Panelboards 11 PANELBOARDS. Type P2 Panelboards. General

Transcription

1 General Features Flexibility is the hallmark of the P2 panel. This panel offers a wide array of factoryassembled options to meet almost all lighting panel applications. With this design, the ability to mix breaker frames in unit space up to 250 amps will also meet many distribution panel requirements in a much smaller package. Bussing options for the P2 vary from the typical temperature rated to 750 A/Si aluminum to 1000A/Si copper. Standard bussing in the P2 panel is tin-plated. Silver-plated copper is also offered as an option. Integrated time clocks, bus mounted contactors, as mains or sub mains, split bus, and subfeed lugs (up to amp) are just a few of the options of this unique panel. Like a lighting panel, P2 is set up around 18, 30, 42, 54,, 78, and 90 circuit configurations. It will also allow the user to configure the panel to the smallest possible size. The P2 panel starts with 9" of unit space (18 circuits of 1" pole breakers). Breakers mounted in unit space can be mixed and matched to meet customer requirements. All 1" pole breakers (BL, BQD, ED frames) are mounted in 3" or " pole increments. Breaker frames, above amps, are mounted in " single breaker mountings. As an example of a minimum panel, () 20 amp 1-pole BL breakers (3" of unit space) and a 3-pole 225 amp QJ breaker (" of unit space) equaling 9" of unit space can be configured in a P2 panel without any extra provisions or space required. FD 250 amp and JD amp breakers are mounted as subfeed breakers outside of unit space. Another unique feature of the P2 panel is that blank unit space can be added to allow for future expansions or modifications. Any expansions or modifications must be in 3" increments. BL, BQD, and ED frame breakers have 3" or " pole kits, and can be mixed in unit space by these increments. Breakers of the same frame can cross from one mounting to another if contiguous. QJ frame breakers are mounted in " increments for two- and three pole, single mounted units. Changes in the unit space length for BL, BQD, or ED frame breakers require an addition deadfront, center strip kit. Check with sales or the factory for additional unit space kits. Main Lug / Main Breaker Enclosure Standard Type 1 enclosure is 20" wide x 5.75" deep X. Box Height is determined by main device and unit space. See charts for box height. Voltage 00V AC max. 250V DC max. Amperage 00 amp max. Short circuit rating 200 KAIC max. symmetrical or equal to the lowest rated device installed unless a series rating is indicated. Panels with subfeed or feed-thru lugs without a main device, circuit breaker or fusible unit, are limited to a three-cycle rating. The three-cycle rating for the P2 panel is limited to 22 KAIC. Note that the main device may be mounted remote from the panel. Bussing The P2 panel has more options to meet market requirements. The standard bussing is temperature rated aluminum. The rating is per the requirements of UL 7 the standard for panelboards. All aluminum bussing is tin-plated. Optional bussing for the P2 panel is: 750 A/Si aluminum, temperature rated copper, and 1000 A/Si copper. The copper bus option for this panel is tin-plated. Weight Approximate Total panelboard weight when filled with a normal quantity of breakers and accessories is about 3 lbs. (1 kg) per inch (54g per mm) of box height. Gauge Steel of Boxes Fronts, Surface and Flush Dimensions in inches (mm) Gauge Steel Width Height Box Front 20 (508) 2 74 (0 1880) #1 #14 Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog 11-23

2 11 PANELBOARDS Panelboards Standard Circuit P2 Panels /Dimensions Base Box Size Requirements for P2 Panels with Standard Line Lugs, and fewer than 55 poles of 1" module (BL,BQD, ED, xgb) branch breakers and provisions. Unit Spaces range from 9" to 45" (in " increments). Boxes range from 2" to 74" high (in " increments). Inclusion of optional modifications may require size increases that must be added to these base values to calculate the final box size for the panel (see pages 11-29, 11-30). Vertical Main breaker options with the designation are added-price options (see page 11-2). Values in brackets [ ], at the bottom of each column, indicate the maximum allowable 1" module branch poles for each main type. P2 Panels with Standard Line Lugs. Unit Space (starting with 9" and adding " increments) A Dimension B Dimension Box Height Main Lugs A A 00A Main Breakers A BL, BQD, xgb, ED A ED A CED 225A QJ 225A QJ FD FD CFD A JD A CJD [54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [42p] [54p] [42p] 00A LD 00A CLD Extended Circuit P2 Panels Base box size requirements for Extended Circuit P2 Panels with Standard Line Lugs, and 55 or more poles of 1" module (BL,BQD, ED, xgb) branch breakers and provisions. Unit Spaces range from 33" to 45" (in " increments). Boxes range from 5" to 74" high (in " increments). Inclusion of optional modifications may require size increases that must be added to these base values to calculate the final box size for the panel (see pages 11-29, 11-30). Vertical Main breaker options with the designation are added-price options (see page 11-2). Values in brackets [ ], at the bottom of each column, indicate the maximum allowable 1" module branch poles for each main type. P2 Panels with Standard Line Lugs. Unit Space (starting with 9" and adding " increments) A Dimension B Dimension Box Height Main Lugs A A 00A Main Breakers A BL, BQD, xgb, ED A ED A CED 225A QJ [90p] [90p] [90p] [90p] [90p] [90p] [90p] [90p] [78p] [p] [54p] [p] [42p] [54p] [42p] Note: The vertical main breaker application for ED, QJ, and FD adds " of box height. 225A QJ FD FD CFD A JD A CJD 00A LD 00A CLD Main breaker wire bending space diagram Main lug wire bending space diagram Box depth = 5.75 in. (14 mm) Box width 20 in. (508 mm) for A Box depth = 5.75 in. (14 mm) Box width 20 in. (508 mm) for A Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog

3 Standard Circuit P2 Panels Main Breaker Wire Bending Standard Circuits (up to 54 1" module branch poles) Panel Amps Breaker Frames C D 100 BL BQD NGB, HGB, LGB ED (horiz.) ED (vert.) QJ (horiz.) QJ (vert.) FD (horiz.) FD (vert.) JD LD /Dimensions Extended Circuit P2 Panels Main Breaker Wire Bending Extended Circuits (more than 54 1" module branch poles) Panel Amps Breaker Frames C D 100 BL BQD NGB, HGB, LGB ED (horiz.) ED (vert.) QJ (horiz.) QJ (vert.) FD (horiz.) FD (vert.) JD LD (54p max) N/A N/A Main Lug Connectors Standard Circuits (up to 54 1" module branch poles) Panel Amps Standard Connectors C D (1) #14-2/ (1) # AWG MCM (1) #4 AWG - 00 MCM or (2) # MCM 00 (2) #4 AWG MCM Main Lug Connectors Extended Circuits (more than 54 1" module branch poles) Panel Amps Standard Connectors C D (1) #14-2/ (1) # AWG MCM (1) #4 AWG - 00 MCM or (2) # MCM 00 (2) #4 AWG MCM Branch Breaker Side Gutters Inches (mm) Reference Letter Panel Width 20" (508) A (14) B 5. (130) C (102) D (127) E 4.25 (117) BL, BLH, HBL BL, BLH, HBL A A BLF, BLFH BLF, BLFH B BQD, BQD BQD, BQD B ED, ED4, ED ED, ED4, ED C C HED4, HHED HED4, HHED D QJ2, QJH2, QJ2-H, HQJ2H (Single Mounted) E xgb xgb E Panel Width 20 in. (508 mm) Refer to diagrams at the bottom of page Single branch mounting construction. Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog 11-25

4 11 PANELBOARDS Panelboards Main Breaker a Maximum Interrupting Ref. Ampere Breaker Rating (ka) Catalog Rating Type 240V 480V 00V Number Available Trip Values BL 10 BL 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 90, 100 HBL 5 HB 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 90, 100 BQD 5 14 BQ 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 90, 100 BLH 22 BH 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 90, ED E4 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 90, 100 NGB NB 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 100 HGB G2 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 100 LGB G3 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 100 ED E 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 90, 100 HED H4 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 90, 100 HHED HA 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 90, 100 CED b CE 15, 20, 25, 30, 35, 40, 50, 0, 70, 80, 90, 100 NGB NB 110, HGB G2 110, LGB G3 110, ED E4 ED E HED H4 HHED HA CED b CE QJ2 10 QJ 0, 70, 80, 90, 100, 110,, 150, 175, 200, 225 QJH2 22 QH 0, 70, 80, 90, 100, 110,, 150, 175, 200, 225 QJ2H 42 Q2 0, 70, 80, 90, 100, 110,, 150, 175, 200, 225 HQJ2H 100 Q3 0, 70, 80, 90, 100, 110,, 150, 175, 200, FD FD 70, 80, 90, 100, 110,, 150, 175, 200, 225 FXD FX 70, 80, 90, 100, 110,, 150, 175, 200, 225 HFD HF 70, 80, 90, 100, 110,, 150, 175, 200, 225 HFXD H2 70, 80, 90, 100, 110,, 150, 175, 200, 225 CFD b CF 70, 80, 90, 100, 110,, 150, 175, 200, 225 FD FD 250 FXD FX HFD HF 250 HFXD H2 250 CFD b CF 50 JXD b JX 200, 225, 250, 300, 350, JD b J 200, 225, 250, 300, 350, HJXD b H 200, 225, 250, 300, 350, HJD b H5 200, 225, 250, 300, 350, SJD b SJ 200, 300, SHJD b S2 200, 300, CJD b CJ 200, 300, SCJD b SC 200, 300, LXD b LX 450, 500, 00 LD b L 250, 300, 350,, 450, 500, 00 HLXD b HL 250, 300, 350,, 450, 500, HLD b HO 250, 300, 350,, 450, 500, 00 SLD b SL 300,, 500, 00 SHLD b S 300,, 500, 00 CLD b CL 300,, 500, 00 SCLD C 300,, 500, 00 When an ED4, ED, HED4, QJ2, QJH2, QJ2H, FD, HFD, or FXD frame main breaker, vertically mounted, is required, price as a main breaker panel and add from the table for the main breaker mounting. Vertically Mounted Main Breaker (available in 2-pole or 3-pole) Ampere Rating Breaker Type(s) Unit Space (in.) 100 ED4, ED, HED4 225 QJ2, QJH2, QJ2-H, FXD, FD, HFD Subfeed Breakers (available in 2-pole or 3-pole) Mounting Position When Ampere Maximum Interrupting Rating Breaker Used as Subfeed Breaker Ratings (ka) Symmetrical Type Vertical For Load 240V AC 480V AC 00V AC FD c, FXD Twin HFD c, HFXD Twin JD d, JXD Single HJD d, HJXD Single a Interchangeable trip main breakers are mounted at top of panel only. b Vertically mounted. c Twin mounted subfeed breakers are mounted at the bottom of panelboard only and adds 24" to the panel height. d Subfeed breaker is mounted at bottom of panelboard only. amp subfeed breaker adds 24" to the panel height. (Only for use with MLO) 11-2 Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog

5 Branch Circuit Breakers Max. Amp Rating 100 Bolt-On Breaker Availability Maximum Interrupting Rating (ka) Type Amps 1-Pole 2-Pole 3-Pole 120V AC 120/240V AC 240V AC 277V AC 480V AC 00V AC 250V DC 15 0 u u u 10 BL 70 u u u u u u u u 22 BLH 70 u u u u u 22 HBL u u u u u 5 BL, HID u u BLR (240V) 15 0 u u 10 BLE (GFCI) u u u 10 BLEH u u u 22 BLF (GFCI) u u u u 10 BLHF (GFCI) u u u u 22 BGL b u u BAF u u 10 BAFH u u 22 BQD 15 0 u u u u u u u u u NGB u u u u u u u u HGB u u u u u u u u LGB u u u u u u u u 5 22 ED u u u u u u u ED u u u u u u u HED4 a u u u u u QJ u u QJH u u 22 QJ2H u u 42 Branch Device Limitations In areas where 2008 NEC has not been adopted, some limitations may apply for panels used in systems requiring neutral connections. By application rule ( in all versions of the NEC prior to 2008), lighting and appliance panels are limited to 42 installed circuits. Each over current device pole counts as a circuit. Branch Neutral Connections Wire Range Max. Number of Connections Max. Amp c #14-# 2 5 #14-1/0 28 #-350 kcmil (1) #4-00 kcmil or (2) #-250 kcmil 1 a 1-Pole HED A Rated 5kA 35 through 100A Rated 25kA. b Two pole breaker is one phase and neutral. Three pole is two phase and neutral. c Based on 75 degree copper. 2-pole only (or) two outer poles of 3-pole breaker. NOTE: QJ Breakers are single mounted in unit space and take " of unit space. Limited to (4) per panel max. BL, HBL, BLH and BQD breakers are mounted in common mountings in 3" or () pole increments. ED4, ED, HED4 and HHED breakers are mounted in common mountings in 3" or () pole increments. Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog 11-27

6 11 PANELBOARDS Panelboards Main Lugs Only Maximum Panel Amp Rating Maximum 1-pole Circuits Box Height Inches Catalog Number Catalog Number Catalog Number 3Ø4W 208Y/120V 1Ø3W 120/240V 3Ø4W 480Y/277V 18 2 P2C18MLATS P2A18MLATS P2E18MLATS P2C30MLATS P2A30MLATS P2E30MLATS P2C42MLATS P2A42MLATS P2E42MLATS 54 5 P2C54MLATS P2A54MLATS P2E54MLATS 2 P2CMLATS P2AMLATS P2EMLATS 78 8 P2C78MLATS P2A78MLATS P2E78MLATS P2C90MLATS P2A90MLATS P2E90MLATS P2C18MLTS P2A18MLTS P2E18MLTS P2C30MLTS P2A30MLTS P2E30MLTS P2C42MLTS P2A42MLTS P2E42MLTS 54 5 P2C54MLTS P2A54MLTS P2E54MLTS 2 P2CMLTS P2AMLTS P2EMLTS 78 8 P2C78MLTS P2A78MLTS P2E78MLTS P2C90MLTS P2A90MLTS P2E90MLTS P2C18MLATS P2A18MLATS P2E18MLATS P2C30MLATS P2A30MLATS P2E30MLATS P2C42MLATS P2A42MLATS P2E42MLATS 54 5 P2C54MLATS P2A54MLATS P2E54MLATS 2 P2CMLATS P2AMLATS P2EMLATS 78 8 P2C78MLATS P2A78MLATS P2E78MLATS P2C90MLATS P2A90MLATS P2E90MLATS P2C18ML00ATS P2A18ML00ATS P2E18ML00ATS P2C30ML00ATS P2A30ML00ATS P2E30ML00ATS P2C42ML00ATS P2A42ML00ATS P2E42ML00ATS 54 5 P2C54ML00ATS P2A54ML00ATS P2E54ML00ATS 2 P2CML00ATS P2AML00ATS P2EML00ATS 78 8 P2C78ML00ATS P2A78ML00ATS P2E78ML00ATS P2C90ML00ATS P2A90ML00ATS P2E90ML00ATS Main Circuit Breaker Maximum Panel Amp Rating Maximum 1-pole Circuits Box Height Inches Catalog Number Catalog Number Catalog Number 3Ø4W 208Y/120V 1Ø3W 120/240V 3Ø4W 480Y/277V P2C18BL100ATS P2A18BL100ATS P2E18BL100ATS P2C30BL100ATS P2A30BL100ATS P2E30BL100ATS P2C42BL100ATS P2A42BL100ATS P2E42BL100ATS 18 2 P2C18NBATS P2A18NBATS P2E18NBATS P2C30NBATS P2A30NBATS P2E30NBATS P2C42NBATS P2A42NBATS P2E42NBATS 54 5 P2C54NBATS P2A54NBATS P2E54NBATS 2 P2CNBATS P2ANBATS P2ENBATS 78 8 P2C78NBATS P2A78NBATS P2E78NBATS P2C90NBATS P2A90NBATS P2E90NBATS P2C18QJ225ATS P2A18QJ225ATS P2E18FX225ATS P2C30QJ225ATS P2A30QJ225ATS P2E30FX225ATS P2C42QJ225ATS P2A42QJ225ATS P2E42FX225ATS 54 5 P2C54QJ225ATS P2A54QJ225ATS P2E54FX225ATS 2 P2CQJ225ATS P2AQJ225ATS P2EFX225ATS 78 8 P2C78QJ225ATS P2A78QJ225ATS P2E78FX225ATS P2C90QJ225ATS P2A90QJ225ATS P2E90FX225ATS P2C18FXTS P2A18FXTS P2E18FXTS P2C30FXTS P2A30FXTS P2E30FXTS P2C42FXTS P2A42FXTS P2E42FXTS 54 2 P2C54FXTS P2A54FXTS P2E54FXTS 8 P2CFXTS P2AFXTS P2EFXTS P2C78FXTS P2A78FXTS P2E78FXTS P2C18JXATS P2A18JXATS P2E18JXATS 30 5 P2C30JXATS P2A30JXATS P2E30JXATS 42 2 P2C42JXATS P2A42JXATS P2E42JXATS 54 8 P2C54JXATS P2A54JXATS P2E54JXATS 74 P2CJXATS P2AJXATS P2EJXATS P2C18LX00ATS P2A18LX00ATS P2E18LX00ATS 30 2 P2C30LX00ATS P2A30LX00ATS P2E30LX00ATS 42 8 P2C42LX00ATS P2A42LX00ATS P2E42LX00ATS P2C54LX00ATS P2A54LX00ATS P2E54LX00ATS Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog

7 Type P2 Panelboard Modifications and Additions Enclosures Extra Gutter to Sides or Ends of the Can (Type 1 Only) Description " end gutter 2" side gutter Barrier in gutter (add to extra gutter price min 4" required) 24" wide Hinged trims Piano hinged trims Door-in-door trims Screw to the box trims Trim mounted devices See page Pilot lights Toggle switches Push buttons Painted boxes See page Custom colors See painted boxes Increase gauge trims and boxes See page Stainless steel trims and boxes, Type See page Meters (Contact sales for pricing and application engineering for space requirements) Panel Skirts See page Special Locks TEY TEU1 Cat 0 LL803 LL80 Yale 47 (NYC) National C413A Best Lock 7-pin tumbler Southco 1/4 Fastener Corbin 1001 FAB7 Panel Bus Modifications Catalog Number Addition Amperes Ratings Main Bus A A 00A 750 A/SI AL. B B B B Copper (tin pltd.) F F F F Copper (silver E E E E pltd.) 1000 A/SI Copper G G G G (tin pltd.) 1000 A/SI Copper (silver pltd.) H H H H a Accessories on 1" pole breakers (BL, BQD, ED) will take unit space. Subfeed, Feed-Thru and Split Bus (for 2-pole or 3-pole) Ampere Rating Contactor Mains or Submain* See Page Asco 920 through 225 amps adds 12" unit space as main, 15" unit space as submain External with manufacture supplied enclosure Siemens LEN through 30 amps - adds " as main; 18" for up to 100A submain and 21" for 200A. 7.75" depth cans for up to 100A and 10" depth cans for 200A. *Call plant for correct can size. Branch and Main Breaker Accessories See breaker section of this catalog. Handle blocks Handle locks Aux. Contacts 1 UVR a Increase Capacity Neutral up to 200% (N/A on Feed Thru Lugs & Subfeed Lugs) Main Bus Amps Connector Cu/Al Wire Range Unit Space (inches) Subfeed (Double) Lugs for Main Lug Panelboards Only 100/ (2) #12 AWG-2/0 kcmil 225/250 (2) # AWG-350 kcmil (custom) (4) 250 kcmil (custom) (2) 00 kcmil Feed-Thru Lugs Cannot Be Used in Conjunction with TVSS or Subfeed Breakers (200% Neutral not available) 100/ (1) #12 AWG-2/0 kcmil 225/250 (1) # AWG-350 kcmil (2) 250 kcmil (1) 00 kcmil 9 00 (2) kcmil 12 Split Bus (1 per interior) Requires feed thru lugs also to feed sub panel section and for space requirements. 100/ (1) #12 AWG-2/0 kcmil 225/250 (1) # AWG-350 kcmil (2) 250 kcmil (1) 00 kcmil 00 (2) kcmil See page for unit space adders and compatibility with other options. (Devices mounted and wired to the trim should also have hinged trim specified) Copper MLO Only Main Bus Amps Service Entrance Label are factory labeled suitable for use as service entrance equipment when NEC requirements are met. A panelboard cannot have more than six main disconnects, unless it is a lighting and appliance branch panelboard. Lighting and appliance branch panelboards are limited to two main disconnects. Grounding of Panelboards Bus mounted SPD See Section 10 Ground Bars except for brazed to box are shipped with the panel interior factory mounted. Non-Insulated Equipment Ground Bar Copper Non-Insulated Ground Bar Al Insulated Equipment Ground Bar Cu Insulated Equipment Ground Bar Ground Bar Brazed to Box (Not recommended for painted or NEMA 3R enclosures) Shunt Trip on Main or Branch BL, BLH, HBL, xgb, ED4, HED4, HED, HHED uses 1" unit space for shunt trip. All others may be used on mains or subfeeds. See breaker section for list price adders. Time Clocks Time clocks may be mounted in a 23" enclosure to be cable connected to the panel. Sangamo, Tork or Paragon time clock can be supplied and mounted in panelboard cabinet. Adds 12" to panel height. Mounts in Sub-area. Description Time Clock (1 or 2-pole, single or double throw contacts; 3-pole, single throw) 277V maximum with plain dial Astronomical dial An omitting device Reserve power or carryover Space and mounting provisions only Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog 11-29

8 11 PANELBOARDS Panelboards Type P2 Panelboard Standard Modifications and Additions Box Size Additions for Optional Features Main Lugs Main Breakers A A 00A A A A 225A 225A 225A A A 00A 00A Options JD CJD LD CLD BL, BQD, ED, xgb CED ED QJ QJ FD FD CFD *Min. Box Size 2" 32" 38" 38" 2" 32" 32" 32" 38" 38" 44" 50" 50" 2" 5" 2" 200% Neutral 0 0 (all) (all) N/A 0 N/A (lug type) Std. Lugs (100% Neut. PNL) CU Lugs (100% 0 N/A N/A 0 N/A 0 N/A Neut. PNL) Comp Lugs N/A N/A 0 N/A 0 N/A (100% Neut. PNL) Feed-thru Standard Lugs N/A N/A Feed-thru Cu Lugs 12 N/A N/A N/A N/A N/A N/A N/A Feed-thru Comp Lugs N/A N/A N/A N/A N/A N/A N/A Subfeed Standard Lugs 0 N/A N/A Split Bus N/A N/A (1) FD Subfeed N/A N/A N/A N/A N/A N/A (Horizontal Mtg.) (2) FD Subfeed N/A N/A N/A N/A N/A N/A N/A N/A N/A (Vertical Mtg.) SPD Split bus is paired with feed-thru lugs by default. Feed-thru lugs are to feed the section after the split. NOTE: N/A = OPTION NOT AVAILABLE *Min. Box Size, corresponding to 9" of Unit Space. Compression Lugs Amp Breaker Compression Box Height Style Rating Type Connectors Addition N/A (1)# kcmil Al/Cu 250 N/A (1)# kcmil Al/Cu MLO (1) - 00 kcmil Cu or N/A (2)# kcmil Al/Cu 00 N/A (2)# kcmil Cu or Cu/Al or - 00 kcmil Al/Cu Main Breaker 100 Alternate Lugs Amp Style Rating ED4, ED, HED4 HHED, CED (1)#14-2/0 AWG Cu or Al Box must go to 24" wide on CED breaker only Add " to box height for NØ 225 QJ2, QJH2, QJ2H (1)# AWG kcmil Cu or Al Box must go to 24" wide 250 FXD, HFD, CFD (1)# AWG kcmil Cu or Al Box must go to 24" wide for all breakers Requires an additional.0" box height JD, JXD, HJD, CJD, SJD, SHJD, (2)#1/0 AWG kcmil Cu or Al 9 SCJD 00 LD, LXD, HLD, CJD, SLD, SHLD, SCLD (2)#2/0 AWG kcmil Cu or Al Breaker Type MLO N/A Main Breaker JD, JXD, HJD, CJD, SJD, SHJD, SCJD Standard AL Connectors (1) kcmil or (2)#3/0 AWG kcmil Cu or Al (1)#4/0 AWG kcmil Cu or Al Box Height Addition Not availabe for feed thru lug Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog

9 Type P2 Panelboard Connector Modifications Enclosure Modifications Description 20" Panel Width NEMA 3R enclosures NEMA 3R/12 enclosures Gasket between trim and box (Type 1) 24" Panel Width NEMA 3R enclosures NEMA 3R/12 enclosures Gasket between trim and box (Type 1) NEMA-4 Water Tight, Dust Tight, Steel Enclosure (Actual NEMA-4 enclosure is larger than standard Type 1 enclosure. See chart below for reference to approximate actual size.) Standard Box Height (in inches) Actual NEMA 4 Enclosure Size H W D NOTE: Larger NEMA 4 enclosures are not available. NEMA-4X Water Tight, Dust Tight and Corrosion Resistant (consult plant for actual enclosure size) Catalog Number Enclosure Stainless Steel Size (inches) (304SS is standard) Enclosure Fiberglass Size (inches) H W D H D W B4X B4X B4X B4X B4X B4X B4X B4X B4X NOTE: 31SS is available as an option - must be specified. Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog 11-31

10 11 PANELBOARDS Panelboards Type P2 Panelboard Kits and Accessories Standard Enclosures Box Height Inches Catalog Number Type 1 Standard Trim Box Surface Flush Type 3R Type 3R/12 2 B2 S2B F2B NR2 WP2 32 B32 S32B F32B NR32 WP32 38 B38 S38B F38B NR38 WP38 44 B44 S44B F44B NR44 WP44 50 B50 S50B F50B NR50 WP50 5 B5 S5B F5B NR5 WP5 2 B2 S2B F2B NR2 WP2 8 B8 S8B F8B NR8 WP8 74 B74 S74B F74B NR74 WP74 Options For Type 1 Trims Items must be ordered as manual line item on Spartanburg Hinged trim Replace B suffix with H Door-in-door Replace B suffix with D Screw to Box - Replace "B" suffix with "C" Metal card holder - Add "M" suffix on all trims Option For 24" Wide Enclosures with Equal Gutter on Both Sides (Excludes NEMA 3R) 24" wide with equal gutter on both sides - Add 24 as prefix Breaker Kits and Accessories Kit Number Description Contents BBKB32 BL/BQD -pole 3" branch breaker kit Kit contains top barrier, (3) A/C connectors, (1) B connector, hardware BBKED32 ED -pole 3" branch breaker kit Kit contains breaker support, inter-phase barriers, (3) A/C connectors, (1) B connector, hardware BBKNB32 xgb -pole 3" branch breaker kit Kit contains top barrier, (3) A/C connectors, (1) B connector, hardware BBKQ1 QJ branch breaker kit for 2 and 3-pole single mount Kit to contain all connectors and cover plates necessary to mount both 2 and 3-pole breakers DFK1 BL, BQD, ED deadfront kit for 1" pole breakers Center strips 3", ", 9", 15", 21" plus mounting hardware DFFP3 Deadfront filler 3" 3" empty space filler and hardware DFFP Deadfront filler " " empty space filler and hardware BNK2 Branch neutral (P2) Three tier lug with mounting hardware to increase neutral capacity P2BK1 P2 max. Bonding Kit Bonding strap and hardware P2BK2 P2 A max. Bonding Kit Bonding strap and hardware P2BK3 P2 00A max. Bonding Kit Bonding strap and hardware Type P1, P2, and P3 Panelboards Miscellaneous Parts and Accessories Catalog Number Description Catalog Number Description EGK Al Ground Bus 44 Connections NBK Number Strips 8-18 P2BK1 P2 Bonding Kit NBK7 Number Strips P2BK2 P2 A Bonding Kit NBK8 Number Strips P2BK3 P2 00A Bonding Kit ECGK Cu Ground Bus 44 Connections IMK1 Interior Adjusting Kit IGK Insulated Al Ground Bus Directory Card Holder ICGK Insulated Cu Ground Bus Directory Card EWK1 End Wall Kit with Knockouts (20" W x 5.75" DP) NEMA Instruction Book EWK2 End Wall Kit with Knockouts (24" W x 7.75" DP) NBK3 Number Strips 1-42 DFFP1 1" Filler Plate (suitable for replacing QF3 in P1 thru P5 Panelboards and Switchboards) NBK4 Number Strips EBF1 NEB/HEB Filler Plate NBK5 Number Strips Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog

11 Dimensions Type 1 Box Box is symmetrical Type 3R and 3R/12 Box a Dimensions are interior of the box. Add 5/8" to width for absolute dimension. Add 1/8" to height for absolute dimension. Dimensions shown in inches and millimeters [ ]. Siemens Industry, Inc. SPEEDFAX 2011 Product Catalog 11-33