INSTALLATION MANUAL. SAILOR 5080 AC Power Supply

Size: px

Start display at page:

Download "INSTALLATION MANUAL. SAILOR 5080 AC Power Supply"

Ashlynn McLaughlin
7 years ago
Views:

1 INSTALLATION MANUAL SAILOR 5080 AC Power Supply

3 Contents Introduction... 3 General description... 3 Technical data... 3 Installation... 4 Outline and dimension... 4 Installation wiring... 5 Block diagram switch mode Power Supply Unit... 6 AC supply voltage setting... 7 AC Alarm interface... 8 Schematic diagram... 9 Power Supply Unit... 9 AC Alarm Interface Internal connection Disclaimer Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information purposes only, is subject to change without notice, may contain errors or inaccuracies, and represents no commitment whatsoever by Thrane & Thrane. This agreement is governed by the laws of Denmark. Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on this information should satisfy himself/herself as to the most current version. Providers with access to Thrane & Thrane s Extranet may obtain current copies of manuals at: extranet.thrane.com. Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, in whole or in part, of this manual from any other source

.. 11 Disclaimer Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane.

4 2 0748

5 Introduction General description The 5080 AC Power Supply is designed as a stand alone AC Power Supply, with provision for automatic switch over to backup DC supply/battery. The AC Power Supply is designed with three fused and fully separated output lines to ensure independent supply for connected equipment. Additionally a galvanically isolated AC alarm output is provided. Technical data AC input voltages: 110, 120, 220/230, 240V AC +/- 10% AC input frequency: 50/60 Hz +/- 6% DC output voltage: DC output current: 28V 58 A max. AC Mains Alarm output: Make/break relay contacts 0.5 A 32V. Alarm in case of AC supply failure. Protection: The AC Power Supply is current limited and protected against polarity reversal, short circuit, overvoltage and overtemperature. Operating temperature: - 20 to + 55 C. Dimensions: Weight: H: 638 mm, D: 126 mm, W: 440 mm. Approx kg. Compass safe distance: Standard: 4.0 m. Steering: 2.5 m

Additionally a galvanically isolated AC alarm output is provided.

6 Installation Outline and dimension x ø ) 1) 3) 2) Note: 1) Space for airflow: min. 200 mm. 2) Space for cable and airflow: min. 25 mm. 3) Space for service access: min 1000 mm. All dimensions are in mm. TT Weight: 15.5 kg

7 Installation wiring AC Alarm interface L N AC in A 63A 10A 10A Backup DCout supply input MF/HF Tx Spare out Spare out TT

8 Block diagram switch mode Power Supply Unit

9 AC supply voltage setting Before connecting the AC Power Supply to the AC mains, be sure that the voltage selector switch is set to the correct voltage and that the fuse rating corresponds to the setting used. The voltage selector switch is located on the AC Power Supply assembly under the front cover. The selected voltage is indicated by an arrow in the outer ring (refer to next page). The equipment is normally dispatched with the selector set to 220V. To select a different voltage insert a screwdriver in the slot and turn the switch to the correct setting. Note: As two SMPS units are operated in parallel input voltage selection must be done on both units. Setting Voltage range V V Caution: Incorrect setting of the mains voltage selector may damage the AC Power Supply Assemblies The AC mains fuse holder is an integral part of the AC terminal block which is located to the left under the front cover. The fuse is accessed by pulling out the black handle. The correct rating for each voltage setting is as follows Setting Fuse rating A Slow A Slow Fuses are cartridge type measuring 5 x 20 mm. The AC supply leads are connected as indicated to the terminal block. Screened power L N Live Neutral Protective earth supply cable may be used as required by some administrations. The cable is fastened and the screen connected by a cable clamp on the main chassis below the terminal block. Recommended cable type: 3 x 1.5 mm

The equipment is normally dispatched with the selector set to 220V. To select a different voltage insert a screwdriver in the slot and turn the switch to the correct setting.

10 AC Alarm interface The AC Alarm Interface is located to the right under the front cover. It contains an terminal strip marked AC ALR 0 and AC ALR 1. A cable for a alarm device is to be connected as indicated in the table below. Terminal Designation Description 1 Not connected 2 AC ALR 0 3 AC ALR 1 Galvanically isolated AC alarm output. Relay contacts, max. 0.5 A 32V. Alarm condition: AC supply missing (terminals 2 and 3 are closed). 4 Not connected

A cable for a alarm device is to be connected as indicated in the table below.

11 Schematic diagram Power Supply Unit 9

12 AC Alarm Interface 10

13 Internal connection 24 core charger option cable AC SMPS Stabilized current limited and auto switch over AC alarm interface Fuse terminal 24 core charger option cable Alarm relay out AC SMPS Stabilized current limited and auto switch over Battery input filter Output filter Fuse terminal A 63A 10A 10A Backup DCsupply input DC out DC out DC out AC in TT

62-125797 Stabilized current limited and auto switch over Battery input filter 62-126363 Output filter

16 TT THR-A Issue: 0748 Thrane & Thrane A/S

Modular I/O System Analog and Digital Interface Modules

OPERATING INSTRUCTIONS Modular I/O System Analog and Digital Interface Modules Installation Operation Maintenance Document Information Document ID Title: Operating Instructions Modular I/O System Part