Tool Holder Catalog TRAUB TNX 65/42 VDI 30 HSK /Rö

Size: px
Start display at page:

Download "Tool Holder Catalog TRAUB TNX 65/42 VDI 30 HSK 40 142856-21.02.2014. 0214/Rö"

Transcription

1 Tool Holder Catalog TRAUB TNX 65/42 VDI 30 HSK /Rö

2 Disclaimer The illustrations in this documents may deviate from the delivered product. We reserve the right to make changes due to errors or based on technical advances. Abbreviations used in the catalog: EC = external cooling lubricant supply approx. = approximately D = diameter max = maximum min = minimum IC = internal cooling lubricant supply MT = Morse taper R = radius s = wrench size ST = steep taper SQ = square A Word on Copyright This document is proprietary and was originally written in German. Its reproduction and distribution in whole or in individual parts without permission of the copyright owner is prohibited and will be prosecuted under criminal or civil law. All rights reserved, including for translation. Copyright by INDEX-Werke GmbH & Co. KG Esslingen 2014 Copyright by TRAUB Drehmaschinen GmbH & Co. KG Reichenbach 2014

3 Table of Contents Table of Contents... 0 Technical Information TRAUB TNX 65/ Usage Information TRAUB TNX 65/ Tool holder fix,... 3 Tool holder fix, W-serration,... 4 Tool holder live,... 5 Tool holder live, W-serration,... 6 Tool holder to spring-loaded tap holder,... 7 Tool holder, Shank HSK Accessories TRAUB TNX 65/ Product notes For accessories for tool holders visit For more information, visit 3

4 For more information, visit 4

5 Table of Contents For more information, visit 0-1

6 For more information, visit 0-2

7 Technical Information TRAUB TNX 65/42 Catalog page Warranty 1-2 Information on wear parts Inspection of live tool holders and guide bushings Tool holders with cooling lubricant supply 1-3 lubricant filtering Cleaning live tool holders Speed ratio specifications on tool holders Direction of rotation specification 1-4 Tightening Torque 1-5 Replacement seals for tool shank Sealing air port Tool holders with fixation 1-6 High-pressure unit Load limits of live tools Live tool holders 1-7 Weight distribution on turret head 1-8 Collision Tool change on live tool holders For more information, visit A-1

8 Technical Information TRAUB TNX 65/42 Catalog page Information on how to use the chart 1-9 when using tool holders HSK Tool Dimensions 1-10 HSK Tool Dimensions 1-11 For more information, visit A-2

9 Usage Information TRAUB TNX 65/42 Catalog page Modular System of the TRAUB TNX 65/ Work Area of the TRAUB TNX 65/ Tool carrier 1 XYZ Tool carrier 2 XYZ Work Area of the TRAUB TNX 65/ Tool carrier 1 XYZ Tool carrier 2 XYZ Tool carrier 4 XYZ Work Area of the TRAUB TNX 65/ Tool carrier 1 XYZ Tool carrier 2 XYZ Tool carrier 3 XYZ Tool carrier 4 XYZ Work Area of the TRAUB TNX 65/ Tool carrier 2 XYZ Tool carrier 4 XYZ XYZB Swiveling Range TRAUB TNX 65/ Tool mounting VDI Performance Diagram Live tools, tool carriers 1-4 Speed range rpm For more information, visit B-1

10 Usage Information TRAUB TNX 65/42 Catalog page Performance Diagram 2-9 Live tools, milling unit Speed range rpm For more information, visit B-2

11 Tool holder fix Catalog page W Bar stop, live 3-2 Fixation none Mounting 92 (3.62) / / 31 (1.22) mm ('') W Bar stop, live 3-3 Fixation Mounting D58 / / 30 (1.18) mm ('') W Bar stop, live 3-4 Fixation Mounting D85 / / 30 (1.18) mm ('') W Compensation holder 3-5 Fixation TRAUB bar Mounting VDI 30 external and internal, p max 40 bar 90 mm (3.54 '') / / 2 (0.8) mm ('') W Compensation holder 3-6 Fixation TRAUB bar Mounting VDI 30 external and internal, p max 80 bar 90 mm (3.54 '') / / 100 (3.94) mm ('') W Drilling tool holder 3-7 Fixation TRAUB bar Mounting INDEX TRAUB CAPTO C3 internal, p max 80 bar 70 (2.76) / / 16 (0.63) mm ('') W Drilling tool holder 3-8 Fixation TRAUB bar Mounting INDEX TRAUB CAPTO C3 internal, p max 80 bar 62 (2.44) / / 16 (0.63) mm ('') For more information see C-1

12 Tool holder fix Catalog page W Drilling tool holder 3-9 Fixation TRAUB bar Mounting ER 25 external and internal, p max 80 bar 90 mm (3.54 '') / / 29 (1.14) mm ('') W Drilling tool holder 3-10 Fixation TRAUB bar Mounting ER 32 external and internal, p max 80 bar 90 mm (3.54 '') / / 50 (1.97) mm ('') W Drilling tool holder 3-11 Fixation TRAUB bar Mounting ER 40 external and internal, p max 80 bar 90 mm (3.54 '') / / 56 (2.2) mm ('') W Drilling tool holder 3-12 Fixation TRAUB bar Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 100 (3.94) / / mm ('') W Drilling tool holder 3-13 Fixation TRAUB bar Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 90 mm (3.54 '') / / 30 (1.18) mm ('') W Drilling tool holder 3-14 Fixation TRAUB bar Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 100 (3.94) / / 30 (1.18) mm ('') W Drilling tool holder 3-15 Fixation TRAUB bar Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 110 (4.33) / / 30 (1.18) mm ('') For more information see C-2

13 Tool holder fix Catalog page W Drilling tool holder, double 3-16 Fixation TRAUB bar Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 90 mm (3.54 '') / ±27 (±16) / 30 (1.18) mm ('') W Drilling tool holder 3-17 Fixation TRAUB bar Mounting DIN 1835 B/E D40 external and internal, p max 80 bar 90 mm (3.54 '') / / 30 (1.18) mm ('') W Drilling tool holder, shifted 3-18 Fixation TRAUB bar Mounting DIN 1835 B/E D40 external and internal, p max 80 bar 90 mm (3.54 '') / / mm ('') W Drilling tool holder 3-19 Fixation TRAUB bar Mounting INDEX TRAUB CAPTO C3 internal, p max 80 bar 75 (2.95) / / 6 (0.24) mm ('') W Drilling tool holder 3-20 Fixation TRAUB bar Mounting INDEX TRAUB CAPTO C4 internal, p max 80 bar 90 mm (3.54 '') / / 7 (0.28) mm ('') W Turning tool holder, Form C1/C Fixation none Mounting square 20x20 external, p max 40 bar 70 (2.76) / / 35 (1.38) mm ('') W Turning tool holder, Form C2/C Fixation none Mounting square 20x20 external, p max 40 bar 70 (2.76) / / 41 (1.61) mm ('') For more information see C-3

14 Tool holder fix Catalog page W Turning tool holder, double 3-23 Fixation TRAUB bar Mounting square 20x20 external, p max 80 bar 94.5 (3.72) / ±25 (±0.98) / 24 (0.94) mm ('') W Turning tool holder, double 3-24 Fixation TRAUB bar Mounting square 20x20 external, p max 80 bar 94.5 (3.72) / ±25 (±0.98) / 24 (0.94) mm ('') W Turning tool holder, Form C1/C Fixation none Mounting square 25x25 external, p max 40 bar 70 (2.76) / / 40 (1.57) mm ('') W Turning tool holder, Form C2/C Fixation none Mounting square 25x25 external, p max 40 bar 70 (2.76) / / 46 (1.81) mm ('') W Turning tool holder 3-27 Fixation none Mounting square 25x25 external, p max 20 bar 90 mm (3.54 '') / / 49 (1.93) mm ('') W Turning tool holder 3-28 Fixation none Mounting square 25x25 external, p max 20 bar 90 mm (3.54 '') / / 49 (1.93) mm ('') W Turning tool holder, double 3-29 Fixation none Mounting square 25x25 external, p max 20 bar 64 (2.52) / / 43 (1.69) mm ('') For more information see C-4

15 Tool holder fix Catalog page W Turning tool holder, Form B Fixation none Mounting square 20x20 external, p max 20 bar 77 (33) / / 35 (1.38) mm ('') W Turning tool holder, Form B Fixation none Mounting square 20x20 external, p max 20 bar 77 (33) / / 35 (1.38) mm ('') W Turning tool holder, Form B Fixation none Mounting square 20x20 external, p max 20 bar 60 (2.36) / / 35 (1.38) mm ('') W Turning tool holder, Form B Fixation none Mounting square 20x20 external, p max 20 bar 60 (2.36) / / 35 (1.38) mm ('') W Turning tool holder 3-34 Fixation TRAUB bar Mounting square 25x25 external, p max 80 bar 60 (2.36) / / 35 (1.38) mm ('') W Turning tool holder 3-35 Fixation TRAUB bar Mounting square 25x25 external, p max 80 bar 60 (2.36) / / 35 (1.38) mm ('') W Basic holder 3-36 Fixation TRAUB bar Mounting Fette T18 external, p max 40 bar 66 (2.6) / / 29 (1.14) mm ('') For more information see C-5

16 Tool holder fix Catalog page W Basic holder, vertically adjustable 3-37 Fixation TRAUB bar Mounting external, p max 80 bar 65 (2.56) / / 3 (0.12) mm ('') W Grooving tool holding block, vertically adjustable 3-38 Fixation Mounting Trapezoid 32x4 external, p max 20 bar 45 (1.77) / / 32 (1.26) mm ('') W Grooving tool holding block, vertically adjustable 3-39 Fixation Mounting Trapezoid 32x5 external, p max 20 bar 45 (1.77) / / 32 (1.26) mm ('') W Grooving tool holding block, vertically adjustable 3-40 Fixation Mounting Trapezoid 32x5 external, p max 20 bar 45 (1.77) / / 32 (1.26) mm ('') W Grooving tool holding block, vertically adjustable 3-41 Fixation Mounting Trapezoid 32x5 external, p max 20 bar 45 (1.77) / / 32 (1.26) mm ('') W Basic holder, adjustable 3-42 Fixation TRAUB bar Mounting external, p max 80 bar 38 (1.5) / / 32 (1.26) mm ('') W Grooving tool holding block 3-43 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 88 (3.46) / / 20 (0.79) mm ('') For more information see C-6

17 Tool holder fix Catalog page W Grooving tool holding block 3-44 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 88 (3.46) / / 20 (0.79) mm ('') W Grooving tool holding block 3-45 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 88 (3.46) / / 7 (0.28) mm ('') W Grooving tool holding block 3-46 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 88 (3.46) / / 7 (0.28) mm ('') W Grooving tool holding block 3-47 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 108 (4.25) / / 7 (0.28) mm ('') W Grooving tool holding block 3-48 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 87.5 (3.44) / / 15 (0.59) mm ('') W Center holder, live 3-49 Fixation none Mounting D15.4/Cone 1: (2.74) / / mm ('') W Center holder, elastic, live 3-50 Fixation none Mounting D15.4/Cone 1: (2.7) / / mm ('') For more information see C-7

18 Tool holder fix Catalog page W Scroll holder 3-51 Fixation none Mounting internal, p max 20 bar 60 (2.36) / / 42.5 (1.67) mm ('') W Scroll holder 3-52 Fixation none Mounting internal, p max 40 bar 68 (2.68) / / 70 (2.76) mm ('') W Steady rest, D 8-65 mm ( '') 3-53 Fixation TRAUB bar Mounting external, p max 20 bar (4.95) / / 15 (0.59) mm ('') W Closing tool holder 3-54 Fixation TRAUB bar Mounting DIN 1835 B/E D1'' internal, p max 20 bar 85 (3.35) / / 35 (1.38) mm ('') W Gripper 3-55 Fixation TRAUB bar Mounting (5.19) / / mm ('') W Calibrating tool 3-56 Fixation Mounting 200 (7.87) / / mm ('') W Coolant nozzle 3-57 Fixation none Mounting external, p max 20 bar 30 (1.18) / / mm ('') For more information see C-8

19 Tool holder fix Catalog page W Coolant nozzle 3-58 Fixation Mounting external, p max 80 bar 25 (0.98) / / mm ('') W Blanking plug 3-59 Fixation Mounting 15 (0.59) / / mm ('') For more information see C-9

20 Tool holder fix, W-serration Catalog page W Compensation holder 4-2 Fixation W serration Mounting VDI 30 external and internal, p max 40 bar 90 mm (3.54 '') / / 2 (0.8) mm ('') W Drilling tool holder 4-3 Fixation W serration Mounting INDEX TRAUB CAPTO C3 internal, p max 80 bar 62 (2.44) / / 16 (0.63) mm ('') W Drilling tool holder 4-4 Fixation W serration Mounting ER 25 external and internal, p max 80 bar 90 mm (3.54 '') / / 29 (1.14) mm ('') W Drilling tool holder 4-5 Fixation W serration Mounting ER 32 external and internal, p max 80 bar 90 mm (3.54 '') / / 50 (1.97) mm ('') W Drilling tool holder 4-6 Fixation W serration Mounting ER 40 external and internal, p max 80 bar 90 mm (3.54 '') / / 56 (2.2) mm ('') W Drilling tool holder 4-7 Fixation W serration Mounting DIN 1835 B/E D32 external and internal, p max 40 bar 100 (3.94) / / 9 (0.35) mm ('') W Drilling tool holder 4-8 Fixation W serration Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 100 (3.94) / / mm ('') For more information see D-1

21 Tool holder fix, W-serration Catalog page W Drilling tool holder 4-9 Fixation W serration Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 90 mm (3.54 '') / / 30 (1.18) mm ('') W Drilling tool holder 4-10 Fixation W serration Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 100 (3.94) / / 30 (1.18) mm ('') W Drilling tool holder 4-11 Fixation W serration Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 110 (4.33) / / 30 (1.18) mm ('') W Drilling tool holder, double 4-12 Fixation W serration Mounting DIN 1835 B/E D32 external and internal, p max 80 bar 90 mm (3.54 '') / ±27 (±16) / 30 (1.18) mm ('') W Drilling tool holder 4-13 Fixation W serration Mounting DIN 1835 B/E D40 external and internal, p max 80 bar 90 mm (3.54 '') / / 30 (1.18) mm ('') W Drilling tool holder 4-14 Fixation W serration Mounting INDEX TRAUB CAPTO C3 internal, p max 80 bar 75 (2.95) / / 6 (0.24) mm ('') W Drilling tool holder 4-15 Fixation W serration Mounting INDEX TRAUB CAPTO C4 internal, p max 80 bar 90 mm (3.54 '') / / 7 (0.28) mm ('') For more information see D-2

22 Tool holder fix, W-serration Catalog page W Turning tool holder, Form C1/C Fixation W serration Mounting square 25x25 external, p max 40 bar 60.6 (2.39) / / 35 (1.38) mm ('') W Turning tool holder, Form C2/C Fixation W serration Mounting square 25x25 external, p max 40 bar 60.6 (2.39) / / 56 (2.2) mm ('') W Turning tool holder, double 4-18 Fixation W serration Mounting square 25x25 external, p max 20 bar 62 (2.44) / / 43 (1.69) mm ('') W Turning tool holder 4-19 Fixation W serration Mounting square 25x25 external, p max 40 bar 86 (3.39) / / 35 (1.38) mm ('') W Basic holder, vertically adjustable 4-20 Fixation W serration Mounting external, p max 80 bar 65 (2.56) / / 3 (0.12) mm ('') W Grooving tool holding block, vertically adjustable 4-21 Fixation Mounting square 16x16 40 (1.57) / / 40 (1.57) mm ('') W Grooving tool holding block, vertically adjustable 4-22 Fixation Mounting square 16x16 20 (0.79) / / 17 (0.67) mm ('') For more information see D-3

23 Tool holder fix, W-serration Catalog page W Grooving tool holding block, vertically adjustable 4-23 Fixation Mounting Trapezoid 26x (1.87) / / 32 (1.26) mm ('') W Grooving tool holding block, vertically adjustable 4-24 Fixation Mounting Trapezoid 26x (1.87) / / 32 (1.26) mm ('') W Grooving tool holding block, vertically adjustable 4-25 Fixation Mounting Trapezoid 26x (1.87) / / 28.5 (1.12) mm ('') W Grooving tool holding block, vertically adjustable 4-26 Fixation Mounting Trapezoid 26x (1.87) / / 28.5 (1.12) mm ('') W Grooving tool holding block, vertically adjustable 4-27 Fixation Mounting Trapezoid 26x5 20 (0.79) / / 32 (1.26) mm ('') W Basic holder, adjustable 4-28 Fixation W serration Mounting external, p max 20 bar 38 (1.5) / / 32 (1.26) mm ('') W Grooving tool holding block 4-29 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 87.5 (3.44) / / 15 (0.59) mm ('') For more information see D-4

24 Tool holder fix, W-serration Catalog page W Grooving tool holding block 4-30 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 88 (3.46) / / 7 (0.28) mm ('') W Grooving tool holding block 4-31 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 88 (3.46) / / 20 (0.79) mm ('') W Grooving tool holding block 4-32 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 88 (3.46) / / 20 (0.79) mm ('') W Grooving tool holding block 4-33 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 88 (3.46) / / 7 (0.28) mm ('') W Grooving tool holding block 4-34 Fixation Mounting Trapezoid 32x8 external, p max 80 bar 108 (4.25) / / 7 (0.28) mm ('') W Center holder, vertically adjustable, not spring-loaded 4-35 Fixation W serration Mounting D15.4/Cone 1:7.5 external, p max 20 bar 90 mm (3.54 '') / ±0.5 (±02) / 56.5 (2.22) mm ('') W Center holder, vertically adjustable, spring-loaded 4-36 Fixation W serration Mounting D15.4/Cone 1:7.5 external, p max 20 bar 90 mm (3.54 '') / ±0.5 (±02) / 56.5 (2.22) mm ('') For more information see D-5

25 Tool holder live Catalog page W Drilling unit 5-2 Fixation TRAUB bar Mounting ER 11 external, p max 20 bar Speed ratio 1:3 (0.333) 80 (3.15) / / 15 (0.59) mm ('') W Drilling unit 5-3 Fixation TRAUB bar Mounting ER 16 external, p max 20 bar Speed ratio 1:2 (0.5) 70 (2.76) / / 30 (1.18) mm ('') W Drilling unit, double 5-4 Fixation TRAUB bar Mounting ER 16 external, p max 20 bar Speed ratio 1:2 (0.5) 96 (3.78) / ±25 (±0.98) / 17 (0.67) mm ('') W Drilling unit 5-5 Fixation TRAUB bar Mounting ER 20 external, p max 80 bar Speed ratio 1:3 (0.333) 90 mm (3.54 '') / / 35 (1.38) mm ('') W Drilling unit 5-6 Fixation TRAUB bar Mounting ER 20 external and internal, p max 80 bar Speed ratio 1:3 (0.333) 90 mm (3.54 '') / / 35 (1.38) mm ('') W Drilling unit 5-7 Fixation TRAUB bar Mounting ER 20 external and internal, p max 80 bar Speed ratio 1:2 (0.5) 90 mm (3.54 '') / / 35 (1.38) mm ('') W Drilling unit 5-8 Fixation none Mounting ER 25 internal, p max 80 bar Speed ratio 1:1 (1) 85 (3.35) / / mm ('') For more information see E-1

26 Tool holder live Catalog page W Drilling unit 5-9 Fixation none Mounting ER 25 external, p max 80 bar Speed ratio 1:1 (1) 67 (2.64) / / mm ('') W Drilling unit 5-10 Fixation TRAUB bar Mounting ER 25 external and internal, p max 80 bar Speed ratio 1.02:1 (1.02) 87 (3.43) / / 60 (2.36) mm ('') W Drilling unit 5-11 Fixation none Mounting DIN 1835 B/E D20 internal, p max 80 bar Speed ratio 1:1 (1) 89 (3.5) / / mm ('') W Drilling unit, adjustable 5-12 Fixation none Mounting D16 external, p max 40 bar Speed ratio 1:1 (1) 85 (3.35) / / mm ('') W Drilling unit 5-13 Fixation TRAUB bar Mounting WFB external, p max 80 bar Speed ratio 1:3 (0.333) 93.5 (3.68) / / 35 (1.38) mm ('') W Drilling unit 5-14 Fixation none Mounting WFB external, p max 80 bar Speed ratio 1:1 (1) 72 (2.83) / / mm ('') W Drilling unit 5-15 Fixation TRAUB bar Mounting WFB external, p max 40 bar Speed ratio 1:1 (1) 82 (3.23) / / mm ('') For more information see E-2

27 Tool holder live Catalog page W Fixation none Mounting ER 25 external, p max 80 bar Speed ratio 1:1 (1) 81 (3.19) / / mm ('') W Fixation TRAUB bar Mounting ER 25 external, p max 80 bar Speed ratio 1:1 (1) 94 (3.7) / / 31 (1.22) mm ('') W Fixation TRAUB bar Mounting ER 25 external, p max 80 bar Speed ratio 2:1 (2) 94 (3.7) / / 31 (1.22) mm ('') W Fixation none Mounting DIN 1835 B/E D16 external, p max 80 bar Speed ratio 1:1 (1) 86.5 (3.41) / / mm ('') W Fixation TRAUB bar Mounting DIN 1835 B/E D16 external, p max 40 bar Speed ratio 1:1 (1) 83 (3.27) / / 0 mm ('') W Fixation none Mounting DIN 1835 B/E D20 external, p max 80 bar Speed ratio 1:1 (1) 78 (37) / / mm ('') W Fixation none Mounting DIN 1835 B/E D20 external, p max 80 bar Speed ratio 1:1 (1) 86.5 (3.41) / / mm ('') For more information see E-3

28 Tool holder live Catalog page W Fixation TRAUB bar Mounting DIN 1835 B/E D20 external, p max 80 bar Speed ratio 2:1 (2) 97 (3.82) / / 31 (1.22) mm ('') W Fixation TRAUB bar Mounting DIN 1835 B/E D20 external, p max 40 bar Speed ratio 4:1 (4) 104 (49) / / mm ('') W Fixation none Mounting WFB external, p max 80 bar Speed ratio 1:1 (1) 86.5 (3.41) / / mm ('') W Fixation TRAUB bar Mounting Milling tool mounting D22 external, p max 40 bar Speed ratio 4:1 (4) 94 (3.7) / / mm ('') W Fixation TRAUB bar Mounting Milling tool mounting D27 external, p max 40 bar Speed ratio 4:1 (4) 94 (3.7) / / mm ('') W Fixation none Mounting INDEX TRAUB CAPTO C3 external, p max 80 bar Speed ratio 1:1 (1) 76 (2.99) / / 0 mm ('') W Fixation none Mounting external, p max 80 bar Speed ratio 1:1 (1) 76.5 (31) / / mm ('') For more information see E-4

29 Tool holder live Catalog page W Fixation TRAUB bar Mounting external, p max 20 bar Speed ratio 1:1 (1) 70.5 (2.78) / / mm ('') W Fixation TRAUB bar Mounting DIN 138 D22 external, p max 80 bar Speed ratio 2.04:1 (2.042) 97 (3.82) / / 65 (2.56) mm ('') W Tapping unit, extendable 5-32 Fixation none Mounting ER 25 external, p max 40 bar Speed ratio 1:1 (1) 84 (3.31) / / mm ('') W Circular saw unit 5-33 Fixation TRAUB bar Mounting Milling tool mounting D16 external, p max 80 bar Speed ratio 3.12:1 (3.125) 90 mm (3.54 '') / / mm ('') W Drilling unit 5-34 Fixation TRAUB bar Mounting ER 20 external, internal optional, p max 80 bar Speed ratio 1:3 (0.333) 90 mm (3.54 '') / / 96 (3.78) mm ('') W Drilling unit 5-35 Fixation TRAUB bar Mounting ER 20 external, internal optional, p max 80 bar Speed ratio 1:2 (0.5) 90 mm (3.54 '') / / 96 (3.78) mm ('') W Drilling unit, double 5-36 Fixation TRAUB bar Mounting ER 25 external, p max 20 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / mm ('') For more information see E-5

30 Tool holder live Catalog page W Drilling unit 5-37 Fixation TRAUB bar Mounting DIN 1835 B/E D16 internal, p max 80 bar Speed ratio 1:2 (0.5) 90 mm (3.54 '') / / mm ('') W Drilling unit 5-38 Fixation TRAUB bar Mounting DIN 1835 B/E D16 external, internal optional, p max 80 bar Speed ratio 1:2 (0.5) 90 mm (3.54 '') / / 100 (3.94) mm ('') W Drilling unit 5-39 Fixation TRAUB bar Mounting WFB external, internal optional, p max 80 bar Speed ratio 1:3 (0.333) 90 mm (3.54 '') / / 98 (3.86) mm ('') W Drilling unit 5-40 Fixation TRAUB bar Mounting WFB external, internal optional, p max 80 bar Speed ratio 1:2 (0.5) 90 mm (3.54 '') / / 98 (3.86) mm ('') W Fixation TRAUB bar Mounting ER 25 external, internal optional, p max 20 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 75 (2.95) mm ('') W Fixation TRAUB bar Mounting ER 25 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 84 (3.31) mm ('') W Fixation TRAUB bar Mounting ER 25 external, internal optional, p max 20 bar Speed ratio 2:1 (2) 90 mm (3.54 '') / / 75 (2.95) mm ('') For more information see E-6

31 Tool holder live Catalog page W Fixation TRAUB bar Mounting DIN 1835 B/E D16 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 93 (3.66) mm ('') W Fixation TRAUB bar Mounting DIN 1835 B/E D20 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 93 (3.66) mm ('') W Fixation TRAUB bar Mounting DIN 1835 B/E D20 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 93 (3.66) mm ('') W Fixation TRAUB bar Mounting DIN 1835 B/E D20 external, internal optional, p max 80 bar Speed ratio 2:1 (2) 90 mm (3.54 '') / / 93 (3.66) mm ('') W , double 5-48 Fixation TRAUB bar Mounting WFB external and internal, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / 2x32 (2x1.26) / 63 (2.48) mm ('') W Fixation TRAUB bar Mounting WFB external and internal, p max 20 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 85.5 (3.37) mm ('') W Fixation TRAUB bar Mounting WFB external and internal, p max 80 bar Speed ratio 1:1 (1) 120 (4.72) / / 85.5 (3.37) mm ('') For more information see E-7

32 Tool holder live Catalog page W Fixation TRAUB bar Mounting WFB external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 92 (3.62) mm ('') W Fixation TRAUB bar Mounting WFB external, internal optional, p max 80 bar Speed ratio 2:1 (2) 90 mm (3.54 '') / / 92 (3.62) mm ('') W Fixation TRAUB bar Mounting Milling tool mounting D22 external, p max 20 bar Speed ratio 2.36:1 (2.36) 80 (3.15) / / 47 (1.85) mm ('') W Fixation TRAUB bar Mounting INDEX TRAUB CAPTO C3 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 53.5 (2.11) mm ('') W Fixation TRAUB bar Mounting external, p max 20 bar Speed ratio 2:1 (2) 70 (2.76) / / 67.5 (2.66) mm ('') W High-frequency spindle unit 5-56 Fixation TRAUB bar Mounting ER 11 external, p max 5 bar Speed ratio 1:3.85 (0.26) (44) / / 85.5 (3.37) mm ('') W Broaching/ Slotting unit 5-57 Fixation TRAUB bar Mounting D20 external, p max 20 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 88 (3.46) mm ('') For more information see E-8

33 Tool holder live Catalog page W Polygon turning unit 5-58 Fixation TRAUB bar Mounting Milling tool mounting D27 external, p max 20 bar Speed ratio 1:1 (1) 65 (2.56) / / 69 (2.72) mm ('') W Drilling unit, angle-adjustable 5-59 Fixation TRAUB bar Mounting ER 16 external, p max 40 bar Speed ratio 1:1 (1) 65 (2.56) / / mm ('') W Gear cutting unit, angle-adjustable, ± Fixation TRAUB bar Mounting D16 external, p max 20 bar Speed ratio 2:1 (2) 96.2 (3.79) / / mm ('') W Milling cutter holding block 5-61 Fixation Mounting Milling tool mounting D13 / / mm ('') W Milling cutter holding block 5-62 Fixation Mounting Milling tool mounting D16 / / mm ('') W Milling cutter holding block 5-63 Fixation Mounting Milling tool mounting D22 / / mm ('') W Milling cutter holding block 5-64 Fixation Mounting Milling tool mounting D27 / / mm ('') For more information see E-9

34 Tool holder live Catalog page W Milling cutter holding block 5-65 Fixation Mounting Milling tool mounting D32 / / mm ('') For more information see E-10

35 Tool holder live, W-serration Catalog page W Drilling unit 6-2 Fixation W serration Mounting ER 11 external, p max 40 bar Speed ratio 1:3 (0.333) 75 (2.95) / / 15 (0.59) mm ('') W Drilling unit, double 6-3 Fixation W serration Mounting ER 16 external, p max 40 bar Speed ratio 1:2 (0.5) 78 (37) / ±25 (±0.98) / 30 (1.18) mm ('') W Drilling unit 6-4 Fixation W serration Mounting ER 20 external, p max 80 bar Speed ratio 1:3 (0.333) 86.9 (3.42) / / 35 (1.38) mm ('') W Drilling unit 6-5 Fixation W serration Mounting ER 20 external and internal, p max 80 bar Speed ratio 1:3 (0.333) 86.9 (3.42) / / 35 (1.38) mm ('') W Drilling unit 6-6 Fixation W serration Mounting ER 20 external, p max 80 bar Speed ratio 1:2 (0.5) 86.9 (3.42) / / 35 (1.38) mm ('') W Drilling unit 6-7 Fixation W serration Mounting ER 20 external and internal, p max 80 bar Speed ratio 1:2 (0.5) 86.9 (3.42) / / 35 (1.38) mm ('') W Drilling unit 6-8 Fixation W serration Mounting WFB external, p max 80 bar Speed ratio 1:3 (0.333) 90.4 (3.56) / / 35 (1.38) mm ('') For more information see F-1

36 Tool holder live, W-serration Catalog page W Fixation W serration Mounting DIN 1835 B/E D20 external, p max 80 bar Speed ratio 1:1 (1) 93.9 (3.7) / / 31 (1.22) mm ('') W Fixation W serration Mounting DIN 1835 B/E D20 external, p max 80 bar Speed ratio 2:1 (2) 93.9 (3.7) / / 31 (1.22) mm ('') W Fixation W serration Mounting INDEX TRAUB CAPTO C3 external, p max 80 bar Speed ratio 1:1 (1) 76 (2.99) / / 0 mm ('') W Drilling unit 6-12 Fixation W serration Mounting ER 20 PRECI-FLEX external, p max 40 bar Speed ratio 1:2 (0.5) 90 mm (3.54 '') / / 91 mm (3.58 '') mm ('') W Fixation W serration Mounting ER 25 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 84 (3.31) mm ('') W Fixation W serration Mounting ER 25 external, internal optional, p max 80 bar Speed ratio 2:1 (2) 90 mm (3.54 '') / / 84 (3.31) mm ('') W Fixation W serration Mounting ER 25 PRECI-FLEX external, internal optional, p max 80 bar Speed ratio 2:1 (2) 90 mm (3.54 '') / / 89 (3.5) mm ('') For more information see F-2

37 Tool holder live, W-serration Catalog page W Fixation W serration Mounting DIN 1835 B/E D16 external and internal, p max 80 bar Speed ratio 1:1.7 (0.588) 90 mm (3.54 '') / / 97 (3.82) mm ('') W Fixation W serration Mounting DIN 1835 B/E D16 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 93 (3.66) mm ('') W Fixation W serration Mounting DIN 1835 B/E D20 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 93 (3.66) mm ('') W Fixation W serration Mounting DIN 1835 B/E D20 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 93 (3.66) mm ('') W Fixation W serration Mounting DIN 1835 B/E D20 external, internal optional, p max 80 bar Speed ratio 2:1 (2) 90 mm (3.54 '') / / 93 (3.66) mm ('') W Fixation W serration Mounting WFB external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 92 (3.62) mm ('') W Fixation W serration Mounting WFB external, internal optional, p max 80 bar Speed ratio 2:1 (2) 90 mm (3.54 '') / / 92 (3.62) mm ('') For more information see F-3

38 Tool holder live, W-serration Catalog page W Fixation W serration Mounting Milling tool mounting D22 external, p max 80 bar Speed ratio 2.36:1 (2.36) 80 (3.15) / / 40 (1.57) mm ('') W Fixation W serration Mounting INDEX TRAUB CAPTO C3 external, internal optional, p max 80 bar Speed ratio 1:1 (1) 90 mm (3.54 '') / / 53.5 (2.11) mm ('') W Fixation W serration Mounting external, p max 40 bar Speed ratio 2:1 (2) 75 (2.95) / / 67.5 (2.66) mm ('') W Drilling unit, angle-adjustable 6-26 Fixation W serration Mounting ER 16 external, p max 40 bar Speed ratio 1:1 (1) 65 (2.56) / / mm ('') W Milling cutter holding block 6-27 Fixation Mounting Milling tool mounting D13 / / mm ('') W Milling cutter holding block 6-28 Fixation Mounting Milling tool mounting D16 / / mm ('') W Milling cutter holding block 6-29 Fixation Mounting Milling tool mounting D22 / / mm ('') For more information see F-4

39 Tool holder live, W-serration Catalog page W Milling cutter holding block 6-30 Fixation Mounting Milling tool mounting D27 / / mm ('') W Milling cutter holding block 6-31 Fixation Mounting Milling tool mounting D32 / / mm ('') For more information see F-5

40 Tool holder to spring-loaded tap holder Catalog page W Bar stop, adjustable, live 7-2 Fixation none Mounting ( ) / / mm ('') W Bar stop, adjustable, live 7-3 Fixation none Mounting ( ) / / mm ('') W Compensation bushing 7-4 Fixation none Mounting D3/4'' 6 (0.24) / / mm ('') W Compensation bushing 7-5 Fixation none Mounting D1'' 6 (0.24) / / mm ('') W Compensation holder 7-6 Fixation none Mounting D1'' internal, p max 20 bar 60 (2.36) / / mm ('') W Drilling tool holder, Form E4 7-7 Fixation none Mounting ER 25 internal, p max 80 bar 68 (2.68) / / mm ('') W Drilling tool holder, Form E4 7-8 Fixation none Mounting ER 32 internal, p max 20 bar 76 (2.99) / / mm ('') For more information see G-1

41 Tool holder to spring-loaded tap holder Catalog page W Drilling tool holder, Form E4 7-9 Fixation none Mounting ER 40 internal, p max 80 bar 80 (3.15) / / mm ('') W Drilling tool holder, Form E Fixation none Mounting DIN 1835 E D20 internal, p max 80 bar 67 (2.64) / / mm ('') W Drilling tool holder, Form E Fixation none Mounting DIN 1835 E D25 internal, p max 80 bar 71 (2.8) / / mm ('') W Drilling tool holder, Form E Fixation none Mounting D8 external and internal, p max 20 bar 60 (2.36) / / mm ('') W Drilling tool holder, Form E Fixation none Mounting D10 external and internal, p max 20 bar 60 (2.36) / / mm ('') W Drilling tool holder, Form E Fixation none Mounting D12 external and internal, p max 20 bar 60 (2.36) / / mm ('') W Drilling tool holder, Specially for the marking tool WriteStar 7-15 Fixation none Mounting D12 68 (2.68) / / mm ('') For more information see G-2

42 Tool holder to spring-loaded tap holder Catalog page W Drilling tool holder, Form E Fixation none Mounting D16 external and internal, p max 20 bar 60 (2.36) / / mm ('') W Drilling tool holder, Form E Fixation none Mounting D20 external and internal, p max 20 bar 60 (2.36) / / mm ('') W Drilling tool holder, Form E Fixation none Mounting D25 external and internal, p max 20 bar 60 (2.36) / / mm ('') W Drilling tool holder 7-19 Fixation none Mounting D25 external and internal, p max 40 bar 45 (1.77) / / mm ('') W Drilling tool holder, Form E Fixation none Mounting D32 external, p max 20 bar 70 (2.76) / / mm ('') W Drilling tool holder 7-21 Fixation none Mounting D32 internal, p max 80 bar 73 (2.87) / / mm ('') W Drilling tool holder 7-22 Fixation none Mounting MK1 external, p max 20 bar 30 (1.18) / / mm ('') For more information see G-3

43 Tool holder to spring-loaded tap holder Catalog page W Drilling tool holder 7-23 Fixation none Mounting MK2 external, p max 20 bar 27 (16) / / mm ('') W Drilling tool holder 7-24 Fixation none Mounting MK3 external, p max 20 bar 45 (1.77) / / mm ('') W Basic holder, vertically adjustable 7-25 Fixation none Mounting external, p max 20 bar 14 (0.55) / / mm ('') W Drill holding block 7-26 Fixation Mounting ER 25, p max 40 bar 30 (1.18) / / mm ('') W Drill holding block 7-27 Fixation Mounting D32, p max 40 bar 57 (2.24) / / mm ('') W Center holder, live 7-28 Fixation none Mounting D15.4/Cone 1: (2.74) / / mm ('') W Center holder, elastic, live 7-29 Fixation none Mounting D15.4/Cone 1: (2.7) / / mm ('') For more information see G-4

44 Tool holder to spring-loaded tap holder Catalog page W Tapping tool holder, extendable 7-30 Fixation none Mounting D25 external, p max 20 bar 73 (2.87) / / mm ('') W Reaming tool holder, adjustable 7-31 Fixation none Mounting ER 25 external, p max 20 bar 73.5 (2.89) / / mm ('') W Reaming tool holder, adjustable 7-32 Fixation none Mounting D18 external, p max 20 bar 59 (2.32) / / mm ('') W Reaming tool holder, self-centering 7-33 Fixation none Mounting D20 internal, p max 40 bar 93 (3.66) / / mm ('') W Broaching/ Slotting tool holder, rotating, live 7-34 Fixation none Mounting D12 external, p max 20 bar 60 (2.36) / / mm ('') For more information see G-5

45 Tool holder Shank HSK 40 Catalog page W Drilling tool holder 8-2 Form A Mounting ER 16 internal, p max 80 bar X / Z 50 (1.97) / mm ('') W Drilling tool holder 8-3 Form A Mounting ER 16 internal, p max 80 bar X / Z 80 (3.15) / mm ('') W Drilling tool holder 8-4 Form A Mounting ER 20 internal, p max 80 bar X / Z 55 (2.17) / mm ('') W Drilling tool holder 8-5 Form A Mounting ER 25 internal, p max 80 bar X / Z 60 (2.36) / mm ('') W Drilling tool holder 8-6 Form A Mounting ER 25 internal, p max 80 bar X / Z 80 (3.15) / mm ('') W Drilling tool holder 8-7 Form A Mounting ER 32 internal, p max 80 bar X / Z 63 (2.48) / mm ('') W Drilling tool holder 8-8 Form A Mounting DIN 1835 B/E D5 internal, p max 80 bar X / Z 45.5 (1.79) / mm ('') For more information see H-1

46 Tool holder Shank HSK 40 Catalog page W Drilling tool holder 8-9 Form A Mounting DIN 1835 B/E D5 internal, p max 80 bar X / Z 60 (2.36) / mm ('') W Drilling tool holder 8-10 Form A Mounting DIN 1835 B/E D6 internal, p max 80 bar X / Z 45.5 (1.79) / mm ('') W Drilling tool holder 8-11 Form A Mounting DIN 1835 B/E D8 internal, p max 80 bar X / Z 45.5 (1.79) / mm ('') W Drilling tool holder 8-12 Form A Mounting DIN 1835 B/E D10 internal, p max 80 bar X / Z 45.5 (1.79) / mm ('') W Drilling tool holder 8-13 Form A Mounting DIN 1835 B/E D12 internal, p max 80 bar X / Z 45.5 (1.79) / mm ('') W Drilling tool holder 8-14 Form A Mounting DIN 1835 B/E D14 internal, p max 80 bar X / Z 45.5 (1.79) / mm ('') W Drilling tool holder 8-15 Form A Mounting DIN 1835 B/E D16 internal, p max 50 bar X / Z 55.5 (2.19) / mm ('') For more information see H-2

47 Tool holder Shank HSK 40 Catalog page W Drilling tool holder 8-16 Form A Mounting DIN 1835 B/E D20 internal, p max 80 bar X / Z 55.5 (2.19) / mm ('') W Drilling tool holder 8-17 Form A Mounting DIN 1835 B/E D25 internal, p max 50 bar X / Z 65.5 (2.58) / mm ('') W Drilling tool holder 8-18 Form A Mounting D6 internal, p max 80 bar X / Z 60 (2.36) / mm ('') W Drilling tool holder 8-19 Form A Mounting D8 internal, p max 80 bar X / Z 60 (2.36) / mm ('') W Drilling tool holder 8-20 Form A Mounting D10 internal, p max 80 bar X / Z 60 (2.36) / mm ('') W Drilling tool holder 8-21 Form A Mounting D12 internal, p max 80 bar X / Z 70 (2.76) / mm ('') W Drilling tool holder 8-22 Form A Mounting D14 internal, p max 80 bar X / Z 75 (2.95) / mm ('') For more information see H-3

48 Tool holder Shank HSK 40 Catalog page W Drilling tool holder 8-23 Form A Mounting D16 internal, p max 80 bar X / Z 75 (2.95) / mm ('') W Drilling tool holder, with shrink-fit mounting 8-24 Form A Mounting Shrink-fit mounting D6 internal, p max 80 bar X / Z 65 (2.56) / mm ('') W Drilling tool holder, with shrink-fit mounting 8-25 Form A Mounting Shrink-fit mounting D8 internal, p max 80 bar X / Z 65 (2.56) / mm ('') W Drilling tool holder, with shrink-fit mounting 8-26 Form A Mounting Shrink-fit mounting D10 internal, p max 80 bar X / Z 65 (2.56) / mm ('') W Drilling tool holder, with shrink-fit mounting 8-27 Form A Mounting Shrink-fit mounting D12 internal, p max 80 bar X / Z 65 (2.56) / mm ('') W Drilling tool holder, with shrink-fit mounting 8-28 Form A Mounting Shrink-fit mounting D14 internal, p max 80 bar X / Z 65 (2.56) / mm ('') W Drilling tool holder, with shrink-fit mounting 8-29 Form A Mounting Shrink-fit mounting D16 internal, p max 80 bar X / Z 65 (2.56) / mm ('') For more information see H-4

49 Tool holder Shank HSK 40 Catalog page W Milling cutter holder 8-30 Form A Mounting Milling tool mounting D16 internal, p max 40 bar X / Z 45 (1.77) / mm ('') W Milling cutter holder 8-31 Form A Mounting Milling tool mounting D22 internal, p max 80 bar X / Z 50 (1.97) / mm ('') W Turning tool holder 8-32 Form T Mounting for CC.. 09T3.. external, p max 40 bar X / Z 80 (3.15) / mm ('') W Turning tool holder 8-33 Form T Mounting for CN external, p max 40 bar X / Z 80 (3.15) / mm ('') W Turning tool holder 8-34 Form T Mounting for DC.. 11T3.. external, p max 40 bar X / Z 80 (3.15) / mm ('') W Turning tool holder 8-35 Form T Mounting for DN external, p max 40 bar X / Z 80 (3.15) / mm ('') W Turning tool holder 8-36 Form T Mounting for VB external, p max 40 bar X / Z 80 (3.15) / mm ('') For more information see H-5

50 Tool holder Shank HSK 40 Catalog page W Basic holder 8-37 Form A Mounting internal, p max 80 bar X / Z 58 (2.28) / mm ('') W Boring head 8-38 Form Mounting for CC.. 09T3.. internal, p max 50 bar X / Z 45 (1.77) / 22 (0.87) mm ('') W Boring head 8-39 Form Mounting for CC.. 09T3.. internal, p max 50 bar X / Z 45 (1.77) / 22 (0.87) mm ('') W Boring head 8-40 Form Mounting for CN internal, p max 50 bar X / Z 32 (1.26) / 22 (0.87) mm ('') W Boring head 8-41 Form Mounting for CN internal, p max 50 bar X / Z 32 (1.26) / 22 (0.87) mm ('') W Boring head 8-42 Form Mounting for DC.. 11T3.. internal, p max 50 bar X / Z 32 (1.26) / 22 (0.87) mm ('') W Boring head 8-43 Form Mounting for DC.. 11T3.. internal, p max 50 bar X / Z 32 (1.26) / 22 (0.87) mm ('') For more information see H-6

51 Tool holder Shank HSK 40 Catalog page W Boring head 8-44 Form Mounting for DC.. 11T3.. internal, p max 50 bar X / Z 40 (1.57) / 22 (0.87) mm ('') W Boring head 8-45 Form Mounting for DC.. 11T3.. internal, p max 50 bar X / Z 40 (1.57) / 22 (0.87) mm ('') W Boring head 8-46 Form Mounting for DN internal, p max 50 bar X / Z 45 (1.77) / 22 (0.87) mm ('') W Boring head 8-47 Form Mounting for DN internal, p max 50 bar X / Z 45 (1.77) / 22 (0.87) mm ('') W Boring head 8-48 Form Mounting for VC internal, p max 50 bar X / Z 32 (1.26) / 22 (0.87) mm ('') W Boring head 8-49 Form Mounting for VC internal, p max 50 bar X / Z 32 (1.26) / 22 (0.87) mm ('') W Boring head 8-50 Form Mounting for VC internal, p max 50 bar X / Z 32 (1.26) / 22 (0.87) mm ('') For more information see H-7

52 Tool holder Shank HSK 40 Catalog page W Boring head 8-51 Form Mounting for VC internal, p max 50 bar X / Z 32 (1.26) / 22 (0.87) mm ('') W Calibrating tool 8-52 Form A Mounting D24 X / Z 180 (79) / mm ('') W Blanking plug 8-53 Form A Mounting D12 X / Z 50 (1.97) / mm ('') For more information see H-8

53 Accessories TRAUB TNX 65/42 Catalog page W IC Attachment 9-2 for internal cooling lubricant supply, 20 bar W IC Attachment 9-3 for internal cooling lubricant supply, 20 bar W IC Attachment 9-4 for internal cooling lubricant supply, up to 80 bar W IC Attachment 9-5 for internal cooling lubricant supply, up to 160 bar W Cover 9-6 W Seal 9-7 W End Plug 9-8 For more information, visit Z-1

54 Accessories TRAUB TNX 65/42 Catalog page Pin 9-9 AZ Replacement Seals for Tool Shank 9-10 AZ Sealing Washer and Mounting Pin 9-11 For more information, visit Z-2

55 Product notes Catalog page W EN Product note 10-2 External/internal cooling lubricant supply Drill holder with cylindrical shank tool mounting Offset set screws W EN Product note 10-3 Writestar W EN Product note 10-4 External/internal cooling lubricant supply Drill holder with collet chuck Offset set srew W EN Product note 10-5 External/internal cooling lubricant supply, lid convertible to IC 80 bar / 160 bar Offset set screws W EN Product note 10-6 WFB interface Mounting, cleaning and care, tightening torques W EN Product note 10-7 INDEX TRAUB CAPTO Live tools W EN 10-8 Product note INDEX TRAUB CAPTO Stationary tools For more information, visit Z-3

56 Product notes Catalog page W EN Product note 10-9 Gear cutting unit, adjustable angle Face contact flat For more information, visit Z-4

57 Technical Information TRAUB TNX 65/42 For more information, visit 1-1

58 Technical Information TRAUB TNX 65/42 Warranty When using tool holders that have not been set, checked and labeled accordingly by INDEX TRAUB, warranty is not applicable to the tool drive. Information on wear parts Tool holders and guide bushings are wear parts requiring correct handling. In order to ensure a long service life, compressed air or coolant must not enter the gap seals of the holders or of the guide bushings. Inspection of live tool holders and guide bushings Tool holders and guide bushings must be inspected at regular intervals (at least twice a year) for smooth running and play. The drive pinion and drive clutch of the live tool holders must be subjected to a visual inspection for damage or wear. If one of the above-mentioned defects is detected during the inspection of the tool holders or guide bushings, they must be returned immediately for preventive maintenance or repair to the following address: TRAUB Drehmaschinen GmbH & Co. KG Hauffstrasse 4 D Reichenbach, Germany Phone +49 (0) For more information, visit 1-2

59 Technical Information TRAUB TNX 65/42 Tool holders with cooling lubricant supply Tool holders marked with this symbol must be operated with cooling lubricant (no dry run permitted). Tool holders marked with this symbol must be operated with cooling lubricant when converting from external cooling lubricant supply to internal cooling lubricant supply. Observe dry run capability of IC attachment! lubricant filtering When using live tool holders with internal cooling lubricant supply, it is necessary to use a cooling lubricant filter system with a retained particle size 50 μ. Cleaning live tool holders Live tool holders must never be immersed in cleaning fluid since mixing the cleaning fluid with the bearing grease will reduce the service life of the tool holders. Speed ratio specifications on tool holders The value to be programmed is specified in the documentation and on the live tool holders ( = the input in the NC program). n prog = n tool x i n tool = speed at cutting tool edge n PROG = speed to be programmed i = speed ratio in the tool holder This means: the speed increase or speed reduction is not specified as a fraction but as a number. This gives speed increase ratios as numbers smaller than 1. Example: i = (corresponds to i = 1:3) i = (corresponds to i = 1:1.48) Step-down ratios result in numbers >1 For example: i = 2 (corresponds to i = 2:1) i = (corresponds to i = 4:3) For more information, visit 1-3

60 Technical Information TRAUB TNX 65/42 Direction of rotation specification Definition of the viewing direction. Viewing direction for determining the direction of rotation is always from behind (that is, from the drive direction) toward the shaft. On the machine side, the direction of rotation has been set by parameters such that M03 always denotes clockwise rotation and M04 counterclockwise run at the interface of the drive pinion of the tool holder. The direction of rotation given on the holder thus always refers to a "change in direction within a holder". M03 and M04 are machine functions to be programmed. The and arrows indicate the direction of rotation of the cutting edges. M03 M04 M04 M03 This means: No reversal of direction of rotation When the holder drive shaft has the same direction of rotation as the tool cutting edge, the clockwise direction of run must be specified by M03 (clockwise rotation). Accordingly, counter-clockwise run must be specified by M04. Reversal of direction of rotation When the holder drive shaft has the opposite direction of rotation as the tool cutting edge, the clockwise direction of rotation must be specified by M04. Accordingly, counter-clockwise run must be specified by M03. Example No reversal of direction of rotation M03 M04 For more information, visit 1-4

61 Technical Information TRAUB TNX 65/42 Tightening Torque The tightening torques of the clamping pieces to the tool holder mounting depends on the shank diameter of the tool holder. Shank size Ø 20mm Ø 25mm Ø 30mm Ø 40mm Tightening torque 8 Nm 20 Nm 25 Nm 40 Nm Replacement seals for tool shank See the accessories. The gaskets on the tool shank and the coolant bushing must be regularly checked for damages. Sealing air port It must be ensured on all machines with sealing air ports that the sealing air ports in the tool carrier and in the tool holders are sealed/ closed with M5x6 mm set screws. For more information, visit 1-5

62 Technical Information TRAUB TNX 65/42 Tool holders with fixation Except for very few cases, all tool holders have been preadjusted with high precision and sealed with the INDEX V bar / TRAUB adjusting bar / W-serration. This setting must not be changed. The INDEX V bar / TRAUB adjusting bar / W-serration ensures positional accuracy of the tool when re-inserted. The tool holders are fixed around the shank axis by pins (DIN 69880). DIN holders can be used. Double serration of the tool holders allows several uses. High-pressure unit The cooling lubricant up to 80 bar (e.g., for deep-hole drilling) is supplied through the standard cooling lubricant line. Load limits of live tools The drive power and torques are indicated in the performance charts. These values represent the upper limit of the calculated theoretical performance values (average values). In case of interrupted cuts, e.g., for milling, the load peaks occurring when the cutting edge enters the material may be much higher than the theoretical torque according to the performance chart. The cutter should be selected so that a cutting edge is constantly being used for cutting during the machining process. For more information, visit 1-6

Tool Holder Catalog INDEX ABC VDI 25 LL3602.30051-10.04.2014. 0414/Rö

Tool Holder Catalog INDEX ABC VDI 25 LL3602.30051-10.04.2014. 0414/Rö Tool Holder Catalog INDEX ABC VDI 25 LL3602.30051-10.04.2014 0414/Rö Disclaimer The illustrations in this documents may deviate from the delivered product. We reserve the right to make changes due to errors

More information

Driven Toolholders for SAUTER Turrets

Driven Toolholders for SAUTER Turrets Driven Toolholders for SAUTER Turrets Manufacturer of Precision Tools since 1974 INNOVATION PRECISION INDIVIDUALITY QUALITY SERVICE Table of Contents Type Page Driven Toolholders DIN 5482 - Disc-type Turrets

More information

About Us HAAS Tooling for CNC Turning Centers

About Us HAAS Tooling for CNC Turning Centers About Us WHO IS EPPINGER? Eppinger CNC tool holders to DIN 69880 are manufactured to precision levels far in excess of the required standards using advanced, patented produciton systems and facilities.

More information

Static and Driven Tools LB and LT Series

Static and Driven Tools LB and LT Series Static and Driven Tools LB and LT Series EWS Overview EWS Tool Technologies headquartered in Uhingen (Göppingen district) and with subsidiaries in the USA, South Korea and France belongs to the world wide

More information

L I V E T O O L F O R O K U M A

L I V E T O O L F O R O K U M A L I V E T O O L F O R O K U M A The Way to Success [Heimatec headquarters-germany] Heimatec is an international manufacturing company headquartered in Renchen, Germany. Heimatec s 40,000 square foot facility,

More information

4200 Malsbary Road Cincinnati, OH 45242 Phone (513) 984-5544 Fax (513) 984-5580

4200 Malsbary Road Cincinnati, OH 45242 Phone (513) 984-5544 Fax (513) 984-5580 PRECISION LIVE TOOLING & MACHINE TOOL ACCESSORIES MADE IN THE USA 4200 Malsbary Road Cincinnati, OH 45242 Phone (513) 984-5544 Fax (513) 984-5580 Patent Pending Live Tooling Planet Products Corporation

More information

Operating Instructions

Operating Instructions Operating Instructions Sauter Tooling for more information, please consult www., and for the complete standard tooling programme, please visit www.sauter-tools.com Sauter: The world turns with us! Table

More information

Precision made in Europe. As per DIN 8606. The heart of a system, versatile and expandable.

Precision made in Europe. As per DIN 8606. The heart of a system, versatile and expandable. 1 von 9 Precision made in Europe. As per DIN 8606. The heart of a system, versatile and expandable. Main switch with auto-start protection and emergency off. Precision lathe chuck as per DIN 6386 (Ø 100mm).

More information

KOMET. Adaptors Perfecting the Connection. With our comprehension programme of tool adaptors we have the right answer for every requirement.

KOMET. Adaptors Perfecting the Connection. With our comprehension programme of tool adaptors we have the right answer for every requirement. KOMET Adaptors Perfecting the Connection With our comprehension programme of tool s we have the right answer for every requirement. Adaptors with connections specified by manufacturers available on request.

More information

TOOL CLAMPING SYSTEMS

TOOL CLAMPING SYSTEMS TOOL CLAMPING SYSTEMS 2015/2016 We work for customers who have a weakness for our strengths. Companies intent on making a difference are obliged to develop constantly as well as deploy their strengths

More information

GM 300 CHECK- AND MEASURING INSTRUMENTS FOR OPTIMAL TOOL CLAMPING

GM 300 CHECK- AND MEASURING INSTRUMENTS FOR OPTIMAL TOOL CLAMPING GM 300 CHECK- AND MEASURING INSTRUMENTS FOR OPTIMAL TOOL CLAMPING AND lubrication Check- and Measuring instruments for optimal tool clamping and lubrication Pre-requisite for perfect machining results

More information

VDI Tool Holders. for Hardinge Machines. In USA, call: 800-843-8801 In Canada, call: 800-468-5946 Other, call: 607-734-2281 Fax: 607-734-8819

VDI Tool Holders. for Hardinge Machines. In USA, call: 800-843-8801 In Canada, call: 800-468-5946 Other, call: 607-734-2281 Fax: 607-734-8819 VI ool Holders for Hardinge Machines QUES 6/42, 8/51 and 10/65 CNC athes EIE 8/51 CNC athes HARINGE-EMAG V3/V5 Vertical CNC athes QUES WINURN 65 CNC urning Centers In USA, call: 800-843-8801 In Canada,

More information

Contents. VDI system. BMT system. 1. Driven Coupling Type DIN 1809 DIN 5480 DIN 5482 HAAS SPUR MT TOEM (BARUFFALDI) 1809 5480 MORI SEIKI

Contents. VDI system. BMT system. 1. Driven Coupling Type DIN 1809 DIN 5480 DIN 5482 HAAS SPUR MT TOEM (BARUFFALDI) 1809 5480 MORI SEIKI ISO 9001:2008 Contents 1. Driven Coupling Type VDI system DIN 1809 DIN 5480 DIN 5482 SPUR MT TOEM (BARUFFALDI) HAAS BMT system 1809 5480 MORI SEIKI 2. Turret Type Radial Turret Axial Turret 3. Driven Tool

More information

CAD 302.02.10.1 SK 30 1 10 (ER 16) 100 32 302.02.16.1 SK 30 2 16 (ER 25) 100 42 302.02.20.1 SK 30 2 20 (ER 32) 100 50

CAD 302.02.10.1 SK 30 1 10 (ER 16) 100 32 302.02.16.1 SK 30 2 16 (ER 25) 100 42 302.02.20.1 SK 30 2 20 (ER 32) 100 50 Spannfutter für Spannzangen DIN 6499 (ISO 15488) System ER Collet chucks for collets DIN 6499 (ISO 15488) ER-system Mandrins à pinces pour pinces DIN 6499 (ISO 15488) système ER Verwendung: Zur Aufnahme

More information

Quick Reference Catalog

Quick Reference Catalog Gearboxes Turrets Y-Axis Rotary Tools Tool Discs B-Axis Quick Reference Catalog WWW.BARUFFALDI.IT TB Servo Turret SERVO MOTOR TURRETS TB-type turrets rotate thanks to a BRUSHLESS SERVO MOTOR controlled

More information

DUGARD. Machine Tools Since 1939. Dugard 200HT / 200MC Slant Bed, High Precision CNC Lathes. www.dugard.com

DUGARD. Machine Tools Since 1939. Dugard 200HT / 200MC Slant Bed, High Precision CNC Lathes. www.dugard.com DUGARD Machine Tools Since 1939 Dugard 00HT / 00MC Slant Bed, High Precision CNC Lathes www.dugard.com Dugard 00HT / 00MC Hydraulic Tailstock Quill can be controlled by programme or manually, auto sensing

More information

ANSI APPROVED 04/11/2014 ANSI APPROVED 08/17/2011. 45 Reaffirmation ANSI APPROVED 02/28/2014. 45 Reaffirmation ANSI APPROVED 05/06/2013

ANSI APPROVED 04/11/2014 ANSI APPROVED 08/17/2011. 45 Reaffirmation ANSI APPROVED 02/28/2014. 45 Reaffirmation ANSI APPROVED 05/06/2013 STANDARDS STATUS REPORT As of November 4, 2015 Note: Dates in RED indicate the last action taken; Highlighted Items Indicate New/Open Items; Grey items have been closed Document TC Status Comments ASME

More information

DUGARD. Machine Tools Since 1939. Dugard 400 Slant Bed High Precision CNC Lathe. www.dugard.com

DUGARD. Machine Tools Since 1939. Dugard 400 Slant Bed High Precision CNC Lathe. www.dugard.com DUGARD Machine Tools Since 1939 Dugard 400 Slant Bed High Precision CNC Lathe www.dugard.com Superb Performance, Maximum Stability, Maximum Reliability Precision, Power and Capacity Make the Dugard 400

More information

DUGARD. Machine Tools Since 1939. Dugard 700L Series Heavy Duty CNC Lathes. www.dugard.com

DUGARD. Machine Tools Since 1939. Dugard 700L Series Heavy Duty CNC Lathes. www.dugard.com DUGARD Machine Tools Since 1939 Dugard 700L Series Heavy Duty CNC Lathes www.dugard.com Dugard 700L Heavy Duty CNC Lathe 2000, 3000 or 4000mm bed length Designed for easy and convenient operation The concave

More information

Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors

Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors 20000 Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 823 Notes 824 Technical

More information

[ means: Save time, money and space! MAXXMILL 500. Vertical milling center for 5-side machining

[ means: Save time, money and space! MAXXMILL 500. Vertical milling center for 5-side machining [ E[M]CONOMY] means: Save time, money and space! MAXXMILL 500 Vertical milling center for 5-side machining MAXXMILL 500 MAXXMILL 500 is the ideal vertical milling center for the for the 5-axis operation

More information

Alfra Rotabest 100 Metal Core Drilling Machine. Operation Manual

Alfra Rotabest 100 Metal Core Drilling Machine. Operation Manual Alfra Rotabest 100 Metal Core Drilling Machine Operation Manual 06/2005 1. Technical Data Prod. No.: 18630 Name : Rotabest 100 Input: Load rpm: 1800 Watt 110/175/245/385 rpm Tool Holder : MT 3 Coolant

More information

Machine tools. Milling- and boring machines

Machine tools. Milling- and boring machines Milling- and boring machines Milling- and boring machines Our family owned company develops and manufactures customized machines and designs machine tools based on work piece requirements successfully

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)

Volkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17) 17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure

More information

3-Component Measuring System

3-Component Measuring System Force 3-omponent Measuring System for utting Force Measurement During Turning Modular system for measurement of cutting forces when turning outside and inside diameters on turret lathes. Machine adapters

More information

Precise heavy-duty cutting

Precise heavy-duty cutting PR 130 / PR 150 / PR 160 / PR 180 / PR 200 / PR 260 Precise heavy-duty cutting P-SERIES K-SERIES T-SERIES MILLFORCE 02 / Fields of application 03 / Machine concept 04 / Machine technology 05 / Options

More information

turning instead of measuring

turning instead of measuring PARAT -way-indexing-quickchange turret-toolpost turning instead of measuring Indexing accuracy 0,005 mm (0,0002 ) Internal and external operations in one setting Quick-clamping System with 0 Positions

More information

413 NOVA SYSTEM PAN AMERICAN TOOL CORPORATION 5990 NW 33309-2208 PHONE (954)735-8665 TOLL FREE 1-800-423-2764 FAX

413 NOVA SYSTEM PAN AMERICAN TOOL CORPORATION 5990 NW 33309-2208 PHONE (954)735-8665 TOLL FREE 1-800-423-2764 FAX 413 NOVA SYSTEM 5990 NW 31st Avenue Ft. Lauderdale, Florida 33309-2208 PHONE (954)735-8665 TOLL FREE 1-800-423-2764 FAX (954)735-8668 2013 Pan American Tool Corporation 2013 TERMS AND CONDITIONS TERMS:

More information

TL-Series Sub-Spindle Operator s Addendum

TL-Series Sub-Spindle Operator s Addendum 3 4 5 11 9 TL-Series Sub-Spindle Operator s Addendum 2 1 12 10 6 7 8 20HP VECTOR DUAL DRIVE LIVE TOOLING SUB SPINDLE 2008 Haas Automation, Inc. 96-0037 rev L 9/08 1 1. Introduction Specific M codes are

More information

Home"" """"> ar.cn.de.en.es.fr.id.it.ph.po.ru.sw

Home > ar.cn.de.en.es.fr.id.it.ph.po.ru.sw Home"" """"> ar.cn.de.en.es.fr.id.it.ph.po.ru.sw Milling of Grooves, Elongated Slots and Break-throughs - Course: Techniques for machining of material. Trainees' handbook of lessons (Institut fr Berufliche

More information

CNC Portal Milling Machine FZ 50. CNC Power Milling Technology

CNC Portal Milling Machine FZ 50. CNC Power Milling Technology CNC Portal Milling Machine FZ 5 CNC Power Milling Technology FZ 5 Portal Milling Machine for Heavy Cutting The newly developed portal milling machine FZ 5 is based on a flexible machine design which can

More information

YUASA MILLING MACHINE ACCESSORIES & TOOLS

YUASA MILLING MACHINE ACCESSORIES & TOOLS 97 HORIZONTAL / VERTICAL 5C COLLET INDEX 550 series 2 YEAR WARRANTY Spindle is manufactured with a taper seat in body frame. Rapid opening and closing is performed with a level collet closer with a leverage

More information

Providing Answers For All Your Machine Tool Needs

Providing Answers For All Your Machine Tool Needs Providing Answers For All Your Machine Tool Needs STANDARD FEATURES FANUC MXP-200FA CONTROL Spindle Features Body Structure POWERFUL 20 HP H / L SHIFTING SPINDLE MOTOR HARDENED & GROUND BOXWAY CONSTRUCTION

More information

indexable Center Drill

indexable Center Drill Our innovative tooling design upgrades productivity and competitive capability while reducing production requirements in a range of industries. The tooling system is designed to benefit users of machining

More information

These Installation Instructions are valid for antennas in the following version:

These Installation Instructions are valid for antennas in the following version: Installation Instructions 4 ft CompactLine Antennas (with E-Mount 250 km/h) SB, SBX NMT 560-05(e) These Installation Instructions are valid for antennas in the following version: Reflector Ø 1.2 m (4 ft)

More information

That s E[M]CONOMY: Not just training: Real Action! CONCEPT TURN 250. Training reality with industrial performance

That s E[M]CONOMY: Not just training: Real Action! CONCEPT TURN 250. Training reality with industrial performance [ That s ] E[M]CONOMY: Not just training: Real Action! CONCEPT TURN 250 Training reality with industrial performance Concept TURN 250 Uncompromising quality right down to the last bolt, at an unbeatable

More information

QUICK-CHANGE tool system for multi-tasking and turning lathes

QUICK-CHANGE tool system for multi-tasking and turning lathes System solution from SISSTOOLS Tool system for upper turning-/milling spindles System solution from SISSTOOLS Increase productivity by reducing nonproductive time Very quick tool changing time SISS TOOLS

More information

DUGARD. Machine Tools Since 1939. Dugard ECO Series Driven Tool, Slant Bed CNC Lathes. www.dugard.com

DUGARD. Machine Tools Since 1939. Dugard ECO Series Driven Tool, Slant Bed CNC Lathes. www.dugard.com DUGARD Machine Tools Since 1939 ECO Series Driven Tool, Slant Bed CNC Lathes www.dugard.com ECO Series - CNC Lathes Amazing speed, power, precision and durability all at an affordable price Rigid and Trustworthy

More information

IMPORTANT DOCUMENTATION DO NOT DISCARD!

IMPORTANT DOCUMENTATION DO NOT DISCARD! PART NO.: 6441-263C SERIES GRT 3 JAW PARALLEL GRIPPERS INFORMATION SHEET IMPORTANT DOCUMENTATION DO NOT DISCARD! Use this information sheet to assist with gripper installation and setup. File with maintenance

More information

ECO 80 PRODUCT DESCRIPTION FEATURES. Power output S1 100% Adjustable air nozzle. Liquid cooling. Minimalmengenschmierung MMS retrofit

ECO 80 PRODUCT DESCRIPTION FEATURES. Power output S1 100% Adjustable air nozzle. Liquid cooling. Minimalmengenschmierung MMS retrofit A PRODUCT DESCRIPTION Power output S6 40% Power output S1 100% Rotation speed Diameter Spindlehousing Spindle interface 3.0 kw 2.5 kw to 40.000 rpm 80 mm Stainless steel HSK - E25 FEATURES Adjustable air

More information

SAMSUNG Machine Tools PL60 CNC TURNING CENTER

SAMSUNG Machine Tools PL60 CNC TURNING CENTER SAMSUNG Machine Tools PL60 CNC TURNING CENTER SAMSUNG'S Advanced Engineering and Machine Design Cast iron structure for superior dampening characteristics and thermal displacement Rigid 45 degree slant

More information

HYDRO-FIX hydraulic clamping system. For boring bars and driven tools

HYDRO-FIX hydraulic clamping system. For boring bars and driven tools HYDRO-FIX hydraulic clamping system For boring bars and driven tools Improve your productivity HYDRO-FIX hydraulic clamping system has successfully been used for over 15 years. HYDRO-FIX is excellent for

More information

Machine Tool Practices, 8th Edition 2006 Correlated to: South Carolina Manufacturing Course Standards for Machine Technology 1, 2, 3, 4

Machine Tool Practices, 8th Edition 2006 Correlated to: South Carolina Manufacturing Course Standards for Machine Technology 1, 2, 3, 4 62300100 A. PERFORMING WORK SAFETY PRACTICES 62300101 Demonstrate the ability to work safely. SE: p.6-13, 208-210, 233-235 TE: Manual p.11-12, 51-52, 55-58 TECH: CD Shop Safety: PowerPoint Slides 1-8 62300102

More information

Compensation Unit in X-, Y-, and Z-Direction AGE-S-XYZ 100-200

Compensation Unit in X-, Y-, and Z-Direction AGE-S-XYZ 100-200 Translation of the original manual Compensation Unit in X-, Y-, and Z-Direction AGE-S-XYZ 100-200 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains

More information

HIGH SPEED SPINDLE MOTORS

HIGH SPEED SPINDLE MOTORS DATA SHEET HM / HT and ES Ranges HIGH SPEED SPINDLE MOTORS Manual and Automatic Tool Change Compact, high speed, asynchronous motors with power ratings from 0.65 to 18 designed to provide long term reliability

More information

Ultra Live Center RN. Clamping tools for clamping on machine tools. NEIDLEIN revolving ultra live centers type RN ensure: Type RN with morse taper

Ultra Live Center RN. Clamping tools for clamping on machine tools. NEIDLEIN revolving ultra live centers type RN ensure: Type RN with morse taper Ultra Live Center RN Type RN with morse taper NEIDLEIN ultra live centers are designed for employment in turning, grinding and other production machines. Owing to the application of bearing and the stable

More information

TRIMMING UNIT/DIAMOND MACHINE TST.13

TRIMMING UNIT/DIAMOND MACHINE TST.13 TRIMMING UNIT/DIAMOND MACHINE TST.13 REFERENCE BOOK rel. 02.15 TRIMMING UNIT/DIAMOND MACHINE TST.13 REL. 02.15 ENGLISH LANGUAGE 1 MACHINE DESCRIPTION TST.13 was designed and built for processing methacrylate.

More information

Driven & Static Tooling HAAS

Driven & Static Tooling HAAS Driven & Static Tooling HAAS Haas Driven & Static Haas Tools 3 Table of Contents Haas Tooling SL20, SL30 Standard VDI Turret Driven Tools SL20, SL30 Haas Turret Driven Tools SL20, SL30, TL15, TL25 Hyrbid

More information

ŠKODA MACHINE TOOL HORIZONTAL MILLING AND BORING MACHINES ŠKODA HCW

ŠKODA MACHINE TOOL HORIZONTAL MILLING AND BORING MACHINES ŠKODA HCW ŠKODA MACHINE TOOL HORIZONTAL MILLING AND BORING MACHINES ŠKODA HCW KODA HCW TRADITION AND EXPERIENCE The ŠKODA machine tools of different types and design have been present in the world market since the

More information

Table of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19

Table of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19 Table of Contents Overview 1 Pump Disassembly 2 Control Disassembly / Reassembly 7 Pump Reassembly 13 Adjustment Procedures DR Control 19 Adjustment Procedures DRG Control 20 Adjustment Procedures DFR

More information

Step-by-step instructions:

Step-by-step instructions: Spark plug thread repair for Ford Triton cylinder heads Step-by-step instructions: Identification Installation Verification Specifically designed and tested for 4.6L, 5.4L, and 6.8L 2 and 4 valve heads,

More information

Signature Norman Crepeau Special Condition Subject to prior sale Johnford ST60B. CNC Turning Center

Signature Norman Crepeau Special Condition Subject to prior sale Johnford ST60B. CNC Turning Center Mr. Will Rood B & B Precise Products 25 Neck Road Benton, ME 04901 Date June 3, 2008 Quote # 06032008 Valid for 30 Days Quoted by Norman Signature Norman Crepeau Special Condition Subject to prior sale

More information

T-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5. www.thomsonlinear.com

T-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5. www.thomsonlinear.com T-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5 www.thomsonlinear.com Version History Edition Number Edition Date Reason for Revision 1 2004 First edition

More information

DATA PD-500-000. SV13.., SV14.. Levelling Valves. Product. Function. Technical Features. Range Overview

DATA PD-500-000. SV13.., SV14.. Levelling Valves. Product. Function. Technical Features. Range Overview Commercial Vehicle Systems Product DATA SV.., SV.. Doc. No. Y075 (Rev. 00) PD-500-000 Function On vehicles fitted with air suspension, the Levelling Valve ensures that the axle suspension air bags maintain

More information

Repair of Hyd-ro-ac Actuators

Repair of Hyd-ro-ac Actuators Repair of Hyd-ro-ac Actuators OVERHAUL INSTRUCTIONS SS-.2A-1V SS-.5A-1V SS-.5A-2V Read the entire contents of these instructions before installing the actuator and before making any connections to the

More information

P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc

P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center

More information

Round Housing with Side Ports

Round Housing with Side Ports Power Steering Steering Control Unit (SCU) Parts and Repair Information 5 Series Steering Control Units 001 Square Housing with Side Ports Round Housing with Side Ports T E L RP Round Housing with End

More information

UNITED STATES CUTTING TOOL INSTITUTE Product Groupings for Standards Activities CUTTING TOOL PRODUCTS

UNITED STATES CUTTING TOOL INSTITUTE Product Groupings for Standards Activities CUTTING TOOL PRODUCTS CUTTING TOOL PRODUCTS 1. BORING ISO 5609 Boring bars for indexable inserts Dimensions ISO 6261 Boring bars (tool holders with cylindrical shank) for indexable inserts Designation JIS B 4128 Boring bars

More information

Milling Chuck Features

Milling Chuck Features Milling Chuck Features Since its first introduction into the industry in 1963, Nikken has sold over 2,000,000 worldwide and never stopped improving its original design. Featuring multi-roller bearings

More information

RAPID DIAL TEST INDICATORS

RAPID DIAL TEST INDICATORS RAPID DIAL TEST INDICATORS The Verdict Rapid presents the dial face inclined to the workpiece surface ensuring good visual accessibility obviating parallax error. Rapids incorporate a rear swivel spigot

More information

www.dreiling-maschinenbau.com Tel.: +49 (0) 36084 / 840-1100 Email: info@dreiling-maschinenbau.com

www.dreiling-maschinenbau.com Tel.: +49 (0) 36084 / 840-1100 Email: info@dreiling-maschinenbau.com www.dreiling-maschinenbau.com Tel.: +49 (0) 36084 / 840-1100 Email: info@dreiling-maschinenbau.com Dreiling tool Shuttle system for a heavy duty milling machine (China) Dreiling Technical Data of the System:

More information

Mandrel system MIS. www.microcentric.de

Mandrel system MIS. www.microcentric.de Mandrel system MIS MicroCentric GmbH Berblingerstr. 16 71254 itzingen / Germany Tel.: +49 (0) 7156 17819-0 Fax: +49 (0) 7156 17819-20 E-Mail: info@microcentric.de www.microcentric.de Products in this catalog:

More information

CNC Vertical Machining Center Alpha-Center HD Heavy cast iron design, precise guideways, high-performance gear designed for heavy machining

CNC Vertical Machining Center Alpha-Center HD Heavy cast iron design, precise guideways, high-performance gear designed for heavy machining CNC Vertical Machining Center Alpha-Center HD Heavy cast iron design, precise guideways, high-performance gear designed for heavy machining Optional spindle package: 31 kw maximum power 870 Nm max. torque

More information

SITEMA PowerStroke. Technical Information TI-P12. 1 Function. 2 Applications. Mould Closing Devices series FSKP. Contents

SITEMA PowerStroke. Technical Information TI-P12. 1 Function. 2 Applications. Mould Closing Devices series FSKP. Contents SITEMA PowerStroke FSP ocking, actuating and releasing by pneumatic pressure English translation of German original Technical Information TI-P1 SITEMA PowerStroke Mould Closing Devices series FSP drive

More information

SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27A

SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12 DUAL BEVEL COMPOUND MITER SAW B27A PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510

More information

StarChip 400. StarChip 400. More productive, more cost-effective - the Inclined Bed Lathe StarChip. CNC Inclined Bed Lathe. www.knuth.

StarChip 400. StarChip 400. More productive, more cost-effective - the Inclined Bed Lathe StarChip. CNC Inclined Bed Lathe. www.knuth. CNC Inclined Bed Lathe More productive, more cost-effective - the Inclined Bed Lathe StarChip Center width 550 mm Turning diameter over bed (max) 360 mm Speed range 50-6000 min -1 8-station tool turret

More information

means: Multitasking at its best. HYPERTURN 95/110 The new generation of multitasking machines for the highest levels of productivity and flexibility

means: Multitasking at its best. HYPERTURN 95/110 The new generation of multitasking machines for the highest levels of productivity and flexibility [ E[M]CONOMY] means: Multitasking at its best. HYPERTURN 95/110 The new generation of multitasking machines for the highest levels of productivity and flexibility HYPERTURN 95/110 [Main spindle] [Control

More information

TA-A BED TYPE MILLING CENTRE

TA-A BED TYPE MILLING CENTRE TA-A BED TYPE MILLING CENTRE TA-A BED TYPE MILLING CENTRE MILLING CENTRE HIGH CAPACITY IN A COMPACT MACHINE High stock removal capacity TA-A BED TYPE MILLING CENTRE 2 TA-A The TA-A milling centre is a

More information

Static Toolholders for CNC Turning Machines

Static Toolholders for CNC Turning Machines Static Toolholders for CNC Turning Machines Table of Contents Type Page Combi Toolholder Boring Bar Holder Turning Tool Holder Combi Outer Turning Toolholder Combi Turning Toolholder for facing QUICK TURN

More information

SITEMA PowerStroke. Technical Information TI-P11. 1 Function. 2 Applications. Mould Closing Devices series FSK. Contents

SITEMA PowerStroke. Technical Information TI-P11. 1 Function. 2 Applications. Mould Closing Devices series FSK. Contents English translation of German original Technical Information TI-P11 SITEMA PowerStroke Mould Closing Devices series FS drive system for powerful forces on a short stroke hydraulic actuation closing force

More information

SmartCut EVS Series CNC Mills Combination of CNC technology and manual capability SC EVS-350B CNC SC EVS-550B CNC

SmartCut EVS Series CNC Mills Combination of CNC technology and manual capability SC EVS-350B CNC SC EVS-550B CNC Summit Machine Tool Manufacturing L.L.C. SmartCut EVS Series CNC Mills Combination of CNC technology and manual capability SC EVS-350B CNC SC EVS-550B CNC Summit Machine Tool Manufacturing L.L.C. SmartCut

More information

Tooling technology. BENZ LinTec broaching units + for turning centers / lathes + for machining centers METAL MACHINING. www.benz-tools.

Tooling technology. BENZ LinTec broaching units + for turning centers / lathes + for machining centers METAL MACHINING. www.benz-tools. Tooling technology BENZ LinTec broaching units + for turning centers / lathes + for machining centers METAL MACHINING AT BENZ WERKZEUGSYSTEME, OUR MAXIM, "INNOVATION. PRECISION. PASSION." IS FAR MORE THAN

More information

EC303 0608701017 50 1/4" quickchange 0608800630 EC303 0608701017 740. 3GE27 0608720053 50 3/8" square with 0608800631 EC303 0608701017 1.

EC303 0608701017 50 1/4 quickchange 0608800630 EC303 0608701017 740. 3GE27 0608720053 50 3/8 square with 0608800631 EC303 0608701017 1. 2 Bosch Rexroth AG Electric Drives and Controls Documentation Output drives Measurement transducer Gearboxes EC motor Advantages: For tight drill holes Standard tool mounts Flange connection for easy assembly

More information

N20xxA, N34xxA NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR FLOATING AND 2-POSITION CONTROL

N20xxA, N34xxA NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR FLOATING AND 2-POSITION CONTROL N2xxA, N34xxA NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR FLOATING AND 2-POSITION CONTROL SPECIFICATIONS Supply voltage N224A / N3424A N223A / N3423A PRODUCT DATA 24 Vac 15%, 5/6 Hz 23 Vac 15%,

More information

The Boxford range of 3-axis CNC Machining Centres are

The Boxford range of 3-axis CNC Machining Centres are The Boxford range of 3-axis CNC Machining Centres are requirements. Featuring a high-end machine controller, utilising the latest motion control technology, they can satisfy all your 2½ and 3D milling

More information

SCP 012-130 ISO. Other advantages: SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics.

SCP 012-130 ISO. Other advantages: SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics. SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics. SCP 012-130 ISO covers the entire displacement range 12-130 cmᶟ rev. at a maximum pressure of

More information

Machine needle shut-off nozzle type-a

Machine needle shut-off nozzle type-a Machine needle shut-off nozzle type-a spring operated Applications: Thermoplastics (not applicable for PVC) Shut-off mechanism: Operated with one axial high performance spring Index of contents Chapter

More information

Flexible High Tech Solutions for Industry

Flexible High Tech Solutions for Industry Vertical machining centre f milling and turning Flexible High Tech Solutions f Industry Those who look a little harder discover a lot me Machine Tools EN Customized Efficiency Machine Tools MAXIMA 12 K16/3

More information

BED TYPE MILLING CENTRE

BED TYPE MILLING CENTRE TR BED TYPE MILLING CENTRE TR BED TYPE MILLING CENTRE BED TYPE MILLING CENTRE HIGH PERFORMANCE IN A COMPACT MACHINE PROVIDING ACCURATE COMPLEX MILLING TR BED TYPE MILLING CENTRE The TR milling centre is

More information

CORE COMPETENCY REQUIREMENTS NIMS CERTIFIED CNC SET UP PROGRAMMER MILLING AND TURNING

CORE COMPETENCY REQUIREMENTS NIMS CERTIFIED CNC SET UP PROGRAMMER MILLING AND TURNING CORE COMPETENCY REQUIREMENTS NIMS CERTIFIED CNC SET UP PROGRAMMER MILLING AND TURNING APPRENTICE CORE COMPETENCIES 1. Identify and Demonstrate Usage of Machine Safety and Personal Protective Equipment

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION P 1 / 5 Model No. Description 8390D Cordless Percussion Driver Drill 13mm CONCEPT AND MAIN APPLICATIONS Model 8390D has been developed by adding percussion mechanism to Model 6390D.

More information

SAMSUNG Machine Tools

SAMSUNG Machine Tools SAMSUNG Machine Tools LCV 55 / 65 / 8 VERTICAL MACHINING CENTERS SMEC Co., Ltd. 6671, Gasulri, Daesanmyeon, Changwonsi Gyeongsangnamdo, Korea 641921 Tel +82 55 25 4832(48) Fax +82 55 25 491(492) http://www.esmec.com

More information

Mercedes 722.3 722.4

Mercedes 722.3 722.4 96 Mercedes 7. 7. 5 6 7 8 - Clutch K - Brake Band B - Disc Brake B - Wide Planet Pinion 5 - One-Way Clutch F 6 - Clutch K 7 - Brake Band B 8 - Narrow Planet Pinion Int. Band Fwd. Band Rev. Clutch Direct

More information

Driven & Static CONTENT. Overview... Mazak Tooling... Mori Seiki Tooling... Nakamura Tooling... Driven & Static. Tooling Rebuild service...

Driven & Static CONTENT. Overview... Mazak Tooling... Mori Seiki Tooling... Nakamura Tooling... Driven & Static. Tooling Rebuild service... 205 CONTENT 207 Citizen Tooling.............. 209 Daewoo Tooling............. 217 Haas Tooling................ 221 Mazak Tooling............... 223 Mori Seiki Tooling.......... 249 Nakamura Tooling..........

More information

The teach-in lathe. New generation SE

The teach-in lathe. New generation SE The teach-in lathe New generation SE New generation SE Description Friendly user lathes with high chip removal capacity The SE Series combines the working capacity of a conventional lathe with the advantages

More information

ORTHOBLOC 3000. Drive systems. Installation. This manual is to be given to the end user. 3996 en - 2013.04 / k. R max - 5 mm.

ORTHOBLOC 3000. Drive systems. Installation. This manual is to be given to the end user. 3996 en - 2013.04 / k. R max - 5 mm. en - 01.0 / k 1 en This manual is to be given to the end user --> B7 (0 to 0 ) R max - mm R min + mm ORTHOBLOC 000 Installation LEROY-SOMER Ot 000 en - 01.0 / k NOTE LEROY-SOMER reserves the right to modify

More information

VCE VET ENGINEERING STUDIES

VCE VET ENGINEERING STUDIES Victorian Certificate of Education 2013 SUPERVISOR TO ATTACH PROCESSING LABEL HERE STUDENT NUMBER Letter Figures Words VCE VET ENGINEERING STUDIES Written examination Section Wednesday 20 November 2013

More information

Advantages and application of PCD and CBn tools

Advantages and application of PCD and CBn tools PCD and CBN tools Advantages and application of PCD and CBn tools Powerful and economical Tools with PCD and CBN cutting edges are the ideal solution for difficult-to machine, highly abrasive materials.

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47) 47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing

More information

BoWex SD, SD1 and SD2 Operating-/Assembly Instructions

BoWex SD, SD1 and SD2 Operating-/Assembly Instructions D-807 Rheine 0111 E 1 curved-tooth gear couplings are flexible shaft connections. They are able to compensate for shaft displacement caused by, as an example, inaccuracies in production, heat expansion,

More information

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17) 17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning

More information

Pneumatic Control and Shut-off Butterfly Valve Pfeiffer Type BR 14b/31a and Type BR 14c/31a

Pneumatic Control and Shut-off Butterfly Valve Pfeiffer Type BR 14b/31a and Type BR 14c/31a Pneumatic Control and Shut-off Butterfly Valve Pfeiffer Type BR 14b/31a and Type BR 14c/31a Application Tight-closing, double eccentric butterfly valve for process engineering and plants with industrial

More information

APEX DYNAMICS, INC. APEX DYNAMICS INC.,

APEX DYNAMICS, INC. APEX DYNAMICS INC., APEX DYNAMICS, INC. Single Motor Power Tool Turret APEX DYNAMICS, INC. APEX DYNAMICS INC., established in 1987 in Taiwan, has developed into a world-leading manufacturer of servomotor driven robot and

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Models No. 2012NB Description 304mm (12") Automatic Thickness Planer CONCEPTION AND MAIN APPLICATIONS * Compact and light weight (27 Kg./59 lbs) automatic thickness planer for easier

More information

DRIVEN and STATIC TOOLING For OKUMA VDI30 (LB200-LT200-GENOS L200M-LT10M)

DRIVEN and STATIC TOOLING For OKUMA VDI30 (LB200-LT200-GENOS L200M-LT10M) DRIVEN and STATIC TOOLING For OKUMA VDI30 (LB200-LT200-GENOS L200M-LT0M) 039 BERGIN RD. HOWELL, MI 48843 PHONE : 877-9-TOOLS ( 80-632-4446 ) FAX: 877-92-TOOLS ( 80-632-4467 ) EMAIL: info@mdtooling.com

More information

Volkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing

Volkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed Gearshift cable/lever installing Gearshift housing repairing Gearshift lever repairing lever/relay lever, installing Gearshift mechanism

More information

BIG POWER! Large FEC-50 FTARH 50. Grande puissance - Grosser Leistung SLIM LINE POWER. Spindle Extention. Spindle Speeder

BIG POWER! Large FEC-50 FTARH 50. Grande puissance - Grosser Leistung SLIM LINE POWER. Spindle Extention. Spindle Speeder Large Grande puissance - Grosser FEC-50 Manual and NC controlled Manual or automatic tool change 30 to 100 2000 kg 100 FTARH 50 BIG POWER! Manual and NC controlled 32 515 kg 1'500 3'000 30 to 50 SLIM LINE

More information

Table of contents CAT DISC 25. Mower

Table of contents CAT DISC 25. Mower Mower CAT DISC 25 ( Type PTM 370 : +.. 01001 ) Excerpt from operating manual Nr. 0370B00C.pdf Table of contents Swath Discs... 13 Swath Boards... 13 Safety points... 14 General maintenance hints... 14

More information

Reaction Torque Sensor

Reaction Torque Sensor Force 1 1 N m up to 1 000 1 000 N m Type 9329A 9389A These easy to install piezoelectric reaction torque sensors are particularly suitable for measuring rapidly changing torques at non-rotating shafts.

More information

Loewe GK Installation and operating manual

Loewe GK Installation and operating manual SCHMIDT-KUPPLUNG GmbH Loewe GK Installation and operating manual Loewe GK Loewe GK: angular and radial displacement compensation combined with axial stiffness. The compact coupling combines angular and

More information