Temperature Increase in the. Human Eye When Subjected to a. Laser Source
|
|
- Tyrone Ramsey
- 8 years ago
- Views:
Transcription
1 Validation of a Model to Predict Temperature Increase in the Human Eye When Subjected to a Laser Source Corinna Sue Thompson, Antonio Campo, PhD., University of Vermont, Undergraduate Research Endeavors Competitive Awards September 2006
2 Abstract: Heat transmission and cooling of the human eye has many important scientific and medical applications. From surgery to workplace and laboratory safety, eye protection is key. Mathematical models for the human eye exist with certain limitations on boundary conditions (Campo, Ridouane). Models of and experiments done on other mammals have been shown inadequate in describing the complex mechanisms of the human eye. Progress was made in the 1970 s and 80 s with animal eye experimentation (Lagendijk). Since then, finite volume methods to determine temperature changes and material properties numerically have been implemented to support experimental findings. Information from experimental data is still necessary to utilize and evaluate the results of finite volume analysis. Some variations in temperature due to thermal conductivity and convective coefficient are presented. A thorough understanding of the fundamental physics of the heat transfer is also imperative. The tools available to researchers doing finite volume analysis today are more accurate and faster than those used over the past three decades when similar methods were employed. It is important to reexamine the problem of heat transfer within the eye again using more sophisticated technology. Recent work has focused mainly on developing a sensitivity analysis for the finite volume method so that data presented can be well understood in the context of known uncertainties.
3 Introduction: Current work concerning human eye tissue degeneration in response to heat and light exposure is preliminary. Finite element analysis and variation in temperature calculations have been done assuming the eye is unexposed. In these studies a very simple 2 dimensional geometry representing the eye was used. The tissue in the eye was assumed homogenous and with properties similar to water 1. We plan to continue work that was started by addressing issues of eye exposure and cooling with tears. A similar finite volume method will be used in simulations with varying boundary conditions. Changes will be made addressing the asymmetry of the eye with the optic nerve located just below the hemisphere. Because heating and cooling of the unexposed eye is predominately achieved with blood flow, we will spend some time examining heat transfer with the capillaries adjacent to the eye itself. Our more comprehensive work will have applications in the growing fields of laser eye surgery and new IC chip implantations for the blind. Awareness of heating and cooling mechanisms in the eye aid the materials science and optics industries when formulating eye protection devices. Background: The eye is subject to heat in many ways, but the most harmful heat sources are thought to be infrared radiation (IR) sources, i.e. molten glass and metal, lasers 3. Infrared radiation is divided up into three subgroups: IR-A, IR-B, and IR-C. Each type of radiation corresponds to a to a different range of wavelengths 1. IR-A, near infrared is nm
4 IR-B is nm IR-C, far infrared is nm Figure 1: The different classifications of infrared radiation are absorbed by different tissues within the eye 1. Not all parts of the eye exposed to radiation will absorb the same wavelengths. Tissues within the eye vary in terms of absorption capabilities and resistance to damage. When one type of tissue absorbs the energy, the surrounding tissues are heated by conduction. Under normal conditions, the eye is constantly cooled by convection with blood flow throughout the vasculature and exposure to air and tears at the anterior surface.
5 Figure 2: The anatomy of the human eye 5. Corneal damage is concerning because it absorbs most forms of IR to protect the retina 6. Hypothesis: Many pathologies of the human eye are related to the cellular changes that occur as a result of heat damage 3. Extended exposure to radiation will cause overall temperatures in the eye to increase and affect tissue that does not absorb the radiation 2. Currently, the regulation for exposure may not be strict enough for some purposes and too limiting for others.
6 Figure 3: The electromagnetic spectrum. As wavelengths increase, the energy of the photons decreases 4. Methods: Finite element modeling will be used to impose appropriate boundary conditions on the subject. These boundary conditions can then be varied to model different conditions in the eye 1. (1) The bio-heat transfer equation follows for this model: T ρc = ( k. T ) + H t The mesh size chosen for this model varies as the different tissue and infrared radiation absorbance changes. The model has three boundaries on which to apply conditions, and four points of general interest along the visual axis.
7 The data presented here are for the assumption that the eye is unexposed 1. When one parameter is changed in the simulation, all others are maintained. This is with the purpose of first understanding how these parameters effect temperature variations within the human eye. Data: Table 1: Table 2: Table 3: Tables 1, 2, and 3 show the change in the temperature distribution at points A through D under different boundary and material conditions. They come from work done using the computational program FLUENT by Ridouane and Campo.
8 Discussion: Environmental temperature changes affect temperatures in the different regions of the eye, as seen in table 1. A radiation source in the ambient environment would most likely increase these temperatures even more. Table 2 shows the effect of thermal conductivity on the temperature at the four points. An increased thermal conductivity leads to more heat transferred from an area of high temperature. Table 3 outlines temperature variation due to the change in the convective heat transfer coefficient h s, from the sclera to the center of the eye. A similar table could be generated for the convective heat transfer coefficient h c. When tabulating this data, all other properties of the eye were taken to be the base values found in literature 3. Γ 2 Γ 3 Γ 1 D C B A Figure 4: The finite volume mesh used in simulations 1. Assumptions about the symmetry of the system allow for this simplification in geometry.
9 Conclusions It is essential to have a safe and reliable way to determine these limits. A better understanding of heat transfer in the human eye will lead to improved standards and regulations in industry. This topic will also have an impact on the conditions under which and the details of various laser related eye surgeries 7. Figure 5 corresponds to the base case heating by conduction. The data presented represents a sensitivity study formulated to justify this finite volume analysis. Figure 5: Predicted finite volume results for the steady-state isothermal contours for the healthy human eye 1. Here the temperature shown is in Kelvin.
10 Future work still needs to be done in the area of heat transfer and the tissue of the eye. Ideally, experimental work would be done along side computational and theoretical modeling. Another program, FemLab for example or even a Solid Works add on Flo Works, could be used to validate the above results found using FLUENT. A different program may afford the user more freedom in both geometry and boundary conditions. Acknowledgements: I would like to thank Prof. Antonio Campo for his interest in this project and continued encouragement. El Hassan Ridouane, as well as other members of Dr. Campo s graduate research team, have been valuable and appreciated consults on this topic. We are thankful for the generous support of the Undergraduate Research Endeavors Competitive Award.
11 References 1. Ridouane, E.H., A. Campo, Model for the Heat Transmission in the Human Eye. Proc. of ASME-IMECE, Lagendijk, J.J.W., A mathematical model to calculate temperature distributions in human and rabbit eyes during hyperthermic treatment. Phys. Med. Biol., 1982, 27, Scott, J.A., The computation of temperature rises in the human eye induced by infrared radiation. Phys. Med. Biol., 1988, 33, Electromagnetic spectrum, March 27, Sagital section of the adult human eye, April 5, McCally, R.L., C.B. Bargeron, Corneal Epithelial Injusry Thresholds for Multiple- Pulse Exposures to TM:YAG Laser Radiation at 2.02 um. Health Physics, 2003, 85,
12 7. Cosalia, K., j. Weiland, M. Humayun, G. Lazzi, Thermal Elevation in the Human Eye and Head Due to the Operation of a Retinal Prosthesis. IEEE Trans. On Biomedical Engr., 2004, 51,
NUMERICAL SIMULATION OF BIOHEAT TRANSFER PROCESS IN THE HUMAN EYE USING FINITE ELEMENT METHOD
Scientific Research of the Institute of Mathematics and Computer Science NUMERICAL SIMULATION OF BIOHEAT TRANSFER PROCESS IN THE HUMAN EYE USING FINITE ELEMENT METHOD Marek Paruch Department for Strength
More informationFETD COMPUTATION OF THE TEMPERATURE DIS- TRIBUTION INDUCED INTO A HUMAN EYE BY A PULSED LASER
Progress In Electromagnetics Research, Vol. 120, 403 421, 2011 FETD COMPUTATION OF THE TEMPERATURE DIS- TRIBUTION INDUCED INTO A HUMAN EYE BY A PULSED LASER M. Cvetković 1, *, D. Poljak 1, and A. Peratta
More informationEffects of Cell Phone Radiation on the Head. BEE 4530 Computer-Aided Engineering: Applications to Biomedical Processes
Effects of Cell Phone Radiation on the Head BEE 4530 Computer-Aided Engineering: Applications to Biomedical Processes Group 3 Angela Cai Youjin Cho Mytien Nguyen Praveen Polamraju Table of Contents I.
More informationEFFECTS OF ELECTROMAGNETIC RADIATION FROM MOBILE PHONES AND CASE STUDIES OF COMPUTATIONAL MODELS FOR CALCULATING SAR DISTRIBUTION IN HUMAN BODY Settapong Malisuwan National Broadcasting and Telecommunications
More informationEffect of Blood Perfusion and Metabolism in Temperature Distribution in Human Eye
Advances in Applied Mathematical Biosciences. ISSN 2248-9983 Volume 4, Number 1 (2013), pp. 13-23 International Research Publication House http://www.irphouse.com Effect of Blood Perfusion and Metabolism
More informationNumerical Model for the Study of the Velocity Dependence Of the Ionisation Growth in Gas Discharge Plasma
Journal of Basrah Researches ((Sciences)) Volume 37.Number 5.A ((2011)) Available online at: www.basra-science -journal.org ISSN 1817 2695 Numerical Model for the Study of the Velocity Dependence Of the
More informationMathematical Model: Comparative Study of Thermal Effects of Laser in Corneal Refractive Surgeries
Available at http://pvamu.edu/aam Appl. Appl. Math. ISSN: 1932-9466 Vol. 1, Issue 1 (June 215), pp. 62-633 Applications and Applied Mathematics: An International Journal (AAM) Mathematical Model: Comparative
More informationDefense Technical Information Center Compilation Part Notice
UNCLASSIFIED Defense Technical Information Center Compilation Part Notice ADP020051 TITLE: A Review of Infrared Laser Energy Absorption and Subsequent Healing in the Cornea DISTRIBUTION: Approved for public
More informationMeasuring Optical and Thermal Properties of High Temperature Receivers
www.dlr.de Folie 1 Measuring Optical and Thermal Properties of High Temperature Receivers Johannes Pernpeintner, Thomas Fend 4 th SFERA Summerschool, May 15-16, 2013, Burg Hornberg www.dlr.de Folie 2 Part
More informationME6130 An introduction to CFD 1-1
ME6130 An introduction to CFD 1-1 What is CFD? Computational fluid dynamics (CFD) is the science of predicting fluid flow, heat and mass transfer, chemical reactions, and related phenomena by solving numerically
More informationExpress Introductory Training in ANSYS Fluent Lecture 1 Introduction to the CFD Methodology
Express Introductory Training in ANSYS Fluent Lecture 1 Introduction to the CFD Methodology Dimitrios Sofialidis Technical Manager, SimTec Ltd. Mechanical Engineer, PhD PRACE Autumn School 2013 - Industry
More informationModule 1 : Conduction. Lecture 5 : 1D conduction example problems. 2D conduction
Module 1 : Conduction Lecture 5 : 1D conduction example problems. 2D conduction Objectives In this class: An example of optimization for insulation thickness is solved. The 1D conduction is considered
More informationIntegration of a fin experiment into the undergraduate heat transfer laboratory
Integration of a fin experiment into the undergraduate heat transfer laboratory H. I. Abu-Mulaweh Mechanical Engineering Department, Purdue University at Fort Wayne, Fort Wayne, IN 46805, USA E-mail: mulaweh@engr.ipfw.edu
More informationResearch Article Thermal Analysis of head with Exposure to Electromagnetic Mobile Waves Shahrokh Shojaei l, Nasser Fatouraei l, Gholamreza Ataei 2 * 1
Scholars Academic Journal of Biosciences (SAJB) Sch. Acad. J. Biosci., 2015; 3(4):355-360 Scholars Academic and Scientific Publisher (An International Publisher for Academic and Scientific Resources) www.saspublisher.com
More informationMAKING SENSE OF ENERGY Electromagnetic Waves
Adapted from State of Delaware TOE Unit MAKING SENSE OF ENERGY Electromagnetic Waves GOALS: In this Part of the unit you will Learn about electromagnetic waves, how they are grouped, and how each group
More information1. At which temperature would a source radiate the least amount of electromagnetic energy? 1) 273 K 3) 32 K 2) 212 K 4) 5 K
1. At which temperature would a source radiate the least amount of electromagnetic energy? 1) 273 K 3) 32 K 2) 212 K 4) 5 K 2. How does the amount of heat energy reflected by a smooth, dark-colored concrete
More informationRate of Heating Analysis of Data Centers during Power Shutdown
2011. American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. (www.ashrae.org). Published in ASHRAE Transactions, Volume 117, Part 1. For personal use only. Additional reproduction,
More informationSteady Heat Conduction
Steady Heat Conduction In thermodynamics, we considered the amount of heat transfer as a system undergoes a process from one equilibrium state to another. hermodynamics gives no indication of how long
More informationWhat is Solar Control?
A better environment inside and out. Solar, Safety and Security Window Films: Tech Bulletin Understanding Solar Performance Solar Gard solar control window films use advanced technology to benefit consumers
More informationPrinciple of Thermal Imaging
Section 8 All materials, which are above 0 degrees Kelvin (-273 degrees C), emit infrared energy. The infrared energy emitted from the measured object is converted into an electrical signal by the imaging
More informationThermal Mass Availability for Cooling Data Centers during Power Shutdown
2010 American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. (www.ashrae.org). Published in ASHRAE Transactions (2010, vol 116, part 2). For personal use only. Additional reproduction,
More informationMr. Richard Tell Chair, IEEE SCC28 (SC4) Risk Assessment Work Group Richard Tell Associates, Inc. 8309 Garnet Canyon Lane Las Vegas, NV 89129-4897
DEPARTMENT OF HEALTH AND HUMAN SERVICES Public Health Service National Institute for Occupational Safety and Health Robert A. Taft Laboratories 4676 Columbia Parkway Cincinnati OH 45226-1998 June 17, 1999
More informationCFD Application on Food Industry; Energy Saving on the Bread Oven
Middle-East Journal of Scientific Research 13 (8): 1095-1100, 2013 ISSN 1990-9233 IDOSI Publications, 2013 DOI: 10.5829/idosi.mejsr.2013.13.8.548 CFD Application on Food Industry; Energy Saving on the
More informationTech Bulletin. Understanding Solar Performance
Tech Bulletin Understanding Solar Performance Bekaert solar control window films use advanced technology to benefit consumers with quality solutions that enhance comfort and decrease energy use. By understanding
More informationHeat Transfer and Energy
What is Heat? Heat Transfer and Energy Heat is Energy in Transit. Recall the First law from Thermodynamics. U = Q - W What did we mean by all the terms? What is U? What is Q? What is W? What is Heat Transfer?
More informationMotor-CAD Software for Thermal Analysis of Electrical Motors - Links to Electromagnetic and Drive Simulation Models
Motor-CAD Software for Thermal Analysis of Electrical Motors - Links to Electromagnetic and Drive Simulation Models Dave Staton, Douglas Hawkins and Mircea Popescu Motor Design Ltd., Ellesmere, Shropshire,
More informationTHERMAL RADIATION (THERM)
UNIVERSITY OF SURREY DEPARTMENT OF PHYSICS Level 2 Classical Laboratory Experiment THERMAL RADIATION (THERM) Objectives In this experiment you will explore the basic characteristics of thermal radiation,
More informationThermal Effects of Mobile Phones
Thermal Effects of Mobile Phones S. Kassimi 1, A. ELfadl, S. Bri 3, A. Nakheli 4, M. Habibi 5, M. Ben Ahmed 6 Systems and Telecommunications Engineering Decision Laboratory,Ibn Tofail University, Faculty
More informationA concise guide to Safety Glasses, the different standards and the effects of light on the eye. Contents. Links. Year of publication: 2010
A concise guide to Safety Glasses, the different standards and the effects of light on the eye Year of publication: 2010 Produced by the leading supplier of Safety Glasses in the UK. All Rights Reserved.
More informationHow To Calculate Thermal Resistance On A Pb (Plastipo)
VISHAY BEYSCHLAG Resistive Products 1. INTRODUCTION Thermal management is becoming more important as the density of electronic components in modern printed circuit boards (PCBs), as well as the applied
More informationMEL 807 Computational Heat Transfer (2-0-4) Dr. Prabal Talukdar Assistant Professor Department of Mechanical Engineering IIT Delhi
MEL 807 Computational Heat Transfer (2-0-4) Dr. Prabal Talukdar Assistant Professor Department of Mechanical Engineering IIT Delhi Time and Venue Course Coordinator: Dr. Prabal Talukdar Room No: III, 357
More informationNew Methods of Testing PCB Traces Capacity and Fusing
New Methods of Testing PCB Traces Capacity and Fusing Norocel Codreanu, Radu Bunea, and Paul Svasta Politehnica University of Bucharest, Center for Technological Electronics and Interconnection Techniques,
More informationProduction of X-rays. Radiation Safety Training for Analytical X-Ray Devices Module 9
Module 9 This module presents information on what X-rays are and how they are produced. Introduction Module 9, Page 2 X-rays are a type of electromagnetic radiation. Other types of electromagnetic radiation
More informationINJECTION MOLDING COOLING TIME REDUCTION AND THERMAL STRESS ANALYSIS
INJECTION MOLDING COOLING TIME REDUCTION AND THERMAL STRESS ANALYSIS Tom Kimerling University of Massachusetts, Amherst MIE 605 Finite Element Analysis Spring 2002 ABSTRACT A FEA transient thermal structural
More informationMUCH work has been reported on determining the specific
IEEE TRANSACTIONS ON BIOMEDICAL ENGINEERING, VOL. 46, NO. 8, AUGUST 1999 911 Heating of Tissue by Near-Field Exposure to a Dipole: A Model Analysis Pere J. Riu, Senior Member, IEEE, and Kenneth R. Foster,*
More informationEco Pelmet Modelling and Assessment. CFD Based Study. Report Number 610.14351-R1D1. 13 January 2015
EcoPelmet Pty Ltd c/- Geoff Hesford Engineering 45 Market Street FREMANTLE WA 6160 Version: Page 2 PREPARED BY: ABN 29 001 584 612 2 Lincoln Street Lane Cove NSW 2066 Australia (PO Box 176 Lane Cove NSW
More informationTWO-DIMENSIONAL FINITE ELEMENT ANALYSIS OF FORCED CONVECTION FLOW AND HEAT TRANSFER IN A LAMINAR CHANNEL FLOW
TWO-DIMENSIONAL FINITE ELEMENT ANALYSIS OF FORCED CONVECTION FLOW AND HEAT TRANSFER IN A LAMINAR CHANNEL FLOW Rajesh Khatri 1, 1 M.Tech Scholar, Department of Mechanical Engineering, S.A.T.I., vidisha
More informationTHERMAL DESIGN AND TEST REQUIREMENTS FOR OUTSIDE PLANT CABLE TELECOMMUNICATIONS EQUIPMENT Al Marshall, P.E. Philips Broadband Networks
THERMAL DESIGN AND TEST REQUIREMENTS FOR OUTSIDE PLANT CABLE TELECOMMUNICATIONS EQUIPMENT Al Marshall, P.E. Philips Broadband Networks Abstract Shrinking thermal margins, driven by sophisticated but thermally
More informationIntroduction to CFD Analysis
Introduction to CFD Analysis 2-1 What is CFD? Computational Fluid Dynamics (CFD) is the science of predicting fluid flow, heat and mass transfer, chemical reactions, and related phenomena by solving numerically
More informationMINIMALLY INVASIVE THERMAL THERAPY FOR CANCER TREATMENT BY USING THIN COAXIAL ANTENNAS
MINIMALLY INVASIVE THERMAL THERAPY FOR CANCER TREATMENT BY USING THIN COAXIAL ANTENNAS K. Ito 1, K. Saito 1, T. Taniguchi 2, S. Okabe 2, and H. Yoshimura 1 1 Faculty of Engineering, Chiba University, Chiba,
More informationRefractive Errors & Correction
Super Vision 6 Chapter Lasik is currently the most sophisticated procedure for correction of refractive errors. Lasik is an acronym for Laser Assisted Insitu Keratomileusis. In Lasik, Excimer laser is
More informationIntroduction to CFD Analysis
Introduction to CFD Analysis Introductory FLUENT Training 2006 ANSYS, Inc. All rights reserved. 2006 ANSYS, Inc. All rights reserved. 2-2 What is CFD? Computational fluid dynamics (CFD) is the science
More informationThe Three Heat Transfer Modes in Reflow Soldering
Section 5: Reflow Oven Heat Transfer The Three Heat Transfer Modes in Reflow Soldering There are three different heating modes involved with most SMT reflow processes: conduction, convection, and infrared
More informationDepartment of Engineering Enzo Ferrari University of Modena and Reggio Emilia
Department of Engineering Enzo Ferrari University of Modena and Reggio Emilia Object: Measurement of solar reflectance, thermal emittance and Solar Reflectance Index Report Reference person: Alberto Muscio
More informationHEAT TRANSFER ANALYSIS IN A 3D SQUARE CHANNEL LAMINAR FLOW WITH USING BAFFLES 1 Vikram Bishnoi
HEAT TRANSFER ANALYSIS IN A 3D SQUARE CHANNEL LAMINAR FLOW WITH USING BAFFLES 1 Vikram Bishnoi 2 Rajesh Dudi 1 Scholar and 2 Assistant Professor,Department of Mechanical Engineering, OITM, Hisar (Haryana)
More informationEMR Exposure Limits & Assessment Methods for Mobile Phone Communications. Lindsay Martin Manager, Non-Ionising Radiation Section
EMR Exposure Limits & Assessment Methods for Mobile Phone Communications Lindsay Martin Manager, Non-Ionising Radiation Section Introduction How can we use Wireless Communication Safely? Wireless communication
More informationNon-Ionizing Electromagnetic Radiation
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike License. Your use of this material constitutes acceptance of that license and the conditions of use of materials on this
More informationCurrent Staff Course Unit/ Length. Basic Outline/ Structure. Unit Objectives/ Big Ideas. Properties of Waves A simple wave has a PH: Sound and Light
Current Staff Course Unit/ Length August August September September October Unit Objectives/ Big Ideas Basic Outline/ Structure PS4- Types of Waves Because light can travel through space, it cannot be
More informationConductive and Radiative Heat Transfer in Insulators
Conductive and Radiative Heat Transfer in Insulators Akhan Tleoubaev, Ph.D. LaserComp, Inc., December 1998 Heat transfer for most thermal insulation materials occurs via both conduction and radiation.
More informationNumerical simulation of the utility glass press-andblow
Numerical simulation of the utility glass press-andblow process Introduction STEKLÝ, J., MATOUŠEK, I. Glass melt press-and-blow process is a typical two stage technology allowing automatized production
More informationTemperature Distribution upon Corneal Surface during Laser Eye Surgery, a Comparative Study
American Journal of Biomedical Engineering 2013, 3(6): 220-226 DOI: 10.5923/j.ajbe.20130306.11 Temperature Distribution upon Corneal Surface during Khalid A. Joudi 1, Somer M. Nacy 2, Nebras H. Ghaeb 2,*
More informationStatement of the Chief Medical Health Officer
Statement of the Chief Medical Health Officer June, 2011 Health Concerns About Cellular Phone Transmission Antennae and Base Stations In 2005, in response to community concerns and after reviewing the
More informationExplaining Ellipse I 2 PL
Explaining Ellipse I 2 PL CLINICALLY PROVEN SAFE AND EFFECTIVE Ellipse I 2 PL stands for Ellipse secondgeneration Intense Pulsed Light The Ellipse I 2 PL system is used for the treatment of a wide range
More informationModel Order Reduction for Linear Convective Thermal Flow
Model Order Reduction for Linear Convective Thermal Flow Christian Moosmann, Evgenii B. Rudnyi, Andreas Greiner, Jan G. Korvink IMTEK, April 24 Abstract Simulation of the heat exchange between a solid
More informationUltraviolet (UV) Radiation Safety
Ultraviolet (UV) Radiation Safety April 2005 Compiled by Myung Chul Jo Environmental Health and Safety University of Nevada Reno Page 1 of 8 Table of Contents 1. UVRadiation 3 2. Common sources of UV radiation
More informationDefinition and Evaluation of Mean Beam Lengths for Applications in Multidimensional Radiative Heat Transfer: A Mathematically Self-Consistent Approach
Definition and Evaluation of Mean Beam Lengths for Applications in Multidimensional Radiative Heat Transfer: A Mathematically Self-Consistent Approach Walter W. Yuen Department of Mechanical Engineering,
More informationFrom lowest energy to highest energy, which of the following correctly orders the different categories of electromagnetic radiation?
From lowest energy to highest energy, which of the following correctly orders the different categories of electromagnetic radiation? From lowest energy to highest energy, which of the following correctly
More informationPHOTOELECTRIC EFFECT AND DUAL NATURE OF MATTER AND RADIATIONS
PHOTOELECTRIC EFFECT AND DUAL NATURE OF MATTER AND RADIATIONS 1. Photons 2. Photoelectric Effect 3. Experimental Set-up to study Photoelectric Effect 4. Effect of Intensity, Frequency, Potential on P.E.
More informationAmpacity simulation of a high voltage cable to connecting off shore wind farms
Ampacity simulation of a high voltage cable to connecting off shore wind farms Eva Pelster 1, Dr. David Wenger 1 1 Wenger Engineering GmbH, Einsteinstr. 55, 89077 Ulm, mail@wenger-engineering.com Abstract:
More informationHuman Exposure Limits
Human Exposure Limits Session 3 0 Version December 2014 Learning objectives In this session we will: Learn about the international exposure limits for workers and the public Learn about methods for assessing
More informationFDTD Computation of Sar Distributions in Human Head for Mobile Phones V.Purushothaman, N.Vignesh, S.Vijayakumar
FDTD Computation of Sar Distributions in Human Head for Mobile Phones V.Purushothaman, N.Vignesh, S.Vijayakumar Veltech Engineering College, purushothamanece@gmail.com, Vicky.ganapathy@gmail.com,vijayeee333@gmail.com
More informationCHAPTER 2 Energy and Earth
CHAPTER 2 Energy and Earth This chapter is concerned with the nature of energy and how it interacts with Earth. At this stage we are looking at energy in an abstract form though relate it to how it affect
More informationCalculation of Liquefied Natural Gas (LNG) Burning Rates
Calculation of Liquefied Natural Gas (LNG) Burning Rates Carolina Herrera, R. Mentzer, M. Sam Mannan, and S. Waldram Mary Kay O Connor Process Safety Center Artie McFerrin Department of Chemical Engineering
More informationLASER MELTED STEEL FREE SURFACE FORMATION
METALLURGY AND FOUNDRY ENGINEERING Vol. 33, 2007, No. 1 Aleksander Siwek * LASER MELTED STEEL FREE SURFACE FORMATION 1. INTRODUCTION Many phisical phenomena happen on the surface of worked object in the
More informationQ1. The diagram below shows the range of wavelengths and frequencies for all the types of radiation in the electromagnetic spectrum.
Q. The diagram below shows the range of wavelengths and frequencies for all the types of radiation in the electromagnetic spectrum. X rays, which have frequencies in the range 0 8 0 2 Hz are already marked
More informationEssay 5 Tutorial for a Three-Dimensional Heat Conduction Problem Using ANSYS Workbench
Essay 5 Tutorial for a Three-Dimensional Heat Conduction Problem Using ANSYS Workbench 5.1 Introduction The problem selected to illustrate the use of ANSYS software for a three-dimensional steadystate
More informationINTERNATIONAL ASSOCIATION OF CLASSIFICATION SOCIETIES. Interpretations of the FTP
INTERNATIONAL ASSOCIATION OF CLASSIFICATION SOCIETIES Interpretations of the FTP CONTENTS FTP1 Adhesives used in A or B class divisions (FTP Code 3.1, Res A.754 para. 3.2.3) June 2000 FTP2 Pipe and duct
More informationPulsed laser deposition of organic materials
Pulsed laser deposition of organic materials PhD theses Gabriella Kecskeméti Department of Optics and Quantum Electronics University of Szeged Supervisor: Dr. Béla Hopp senior research fellow Department
More informationRediscover quality of life thanks to vision correction with technology from Carl Zeiss. Patient Information
Rediscover quality of life thanks to vision correction with technology from Carl Zeiss Patient Information 5 2 It was really w Vision defects: Light that goes astray For clear vision the eyes, cornea and
More informationLaserwelding of plastics Ir. Luc Janssen 2008
3D Laserwelding page 1 of 12 Laserwelding of plastics Ir. Luc Janssen 2008 1 Laserwelding - How it works Laserwelding is a very versatile process and is suitable for both small series and massproduction.
More informationIterative calculation of the heat transfer coefficient
Iterative calculation of the heat transfer coefficient D.Roncati Progettazione Ottica Roncati, via Panfilio, 17 44121 Ferrara Aim The plate temperature of a cooling heat sink is an important parameter
More informationFrost Damage of Roof Tiles in Relatively Warm Areas in Japan
Frost Damage of Roof Tiles in Relatively Warm Areas in Japan Influence of Surface Finish on Water Penetration Chiemi IBA Hokkaido Research Organization, Japan Shuichi HOKOI Kyoto University, Japan INTRODUCTION
More informationCCTech TM. ICEM-CFD & FLUENT Software Training. Course Brochure. Simulation is The Future
. CCTech TM Simulation is The Future ICEM-CFD & FLUENT Software Training Course Brochure About. CCTech Established in 2006 by alumni of IIT Bombay. Our motive is to establish a knowledge centric organization
More informationGreen Heating. Pupil Research Brief. Teachers Notes. Syllabus Coverage Subject Knowledge and Understanding. Route through the Brief UPIL ESEARCHER
R P UPIL ESEARCHER Green Heating I NITIATIVE Pupil Research Brief Teachers Notes Syllabus Coverage Subject Knowledge and Understanding all types of electromagnetic radiation form a continuous spectrum
More informationEnvironmental Health and Safety
Environmental Health and Safety Standard Operating Guideline RF & Microwave Safety Program 1.0 Purpose and Requirements This guide will present a summary of the basics of radiofrequency (RF) and microwave
More informationINFLUENCE OF AVERAGING MASSES ON CORRELATION BETWEEN MASS-AVERAGED SAR AND TEMPERATURE RISE
INFLUENCE OF AVERAGING MASSES ON CORRELATION BETWEEN MASS-AVERAGED SAR AND TEMPERATURE RISE A. Razmadze, L. Shoshiashvili, D. Kakulia, R. Zaridze Tbilisi State University, Tbilisi, 0128, Georgia, lae@laetsu.org
More informationFiber Optics: Fiber Basics
Photonics Technical Note # 21 Fiber Optics Fiber Optics: Fiber Basics Optical fibers are circular dielectric wave-guides that can transport optical energy and information. They have a central core surrounded
More information- thus, the total number of atoms per second that absorb a photon is
Stimulated Emission of Radiation - stimulated emission is referring to the emission of radiation (a photon) from one quantum system at its transition frequency induced by the presence of other photons
More information703-0148 InGaN / Sapphire White Water clear. Parameter Rating Unit
Package Dimensions: * All dimensions are in mm * Tolerance: ±.6mm unless otherwise noted. LED Chip Lens Colour Ant Part No. Material Colour Coordinates 73-148 InGaN / Sapphire White Water clear Absolute
More informationHeat Transfer and Thermal-Stress Analysis with Abaqus
Heat Transfer and Thermal-Stress Analysis with Abaqus 2016 About this Course Course objectives Upon completion of this course you will be able to: Perform steady-state and transient heat transfer simulations
More informationThe upcoming new editions of IEC 60825-1 and ANSI Z136.1 examples on impact for classification and exposure limits
ILSC 2011 Conference Proceedings ILSC 2013 Conference Proceedings The upcoming new editions of IEC 60825-1 and ANSI Z136.1 examples on impact for classification and exposure limits Karl Schulmeister Please
More informationEducational Tool for Medical Laser Programs 1. Laser Safety
Educational Tool for Medical Laser Programs 1 Laser Safety Dangers and hazards associated with the use of surgical laser systems require appropriate safety precautions and policies. The success of any
More informationEnergy. Mechanical Energy
Principles of Imaging Science I (RAD119) Electromagnetic Radiation Energy Definition of energy Ability to do work Physicist s definition of work Work = force x distance Force acting upon object over distance
More information2 Absorbing Solar Energy
2 Absorbing Solar Energy 2.1 Air Mass and the Solar Spectrum Now that we have introduced the solar cell, it is time to introduce the source of the energy the sun. The sun has many properties that could
More informationAn Investigation of the Radiative Heat Transfer through Nonwoven Fibrous Materials
An Investigation of the Radiative Heat Transfer through Nonwoven Fibrous Materials Imad Qashou 1, Hooman Vahedi Tafreshi 2, Behnam Pourdeyhimi 3 1 Fiberweb Inc., Old Hickory, Tennessee, USA 2 Mechanical
More informationBiomedical Optics Theory
Introduction Biomedical Optics Theory Diffuse reflectance spectroscopy (DRS) and Laser Doppler Flowmetry (LDF) are booth optical techniques that can quantify a number of microcirculatory parameters. Prof
More informationOverview. What is EMR? Electromagnetic Radiation (EMR) LA502 Special Studies Remote Sensing
LA502 Special Studies Remote Sensing Electromagnetic Radiation (EMR) Dr. Ragab Khalil Department of Landscape Architecture Faculty of Environmental Design King AbdulAziz University Room 103 Overview What
More informationCustomer Training Material. Lecture 2. Introduction to. Methodology ANSYS FLUENT. ANSYS, Inc. Proprietary 2010 ANSYS, Inc. All rights reserved.
Lecture 2 Introduction to CFD Methodology Introduction to ANSYS FLUENT L2-1 What is CFD? Computational Fluid Dynamics (CFD) is the science of predicting fluid flow, heat and mass transfer, chemical reactions,
More informationPHYS 222 Spring 2012 Final Exam. Closed books, notes, etc. No electronic device except a calculator.
PHYS 222 Spring 2012 Final Exam Closed books, notes, etc. No electronic device except a calculator. NAME: (all questions with equal weight) 1. If the distance between two point charges is tripled, the
More informationHigh Resolution Spatial Electroluminescence Imaging of Photovoltaic Modules
High Resolution Spatial Electroluminescence Imaging of Photovoltaic Modules Abstract J.L. Crozier, E.E. van Dyk, F.J. Vorster Nelson Mandela Metropolitan University Electroluminescence (EL) is a useful
More informationEffects of Mobile Phone Radiation onto Human Head with Variation of Holding Cheek and Tilt Positions
Effects of Mobile Phone Radiation onto Human Head with Variation of Holding Cheek and Tilt Positions M. R. Iqbal-Faruque* 1, N. Aisyah-Husni 2, Md. Ikbal-Hossain 1, M. Tariqul-Islam 2 and N. Misran 2 1
More informationDevelopment of Specialized Modelling Tools for Crystal Growth Processes
International Scientific Colloquium Modelling for Material Processing Riga, June 8-9, 2006 Development of Specialized Modelling Tools for Crystal Growth Processes A. Rudevics, A. Muiznieks, B. Nacke, V.
More informationSEMIAUTOMATIC SURFACE REFLECTANCE MEASUREMENT FOR MONITORING OF MATERIAL WEATHERING
SEMIAUTOMATIC SURFACE REFLECTANCE MEASUREMENT FOR MONITORING OF MATERIAL WEATHERING V. Kocour 1, J. Valach 2 1 Motivation Summary: We present a device for measurement of surface reflectance in dependence
More informationRadiation Transfer in Environmental Science
Radiation Transfer in Environmental Science with emphasis on aquatic and vegetation canopy media Autumn 2008 Prof. Emmanuel Boss, Dr. Eyal Rotenberg Introduction Radiation in Environmental sciences Most
More informationKresimir Bakic, CIGRE & ELES, Slovenia
"Maintenance SLOVENIJA and recovery 2014 of HV electricity transport systems and aerospace assistance" STATE-OF-THE-ART FOR DYNAMIC LINE RATING TECHNOLOGY Future Vision Kresimir Bakic, CIGRE & ELES, Slovenia
More informationEnergy Transport. Focus on heat transfer. Heat Transfer Mechanisms: Conduction Radiation Convection (mass movement of fluids)
Energy Transport Focus on heat transfer Heat Transfer Mechanisms: Conduction Radiation Convection (mass movement of fluids) Conduction Conduction heat transfer occurs only when there is physical contact
More informationComparative Analysis of Gas Turbine Blades with and without Turbulators
Comparative Analysis of Gas Turbine Blades with and without Turbulators Sagar H T 1, Kishan Naik 2 1 PG Student, Dept. of Studies in Mechanical Engineering, University BDT College of Engineering, Davangere,
More informationReview Vocabulary spectrum: a range of values or properties
Standards 7.3.19: Explain that human eyes respond to a narrow range of wavelengths of the electromagnetic spectrum. 7.3.20: Describe that something can be seen when light waves emitted or reflected by
More informationEffect of design parameters on temperature rise of windings of dry type electrical transformer
Effect of design parameters on temperature rise of windings of dry type electrical transformer Vikas Kumar a, *, T. Vijay Kumar b, K.B. Dora c a Centre for Development of Advanced Computing, Pune University
More information