C9 HD Video Conference Terminal

Transcription

1 C9 HD Video Conference Terminal Quick Installation Guide Copyright Notice All contents of this manual, whose copyright belongs to our Corporation. Cannot be cloned, copied or translated without the permission of the company. Product specifications and information which were referred to in this document are for reference only, and the content will be updated at any time without prior notice

2 Packing list When you unpack, check that all the supplied accessories are included: C9 Integrated terminal, complete audio and video coding and decoding, providing high quality audio and video communication Power adapter, power supply connecting wire, power supply for terminal system Remote control, configuration terminals, and control the camera operation meeting A microphone interface, for acquiring an audio signal venue Audio cable, XLR to 3.5mm interface cable Quick Installation Guide, Quick Start, CD-ROM Product Description C9 is a compact, powerful HD video conferencing endpoints with embedded system design, support 1080P HD codec and H.323, SIP protocol. System with integrate design, convenient installation, connect the network cable can be plugged in for communication, voice, image information pass each complete document sharing, and other meeting functions, thus saving time and meeting expenses, improve efficiency, interactive video conferencing for the enterprise and all-round-like face to face communication exchange to facilitate the creation of convenient.

3 Features: Integrated design, camera + terminal integrated into a single device, the application is simple and convenient. Supports Wi-Fi (optional), support external microphone, compact, easy to install and deploy. Integrated camera uses 72.5 of high-quality ultra-wide-angle lens, optical zoom up to 12 times, and 32 times digital zoom support (optional). 1080P Full HD built-in camera, up to 1080p p5 or 2-way 720p30 activity stream, video 2 into two. Network adaptability, FEC anti-loss: 20% loss. RESTful API + Android-based operating environment that supports custom user interface with third-party application development and integration, the development of applications that can be deployed inside or outside the terminal. Full open SDK, provides powerful media processing engine, support the development of protocols and third-party applications, easy customization needs of customers secondary development. Appearance Front Back

4 No. Name Function Interface 1 MIC Connect a microphone to the microphone audio input interface terminal for receiving sound. 2 AUDIO IN 3.5mm audio input interface, used to connect computers, mobile phones and other audio input sources, receiving sound. 3 AUDIO OUT 3.5mm audio output interface, audio cables, connects the speakers to the AUDIO OUT terminal Audio output interface, the output sound. 4 USB1 For external USB device: U disk upgrade, then mouse, keyboard control. 5 USB2 For external USB device: U disk upgrade, then mouse, keyboard control 6 HDMI OUT1 Using an HDMI cable, high-definition TV HDMI OUT1 terminal is connected to the output interface. With audio output 7 HDMI OUT2 Using an HDMI cable to connect to high-definition TV output interface HDMI OUT2 terminal. 8 DVI IN Connecting auxiliary video input device (VGA video source, such as a computer) Using a DVI cable, connect the computer to a DVI IN input interface, press the remote Control button, you can send a second video source to the participant's endpoint. 9 NET With a network cable to connect LAN port terminal, the terminal network.

5 10 DC+12V Connect the power adapter to provide a 12V supply terminal. Parameter index Category Item Details Electrical Characteristics Environmental requirements Physical Characteristics Operating Voltage Power Consumption Working State Temperature Relative Humidity Ambient Noise Minimum Illumination Recommended illumination Non-Working State temperature Relative Humidity Size Net Weight 100V AC~240V AC,50Hz~60Hz;12VDC Maximum power consumption: 24W 0 ~40 0%~80% Less than 46dBA SPL 0.5lux More then300lux -40 ~70 0%~95% 239.4mm(Length)x148.4mm(Width)x157mm(Height) 1.7kg Installation Terminal equipment can be placed directly on the desktop, fixed to the TV or hang on the wall. As shown in the schematic fixed television sets and wall mounting. 1. Flat-panel TV mounted on the schematic

6 组 合 支 架 Combination Bracket Attached to TV 2. Mounted on the wall schematic Explanation 1. If the terminal is placed directly on the desktop, to maintain stable desktop note-slip; 2. If the terminal is placed on a rack, according to the thickness of the TV, using the screws on the frame; 3. Adjust toward the terminal, to avoid being a bright light source (such as a window). Participants recommended that the terminal is on.

7 Connection cable Before connecting the cables, you need to understand the back interface C9 terminals, cable connection as shown includes an optional configuration for reference only, please according to the actual needs of the connection cable. This is as follows: Input the master video: Use the built-in camera. Input the second video image: using a DVI cable, connect your computer to the DVI IN C9 input interface. Input sound: 3.5mm microphone using the supplied adapter cable to connect the microphone to C9 interface supporting the MIC jack. Enter Players Sound: Use 3.5mm audio cable, connect the player to the LINE IN C9 interface.

8 Main video output: HDMI cable connection HDMI OUT1 C9 of the interface to display HDMI input devices interface. Sound output: Use the HDMI cable to connect the HDMI HDMI input connector C9 OUT1 to a display device, or to with 3.5mm audio cable C9 of LINE OUT connectors to the speaker. output of the second video image: HDMI cable, connect the HDMI OUT2 C9 HDMI interfaces to display device Input interface. connect to the network: using the network cable to connect LAN port terminal, the terminal network. Connect the power supply: Connect the DC + 12V C9 interfaces to the power adapter, use the included power cord to connect the power supply Adapter to an electrical outlet. Turn on the power Supporting all devices connected to C9 used, and then connect the power. Note: terminal of the power in the open state, to prevent the power cord from the terminal and cause an outage. Turn off the terminal, then turn off the external power supply (eg power socket), and finally unplug the power cord. Follow asked to inspect the power cord, the power adapter is properly and reliably connected to the device: Make sure the AC supply voltage range between 100V ~ 240V, frequency of 50Hz or 60Hz. FireWire (L), neutral (N) and define the sequence and the corresponding voltage differential protective earth (PE) must comply with international standards,and protective earth grounded. As to HDMI OUT1 output interface, according to the figure after connecting cables, power supply adapter, press the power button (green light), start-up screen to display the main menu (takes about 120 seconds). When turned on, the indicator C9 terminal described in the following table. LED status Power light green long bright C9 terminal state Description Normal operation

9 Long bright orange power indicator Power light is off IR receiver flashes green Disconnect the power is turned off but Power has been disconnected Infrared remote control signal is received Basic Information Set Language 1. In the main interface, select the "Settings" or Settings, enter the setting interface, and then select the "language" or enter the language setting interface Language. 2. Select Back after "English" or Chinese. Set the date and time 1. In the main interface, select "Settings" to enter the setup interface, and then select "Network" to enter the network settings screen. 2. Move to the left of the interface, select the "Date and Time", configure the time parameters.

10 Parameter Parameter Description Select time zone Time Server Auto Sync Select 24-hour format Select date format Back button Set time zone area Set NTP Time Server Setting whether to automatically synchronize time Set whether to enable the 24-hour format Display year, month, day, hour, minute, second Save the configuration information, go to the Network Interface Set the network 1. In the main interface, select "Settings" to enter the setup interface, and then select "Network" to enter the network settings interface. 2. Select "Ethernet configuration."

11 Parameter Network Type IP address Subnet Mask Gateway Address DNS server address Save button Discard button Parameter Description Manual settings: IP address assigned by the network administrator to the terminal, you need to enter IP address of the network connection Subnet mask, network connection Gateway address of the network connection DNS network connection Save the network settings, network settings interface returns Do not save the network settings, network settings interface returns Set the terminal name 1. In the main interface, select "Settings" to enter the setup interface, then select "Account" to enter account setup interface. 2. Select the "General" Configuration "terminal name", select "Save."

12 Configuring H.323 account (optional) Setting terminal H323ID and number, specify GK address, so that the terminal is registered to GK, enabling conference calls by number or other terminals. 1. In the main interface, select "Settings" to enter the setup interface, then select "Account", enter the account settings interface. 2. Select "H.323 Account", press the Enter key, the display settings.

13 Parameter Parameter Description Enable GK GK server address Registered name Terminal number password Save button Enable GK is open, the terminal can register GK; otherwise, the terminal will not register or log off from GK GK's IP address or domain name Name or alias terminal registered on GK E.164 number or alias terminal (optional) GK registration password server(optional) Save the settings, return to the Settings screen Explanation 1, if GK is enabled, register with the GK after the terminal starts. After the terminal successfully registered, you can initiate a call by the distal end of the number will be. 2, if you do not enable GK, GK to the terminal server is not registered, the call can only be initiated via the IP address. Configuring SIP account (optional) SIP configuration parameters, set terminal SIP address, registration number through, with the distal end of the exchange. 1. In the main interface, select "Settings" to enter the setup interface, then select "Account", enter the account settings interface. 2. Select "SIP Account"; press the Enter key, the display settings.

14 Parameter Parameter Description Enable SIP SIP registration server address SIP proxy server address End user name Authentication username Password authentication Certified Domain Save button Enable SIP to open, the terminal can register SIP server; otherwise, the terminal will not be registered or canceled from the SIP server SIP server's IP address or domain name SIP proxy server IP address or domain name (optional) End user name (number) or SIP URI The account authentication user name (optional) The account authentication password (optional) The account authentication domain (optional) Save the settings, return to the Settings screen