC RESERVOIRS: RS-01: R-/R-0, R-10, R-13, R-1 models. SEAL KITS FOR OBSOLETE HYNAUTIC HELMS: HS-0: H-0 series helms. HS-06: H-60 series helms. HS-08: H-80 series helms, before date code HS-09: H-80 series helms, after date code HS-10: H-100 & H-00 series helm pumps. SEASTAR/HYNAUTIC helm parts * SeaStar PRO helms cannot be used with an unbalanced cylinder and require use of SeaStar PRO Kevlar reinforced outboard hose. *1 SeaStar helm pumps manufactured from 198 through 1990 require Seal Kit # HS11 or Individual Shaft Seal #30. * H-0 and H-30 helms produced in 1978 and earlier use Seal Kit #HS date H-0 and H-30 helms use Seal Kit # HS-0. *3 H-0 helms produced in 1978 and earlier use Seal Kit #HS date H-0 Helms use Seal Kit # HS-0. 19

3 Fitting Kits: SeaStar steering parts (HF68) Kit to connect 1/ diameter copper tubing to SeaStar cylinders. SEASTAR/HYNAUTIC fitting kits SeaStar (HF07) Connects 3/8 diameter copper tubing to SeaStar cylinders (using 3/8 diameter nylon tubing). (HF08) Kit to connect 3/8 diameter copper tubing to SeaStar cylinders (using SeaStar outboard hose). (HF1) 3/ bulkhead fi tting kit for single cylinder installations. Two assemblies per kit. (HF13) 3 bulkhead fi tting kit for single cylinder installations. Two assemblies per kit. (HF1) 3/ bulkhead fi tting kit for dual cylinder installations. (HF1) 3 bulkhead fi tting kit for dual cylinder installations. (HF69) Kit to connect /8 diameter copper tubing to SeaStar cylinders. (HF81) degree fl are fi tting connection kit for SeaStar Systems. (HF8) Add a station or autopilot kit using 3/8 or degree fl are fi ttings. Hynautic H-0 HELM FITTINGS KIT FOR STATION 1 (HF-10) Contains 3/8 port & starboard fi ttings and 1/ return fi ttings. Requires the use of copper tubing. H-0 HELM FITTINGS KIT FOR STATION (HF-11) Contains 3/8 port & starboard fi ttings and 1/ return fi ttings. Requires the use of copper tubing. H-0 HELM FITTINGS KIT FOR STATION 1 (HF-1) Contains 1/ port & starboard fi ttings and 3/8 return fi ttings. Requires the use of copper tubing. Servicing SyTen Hydraulic Steering: H-0 HELM FITTINGS KIT FOR STATION (HF-) Contains 1/ port & starboard fi ttings and 3/8 return fi ttings. Requires the use of copper tubing. 10 NOTICE: The SyTen components were produced up until late 198 when they were replaced by the SeaStar steering systems. Telefl ex Canada no longer stocks any replacement part, fi ttings or seal kits for this steering system or any component of this system. Replacing or upgrading a SyTen inboard steering system to SeaStar components: Helms: The SyTen helm pump should be replaced with the current model SeaStar Helm Pump HH71 and Back Mount Kit HA18. This should be done at each helm station. Tube: The /16 nylon tube and fi ttings are obsolete and must be replaced with SeaStar 3/8 nylon extruded tube for all inboard applications. Uniflow Valve: U-10 or Model 0: Obsolete. No replacement parts are available. Cylinder: Adapter HA is required for the conversion from a SyTen steering cylinder to the use of a current SeaStar Steering cylinder.

4 hydraulic steering service parts: fi ttings & cylinder seal kits SeaStar/BayStar/Capilano/Hynautic Cylinder Seals: CYLINDER SEAL PART KIT CYLINDER MODEL NUMBER P/N BAYSTAR UNITS: COMPACT FRONT MOUNT HC6/67/68/68 HP600 OLD STYLE HC600 HP607 + HP608 CAPILANO INBOARD UNITS: BA10-7 (TMB/TMC) HC39/HC3 HS18 BA17-7 (TMB/TMC) HC30/HC36 HS183 BA-17-9TMB HC373 HS183 BA00-7 (TMB/TMC) HC31/HC37 HS18 BA00-11 (TMB/TMC) HC378/HC379 HS18 HYNAUTIC INBOARD UNITS (USED IN SEASTAR, CAPILANO & HYNAUTIC SYSTEMS): Hynautic Ball Joint Mount K-18 KS-0 Hynautic Ball Joint Mount K-19 KS-0 Hynautic Fixed Mount K- KS-0 Hynautic Fixed Mount K-7 KS-0 Hynautic Universal Mount K- KS-1 Hynautic Pivot Mount K-31 KS-0 Hynautic Universal Mount K-8 KS-18 Hynautic Universal Mount K-9 KS-18 SEASTAR INBOARD UNITS: BA1-6.ATM HC311 HS1 BA1-7ATM HC31 HS1 BA13-7ATM HC313 HS1 BA10-7ATM HC31 HS16 BA10-7TM HC318 HS18 BA10-9TM HC369 HS18 BA17-7TM HC319 HS183 SEASTAR INBOARD POWER STEERING UNITS: BA00 HC801/80/803/80 HS198 BA0 HC80/HC806 N/A at this time SEASTAR & HYNAUTIC STERN DRIVE UNITS: BA10-7EM HC36 HS16 BA13-8EM HC37 HS1 1-8EM HC38 HS1 1-8VEM HC39 HS1 9-VPS HC331 HS13 BA-1-EMV HC330 HS1 BA-13-7EM HC33 HS1 Hynautic Universal Mount K- KS-1 SEASTAR OUTBOARD UNITS: PIVOT FRONT MOUNT HC3/37/38/38 HS17 PIVOT FRONT MOUNT (PRO) HC63/637/638/638 N/A at this time CATAMARAN O/B (FIXED MOUNT) HC33 HS17 CATAMARAN O/B (FIXED MOUNT) HC37 KS-06 SIDE MOUNT HC370 HS13 SPLASHWELL MOUNT HC380 HS1 FRONT MT.-STD. (OBS.) HC30/HC3 HS17 FRONT MT.-COMPACT (OBS.) HC36 HS17 SEASTAR JET DRIVE UNITS: BA1-3ATM HC303 HS1 SEAL KIT REFERENCE FOR HYNAUTIC CYLINDERS: KS-01: K-11 through K-17 KS-0: K-18 through K-0 KS-03: K-, H1010 (old style) KS-0: K-1 through K-9 (before August, 1983) KS-0: K-31 through K-33 KS-06: K-1 through K-9 (after August, 1983) KS-07: K-10 KS-08: K-7 KS-09: K-8 & K-9 (before April 1, 198) KS-11: K-1, PSK-10 KS-1: K- (newer style) KS-13: K-3, K-0, PSK-11/PSK-1 (before April 1, 198) KS-1: K-1 KS-1: K-/K--B KS-17: K-3, K-, PSK-11/PSK-1 (after April 1, 198) KS-18: K-8 & K-9 (after April 1, 198) KS-19: K-6 11

5 BAYSTAR/SEASTAR/ cylinder parts Cylinders: Outboard BayStar Cylinder HC6 (HC6, HC67, HC68, HC68) SERVICE PARTS Socket Head Screw - Bracket 900 Locknut Washer Gland End/Bracket, Right Side Gland End/Bracket, Left Side Seal Gland Assembly Guide Tool Nut - Support Rod BayStar Cylinder HC600 GLAND KIT 'A' (HP607) INCLUDES ITEMS #1-6 IN ILLUSTRATION, AS FOLLOWS: #1, Wiper (Qty. 1); #, 1000 Shaft Seal (Qty. 1); #3, O-Ring (Qty. 1); #, 1300 Grommet (Qty. 1); #, Retainer Strip (Qty. 1); #6, 1100 End Gland (Qty. 1). GLAND KIT 'B' (HP608) INCLUDES ITEMS #7-1 IN ILLUSTRATION, AS FOLLOWS: #7, Wiper Seal (Qty. 1); #8, 1000 Shaft Seal (Qty. 1); #9, O-Ring (Qty. 1); #10, 1300 Grommet (Qty. 1); #11, Retainer Strip (Qty. 1); #1, 060 Washer, Delrin (Qty. ). SeaStar steering parts HC6 Compact Cylinder HC600 Old Style HP607 (1-6) HP608 (7-1) HS17 (B, C, D) (HC3 shown) SeaStar Front Mount Parts FRONT MOUNT CYLINDER SEAL KIT (HS17) Replacement front seal for kit for SeaStar pivot/front mount cyl in ders except PRO models. (For: HC3/HC37/HC38/HC38/HC33/ HC30/HC3/HC36). Includes seal glands, pin wrench and guide tool. Available separately: (B) Seal Gland (P/N 71), (C) Seal Gland Assembly Guide Tool (P/N 790), (D) Pin Wrench (P/N 7). (Includes items B, C & D in illustration.) HF0 (E) HF8 (E) (F) (HC3/HC30 shown) FRONT MOUNT CYLINDER ELBOW FITTING (600601) Elbow fi tting for HC3/HC37/HC38/ HC38 SeaStar front mount cylinder. (Item F in illustration). HF0 (E) 1 FRONT MOUNT CYLINDER BLEED FITTING (HF8) (was 88980) bleed fi ttings, O-rings and soft caps for HC3/HC37/HC38/ HC38 SeaStar front mount cylinders. (Item E in illustration, caps not shown.) (HC36 shown)

6 hydraulic steering service parts: outboard cylinders CYLINDER BLEEDER TEE FITTING SET (HF0) Pair of P/N 0960 bleeder tee fi ttings for olderstyle standard and compact SeaStar front mount cylinders (HC3/HC30/HC36), side mount cylinders (HC370), and splashwell mount cylinders (HC380). VERTICAL BLEEDER FITTING SET (HF1) Pair of 90-degree fi ttings with integrated vertical bleeders for use where clearances are tight. SeaStar Pivot Mount Parts The pivot front mount cylinder (P/N HC3) fi ts most single-engine applications without requiring additional connection hardware Nut 3/8" NF Nylock S.S Screw 3/8" x 1-1/" Hex Head S.S Washer 7/16 dia. S.S Nut 7/16 NF Nylock S.S. 007 Washer 1/ dia. S.S Nut 1/ NF Nylock (nickel plated brass) Spacer (Thick) Spacer (Thin) Support Rod Adjusting Nut & Screw Washer /8 dia. S.S Support Bracket 13 HC36 1 Pivot Cylinder Sub as sem bly w/ Fittings (previously listed as 88000) HF0 HF1 NOTE: THE HC30, HC3 AND HC36 CYLINDERS ARE DISCONTINUED. Service parts are still available. If replacing, use the pivot front mount cylinder (HC3) when splashwell width is greater than. For questions about these applications, please contact Telefl ex Canada Tech Service at exmarine.com. HC3 CYLINDER PARTS NOTE: Adapter kits are not required when using the HC3 cylinder for single engine applications. The diagram shown is typical, but some ap pli ca tions do not use some of the parts shown or require different ori en ta tion of items from what is depicted. Always consult current SeaStar documents for diagrams specifi c to your application. Pivot Mount Cylinder Dual & Triple Engine Tie Bars WITH NEW STYLE HO6001/600/6003 TIE BAR KITS: No adapters are required. Use the dual and triple engine application guides on Pages 6 and 7 to select the tie bar kit required. WITH OLDER SEASTAR TIE BAR KITS: When using the HC3 with a pre-1998 SeaStar tie bar kit, contact Telefl ex Canada Technical Service for assistance at or online at exmarine.com TYPICAL FRONT MOUNT TIE BAR KIT FOR HC3 TYPE FRONT MOUNT CYL IN DER HO6001/HO600/HO6003 HO0 TYPICAL OLD STYLE SEASTAR TIE BAR KIT (Older model tie bar-and-adapter kits for the HC30/HC3 cylinders include a HO009 out board tie bar and engine-specifi c adapter plate kit [tie bar-to-engine ex ten sion plate] with all necessary hardware to connect the tie bar to the cylinder and two () engines. Single engine adapter plate kits are also available.) For exact parts orientation, consult SeaStar Owners Manual for the diagram specifi c to your application. 13

7 Cylinders: Outboard Front Mount - OLD STYLE SeaStar steering parts HC3/HC30 OLD STYLE ( STAN DARD ) CYLINDER PARTS Cylinder Parts & Single Engine Connection Parts (for Old Style HC3 & HC30 cylinders) For exact parts ori en ta tion, consult SeaStar Owners Manual #1 for the diagram specific to your ap pli ca tion. NOTE: HC3 is similar to the older HC30 model except for integral bleeder fittings The standard front mount cylinder (P/N HC3) fi ts most single-engine applications without requiring additional connection hardware. Some engines require use of an adapter plate kit. Contact Telefl ex Canada Tech service for adapter plate information. 1* 7 1 Slide Plate * 77 Screw /16" x 3/" Hex Head 3* Nut 3/8" NF Nylock * Notched Washer * 777 Slide Washer 6* Slide Follower 7* Follower Bushing 8* Bottom Washer (3 Hole) 9* Countersunk Washer 10* Screw 3/8" x 1-/8" Flat Head 11 HC3 1 Cylinder Subassembly w/fittings Support Rod 13* 011 Washer /8" dia. 1* 789 Spacer Support Bracket (avail. as P/N 8099) 16* Adjusting Nut with Set Screw 17* 007 Washer 1/" dia. 18* 1916 Nut 1/" NF Nylock 19* Nut 7/16" dia. 0* 7316 Washer 7/16" dia. 1* 3 Bleed Screw with Seal * 0109 Washer /16" dia. * Items 1- (except items 11, 1 & 1) are available as Kit # 701 (Items 9 & 10 are not used on 198-date HP Force Engines.) 1

8 hydraulic steering service parts: outboard cylinders Dual Engine Tie Bar & Adapter Plate Kits (for Old Style HC3 & HC30 (cylinders) TYPICAL TIE BAR & ADAPTER FOR HC3/HC The tie bar-and-adapter kits listed include a HO009 out board tie bar and engine-specific adapter plate kit (tie bar-to-engine extension plate) with all necessary hardware to connect the tie bar to the HC30/HC3 old style cylinder and engines. Single-engine adapter plate kits are also available. -Engine Adapter Kits P/N HO0 -Engine adapter kits include the following items shown in the diagram above. (1-Engine kits have half the quantities listed below.) Clamp Plate (varies) or Bottom Washer (varies) Extension Plate (Tie Bar Adapter) Nut 1/ NC Nylock Tie Bar Only Kit HO009 Includes the following items shown in diagram above Nut 3/8 NF Nylock 1136 Washer 3/8 dia Screw 3/8 NF x 1-3/ Hex Head Stringer Tube Threaded Rod with Ball Joint Plastic Cap Nut 1/ NF Nylock Ball Joint Screw 3/8 x 1-/8 Flat Head HO0 TYPICAL OLD STYLE SEASTAR TIE BAR KIT, SHOWN AS SEM BLED WITH ADAPTER PLATES For exact parts orientation, consult SeaStar Owners Manual #1.1 for the diagram specific to your application. 1

9 Cylinders: Outboard Side Mount SeaStar steering parts HC370 SIDEMOUNT CYLINDER PARTS Cylinder Parts SIDE MOUNT CYLINDER SEAL KIT (HS13) Replacement front seal for kit for standard SeaStar side mount cylinders (HC370). Includes seals only. Also available: Rod End Gland with Swivel Nut and Seals: (P/N HS173), Cylinder Tube & Gland Assembly (P/N 7737), Cylinder Rod & Piston Assembly (P/N 77386). SIDE MOUNT CYLINDER ROD END GLAND KIT (HS173) Includes rod end gland, swivel nut and seals for HC370 cylinder. CYLINDER BLEEDER TEE FITTING SET (HF0) Pair of P/N 0960 bleeder tee fi ttings for older-style SeaStar front mount cylinders (HC3 & HC36), side mount cylinders (HC370), and splashwell mount cylinders (HC380). Replaces 81 elbow style fi ttings. For illustrations, see front mount cylinder part list. VERTICAL BLEEDER FITTING SET (HF1) Pair of 90 fi ttings with integrated vertical bleeders, for tight clearances. For illustrations, see front mount cylinder part list. Dual Engine Tie Bar Kits & Parts SIDE MOUNT CYLINDER TIE BAR KIT (HO009) Replacement parts for the HO009 tie bar kit are listed below Nut 3/8" NF Nylock 1136 Washer 3/8" dia Screw 3/8" NF x 1-3/" Hex Head Stringer Tube Threaded Rod with Ball Joint Plastic Cap Nut 1/" NF Nylock Ball Joint (USE ENGINE MANUFACTURER S LINK ARM.) Cylinder/Connection Parts SIDE MOUNT CYLINDER PARTS LIST (HC370) Side Mount Cyl. Tube & Gland Ass y Extension Rod Stainless Steel Pin - Stainless Steel HF0 1 Hose/Bleeder Tee Fitting Set () 90 Bleed Screw 6 89 Washer for Bleed Screw Cylinder Rod & Piston Assembly (USE ENGINE MANUFACTURER S LINK ARM.) HO009 SIDE MOUNT CYLINDER TIE BAR KIT (ALL ENGINES) ENGINE CENTER DISTANCE 3 (WITH STANDARD TIE BAR:) MINIMUM ENGINE CENTER DISTANCE: 6" (660mm) MAXIMUM ENGINE CENTER DISTANCE: 36" (91mm) 16

10 hydraulic steering service parts: outboard cylinders Cylinders: Outboard Splashwell Mount HC380 SPLASHWELL CYLINDER TYPICAL SINGLE ENGINE MOUNTING Cylinder Parts SPLASHWELL MOUNT CYLINDER SEAL KIT (HS1) Replacement front seal for kit for standard SeaStar splash well mount cylinders (HC380). Includes seals only. SIDE MOUNT CYLINDER ROD END GLAND (61) Includes rod end gland only for HC380 cylinder. CYLINDER BLEEDER TEE FITTING SET (HF0) Pair of P/N 0960 bleeder tee fi ttings for older-style SeaStar front mount cylinders (HC3 & HC36), side mount cylinders (HC370), and splashwell mount cylinders (HC380). Replaces 81 elbow style fi ttings. For illustrations, see front mount cylinder part list. VERTICAL BLEEDER FITTING SET (HF1) Pair of 90-degree fi ttings with integrated vertical bleeders for use where clearances are tight, such as some stern drive applications. For illustrations, see front mount cylinder part list. Dual Engine Cylinder Tie Bar Kit HO010 SPLASHWELL MOUNT CYLINDER TIE BAR KIT (ALL EN GINES) (WITH STANDARD TIE BAR:) MINIMUM ENGINE CENTER DISTANCE: 6" (660mm) MAXIMUM ENGINE CENTER DISTANCE: 36" (91mm) Outboard Catamaran/Pontoon HC33 CYLINDERS ARE BASED ON THE HC3 FRONT MOUNT CYLINDER DESIGN. FOR AVAILABLE PARTS, PLEASE SEE THE HC3 CYLINDER, ON PREVIOUS FOUR PAGES. FOR HC37 PARTS, PLEASE CONTACT TELEFLEX CANADA. 17

11 Cylinders: Stern Drive (I/O) SeaStar Internal Mount SeaStar steering parts THE HYNAUTIC K- EXTERNAL-MOUNT STERN DRIVE CYLINDER SEAL KIT IS LISTED WITH THE CYLINDER SEAL KITS IN THE CHART ON A PREVIOUS PAGE, FOR OTHER K- SERVICE PARTS, PLEASE CONTACT TELEFLEX CANADA: OR ON-LINE AT: exmarine.com HC31 PARTS LIST: 1 HP611 1 Trunnion Assembly Gland Ball 3 HF0 Bleeder Tee Fitting Barrel Gland End Piston/Shaft Rod End Ball Joint - N/A 1 Spanner Wrench - HS16 Seals Only Kit - HS16 Gland Ball & Gland End Kit HC36 PARTS LIST: Gland End Barrel Gland Trunnion Piston/Shaft 0987 Bleeder Tee Fitting Bushing Shim - N/A 1 Spanner Wrench - HS16 Seals Only Kit HC37* PARTS LIST: Gland End 0987 Bleeder Tee Fitting - HS1 Seals Only Kit HC38 PARTS LIST: Gland End 0987 Bleeder Tee Fitting Barrel Gland (Merc) Extension Tube Piston/Shaft Extension Rod - N/A 1 Spanner Wrench - HS1 Seals Only Kit HC31 1 HC36/HC37 HC NOTE: HC37 does not utilize items #6 & 7. SOME service parts are available for this cylinder. *HC37 can be replaced with HC330, but requires a tilt tube for installation HC39 PARTS LIST: Gland End 0987 Bleeder Tee Fitting Barrel Gland (Merc) 70 1 Tube Support Bushing Screw Piston Shaft Extension Rod - N/A 1 Spanner Wrench - HS1 Seals Only Kit P/N HC

12 hydraulic steering service parts: stern drive cylinders HC330 PARTS LIST: Gland End 0987 Bleeder Tee Fitting Barrel Gland (Merc) Piston/Shaft Extension Rod - N/A 1 Spanner Wrench - HS1 Seals Only Kit HC331 PARTS LIST: Nut 7/16 NF Washer 7/ Support Bracket Mounting Stud 66 1 Gland End 6 HF0 Bleeder Tee Fitting Barrel Gland End Piston/Shaft Nut 1/ NF Clevis Pin Cotter Pin Clevis Block Set Screw # Spacer (DPS & SX only) Support Rod - HS13 Seals Only Kit P/N HC P/N HC331 (con cealed) HC HC33 PARTS LIST: Bleed Tee Assembly 0631 Gland End Barrel Nut 1/ NF Nylok, Nickel-Plated Brass * /8 NF Nylok Thin SS * SHCS, 3/8 NF x 1-1/ SS ** (not shown) Loctite - HS1 Seals Only Kit * Item (1139) must be installed between Clevis Forks. P/N HC ** Apply. ml item 7 (3731) Loctite, to threaded portion of item 6 (01) before threading into item (1139). NOTE: When replacing any seals, make sure the cylinder shaft is clear of abrasions. An Oilite bushing should be ordered when replacing most glands. See SeaStar Manual # for details specifi c to your application. SeaStar, Capilano & Hynautic Cylinder Repair Parts SERVICE PARTS FOR CAPILANO MANUAL INBOARD AND POWER STEERING CYLINDERS: CONTACT TELEFLEX CANADA : OR ON-LINE AT: 19