Pressure and flow control system

Transcription

1 Pressure and flow control system RE 30030/ /32 Replaces: RE 30024/11.03 RE 30027/06.04 RE 30030/01.04 Type SYDFE1, SYDFEE, SYDFEC, SYDFEn Size 18 to 140 Component series 2X Maximum operating pressure 280 bar H6707_d SYDFE1-2X..., VT 5041 H7111_d SYDFEC-2X... Table of contents Features Contents Page Features 1 Ordering code 2 to 7 Sections 8 Schematic diagrams 9 to 11 Technical data 12 to 13 Electrical connection 14 to 16 Closed control loop quality 17 Transition function 17 to 18 Unit dimensions: SYDFE to 20 Unit dimensions: Combination pumps 21 Hubs for through-drives 22 Unit dimensions: Through-drives 23 to 29 Torsionally flexible couplings for the connection to a standard electric motor 30 Project planning information 31 Further information on this control system 31 n SYDFE.-2X control system is used for the electro-hydraulic control of swivel angle, pressure and power (optional extra on some variants, see pages 4 and 7) of an axial piston unit. The control system consists of the following components: - 10VSO axial piston pump - VT-DFP.-2X proportional valve as pilot valve including inductive position transducers for the valve position measurement. In the SYDFEE, SYDFEC, and SYDFEn versions, the pilot valve comprises electronics for controlling the system. - For SYDFE1: nalog amplifier VT 5041 for realizing all electrical functions necessary for the SYDFE1-2X (separate order) - Position transducer for sensing the swivel angle - pressure transducer with suitable signal level and dynamics (optionally HM 16, otherwise separate order) - Preload valve with integrated pressure limitation function SYDZ (optional) Information on available spare parts:

2 2/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Ordering code: Pump of the SYDFE control system SYDFE.-2X/ 071 R - P R 12 N See following pages 1 Series Control system for external analog electronics (separate order) Control system with internal analog electronics Control system with internal digital electronics Control system with internal digital electronics, speed variable Pump combinations (see order example page 6) SYDFE1-2X SYDFEE-2X SYDFEC-2X SYDFEn-2X SY2DFE.-2X, SY3DFE.-2X Size, type code Displacement cm³ Direction of rotation viewed to drive shaft Right R Left L Hydraulic fluid 4 Mineral oil according to DIN (HL/HLP) P 5 6 Design of the drive shaft Cylindrical with key DIN 6885 (not in connection with through-drive) Ø18 Ø22 Ø25 Ø32 Ø40 Ø45 P Splined shaft profile SE J 744 1) 3/ ½ 1¾ S Splined shaft profile SE J 744 (higher torque) - 7/8 1 1¼ - - R Connection flange Diameter centering in mm ISO 2-hole ISO 4-hole B SE 2-hole C SE 4-hole D Connection for service lines, pressure port B and suction port S 7 SE, laterally opposing mounting thread, metric 12 8 Through-drive (in the case of single pumps, all through-drives are provided without hub, but with end cover to ensure operational safety) Without through-drive N00 Centering Built-on pump 2) (examples) IS0 Ø 100 mm 10VSO..31 size 28/45 - KD3 IS0 Ø 125 mm 10VSO..31 size 71/ KD5 IS0 Ø 180 mm 10VSO..31 size KD7 SE Ø mm 10VSO..31 size 18, PGF2, PGH2, PGH3, ZPF KC1 SE Ø mm PGH4, 1PF2G3, PGF3 - KC3 SE Ø 127 mm PGH KC5 SE Ø mm 10VO KC6 9 Design of the base pump Standard (internal pilot oil) 0000 External supply External supply + regenerative operation = vailable - = Not available Standard program 1) NSI B92.1a-1976, 30 meshing angle, flattened root, side fit, tolerance class 5 2) Please also observe the notes on the pump series on page 22.

3 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 3/32 Ordering code: Pilot and preload valve of the SYDFE1 control system SYDFE1-2X/ 071 R - P R 12 N X0XX 2 - * Spool design Standard 2-groove spool 4-groove spool B C Mounting direction, solenoid 11 Mating connector is radial to the pump axis 0 12 Features not used at the moment X0XX 13 Preload valve with integrated pressure limitation Pressure limitation 200 bar 1 Pressure limitation 250 bar 2 Pressure limitation 300 bar 3 Without preload valve X 14 Further details in the plain text e.g. SO variant

4 4/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Ordering code: Pilot and preload valve of the SYDFEE control system SYDFEE-2X/ 071 R - P R 12 N F L 2 - * Spool design Standard 4-groove spool C Integrated electronics, mounting direction (see below) Radial to the pump axis 0 90 folded in the direction of the connection plate 2 Closed-loop control, additional function B C D Switchable pressure controller (high signal) Power limitation adjustable on the OBE valve B Power limitation adjustable via analog input C Disconnectible pressure controller (high signal) D Electronics assembly, option Standard electronics with leakage oil compensation Standard electronics without leakage oil compensation Plug-in connector ctual pressure value input (Description of the plug-in connectors on page 14) Current input m X1 C Voltage input V X1 V Voltage input V X1 E Voltage input V X2 F Pressure transducer HM 16, measurement range 315 bar ( V) with connecting cable 0.5 m for direct connection to X L Without pressure transducer X Preload valve with integrated pressure limitation Pressure limitation 200 bar 1 Pressure limitation 250 bar 2 Pressure limitation 300 bar 3 Without preload valve X m V V V 17 Further details in the plain text e.g. SO variant Note on feature 11: Mounting direction of the valve electronics Direction of rotation clockwise, mounting direction 0 mounting direction Direction of rotation clockwise, 2 Direction of rotation counterclockwise, mounting direction 0 Direction of rotation counterclockwise, mounting direction 2

5 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 5/32 Ordering code: Pilot and preload valve of the SYDFEC/SYDFEn control system SYDFEC-2X/ 071 R - P R 12 N F L 2 - * Spool design 10 Standard 11 Valve, mounting direction integrated electronics (see below) Radial to the pump axis 0 90 folded in the direction of the subplate 2 dditional functions 12 Standard Electronics assembly, options 13 Standard ctual pressure value input Factory parameter setting (Description of the plug-in connectors on page 15 and 16) Current input m X1 C Voltage input V X1 V Voltage input V X1 E Voltage input V 1) X2 F Plug-in connector Pressure transducer HM 16, measurement range 315 bar ( V) with connecting cable 0.5 m for direct connection to X2 L Without pressure transducer X Preload valve with integrated pressure limitation Pressure limitation 200 bar 1 Pressure limitation 250 bar 2 Pressure limitation 300 bar 3 Without preload valve X m V V V 17 Further details in the plain text e.g. SO variant Note on feature 11: Mounting direction of the valve electronics Direction of rotation clockwise, mounting direction 0 mounting direction Direction of rotation clockwise, 2 Direction of rotation counterclockwise, mounting direction 0 Direction of rotation counterclockwise, mounting direction 2 1) For the SYDFEn control system with analog interfaces the plug-in connector X2 cannot be used as actual pressure value input. Therefore a separate pressure transducer has to be used and connected to the plug-in connector X1 in this case.

6 6/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Ordering code: Order examples Order example for single pump: SYDFEE-2X/100R-PS12N VXX Order example for pump combination: Both material numbers resp. type designations have to be connected with +. Main pump (1st pump) + Built-on pump (2nd pump) SY2DFEE-2X/ / SY2DFEE-2X/ / SYDFEE-2X/100R-PS12KD CXX + SYDFEE-2X/100R-PS12KD CXX Double pump Size of the main pump Size of the built-on pump Material number without R9 for the main pump or type designation in the case of material number not being known Pump combination, mounted with accessories Material number without R9 for the built-on pump or type designation in the case of material number not being known Example of nameplate of a pump combination SY2DFEC Word mark Material short text Material number, including serial number Fabrication job order number Designation of origin Fabrication number MNR: R SN: 1 FD: 09W10 SY2DFEC-2X/ / Made in Germany SN MDE ROT- TION Date of manufacture Plant Indication of direction of rotation Production site Note: For further inquiries with regard to the control system the material number, fabrication order number, serial number and date of manufacture are necessary.

7 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 7/32 Ordering code: ccessories Status as per 4/2009, ask for availability ccessories for SYDFE1 Material number Data sheet mplifier card VT5041-2X/1 without power limitation, without swivel angle indication R RE mplifier card VT5041-2X/3 without power limitation, with swivel angle indication R RE Mating connector for solenoid plug-in connector R Mating connector for valve position transducer R Mating connector for pump position transducer R Pressure transducer HM 12-1X measurement range 315 bar ( m) R RE Pressure transducer HM 13-1X measurement range 315 bar ( V) R RE Pressure transducer HM 17-1X measurement range 315 bar ( m) R RE Pressure transducer HM 17-1X measurement range 315 bar ( V) R RE Card holder VT X/32D R RE Compact power supply unit VT-NE32-1X R RE ccessories for SYDFEE, SYDFEC and SYDFEn Material number Data sheet Mating connector 12-pole for central connection X1 without cable (construction set) R Mating connector 12-pole for central connection X1 with cable set 2 x 5 m R Mating connector 12-pole for central connection X1 with cable set 2 x 20 m R Pressure transducer HM 12-1X measurement range 315 bar ( m) R RE Pressure transducer HM 13-1X measurement range 315 bar ( V) R RE Pressure transducer HM 17-1X measurement range 315 bar ( m) R RE Pressure transducer HM 17-1X measurement range 315 bar ( V) R RE Test device VT-PDFE-1-1X/V0/0 for SY(H)DFEE and SY(H)DFEC R RE B Compact power supply unit VT-NE32-1X R RE ccessoires only for SYDFEC and SYDFEn (serial access) Material number Data sheet Converter USB/serial for laptops without serial interface R VT-ZKO-USB/S-1-1X/V0/0 Cable for connecting a WIN-PED PC (RS232) to the interface X2 length 3 m R T-connector for simultaneous connection of a Win PED PC (RS232) and use of the input at plug-in connector X2 R Further accessories Page Hubs for through-drives 22 Torsionally flexible couplings for the connection to a standard electric motor 30

8 8/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Section 1 Swash plate 2 Pilot valve 3 Counter piston 4 ctuating piston 5 Spring 6 Inductive position transducer for valve position 7 Swivel angle position transducer 8 Proportional solenoid 9 Valve spool 10 Spring 11 Integrated electronics 12 Connector X1 13 Connector X2 for connecting the pressure transducer HM 16 (for SYDFEE only for actual pressure value input F, for SYDFEC and SYDFEn always available) 14 Mating connector X3 for connecting the CN bus (only available on SYDFEC and SYDFEn) 15 Drive shaft 16 Connection flange 17 Connection plate, optionally with through-drive SYDFE1-2X 4 2 SYDFEE-2X SYDFEC-2X SYDFEn-2X T P T P

9 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 9/32 Schematic diagram: SYDFE1-2X, actuator system internally supplied ctuator (q V ; p) P U/I Pressure transducer 1) P1 MP1 Preload valve (optional) nalog amplifier 1) T 20 bar P T T VT5041-2X Pressure command value V (Power command value V) 2) Swivel angle command value 0 ( 10 V) V P PP Enable Error Bleeding P T s U (Details of the electric wiring see data sheet RE 30241) P B s U M Pump S L1 L 1) Separate order 2) Optional

10 10/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Schematic diagram: SYDFEE-2X, SYDFEC-2X, SYDFEn-2X, actuator system internally supplied ctuator (q V ; p) P1 P1 MP1 Preload valve (optional) T 20 bar P T T P U/I Optional 1) Pressure transducer P PP Bleeding Pilot valve VT-DFP...-2X/... Signal exchange with the control (see page 14 to 16) P T s U B P U s M Pump S L1 L 1) When using the pressure transducer HM 16: Installation in P (pump) or MP1 (preload valve) in connection with electronics version actual pressure value input F. When using an external pressure transducer: Installation in the P1 line (preferably near the actuator) and the electrical connection via the central connector When using a preload valve, the pressure transducer has to be connected to P1 or MP1.

11 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 11/32 Schematic diagram: SYDFE1-2X, actuator system externally supplied p max T P ctuator (q V ; p) P1 Optional 2) The illustration shows an example with integrated electronics (SYDFEE, SYDFEC and SYDFEn). The external supply of the actuator system is also possible with external electronics (SYDFE1). 3) P U/I Pressure transducer Pilot valve VT-DFP...-2X/... Signal exchange with the control (see page 14 to 16) P T s U B P P 20 bar 4) U s Z (external pilot oil pressure) M Pump 1) P 0,2 bar S S L1 L 1) The use of a pressure relief and anti-cavitation valve (check valve with 0.2 bar spring) is absolutely necessary in order to avoid dry running in case of a fault. 3) The maximum pressure limitation has to be provided by the customer! 4) Please observe the upper limit for the external pilot oil pressure! (see operating instructions), recommendation: 20 bar absolute. 2) Pressure transducer Mounting option Remark HM 16 P Only in connection with actual pressure value input F HM 12 / HM 13 / HM 17 P1 Preferably near the actuator Important notes on external supply: With an actuator system with external supply the pump does not swivel to zero stroke but to the negative stop in the case of voltage breakdown (100 % flow displaced from the system into the tank). In the case of an active fault signal the machine control absolutely has to react (e.g. switch off drive motor of the pump, interrupt external supply of the actuator system). Command values for pressure and flow always have to be greater than zero (pcommand 3 bar, αcommand 5 %), since no exact pressure zero or swivel angle zero is available due to drift or tolerances. The provision of smaller command values may lead to cavitation in the worst case. The actual pressure value must not be less than 10 bar for longer than 10 minutes (lubrication).

12 12/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Technical data (For applications outside these parameters, please consult us!) mechanical and hydraulic Size / displacement V g max [cm 3 ] Maximum speed 1) n 0 max [min -1 ] Minimum speed n min 50 min -1 Max. flow (displacement) at max. speed q v0 max [l/min] at n E = 1500 min 1 [l/min] Max. power (Δp = 280 bar) at max. speed P 0 max [kw] at n E = 1500 min 1 [kw] Max. torque (Δp = 280 bar, n 0 max ) T max [Nm] Max. admissible drive torque Keyed shaft T Ov [Nm] Splined shaft S overall torque T Ov [Nm] Max. adm. through-drive torque T T [Nm] Splined shaft R overall torque T Ov [Nm] Max. adm. through-drive torque T T [Nm F q Load on the drive shaft ± F ax max. adm. axial force F ax max [N] X/2 X/2 max. admissible radial force 2) F r [N] Weight: Pump without through-drive, including pilot valve m [kg] dditionally, preload valve m [kg] dditionally, in the case of external supply m [kg] Moment of inertia around drive axis [kgm 2 ] Filling capacity of the housing [l] Maximum admissible operating pressure 3) p max 280 bar Minimum operating pressure: with preload valve p min 1 bar without preload valve p min 20 bar in the case of external supply (20 bar) > 10 bar for continuous operation; for operation below p min 10 bar, please observe notes on page 11 dmissible inlet pressure p bar Hydraulic fluid Mineral oil (HL, HLP) according to DIN Hydraulic fluid temperature range ϑ Maximum admissible degree of contamination of the hydraulic fluid according to ISO 4406 Class 18/16/13 (for particle size 4/6/14 μm) Speed n/n 0max 1,2 1,1 1,0 1,6 1,4 1,2 1,0 0,9 Inlet pressure p abs [bar] 1) The values are valid for an absolute pressure of 1 bar in suction port S. When reducing the displacement or increasing the inlet pressure the speed can be increased in accordance with the following characteristic curve. t a reduced inlet pressure the speed has to be reduced. 2) In the case of higher radial forces, please consult us 3) In the case of higher pressures, please consult us 0,9 0,8 0,7 0,8 0,9 1,0 Displacement V g /V gmax

13 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 13/32 Technical data (For applications outside these parameters, please consult us!) electrical The electrical features of the SYDFE1 are described in the data sheet RE Type SYDFEE...2X SYDFEC...2X SYDFEn...2X Operating voltage U B 24 VDC +40 % 5 % Operating range (short-time operation) 24 VDC +40 % 5 % Upper limit value U B (t) max 35 V Lower limit value U B (t) min 21 V Current consumption (in the steady-state operation) Rated current I Rat 0.6 Maximum current I max 1.25 Inputs Outputs ctual pressure value input X1; pin 10 and 11 U or I Determination by means of type code 24 VDC +40 % 5 % Parameterizable: m; m; V; 0 5 V; V; V; V nalog current input, load R B 100 Ω 100 Ω 100 Ω nalog voltage inputs R E 50 kω 100 kω 100 kω Digital inputs Logic V 8 V 8 V Logic 1 21 V 14 V 14 V p ct / U OUT 1 1) U I max 0 10 V 1.5 m ±10 V 2 m α ct / U OUT 2 2) U I max ±10 V 1.5 m ±10 V 2 m Digital outputs Logic 0 U a < 1 V Logic 1 ±10 V 2 m ±10 V 2 m U a U B 5 V; 10 m (short-circuit-proof) mbient temperature range at the pump ϑ C 0 50 C Storage temperature range (pump electronics) ϑ Form of electronics Integrated in the pivot valve (OBE) Electrical connection see page 14 to 16 Type of protection according to EN Pump including pivot valve IP 65 with plug-in connectors mounted and locked Note: Information on environment simulation testing in the fields of EMC (electro-magnetic compatibility), climate and mechanical stress, see RE U (declaration on environmental compatibility). 1, 2) Outputs are parameterizable for SYDFEC and SYDFEn, for factory settings, page 15 / 16

14 14/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Electrical connection: SYDFEE...2X The electrical connection of the SYDFE1 control system is described in data sheet RE X1: Central connection Mating connector according to EN (12-pin), ordering code, see section accessories on page Pinout of connector or mating connector and cable set Pin Signal Description Signal direction Signal type Pinout in the cable set (accessories) 1 +U B Voltage supply IN 24 V DC 1 Supply 2 0 V = L0 Reference potential for voltage supply - 2 line 3 x PE Earth Earthing connection for the electronics - Green / yellow 1.0 mm ² 3 Fault Indicates faults, e.g. cable break of command/actual OUT value cables, controller monitoring (logic 0 = error) Logic 24 V White 4 M0 Reference potential for analog signals - Yellow 5 α Command Swivel angle command value IN nalog ±10 V Green 6 α ctual ctual swivel angle value normalized OUT nalog ±10 V Purple 7 p Command Pressure command value IN nalog V Pink 8 p ctual ctual pressure value normalized OUT nalog V 1) Red n.c. ctual pressure value H ctual pressure value L Function dependent on type of electronics and additional function, see below ctual pressure value input: Signal level dependent on feature 14 in the type code. Reserved for type F ( V) Brown IN nalog Black - nalog Blue Gray Supply line 10 x 0.14 mm ² shielded (shield has to be connected to the control on one end!) Functions at pin 9 Pin dditional functions Functions dependent on feature 12 of the ordering code (see page 4) X2: Connection of pressure transducer HM 16 (mating connector M12) Signal direction Signal type -.. Changing over to another oil volume matching (switch TD) IN Logic 24 V -..B Power limitation active OUT Logic 24 V 9 -..C Command value power limitation IN nalog V -..D Switch off pressure controller IN Logic 24 V 1) When using a pressure transducer with raised zero point (e.g m) a voltage of V is emitted in the case of a cable break. Pin Signal HM 16 Pin 1 OUT, +U B 2 n.c. 3 Reference L0 4 IN, analog, 0.5 to 5 V DC 5 n.c. Top view mating connector

15 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 15/32 Electrical connection: SYDFEC...2X X1: Central connection Mating connector according to EN (12-pin), for ordering code, see section accessories on page Pinout of connector or mating connector and cable set Pin Signal Description Signal direction Signal type Pinout in the cable set (accessories) 1 +U B Voltage supply IN 24 V DC 1 Supply 2 0 V = L0 Reference potential for voltage supply - 2 line 3 x PE Earth Earthing connection for the electronics - Green / yellow 1.0 mm ² 3 Fault Signals faults, e.g. cable break of command/actual value cables,, controller monitoring (logic 0 = error) OUT Logic 24 V White 4 M0 Reference potential for analog signals - Yellow nalog input I2 5 I2 Standard: Swivel angle command value nalog output 6 U OUT2 Standard: Swivel angle actual value normalized IN nalog ±10 V Green OUT nalog ±10 V Purple 11 n.c. ctual pressure value L nalog input I1 7 I1 IN nalog V Pink Standard: Pressure command value nalog output 8 U OUT1 OUT nalog ±10 V Red Standard: ctual pressure value normalized 9 DI1 Digital input DI1 IN Logic 24 V Brown ctual pressure value H ctual pressure value input: Signal level 10 IN nalog Black dependent on feature 14 in the type code. - nalog Blue Gray Supply line 10 x 0.14 mm ² shielded (shield has to be connected to the control at one side!) X2: Connection of pressure transducer HM 16 and serial interface RS232 (mating connector M12) Pin Signal HM 16 Pin Signal RS232 1 OUT, +U B 2 RxD 3 Reference L0 4 IN, analog, 0.5 to 5 V DC 5 TxD Top view mating connector X3: Connection of CN bus and digital input 2 (DI2) (connector M12) Pin Signal input Pin Signal CN 1 n.c. 3 CN GND 2 IN, digital IN2 (DI2) 4 CN-HIGH 5 CN-LOW Top view connector

16 16/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Electrical connection: SYDFEn...2X X1: Central connection Mating connector according to EN (12-pin), ordering code, see section accessories on page Pinout of connector or mating connector and cable set Pin Signal Description Signal direction Signal type Pinout in the cable set (accessories) 1 +U B Voltage supply IN 24 V DC 1 Supply 2 0 V = L0 Reference potential for voltage supply - 2 line 3 x PE Earth Earthing connection for the electronics - Green / yellow 1.0 mm ² 3 Faults Signals faults, e.g. cable break of command/actual value cables, controller monitoring (logic 0 = error) OUT Logic 24 V White 4 M0 Reference potential for analog signals - Yellow nalog input I2 5 I2 Standard: Swivel angle command value nalog output 6 U OUT2 Standard: Swivel angle actual value normalized nalog input I1 7 I1 Standard: Pressure command value nalog output 8 U OUT1 Standard: Speed command value 11 n.c. ctual pressure value L Digital input DI1 9 DI1 Standard: Synchronization bit DI1 ctual pressure value H ctual pressure value input: Signal level 10 dependent on feature 14 in the type code. IN nalog ±10 V Green OUT nalog ±10V Purple IN nalog V Pink OUT nalog ±10 V Red IN Logic 24 V Brown IN nalog Black - nalog Blue Gray Supply line 10 x 0.14 mm ² shielded (shield has to be connected to the control on one end!) X2: Serial interface RS232 and a switchable digital input S1 / pressure transducer input for HM 16 (mating connector M12) Pin Signal input Pin Signal RS232 1 OUT, +U B 2 RxD 3 Reference L0 4 nalog input V for HM 16 Digital input 0 V low, 10 V high (max. 12 V) Standard: Speed variable operation on, S1 5 TxD Top view mating connector X3: CN bus and digital input 2 (connector M12) Pin Signal input Pin Signal CN 1 n.c. 3 CN GND 2 IN, digital IN2 (DI2) 4 CN-HIGH Standard: Start teach-in, S2 5 CN-LOW Top view connector

17 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 17/32 Closed control loop quality Notes: The values indicated are only valid when using the components listed in this data sheet and belonging to the system. t pressures < 20 bar, you have to take into account higher tolerances due to the lower actuating forces. Swivel angle control Pressure control 1) Linearity tolerance 1.0 % 1.5 % ( 1.0 % 2 ) Thermal error 0.5 % / 10 K 0.5 % / 10 K Hysteresis 0.2 % 0.2 % Repeatability 0.2 % 0.2 % 1) without taking into consideration pump pulsation 2) For SYDFEC and SYDFEn using the integrated calibration function Transition function for pressure command value step-change, SYDFE with 360 spool (design ) The curve shapes and control times indicated are only reached with optimized pressure controller p Command 120 Pressure p [bar] p ctual Pressure p [bar] p Command p ctual T 95% Control time T 95% Control time T 95% in ms for a connected hydraulic fluid volume (lines and actuator) Hydraulic fluid volume T 95% < 5 l 150 ms 5 10 l 200 ms l 250 ms For pressures up to 40 bar the values of the response times are higher.

18 18/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Transition function for swivel angle command value step-change with 360 spool (design ) Size 18, 28, 45, 71 p = 20 bar Swivel angle actual value [%] Time [ms] Swivel angle actual value [%] Time [ms] Size 18, 28, 45, 71 p = 50 bar Swivel angle actual value [%] Time [ms] Swivel angle actual value in [%] Time [ms] Size 100 p = 50 bar Swivel angle actual value [%] Size 140 p = 50 bar Swivel angle actual value in % Time [ms] Time [ms] Swivel angle actual value [%] Swivel angle actual value in % Time [ms] Time [ms]

19 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 19/32 Unit dimensions: SYDFE1 (dimensions in mm) The unit dimensions of the base pump (axial piston pump 10VSO) are contained in the data sheets RE (size 28 to 140) and RE (size 18). Size 18 to 140 (Shaft variant S ; without through-drive N00 ) Preload valve (optional) Pilot valve attachment for clockwise direction of rotation 1 6 I 6 II B III (Shown: size 71) S Pilot valve attachment for counter-clockwise direction of rotation 3 7 II 7 I 15 Z Space required to remove the mating connector Pilot oil port Z Size I 6 II 7 I 7 II 7III

20 20/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Unit dimensions: SYDFEE, SYDFEC and SYDFEn (dimensions in mm) The unit dimensions of the base pump (axial piston pump 10VSO) are contained in the data sheets RE (size 28 to 140) and RE (size 18). Size 18 to 140 (Valve mounting direction 0 ; shaft variant S ; without through-drive N00 ) Space required for removing the mating connector Preload valve (optional) I 6 II B III Z S 3 Connection X2 (pressure transducer HM 16) is available on SYDFEE with actual pressure value input F, as well as on SYDFEC and SYDFEn. Connection X3 (CN bus) is available on SYDFEC and SYDFEn 8 II Pilot valve attachment for direction counter-clockwise rotation 8 I Pilot valve attachment for clockwise direction of rotation Pilot oil connection Z Size I 6 II 7 8 I 8 II 8III Dimension 7 required installation space for connecting the optional pressure transducer HM 16

21 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 21/32 Unit dimensions: Combination pumps (dimensions in mm) Main pump 10VSO.../31 +10VSO.../31 (SYDFE.-2X/... +SYDFE.-2X/...) Built-on pump Main pump 10VSO 18 10VSO 28 10VSO 45 10VSO 71 10VSO VSO 140 Built-on pump 10VSO VSO , , , , VSO VSO VSO VSO

22 22/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Hubs for through-drives Hubs for the combination of single pumps or the combination of SYDFE with other pumps. Please observe that the built-on pump has a splined shaft SE J744 with the diameter indicated. The following conditions apply to built-on pumps listed in the table: SYDFE and 10VSO with shaft S or R Internal gear pump PGH with shaft R, flange U2, see RE Internal gear pump PGF3 with shaft J, flange U2, see RE External gear pump ZPF with shaft R, front cover R, see RE Please also observe that the through-drive of the main pump and the flange of the attachement pump (see order details page 2) are the same. Please check in the current data sheet of the gear pump whether the shaft ends have the dimensions indicated. Main pump SYDFE or 10VSO Built-on pump Size 18 Size 28 Size 45 Size 71 Size 100 Size 140 ø shaft Pump type (examples) R R R R R R R R R R R / (SE -B) 7/ (SE B) R R R R (SE B-B) R R R ¼ 32-4 (SE C) R R ½ 38-4 (SE C-C) R ¾ 44-4 (SE D) R R R R R / (SE ) SYDFE-2X, 10VSO..31 Size 018 shaft S SYDFE-2X, 10VSO..31 Size 028 shaft R PGF3 SYDFE-2X, 10VSO..31 Size 045 shaft R PGH4 SYDFE-2X, 10VSO..31 Size 071 shaft R SYDFE-2X, 10VSO..31 Size 100 shaft S PGH5 SYDFE-2X, 10VSO..31 Size 140 shaft S 1PF2G2, PGF2, PGH2, PGH3, ZPF

23 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 23/32 Unit dimensions: Through-drives (dimensions in mm) KD3 Flange ISO 100, 2-hole for mounting SYDFE.-2X (size 28 and size 45, flange ) 10VSO..31 (size 28 and size 45, flange, see RE 92711) Sectional view with examples of hubs (order number for hubs, see page 22) Top view Hub 7/8 Hub 1 6 ø140 ø ø B to pump mounting face to pump mounting face 1 10 Size M12; 15 right through M12; 14 right through M12; 20 deep M12; 20 deep M12; 20 deep

24 24/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Unit dimensions: Through-drives (dimensions in mm) KD5 Flange ISO hole for mounting SYDFE,-2X (size 71 and size 100. flange ) 10VSO,,31 size 71 and size 100. flange. see RE 92711) Sectional view with examples of hubs (order number for hubs, see page 22) Top view Hub 1 ¼ Hub 1 ½ Not on size 71 Not on size ø ø B to pump mounting face 1 to pump mounting face 1 Size M16; 20 right through M16; 20 deep M16; 24 deep

25 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 25/32 Unit dimensions: Through-drives (dimensions in mm) KD7 Flange ISO 180, 4-hole for mounting SYDFE.-2X (size 140, flange B) 10VSO..31 (size 140, flange B, see RE 92711) Sectional view with examples of hubs (order number for hubs, see page 22) Top view Hub 1 ¾ 158, ,4 B to pump mounting face Size M16; 22 continuous

26 26/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Unit dimensions: Through-drives (dimensions in mm) KC1 Flange SE 82-2 (SE, 2-hole) for mounting SYDFE.-2X (size 18, flange C) 10VSO..31 (size 18, flange C, see RE 92712) PGF2 (shaft J, flange U2, see RE 10213) PGH2 and PGH3 (shaft R, flange U2, see RE 10223) ZPF (shaft R, front cover R, see RE 10089) Sectional view with examples of hubs (order number for hubs, see page 22) Top view Hub 5/8 Hub 3/ , B 4 to pump mounting face 1 10 to pump mounting face Size M10; 16 deep M10; 16 deep M10; 16 deep M10; 20 deep M10; 20 deep M10; 20 deep

27 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 27/32 Unit dimensions: Through-drives (dimensions in mm) KC3 Flange SE (SE B, 2-hole) for mounting SYDFE.-2X (size 28 and size 45, flange C) 10VO..31 (size 28 and size 45, flange C, see RE 92701) PGF3 (shaft J, flange U2, see RE 10213) PGH4 (shaft R, flange U2, see RE 10223) Sectional view with examples of hubs (order number for hubs, see page 22) Top view Hub 7/8 Hub 1 Not for size Not for size 28 B to pump mounting face to pump mounting face Size M12; 15 deep M12; 18 deep M12; 20 deep M12; 20 deep M12; 20 deep

28 28/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Unit dimensions: Through-drives (dimensions in mm) KC5 Flange SE (SE C, 2-hole) for mounting SYDFE.-2X (size 71 and size 100, flange C) 10VO..31 (size 71 and size 100, flange C, see RE 92701) PGH5 (shaft R, flange U2, see RE 10223) Sectional view with examples of hubs (order number for hubs, see page 22) Top view Hub 1 ¼ Hub 1 ½ Not on size 71 Not on size B to pump mounting face to pump mounting face 1 13 Size M16; 18 deep M16; 25 deep M16; 32 deep

29 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 29/32 Unit dimensions: Through-drives (dimensions in mm) KC6 Flange SE (SE D, 4-hole) for mounting SYDFE.-2X (size 140, flange D) 10VO..31 (size 140, flange D, see RE 92701) Sectional view with examples of hubs (order number for hubs, see page 22) Top view Hub 1 ¾ B 5 to pump mounting face 1 13 Size M16; 24 deep

30 30/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Torsionally flexible couplings for the connection to a standard electric motor Motor SYDFE.-2X Frame size/ Code number Shaft diameter Size 18 Shaft S, 3/4 Size 28 Shaft S or R, 7/8 Size 45 Shaft S or R, 1 100/0 112/0 28 R R /0 38 R R R /0 42 R R R /0 48 R R /0 55 R R /0 60 R R /0 65 R Frame size/ Code number Motor Shaft diameter Size 71 Shaft S or R, 1 ¼ SYDFE.-2X Size 100 Shaft S, 1½ Size 140 Shaft S, 1 ¾ 160/0 42 R /0 48 R R /0 55 R R R /0 60 R R R /0 65 R R R /0 75 R R R /0 80 R ) R ) 315/1 80 R ) up to 40 C

31 RE 30030/04.09 Type SYDFE... Hydraulics Bosch Rexroth G 31/32 Project planning information lways shield command and actual value lines. The distance to the antenna lines resp. radio equipment has to be 1 m at least. Do not lay signal lines near power lines. Complementary notes on the control system SYDFE can be found in the operating instructions (see section Further information on this control system on this page). Further information on this control system Operating instructions for SY(H)DFE1 (in preparation) RE B Operating instructions for SY(H)DFEE RE B Operating instructions for SY(H)DFEE (current / planned) RE B / RE B Operating instructions for SY(H)DFEn (in preparation) RE B Data sheet for axial piston variable displacement pump 10VSO../31 RE / RE Data sheet for amplifier VT X for SYDFE1 RE Data sheet for pilot valve VT-DFP.-2X RE Data sheet for pump preload valve SYDZ X RE Data sheet for swivel angle sensor VT-SW-1-1X RE Data sheet for pressure transducer HM 12-1X and HM 13-1X RE Data sheet for pressure transducer HM 16-1X RE Data sheet for pressure transducer HM 17-1X RE Operating instructions for test device VT-PDFE RE B Current information can also be found on the internet at (English) or (German).

32 32/32 Bosch Rexroth G Hydraulics Type SYDFE... RE 30030/04.09 Bosch Rexroth G Hydraulics Zum Eisengießer Lohr am Main, Germany Phone +49 (0) / 18-0 Fax +49 (0) / documentation@boschrexroth.de This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth G. It may not be reproduced or given to third parties without its consent. The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging.