Pre-Apprenticeship Training Apprentice Training Post-Trade Training Short Refresher Courses

Transcription

1 The College of Electrical Training (CET) is the major private training provider for the Western Australian electrical & telecommunications industries. Course Delivery Profile Pre-Apprenticeship Training Apprentice Training Post-Trade Training Short Refresher Courses Joondalup Campus 20 Injune Way, Joondalup WA 6027 PO Box4, Joondalup DC WA 6919 Ph (08) Fax (08) Jandakot Campus 5 Avior Avenue, Jandakot WA 6164 PO Box 3857, Success WA 6964 Ph (08) Fax: (08) Our administration team will be happy to assist you. Please call us for enquiries & course bookings. Check out our website RTO No 2394

2 THE CET ELECTRICAL APPRENTICESHIP TRAINING Training Delivery The CET s flexible approach to training delivery means that in addition to training being delivered at the College s modern state of the art facilities, some courses may be completed by correspond- Customised Training We are able to customise courses to suit your training needs. Call our friendly administration team for further information. Cost: Electrical Trade Certificate II in Electrotechnology (Career Start) (Pre Apprenticehsip Electrical UEE 22011) 632 hrs (includes 200 hrs work experience) Full Time Government fees (POA) In addition to essential knowledge and practical skill development the qualification offers applicants with the opportunity of work experience in the electrical trade. Competency plus a selection of Elective Units of Competency relevant to the Electrical Apprenticeship. Cost: Certificate III in Electrotechnology Electrician (Electrical Apprenticeship UEE 30811) Generally, the off-the-job component is completed over three years. Day or Block release Government fees (POA) All units of competency must be successfully completed and the apprentice deemed competent in order to attain a certificate. A WA Unrestricted Electricians Licence is granted upon application and successful completion of the apprenticeship. The essential 66 capabilities identified by ERAC and endorsed by Energy Safety are covered in the qualification. Cost: These training programs have been funded by the Department of Training and Workforce Development Certificate III in Electrical Fitting (Electrical Apprenticeship UEE 33011) Generally, the off-the-job component is completed over three years. Day or Block release Government fees (POA) This qualification provides competencies to manufacture, fit, assemble, erect, operate, test, fault find, alter and repair electrical equipment; and includes electrical wiring work where that work is associated with assembling, maintaining, terminating or altering the wiring between electrical components within plant or machinery. Pre Selection Testing Assessment & Testing We provide aptitude testing for persons wishing to enter an apprenticeship in the electrical trade. Cost: 1.5 hours Subject to demand $66.00 Private bookings only

3 ELECTRICAL LICENCE COURSES POST-TRADE ELECTRICAL CONTRACTORS LICENCE Electrical Contractors Licence Comprising of modules EA103A, EA103B, EA102 & WAE hours Full time or Course Fee: $2, NECA members: $1, Fees include $65.00 of Resource Fees for WAE100, EA102 & EA103B Electrical Contractors Nominees Licence Comprising of modules EA103A & WAE hours Full time or Course Fee: $ NECA members: $ Fees include $20.00 Resource Fee for WAE100 EA103A Operational (Electrical) Legislation Offers the skills necessary for the application of the State Electrical, Safety and Mines Legislation requirements in the completion of an Electrical Installation Course Fee: $ NECA Members: $ hours Full time or Estimating, Tendering & Contracting EA104 A practical guide to greater control over the company s financial planning, management and flow. 39 hours Full time or WAE100 Electrical Requirements Mandatory licensing module designed to up-skill electrical based skills in the areas of standard legislation and testing Course Fee: $ NECA members: $ Fees include $20.00 Resource Fee 32 hours Full Time or EA102 Establishing a Contracting Business This program provides the building foundation skills to establish a contracting business 39 hours Full Time or Course Fee: $ NECA members: $ Fees include $25.00 Resource Fee EA103B General Legislative Requirements Provides the knowledge of State and Federal Legislation relevant to WA business operations Course Fee: $ NECA members: $ Fees include $20.00 Resource Fee 20 hours Full time or Course Fee: $ NECA members: $836.00

4 ELECTRICAL LICENCE COURSES POST-TRADE Western Power Contractor Connect Training Scheme Western Power Contractor Connect Training Scheme This course is designed for Western Power accredited Electrical Contractors and authorized Electrical workers undertaking Energising the Installation tasks. Full time Non-Subsidised Fee: $ Subsidised Fee: $ Western Power Service Apparatus Connection Western Power Service Apparatus Connection This course is designed for Western Power accredited Electrical Contractors and authorized Electrical workers to be approved to connect consumers to the Network. Full time Non-Subsidised Fee: $ Subsidised Fee: $ Course in Electrical Trade Licensing This course has primarily been developed to ensure that persons holding an Australian Trade Certificate in the trades of Electrical Mechanics or Electrical Fitting are provided with the skills and knowledge to be issued with a Western Australian Electrician s License. Course Fee: $ hours over a 2 week period Full time Minimum Australian Context Gap Training This course provides Minimum Australian Context Gap training for the UEE30807 Certificate III in Electrotechnology Electrician qualification. 170 hours split over Part A and Part B Full time Course Fee: Part A $ Part B $ Restricted Electrical License (REL) REL Restricted Electrical Licence For persons who regularly need to perform electrical work associated with a primary work function or activity. Modules to be completed as directed by Energy Safety and will be dependent upon the work area category for which the licence is required. MODULE 1 Electrical Principles and Safety 16 hours Course Fee: $ Subsidised Fee: $ MODULE 2 Disconnect & Reconnect to 1000V 24 hours Course Fee: $ Subsidised Fee: $ Certificate IV in Electrical- Instrumentation UEE40411 Certificate IV in Electrical - Instrumentation This course is designed to provide the Electrical Tradesperson and final year Electrical Apprentice with training in the functionality, operation, calibration and fault finding of basic Industrial Instrumentation. The course provides underpinning knowledge of Instrumentation theory, calibration and processes through a webbased training program which is self-paced and supported administratively and technically by the College. The knowledge obtained through the online tuition is then applied in simulated workplace training units within the College in areas such as pressure, level, temperature, flow, transducers and application to analytical instruments. This can be undertaken once the web- Based programs are completed. Competency can be achieved through repeated undertaking of practical projects at the College or through workplace activities. Students should ideally have home broadband internet access. This is a self-paced course with a large percentage of the theory being delivered online at the students pace (it should be noted that online training must be fully completed within 12 months). Once the online component is completed the student can undertake the practical sessions and undergo assessment. Classes in the practical component will typically be run each month. Non-Subsidised Fee: $ Subsidised Fee: Not Available

5 SHORT COURSES POST-TRADE Programmable Logic Controllers Skill Set Course in Programmable Logic Controllers Skills Set - UEENEEI150A & UEENEEI151A UEENEEI150A covers development, installation and testing of programs for Programmable Logic Controllers (PLC's) for systems requiring extended control functions. Duration/ Low Voltage Switchboard Rescue The course provides an introduction to basic electrical safety and life support. It examines the principles of working safely in confined spaces, hazard identification, effects of electric shock, first aid and resuscitation for persons suffering from electrocution and rescue techniques using a Low Voltage Switchboard Rescue Kit. 2 evening per week for 5 weeks UEENEEI151A covers development and testing of programs for industrial systems requiring advance control functions using structured logic design techniques and the application of high level instructions. Duration/ 2 evening per week for 6 weeks NECA Subsidised Fee: $ Subsidised Fee: $ Non-Subsidised Fee: $ Low Voltage Switchboard Rescue Subsidised Fee: $ Non-Subsidised Fee: $ High Voltage Switching Systems Operations Course High Voltage Switching Systems Provides the knowledge needed for entry to HVS industry. Designed for persons requiring an understanding of HVS or who operate high voltage equipment. Industry recognised training using Brown Boveri equipment. 5 days Subsidised Fee: $ Non-Subsidised Fee: $ Certificate IV in Hazardous Areas Electrical UEE42611 Certificate IV in Hazardous Areas-Electrical The course provides; competencies to supervise, select, install, commission, maintain and test explosion-protected equipment and systems; for control and monitoring of plant and processes. It also contains Skill Sets in working with explosion protection techniques and how they apply to pressurisation; and gas and dust atmospheres. 80 hours 2 weeks full-time with the option of splitting the 2 weeks within a period of 3 months Non-Subsidised Fee: $ Subsidised Fee: Not Available

6 SHORT COURSES Certificate IV in Electrical- Photovoltaic Systems UEE42010 Certificate IV in Electrical-Photovoltaic Systems This nationally recognised qualification provides Electricians with the competencies to install, set up, test, fault find and repair Photo-voltaic Systems in domestic and commercial premises. It contains Units of Competency endorsed by the Clean Energy Council and information regarding the use and application of Interval Metering. 5 days plus 1 evening Non-Subsidised Fee: $3, Work Safely in the Construction Industry CPCCOHSI001A This course is designed to raise safety awareness amongst employers and employees engaged in building and construction work in Australia. UEESS00101 Sustainable - Designer, Installer of Grid Connected UEESS00101 Sustainable - Designer, Installer of Grid Connected Photovoltaic Systems Skill Set This Skill Set provides licensed electricians with the training to design, install, set up, test, fault find, repair and maintain grid connected photovoltaic systems and associated equipment. 5 days & 1 evening1 Non-Subsidised Fee: $1, Work Safely in the 4 hours On demand Non-Subsidised Fee: $99.00 NECA Member Fee: $60.00 EcoSmart Electricians Course Certificate II in Split Air Conditioning and Heat Pump Systems Certificate II in Split Air Conditioning and Heat Pump Systems This course covers the installation, commissioning and de-commissioning of single head, split air conditioning and heat pumps systems to a prescribed routine where the maximum plant capacity for each system does not exceed 18 kwr including wall hung, floor and ceiling suspended, cassette and ducted fan coil split systems and water heating heat pump systems. Face to face 10 days Non-Subsidised Fee: $ Subsidised Fee: $ Loop Impedance Testing This course provides information and training in current loop impedance testing procedures and a skills update in the use of testing equipment EcoSmart Electricians Course This is a new innovative training program developed by NECA which will comprise training for electricians and electrical engineers that will equip them to deal with the rapidly growing demand by consumers for improved energy efficiency. 3 days on-site training available Fee: $ Subsidised Fee: $ NECA Members $ (if entitled to CTF Subsidy) Loop Impedance Testing 4 hours or after hours Subsidised Fee: $55.00 Non-Subsidised Fee: $96.00

7 SHORT COURSES Senior First Aid Training HLTFA301B Apply First Aid Senior First Aid Training The aim of this course is to develop skills and knowledge required to provide a first aid response including life support and management of more complex casualties until the arrival of medical or other assistance. These skills may be applied in a range of situations, including community and workplace settings. Non-Subsidised Fee: $ Subsidised Fee: $ hours : 2 days COURSE AVAILABLE ON DEMAND ONLY Basic Resuscitation Training Basic Resuscitation Training The aim of this course is to develop skills and knowledge required to deliver basic resuscitation, including calling for help and providing basic life support. (Minimum certificate requirement for entry onto any Western Power site). HLTCPR211A Apply CPR Non-Subsidised Fee: $ Subsidised Fee: $ hours : 1/2 day Basic Workplace First Aid Training HLTFA211A Provide Basic Emergency Life Support Prevention of Electrical Incidents Ideally, this course attempts to eliminate electrical incidents through providing knowledge, raising awareness and introducing safe work practices into the electrical workers daily routine. It also provides a genuine means by which an employer of electrical workers can be assured they are meeting their Duty of Care responsibilities. Prevention of Electrical Incidents Non-Subsidised Fee: $ Subsidised Fee: $ Prevention of Electrical Incidents 2 Prevention of Electrical Incidents 2 This course is the second in a series and aims to refresh students on the previous course outcomes and introduce additional areas where potential electrical incidents could occur and training is required. It reinforces the need for the electrical worker to be extra careful when working in certain electrical situations. The training of this course addresses the need to eliminate electrical incidents by providing knowledge, raising awareness and reinforcing the need for safe working practices in the industry. Non-Subsidised Fee: $ Subsidised Fee: $ Basic Workplace First Aid Training The aim of this course is to develop skills and knowledge required to recognise and respond to life threatening emergencies. This includes calling for help, providing basic life support and basic management of common life-threatening conditions in a workplace context. : 1 day Non-Subsidised Fee: $ Subsidised Fee: $45.00 COURSE AVAILABLE ON DEMAND ONLY

8 SHORT COURSES Electrical Cords & Plugs Electrical Cords & Plugs Non-Licenced The Cords & Plugs course provides persons with the training, skills and knowledge required to fit low voltage plug tops and assemble extension leads (up to 1000 volts AC). The course is structured to include both theoretical and practical training. The College s training facilities allow for skills to be practiced in a simulated workplace environment. This course is designed for those persons who need to perform electrical work that is associated with low voltage plugs and cords. or after hours (after hours course subject to demand) Course Fee: $ Understanding Contract Law and Contracts - A Practical Guide - Understanding Contract Law and Contracts This seminar will introduce contractors to some fundamentals of contract law as well as deliver some practical knowledge in regards to drafting contracts, understanding some of the common clauses in contracts typically encountered by contractors, managing risk in contracts, terminating contracts and what to do when a contract is breached. 6 hours On demand Subsidised Fee: $ Non-Subsidised Fee: $ NECA Members Subsidised Fee: $ Non-Subsidised Fee: $ Lighting for Living Lighting for Living This is a new innovative training program developed by NECAVIC which will provide training for electrical contractors in the new energy efficiency lighting requirements for 6 star housing contained within Section J of the Building Code of Australia (BCA). 1 day () or 2 evenings () Course delivery mode is flexible with classes scheduled to meet individual needs Non-Subsidised Fee: $ Subsidised Fee: $ Portable Appliance Testing (PAT) Portable Appliance Testing (PAT) This course provides information regarding the safe and accurate operation of the Portable Appliance Tester (PAT) and testing of RCDs for persons required to operate this type of equipment. Essentially, the course is aimed at persons who have little or no understanding of electrical theory and are required to endorse equipment as safe to use. Non-Subsidised Fee: $ Subsidised Fee: $ Hours /on-site training available Cords & Plugs & Portable Appliance Testing (PAT) Cords & Plugs & Portable Appliance Testing This course provides an introduction to flexible cords and plugs and to the operation of the Portable Appliance Tester (PAT) and the testing of RCDs for persons with little or no understanding of electrical theory. Non-Subsidised Fee: $ Subsidised Fee: $ Hours /on-site training available

9 TELECOMMUNICATION CABLING ACMA Open Cabling Training Requirements UEENEEF102A UEENEEF102A ACMA Open Cabling Training Requirements This skill set provides the training, skills and knowledge recognised by registrars for an Australian Communications Media Authority (ACMA) Open Cabling Registration. 5 days Full time Non-Subsidised Fee: $ Subsidised Fee: $ ACMA Restricted Cabling Registration ACMA Restricted Cabling Registration Course Provides the off-the-job training required to apply for ACMA Restricted Cabling registration. Suitable for persons working as security alarm installers. Course Fee: $ hours Full/Part-time ACMA Open Cabling Registration After Hours ACMA Open Cabling Registration After Hours Course Provides the manual and theoretical skills required by electrical tradespersons seeking ACMA Open Cabling registration. 2 nights a week for 5 weeks Plus 2 Saturdays After hours Course Fee: $ Non-Subsidised Fee: $ ACMA Registration Conversion Course ACMA Registration Conversion Course Delivers Restricted Cablers with the skills to qualify for an upgrade of their ACMA Registration to an open status. 36 hours Course Fee: $ ACMA Restricted Cabling Registration - Existing Operators ACMA Restricted Cabling Registration Course Existing Operators For A grade electricians or experienced security/fire system installers who have 6-12 months telecommunications cabling experience. Offers off the job training to apply for ACMA Restricted Cabling Registration. 2 Full/Part-time Course Fee: $ ACMA Recognised Training Category 5/6/7 and Coaxial Endorsements UEENEEF104A Category 5/6/7 and Coaxial Endorsements This course is an extension of the ACMA Open Cabler Registration training course and provides applicants with the training, skills and knowledge required to correctly install and terminate Category 5/6/7 structured and Coaxial cabling. 2 days Full time Non-NECA Member Course Fee: $ NECA Member Course Fee: $ UEENEEF105A Optical Fibre UEENEEF105A Optical Fibre This module provides the student with the knowledge and skills required to correctly install and terminate fibre optic cable. Course Fee: $ Subsidised Fee: $ hours : 2 days, Part-time: 4 evenings plus one Saturday

10 SKILLS REFRESHER COURSES Senior First Aid Refresher Training Senior First Aid Refresher Training The aim of this course is to refresh and reaccredit skills and knowledge gained in Senior First Aid. A current Senior First Aid text book supplied to the participant for pre-reading to update knowledge. Participants then attend an 8 hour day which concentrates on skills and the more important aspects of theory. A full Senior First Aid theory assessment is then undertaken. : 1 day Subsidised Fee: $45.00 Non-Subsidised Fee: $ Checking and Testing an Electrical Installation Checking and Testing an Electrical Installation Refresher course to update qualified electricians in the current testing procedures, in terms of WA Electrical Requirements and compliance with Australian Standards. Subsidised Fee: $90.00 Non-Subsidised Fee: $300.00