PDB18 Series - 17 mm Rotary Potentiometer

Transcription

1 *RoHS COMPINT eatures Single and dual section control Metal shaft styles Carbon element Center and multiple detent options Wide range of resistance tapers Plain or knurled shaft options PDB18 Series - 17 mm Rotary Potentiometer Electrical Characteristics Taper... inear, audio Standard Resistance Range...1 K ohms to 1 M ohms Standard Resistance Tolerance...± % Residual Resistance... 1 % max. Environmental Characteristics Operating Temperature...- C to + C Power Rating inear watt Dual Section... watt udio watt Dual Section watt Maximum Operating Voltage inear... 0 V udio... 1 V Sliding Noise mv max. Mechanical Characteristics Mechanical ngle... 0 ±5 Rotational Torque... to 1 gf-cm Detent Torque... 1 to 0 g-cm Stop Strength...5 kg-cm min. Rotational ife...15,000 cycles Soldering Condition... 2 C max. within 3 seconds Hardware...One flat washer and mounting nut supplied per potentiometer with bushing Rating Power Ratio (%) Derating Curve mbient Temperature ( C) PDB181-K (.141) SHT SHOWN IN CCW POSITION KNUR.5 (.492) PDB (.141).047) 1 (.5) KNUR 1 (.531) 18.0 ± (.8 ±.019) 1 3 SCHEMTIC 2.0 (.393) SHT SHOWN IN CCW POSITION *RoHS Directive 02/95/EC Jan. 27, 03 including annex and RoHS Recast 11/65/EU June 8, 11.

2 dditional eatures inear, audio and reverse audio taper options RoHS compliant* pplications udio/tv sets Car radio mplifiers/mixers/drum machines/ synthesizers PCs/monitors ppliances PDB18 Series - 17 mm Rotary Potentiometer PDB181-B 9.0 (.354) 1 (.5) KNUR 23.0 ± (.5 ±.019) PDB181-E (.511) SHT SHOWN IN CCW POSITION KNUR PDB181-D 1 (.7) KNUR SHT SHOWN IN CCW POSITION.0 (.393) SHT SHOWN IN CCW POSITION Specifi cations are subject to change without notice.

3 1 (.3) ± +0/ (.519) (.7) 1 SHT SHOWN IN CCW POSITION KNUR (.7) (.138) ± 23.0 (.6) 9.0 (.354) (.138) SHT SHOWN IN CCW POSITION 3.8 (.149) 6 PCS. SHT SHOWN IN CCW POSITION KNUR.5 (.492) SCHEMTIC

4 PDB182-D Dual Gang Shaft Styles K Type 15 (.591) 18 (.9) ± ( ±.0) (.453) 14 (.551) 19 (.748) 1 (.531) 1 (.551) 8.0 (.314) KNUR (.453) 1 KNUR P Type KNUR +0/-0.1 SOT SHOWN IN CCW POSITION 9.7 (.381) Type 15 (.591) 35 (1.378) 6 PCS. 7 (.276) SHT SHOWN IN CCW POSITION SHT SHOWN IN CCW POSITION ± ( ±.0) +0/-0.1 Specifi cations are subject to change without notice.

5 X (%) X (%) Tapers 0 Series Tapers (): 6 (): 5 (): 4 (15): 3 (): 2 (05): 1 B Series Tapers (5B): B5 (4B): B4 (3B): B3 (2B): (2B): B2 (1B): B1 (B): B How To Order PDB K 4 K Model Number of Sections 1 = Single Section 2 = Dual Section Terminal Configuration (Pin ayout) (see individual drawings) K = PC Pins vertical/ (.5 mm) = PC Pins vertical/ (18.0 mm) B = PC Pins vertical (23.0 mm) E = Solder ugs Rear acing P = PC Pins Rear acing D = PC Pins ront acing Detent Option 2 = Center Detent 4 = No Detents 5 = Detent / 11 Position 6 = Detent / 21 Position 7 = Detent / 31 Position 8 = Detent / 41 Position Standard Shaft ength 15 = 15 mm 18 = 18 mm = mm = mm = mm Standard Resistance Table Resistance Resistance (Ohms) Code 1, , ,000 2,000 3,000 3,000 3, , , ,000, C Series Tapers Shaft Style = Metal latted Shaft K = Metal Knurled Type Shaft 18 Toothed Serration Type P = Metal Plain Shaft Resistance Code (See Table) Resistance Taper (See Taper Charts) Taper Series followed by Curve Number X (%) Other styles available. (C): C6 (C): C5 (C): C4 (15C): C3 (C): C (05C): C1 0 REV. 03/13