BY: AHF DOCUMENT NO. : L j := 12.2m 1025 kg m Steel density ρs:= 7850 kg m Marine growth thickness tm:= Anti-corr.coat thickness tce:= 4 mm.
|
|
- AHF Faqih
- 8 years ago
- Views:
Transcription
1 PROJECT : 16" CROSSING #2 - PIPE DATA DOCUMENT TITLE: BY: AHF DOCUMENT NO. : DATE: INPUT Outside diameter steel pipe OD:= 16 in Concrete coat thickness tco:= 25 mm Nominal steel wall thickness ts:= 12.7mm Concrete coat density ρcon:= 3043 kg m Pipe joint length L j := 12.2m Sea water density ρsea:= 1025 kg m Steel density ρs:= 7850 kg m Marine growth thickness tm:= 0 mm Anti-corr.coat thickness tce:= 4 mm Marine growth density ρm:= 1200 kg m Anti-corr.coat density ρce:= 1280 kg m Cut back length of field joint CB:= 0.6m Steel loss due to corrosion (assump.) tcorr:= 0.25 mm Field joint (infill) density ρfj:= 1025 kg m Fluid content density ρc:= 1025 kg m Air density ρa:= 1 kg m Density of combined concrete & field joint coat 2. CALCULATION Inside diameter of steel Diameter anti-corr coating Diameter concrete coating Diameter marine growth Total Outside Diameter Bouyancy L j CB CB ρconfj:= ρcon + ρfj ρconfj = m 3 kg L j L j Di:= [ OD 2( ts tcorr) ] Di = 0.38m ODce:= ( OD + 2tce) ODce= 0.41 m ODceco:= ( OD + 2tce+ 2tco) ODceco= 0.46 m ODcecoM:= ( OD + 2tce+ 2tco + 2tM) ODcecoM = 0.46 m ODtotal:= ODcecoM ODtotal = 0.46 m π Fb:= 4 ODtotal)2 ρsea Fb = m kg π Steel area Ast:= ( OD) 2 Di 2 Mass of steel (in air) Mst:= Astρs Mst= m 1 kg 4 π Anti-corr coat area Ace:= ( 4 ODce2 OD 2 ) Mass of anti-corr (in air) Mce:= Ace ρce Mce = 6.6m 1 kg ( ) π Conc coat area Ac:= 4 ODceco2 ODce 2 Mass of conc. (in air) Mc:= Acρcon Mc= m 1 kg ( ) π Mar.growth area Am:= 4 ODcecoM2 ODceco 2 Mass of mar.growth Mm:= AmρM Mm = 0m 1 kg (in air) π Pipe bore area Abore:= ( ) 4 Di2 Mass of fluid content Mcont:= Abore ρc Mcont = m 1 kg in inside pipe Mass of air in inside pipe Mair:= Abore ρa Mair= 0.11m 1 kg MASS IN-AIR Mass of coated pipe (in air, and air in inside pipe) M_in_air:= ( Mst+ Mce + Mc+ Mm) M_in_air = m 1 kg MASS IN-WATER (SUBMERGED) Mass of coated pipe (in water, and air in inside pipe) Mass of coated pipe (in water, and flooded in inside pipe) M_in_water_empty:= ( Mst+ Mce+ Mc+ Mm + Mair) Fb M_in_water_empty= 59.07m 1 kg M_in_water_flooded:= ( Mst+ Mce+ Mc+ Mm + Mcont) Fb M_in_water_flooded = m 1 kg Pipe data-mass.xmcd 1 of 1
A Table of the Most Common Standard Pipe Sizes. Nominal Bore 1/2 inch (DN 15 mm), Outside Diameter 21.34 mm
Standard Pipe Sizes Standard Pipe Sizes Except for specialist applications, commercially available pipe comes in standard sizes. Pipes in a variety of materials - including carbon steel, steel alloys,
More informationHOSE, TUBE, AND PIPE CLAMPS
hose, tube & clamp B/W pages 24/6/08 9:28 AM Page 2 HOSE, TUBE, AND PIPE CLAMPS TABLE OF CONTENTS Introduction 3 Construction 3 Application 3 Mounting 3 Standard Duty Clamps (HRL) Arrangements 4 Dimensions
More informationSeawater corrosion resistant piping systems for large diameters up to 100 / 2.5 metres O.D.
OSNA -10 Copper-Nickel Lined Pipes Seawater corrosion resistant piping systems for large diameters up to 100 / 2.5 metres O.D. KME Germany AG & Co. KG Copper-Nickel Lined Pipes [GB] Member of the KME Group
More informationA World Class Manufacturer of Induction Bends
A World Class Manufacturer of Induction Bends COFELY FABRICOM BENDING A leading position in bending High Flexibility and Close Tolerances As a world leading manufacturer of pipe bends, produced by induction
More informationFlow Assurance & Operability
Flow Assurance & Operability Erosion due to sand production Date Business Name Overview 1. What causes erosion? 2. Sand production and transport 3. Sand management 4. Instrumentation / monitoring of sand
More informationBuoyancy Problem Set
Buoyancy Problem Set 1) A stone weighs 105 lb in air. When submerged in water, it weighs 67.0 lb. Find the volume and specific gravity of the stone. (Specific gravity of an object: ratio object density
More informationGOST 632-80 CASING AND COUPLINGS
GOST 632-80 CASING AND COUPLINGS Casing to this standard shall be seamless, with round and buttress-type threads (OTTM-type casing), with high-seal thread connection (OTTG-type casing) and respective couplings;
More informationBuoyant Force and Archimedes' Principle
Buoyant Force and Archimedes' Principle Introduction: Buoyant forces keep Supertankers from sinking and party balloons floating. An object that is more dense than a liquid will sink in that liquid. If
More informationGALVANIC CATHODIC PROTECTION 1.0 CONTENTS. 1.1 Aluminium Anodes. 1.2 Zinc Anodes. 1.3 Magnesium Anodes SECTION
SECTION 1 GALVANIC CATHODIC PROTECTION 1.0 CONTENTS 1.1 Aluminium Anodes 1.1.1 Aluminium Tank Anodes 1.1.2 Aluminium Hull Anodes 1.1.3 Aluminium Platform / Jetty Anodes 1.2 Zinc Anodes 1.2.1 Zinc Tank
More informationConcrete Pipes. Concrete Pipes
Various Types of Manufactured and Supplied by the Wolfman Company 1. Data Concrete pipes of all types are manufactured at Wolfman according to IS-27 (May 2010). IS 27 is the Israeli Standard that adopted
More informationHomework 9. Problems: 12.31, 12.32, 14.4, 14.21
Homework 9 Problems: 1.31, 1.3, 14.4, 14.1 Problem 1.31 Assume that if the shear stress exceeds about 4 10 N/m steel ruptures. Determine the shearing force necessary (a) to shear a steel bolt 1.00 cm in
More informationHigh Density Polyethylene Liners for Rehabilitation of Corroded Pipelines
High Density Polyethylene Liners for Rehabilitation of Corroded Pipelines Jeff Schell General Manager United Pipeline Middle East, Inc. Introduction HDPE Liners A cost effective and environmentally beneficial
More informationThe surface roughness of the polyurethane lining is 10 times lower than cement-lined pipes.
QUALITY INSIDE When it comes to long life piping for drinking water, sewage, industrial water or gas, there is one name that continues to lead the way - ECOPUR by vonroll. Delivering precision-engineered
More informationTrunk Cables. www.teletronik.com
Trunk Cables www.teletronik.com Brief Introduction Teletronik TC series coaxial cable was developed to meet the increasing demand of tomorrow's broadband networks. TC series cable has the highest reliability
More informationPolyethylene Pressure Pipe
-25 Pipe Systems dvantages Pipe made from polyethylene is a cost-effective solution to a broad range of piping problems in municipal, industrial, marine, mining, and agricultural applications. It has proven
More informationDrop cables. Vorstadt 32 CH, 6304 Zug Switzerland. teletronik@teletronik.com www.teletronik.com
Drop cables Vorstadt 32 CH, 6304 Zug Switzerland AG teletronik@teletronik.com www.teletronik.com Brief Introduction Teletronik RG series coaxial cable was developed to meet the increasing demand of tomorrow's
More informationPipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
More informationAppendix A: Acceptable pipe and fitting materials
Watercare Services Limited Water and Code of Practice Content from the NZS 4404:2010 Land development and subdivision infrastructure has been reproduced for use in the Infrastructure Design s Manual for
More informationHigh Capacity Helical Piles Limited Access Projects
High Capacity Helical Piles Limited Access Projects Tel 403 228-1767 Canada, USA, Russia Brendan ODonoghue 519 830-6113 Presentation Summary 1. Helical piles Background on large diameter shafts and helices
More informationMercury is poured into a U-tube as in Figure (14.18a). The left arm of the tube has crosssectional
Chapter 14 Fluid Mechanics. Solutions of Selected Problems 14.1 Problem 14.18 (In the text book) Mercury is poured into a U-tube as in Figure (14.18a). The left arm of the tube has crosssectional area
More informationInitial Experiments of a Novel Liquid Desiccant Dehumidifier for Industrial and Comfort Air Conditioning Systems
Abstract Initial Experiments of a Novel Liquid Desiccant Dehumidifier for Industrial and Comfort Air Conditioning Systems M. Jaradat, R. Heinzen, U. Jordan, K. Vajen Kassel University (Germany), Institute
More informationPhysics 1114: Unit 6 Homework: Answers
Physics 1114: Unit 6 Homework: Answers Problem set 1 1. A rod 4.2 m long and 0.50 cm 2 in cross-sectional area is stretched 0.20 cm under a tension of 12,000 N. a) The stress is the Force (1.2 10 4 N)
More informationTG 105 ALLOWABLE PIPE SIZE, CLASS AND MATERIALS FOR WATER MAINS TECHNICAL GUIDELINE. Manager Asset Management SOUTH AUSTRALIAN WATER CORPORATION
TG 105 SOUTH AUSTRALIAN WATER CORPORATION TECHNICAL GUIDELINE ALLOWABLE PIPE SIZE, CLASS AND MATERIALS FOR WATER MAINS Issued by: Manager Asset Management Issue Date: SA WATER 2007 This document is copyright
More informationHYDRAULIC PIPING STANDARD HANDBOOK. Revision 1
HYDRAULIC PIPING STANDARD HANDBOOK Revision 1 Preface We aim to fill a gap in technical literature. At this moment there are no hydraulic piping standards available which cover different pressure classes
More informationBEST PRACTICE GUIDELINES FOR CULVERT LINER SELECTION
BEST PRACTICE GUIDELINES FOR CULVERT LINER SELECTION GENERAL Rehabilitation of culverts with pipe liners is one of several methods available for extending the life of an existing culvert. It is often cost
More informationWATER MAIN CONSTRUCTION TECHNIQUES DEPARTMENT OF PUBLIC WORKS WATER & WASTEWATER DIVISION
WATER MAIN CONSTRUCTION TECHNIQUES Overview Water Main - Materials Specifications Installation Future? Water Main Materials Material Types There are various material types used for water mains, these include:
More informationPole Data Sheets (CDN) INFRASTRUCTURE FOR LIFE
Data Sheets (CDN) INFRASTRUCTURE FOR LIFE RS Technologies www.rstandard.com Email Toll Free Phone Fax info@grouprsi.com +1 877 219 8002 +1 403 219 8000 +1 403 219 8001 2421 37th Avenue NE, Suite 400 Calgary,
More informationSolution for Homework #1
Solution for Homework #1 Chapter 2: Multiple Choice Questions (2.5, 2.6, 2.8, 2.11) 2.5 Which of the following bond types are classified as primary bonds (more than one)? (a) covalent bonding, (b) hydrogen
More information2 1/2 Pipe. 40 = height. the gauge pressure inside the vessel from the gauge pressure at the nozzle inlet as shown:
116eering. Engineering. Engineering. Engineering. Engineerin Engineering Information SPECIFYING SPRAY NOZZLES Spray nozzles have three basic functions: meter flow distribute liquid break up a liquid stream
More informationHydrophobe VII., Lisbon
Hydrophobe VII., Lisbon The water repellent treatment of building materials in thermal baths Debrecen, Hungary The geothermal potential in EU János Major University of Debrecen, Faculty of Thermal baths
More informationAccessories for GF and RA machines
Orbital cutting & beveling machines for high-purity process piping www.orbitalum.com Accessories for GF and RA machines A brand of ITW Orbital Cutting & Welding 23 www.orbitalum.com Orbital cutting & beveling
More informationPART 5 : WASTEWATER DRAINAGE
Authorised by : City Waters Unit Manager Page 1 of 15 PART 5 : WASTEWATER DRAINAGE 5.1 INTRODUCTION This Manual sets out the basic design principles for drainage of wastewater. While some construction
More informationCouplings. Drain Couplings Standard Couplings Large Diameter Couplings Adaptor Couplings Flexible Saddles Bushes
Drain Couplings Standard Couplings Large Diameter Couplings Adaptor Couplings Flexible Saddles Bushes Flex-Seal couplings meet a range of UK and international legislation requirements and quality standards
More informationThe conditions below apply to the curves shown on the following pages.
GENERAL INFORMATION STAINLESS STEEL, SILVERLINE, EVERGREEN & GOLDLINE SERIES PERFORMANCE CURVE CONDITIONS The conditions below apply to the curves shown on the following pages. a. The Performance curves
More informationPIPELINE SPAN NON-DESTRUCTIVE INSPECTION REPORT DYNEGY MOSS LANDING POWER PLANT JULY 19, 2011 - REV A OWNER: CLIENT: PREPARED BY:
PIPELINE SPAN NON-DESTRUCTIVE OWNER: TOM BROKAW, SENIOR PLANT ENGINEER DYNEGY, INC. MOSS LANDING POWER PLANT HIGHWAY 1 & DOLAN ROAD MOSS LANDING, CA. 95039 TEL. 831.633.6687 thomas.w.brokaw@dynegy.com
More informationThe soot and scale problems
Dr. Albrecht Kaupp Page 1 The soot and scale problems Issue Soot and scale do not only increase energy consumption but are as well a major cause of tube failure. Learning Objectives Understanding the implications
More informationFLUID MECHANICS. TUTORIAL No.7 FLUID FORCES. When you have completed this tutorial you should be able to. Solve forces due to pressure difference.
FLUID MECHANICS TUTORIAL No.7 FLUID FORCES When you have completed this tutorial you should be able to Solve forces due to pressure difference. Solve problems due to momentum changes. Solve problems involving
More informationSTATE BANK OF INDIA.
Page 1 of 5 B SANITARY, PLUMBING & DRAINAGE STATE BANK OF INDIA. PROPOSED RURAL SELF EMPLOYMENT TRAINING INSTITUTE AT RAIGARH IN C.G. DIRECTOR'S BUNGALOW SCHEDULE OF ITEMS-PLUMBING AND SANITARY WORK 1
More informationRuukki Finnera. The most intelligent roof ever seen.
Ruukki Finnera The most intelligent roof ever seen. Finnera s new and innovative design makes your steel roof not only beautiful but also extremely durable and practical. The revolutionary front-edge folding
More informationKONRAD. Hybrid Fancoil Series
KONRAD Hybrid Fancoil Series Konrad is an innovative radiator which cools you down and warms you up. Indeed, it cools in summer and heats in winter; but it makes it with an incomparable quietness. Thanks
More informationPipe Cutting and Beveling Clamshells
Pipe Cutting and Beveling Clamshells Who We Are One Company, Total Support, Complete Solutions For more than a century, Hydratight has provided world-class bolted joint solutions and continues to set international
More informationMATERIALS AND MECHANICS OF BENDING
HAPTER Reinforced oncrete Design Fifth Edition MATERIALS AND MEHANIS OF BENDING A. J. lark School of Engineering Department of ivil and Environmental Engineering Part I oncrete Design and Analysis b FALL
More informationHYLINER AKS HDPE LINING
HYLINER AKS HDPE LINING FOR CONCRETE PIPE Manufactured from HDPE Available in white and black Sheets up to 3 m width D1.12 HyLiner AKS HDPE Lining for Concrete Pipe October 2013 0800 WE PIPE (93 7473)
More informationTrade Standard of Town Construction in PRC
CJ/T 136-2007 Trade Standard of Town Construction in PRC CJ/T 1 36 2007 Replaces CJ/T 136 2001 Steel pipes of lining plastic for water supply Date of issue: Jan. 17 th, 2007 Date of enforce: Sep. 1 st,
More informationDuctile Iron Pipe Couplings
J-9 Pipe 1 2 Straight and Transition Ductile offer an easy and economical way of joining whether the is of the same nominal and/or type or different at each coupling. couplings will handle most of your
More informationCHAPTER 29 VOLUMES AND SURFACE AREAS OF COMMON SOLIDS
CHAPTER 9 VOLUMES AND SURFACE AREAS OF COMMON EXERCISE 14 Page 9 SOLIDS 1. Change a volume of 1 00 000 cm to cubic metres. 1m = 10 cm or 1cm = 10 6m 6 Hence, 1 00 000 cm = 1 00 000 10 6m = 1. m. Change
More informationCardok Sàrl CP37 CH-1295 Tannay Switzerland Phone: 0041 22 77 66 051 info@cardok.com
CARDOK CARLIFT Fast access to underground garages Fast, Silent, Discreet, Design, High-Tech Installation to replace an access ramp on private property Dimensions: (Built to measure, all dimensions can
More informationNPCA Buoyancy White Paper
NPCA Buoyancy White Paper Section 1- Buoyancy Guide 1.1 Intro Buoyancy is defined as the tendency of a fluid to exert a supporting upward force on a body placed in a fluid (i.e., a liquid or a gas). The
More informationTRIO 330 The framed panel formwork for heights of up to 3.30 m
TRIO 330 The framed panel formwork for heights of up to 3.30 m product range 4.30 3.30 2 ties up to 3.30 m TRIO 330 The framed panel formwork for floor heights up to 3.30 m TRIO 330 is an independent formwork
More informationState of Illinois Department Of Transportation CONSTRUCTION INSPECTOR S CHECKLIST FOR STORM SEWERS
State of Illinois Department Of Transportation CONSTRUCTION INSPECTOR S CHECKLIST FOR STORM SEWERS While its use is not required, this checklist has been prepared to provide the field inspector a summary
More informationVandal-proof keypad series
Model No. LBKP35900 / LBKP35900E (Encryption available) Interface: PS2, USB available. Dimensions: 100mm x 91.5mm No. of keys: 16 keys, high quality stainless steel G.W.: 0.75kg. All languages version
More informationElastoFlake & ElastoTec
ElastoFlake & ElastoTec Relining Group 02 Revolutionally injection casting ElastoFlake, a new material from the Relining Group, is a polymer plastic mass intended for injection casting, which was developed
More informationVOLUME AND SURFACE AREAS OF SOLIDS
VOLUME AND SURFACE AREAS OF SOLIDS Q.1. Find the total surface area and volume of a rectangular solid (cuboid) measuring 1 m by 50 cm by 0.5 m. 50 1 Ans. Length of cuboid l = 1 m, Breadth of cuboid, b
More informationVrtné trubky Drill Pipe
Vrtné trubky Drill Pipe VRTNÉ ROURY - zušlechtěné závity - vysoká kvalita těla roury - svařeno třením - vysoká přímost vrtných tyčí - závity dle STN, API, DIN a GOST - délky dle přání zákazníka Průměr
More informationAluminium foil properties: Applications of aluminium foils and thin gauge strips in thickness below 0,50 mm:
1 ALUMINIUM FOILS AND THIN GAUGE STRIPS The year 2010 has been celebrated as the 100th anniversary of aluminium foil. Ever since the beginning in 1910 the usage of foil has been growing and products developed
More informationThree Methods for Calculating the Buoyant Force Gleue: Physics
Three Methods for Calculating the Buoyant Force Gleue: Physics Name Hr. The Buoyant Force (F b ) is the apparent loss of weight for an object submerged in a fluid. For example if you have an object immersed
More informationHilti, Inc. 5400 South 122 nd East Avenue Tulsa, OK 74146. 1-800-879-8000 www.hilti.com
Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationTECHNICAL NOTE Culvert Sliplining and Lining of Casings with HPPipe
TECHNICAL NOTE Culvert Sliplining and Lining of Casings with HPPipe TN 5.14 February 2010 Introduction It may be at times necessary, in an aging infrastructure, to rehabilitate drainage and sanitary lines
More informationJune 2007 CHAPTER 7 - CULVERTS 7.0 CHAPTER 7 - CULVERTS 7.1 GENERAL
7.0 7.1 GENERAL For the purpose of this manual, culverts are defined as structures that are completely surrounded by soil and located below the surface of the roadway parallel to the general direction
More informationSection 402. STORM SEWERS
402.02 Section 402. STORM SEWERS 402.01. Description. This work consists of constructing storm sewers of the size and class required, including excavation, bedding, and backfill. 402.02. Materials. Provide
More informationWater Volume Calculation in Hydronic Heating & Cooling Systems
Water Volume Calculation in Hydronic Heating & Cooling Systems Preface There are several methods which can be used to calculate the volume of water in a hydronic heating or cooling systems. However, these
More information1x90 TONS TENSIONERS TECHNICAL PROPOSAL. 1 X 90 Tons 30 m/min Tensioners TECHNICAL PROPOSAL JOB 08/059. 0 19/02/2008 Basic proposal PP GM SB
Pagina N.: 1 of 19 1 X 90 Tons 30 m/min Tensioners JOB 08/059 0 19/02/2008 Basic proposal PP GM SB Rev N Date Issue Description Prepared by Checked by Approved by Pagina N.: 2 of 19 TABLE OF CONTENTS:
More informationThis will also provide you with the knowledge to insure long life for your Investment
CONDUIT PIPE DRYING This Presentation will guide you to why systems fail! This will also provide you with the knowledge to insure long life for your Investment Drainable and Dryable System Design Trough
More informationGPD Rubber Press Seals
GPD Rubber Press Seals Leading in in ideas SYSTEM-TECHNIK GPD Rubber Press Seals Design Available with a rubber thickness of 30 mm for sealing against non-pressing water and a rubber thickness of 60 mm
More informationSmart Electromagnetic Flowmeter Open channel Flowmeter Detector
Magne3000 PLUS Smart Electromagnetic Flowmeter Open channel Flowmeter Detector Model NNK150/951 OVERVIE The Magne3000 PLUS Electromagnetic Flowmeter is submersible type of flowmeter mainly used for flow
More informationVapor Corrosion Inhibitors (VCIs) for Storage Tanks Corrosion Controlled Cost Controlled
Vapor Corrosion Inhibitors (VCIs) for Storage Tanks Corrosion Controlled Cost Controlled Presented by Kelly Baker, Zerust Oil & Gas Efim Lyublinski, Monique Posner, Terry Natale, Yefim Vaks, Ronnie Singh
More informationMultistage high-pressure multistage centrifugal pumps
Series description Wilo-Helix V 2 4 6 8 Wilo-Helix V 19-27 7 6 6 Hz - North America 22 2 18 5 16 14 4 12 3 1 V 1 V 19 V 27 8 2 6 1 5 1 15 2 25 3 4 2 35Q[US gpm] H[ft] H[m] Design Vertical multi-stage,
More informationOUTCOME 1 STATIC FLUID SYSTEMS TUTORIAL 1 - HYDROSTATICS
Unit 41: Fluid Mechanics Unit code: T/601/1445 QCF Level: 4 Credit value: 15 OUTCOME 1 STATIC FLUID SYSTEMS TUTORIAL 1 - HYDROSTATICS 1. Be able to determine the behavioural characteristics and parameters
More informationFiber Optic Cable Pipeline Leak Detection Systems for Arctic & Cold Region Applications
Fiber Optic Cable Pipeline Leak Detection Systems for Arctic & Cold Region Applications Prem Thodi, Mike Paulin, Duane DeGeer & Craig Young INTECSEA November 18-19, 2014 Outline Who we are Experience with
More informationPipe Inspection Carbon Steel Trials
Pipe Inspection Carbon Steel Trials Client Innospection Limited Facility Head Office Aberdeen Item Inspected Pipe No 1 Inspection Method SLOFEC Date Commenced 01/01/2009 Date Completed 10/01/2009 Type
More informationReticulation sewers in basements Technical guidelines
Reticulation sewers in basements Technical guidelines Overview What These guidelines explain our technical requirements for laying sewers in building basements. The scope of the guide is restricted to
More informationNEW CONNECTION INDUSTRIAL PRODUCTS NC.10V NC.20V NC.30V. NC. SD.10 NC. SD.20 NC. F.Clamp
Repair and Construction. Complete stainless steel pipe repair clamps to repair cracks, fractures, pin holes, torn sockets or welded tees, broken asbest-cement pipe coupling and more. Available for all
More informationEcophon Focus A. System range. Size, mm. XL 2000x600. XL 1800x600. XL 2400x600 T15 T24 Thickness (THK) Inst. Diagr. 1200x600 1200x1200 1600x600
Ecophon Focus A For applications where a robust suspended ceiling system is required. Ecophon Focus A has an exposed grid system. Each tile is easily demountable. The systems consist of Ecophon Focus A
More informationp atmospheric Statics : Pressure Hydrostatic Pressure: linear change in pressure with depth Measure depth, h, from free surface Pressure Head p gh
IVE1400: n Introduction to Fluid Mechanics Statics : Pressure : Statics r P Sleigh: P..Sleigh@leeds.ac.uk r J Noakes:.J.Noakes@leeds.ac.uk January 008 Module web site: www.efm.leeds.ac.uk/ive/fluidslevel1
More informationOil and Gas Pipeline Design, Maintenance and Repair
Oil and Gas Pipeline Design, Maintenance and Repair Dr. Abdel-Alim Hashem Professor of Petroleum Engineering Mining, Petroleum & Metallurgical Eng. Dept. Faculty of Engineering Cairo University aelsayed@mail.eng.cu.edu.eg
More informationSPR PE Steel Reinforced Liner
ENGINEERED SOLUTIONS SPR PE Steel Reinforced Liner Reline Done Right Contech is your single source for rehabilitation of sanitary & storm sewers, culverts and bridges. Contech Engineered Solutions has
More informationUltrasonic Guided Waves Evaluation of Trials for Pipeline Inspection
17th World Conference on Nondestructive Testing, 25-28 Oct 2008, Shanghai, China Ultrasonic Guided Waves Evaluation of Trials for Pipeline Inspection Francisco C. R. MARQUES 1, Alessandro DEMMA 2 1 E&P
More informationForces on Large Steam Turbine Blades
Forces on Large Steam Turbine Blades RWE npower Mechanical and Electrical Engineering Power Industry INTRODUCTION RWE npower is a leading integrated UK energy company and is part of the RWE Group, one
More informationFREESTUDY HEAT TRANSFER TUTORIAL 3 ADVANCED STUDIES
FREESTUDY HEAT TRANSFER TUTORIAL ADVANCED STUDIES This is the third tutorial in the series on heat transfer and covers some of the advanced theory of convection. The tutorials are designed to bring the
More informationPRESSURE PIPE REHABILIATION CIPP TECHNOLOGIES
PRESSURE PIPE REHABILIATION CIPP TECHNOLOGIES SEKISUI SPR s rehabilitation technologies for pressure pipelines SEKISUI SPR is synonymous with the development and implementation of trenchless pipe rehabilitation
More informationTechnical Specifications BIO-BLOK 80 HD G
Technical Specifications BIO-BLOK 80 HD G Product: Type BIO-BLOK 80 HD G (80 m 2 /m 3 ). Produced by. Constructed of 8 x 8 net tubes that are subsequently welded Approx. 54 x 54 x 55 cm. 80 m 2 /m 3 in
More informationShaping the Experience of Light SPIRE LIGHT COLUMNS. www.insightlighting.com
Shaping the Experience of Light SPIRE LIGHT COLUMNS www.insightlighting.com 1 CONTENTS SPIRE PRODUCT SPECIFICATIONS & DIMENSIONS 6 SPIRE ORDERING INFORMATION 7 2 www.insightlighting.com SPIRE LIGHT COLUMNS
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.
The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16. Please refer to the publication in its entirety for complete details on this product
More informationScraper Passage Indicator. Electrical Indicator. Features
IV Scraper Passage Indicator Bulletin No: 5110.001.03 Date: June 2008 Cross Indexing No: n/a Supersedes: 5110.001.02 (1/06) Flag Indicator Electrical Indicator Options Description TDW s IV Scraper Passage
More informationPlastic lining by Roschütz
Plastic lining by Roschütz first class corrosion prevention for hollow parts High-quality corrosion protection of hollow parts Hollow part-coating with Teflon, PFA, Tefzel, Halar - approved for best inside
More informationChapter 16. Mensuration of Cylinder
335 Chapter 16 16.1 Cylinder: A solid surface generated by a line moving parallel to a fixed line, while its end describes a closed figure in a plane is called a cylinder. A cylinder is the limiting case
More informationThe Coating Machinery Experts Supplier Questionnaire
Date: Completed by: Company Data 1.1 General Data Full company name, legal form and address: Short form of company name: Country: USt. ID/ VAT Reg./ N.IVA/ NIPIC/ UID Nr./ ID TVA: Company homepage: www.
More informationNON RETURN & FLAP VALVES
RUR UK NON RTURN & P VVS RUR UK The Original and est - Rubber lexible ouplings and ushes INTROUTION P VVS The principle applications for flap valves are for surface water drainage associated with river,
More informationM SERIES REFRIGERANT COIL MODULE REFRIGERANT COILS for R-22, R-407C, R-410A
Bulletin 20-20.2 / July 2012 M SERIES REFRIGERANT COIL MODULE REFRIGERANT COILS for R-22, R-407C, R-410A ➀ ➁ ➂ Model Number Key M 2430 C L 1 - A - ➀ Unit Type M=Modular Nominal Capacity 2430=24000 to 30000
More informationRoyal Seal Gasketed Sewer Pipe
Royal Seal Gasketed Sewer Pipe Royal Seal Gasketed Sewer Pipe Royal Seal gasketed sewer pipe with our specially designed Double Seal Locked-In (DSLI ) gasket is an extremely durable pipe with a leak proof
More informationAre these noise cancelling devices needed to make your chiller quiet??
Are these noise cancelling devices needed to make your chiller quiet?? Not on this chiller! Some sound barriers should never be broken. Government authorities recommend that exposure to loud noise over
More informationCERTIFICATE OF APPROVAL No CF 5055 ARABIAN VERMICULITE INDUSTRIES
CERTIFICATE OF APPROVAL No CF 5055 This is to certify that, in accordance with TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of 1 st Industrial Area,
More informationScuffing Measurement Methodology and Improved Film Coating Systems
OPADRY II Application Data High Performance Film Coating System Scuffing Measurement Methodology and Improved Film Coating Systems PURPOSE Scuffing is a term used to describe coated tablet defects consisting
More informationScrew Plug Immersion Heaters
Immersion Heaters Overview Immersion Heaters consist of hairpin bent tubular elements brazed or welded into a screw plug and provided with terminal enclosures for electrical connections. Immersion Heaters
More informationArmanet BEKAERT. Armanet THE CONSTRUCTIVE IDEA. Render & plaster reinforcing mesh @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@
BEKAERT Armanet THE CONSTRUCTIVE IDEA Armanet Render & plaster reinforcing mesh Armanet Renovation Product specification Insulation Reinforcing Mesh Armanet is a heavily galvanized welded mesh used for
More informationDefining Quality. Building Comfort. Heating and Cooling Coils
Defining Quality. Building Comfort. Heating and Cooling Coils Heating and Cooling Coils Heating and Cooling Coils For over 20 years, AAON has supplied the coil needs of industrial and commercial HVAC customers.
More informationSECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS
SECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS PART 1 GENERAL 1.01 SECTION INCLUDES A. The requirements for pipe material and installation in sewer and drainage collection systems. All materials
More informationAfrica s leading steel supplier CATALOGUE TUBE & PIPE. The Macsteel Group - Africa s leading steel supplier - www.macsteel.co.za
Africa s leading steel supplier CATALOGUE TUBE & PIPE - www.macsteel.co.za TUBE & PIPE CONTENTS 1. Contents 13. Conveyance SANS 1182 - Light Page 7 2. Contact Details 14. Conveyance SANS 719 - Large Bore
More information