Nucor VR16 II TM Vertical Rib Standing Seam Roof System
|
|
- Garey Spencer Cox
- 8 years ago
- Views:
Transcription
1 Nucor VR16 II TM Vertical Rib Standing Seam Ro System
2
3 Nucor VR16 II Vertical Rib Standing Seam Ro Perfect for the Marketplace The Nucor Building Systems VR16 II Ro Panel is a Structural Standing Seam Vertical Rib Panel that is perfect for architectural requirements in today s marketplace. Nucor VR16 II Ro System panel is a weathertight system that is an ideal solution for buildings with hips and valleys, and easily accommodates complex ro geometries. The VR16 II ro panel fers an attractive architectural ro system available both in Galvalume and PVDF finishes as standard. Panels are installed with concealed fastener clips allowing for thermal movement, and mechanically seamed for weather tightness. Nucor VR16 II Warranties 25 Year Galvalume Finish 35 Year PVDF Paint Finish 20 Year Weathertightness For specific details, please refer to the Warranty Guide at Galvalume is a registered trademark BIEC International, Inc.
4 Performance and Testing AISI Gravity & Uplift Base Testing ASTM E108 Test Methods for Fire Tests Ro Coverings ASTM E283 Test Method for Determining Air Leakage through Wall Systems ASTM E1592 Test Method for Wind Uplift Performance Sheet Metal Roing Systems ASTM E1646 Test Method for Water Penetration Exterior Ro Systems ASTM E1680 Test Method for Rate Air Leakage through Exterior Ro Systems FM Simulated Hail Damage Testing Class SH Hail Resistance US Army Corps Engineers Approved per CEGS test specification Panel Ratings Gauge Secondary Spacing Seam Option Factory Mutual Purlins or Joists 5'-0" Nucor Vise Lock 360 Factory Mutual Purlins or Joists 3'-4" Nucor Vise Lock 360 Factory Mutual Purlins or Joists 2'-6" Nucor Vise Lock 360 Factory Mutual Purlins or Joists Varies Nucor Vise Lock 360 UL90 24 Purlins or Joists 5'-0" Nucor Vise Lock /Vise Lock 360 Florida Approval 24 Purlins or Joists 5'-0" Nucor Vise Lock /Vise Lock 360 Miami Dade 22 Purlins or Joists 5'-0" Nucor Vise Lock /Vise Lock 360
5 Product Specifications & Details VR16 II Panel Options Rib height: 2 Cover width: 16 Galvalume finish Factory sealant continuously applied along female rib Minor striations to help reduce oil canning Painted PVDF finishes Standard 24 gauge material (22 gauge also available) Mechanically seamed for weathertight installation Panel installed with concealed fastener clips that allow for thermal movement 1/4:12 Minimum ro slope required Standard Optional VR16 II Seaming Options Nucor Vise Lock tmseam "VISE LOCK" SEAM Nucor Vise Lock 360 tmseam "VISE LOCK 360" SEAM
6 Panel Properties Designated Gage Steel Steel Yield KSI Engineering Properties Nucor Building Systems 16" Nucor Vise Lock Seam Panel Base Metal Thick.(In) Total Thick. (In) Panel Weight (lbs/ ft 2 ) Ix (In 4 / ft) Top In Compression Sx (In 3 / ft) Bottom In Compression 1. Panels are checked for bending (B), shear (S), combined bending and shear(b+s), and deflection (D). The controlling check is noted in the table. Deflection was limited to span/ Section Properties have been calculated in accordance with the 2007 North American Specification for the Design Cold-Formed Steel Structural Members. 3. Minimum yield strength 24 and 22 gage steel is 50,000 psi. 4. Steel panels are either aluminum-zinc alloy or G-90 coated. The base metal thickness was used in determining section properties. 5. Positive load (POS) is applied inward toward the panel supports and is applied to the outer surface the full panel cross-section. Ma K-IN Ix (In 4 / ft) Sx In 3 / ft) 24 Ga Ga Gage Panel 24 Ga. 22 Ga. Designated Gage Steel Steel Yield KSI No. Spans Load Type Maximum Total Uniform Load in PSF Span Lengths, Ft Ma K-IN Fb KSI POS POS POS POS POS POS POS POS Engineering Properties Nucor Building Systems 16" Nucor Vise Lock 360 Seam Panel Base Metal Thick. (In) Total Thick. (In) Panel Weight (lbs/ ft 2 ) Ix (In 4 / ft) Top In Compression Sx (In 3 / ft) Ma K-IN Ix (In 4 / ft) Bottom In Compression Sx In 3 / ft) 24 Ga Ga Gage Panel 24 Ga. 22 Ga. No. Spans Load Type Maximum Total Uniform Load in PSF Span Lengths, Ft. Ma K-IN Fb KSI POS POS POS POS POS POS POS POS
7
8 With four full-service plants and a sales fice strategically located throughout the country, Nucor Building Systems has the capacity to meet your needs. INDIANA PLANT 305 Industrial Parkway Waterloo, IN Ph: Fax: NE SALES OFFICE 201 Granite Drive Suite 280 Lancaster, PA Ph: Fax: SOUTH CAROLINA PLANT P. O. Box Whetstone Rd. Swansea, SC Ph: Fax: TEXAS PLANT 600 Apache Trail Terrell, TX Ph: Fax: UTAH PLANT P. O. Box North Watery Lane Brigham City, UT Ph: Fax: NBS10981
METAL BUILDING SYSTEMS
BUILDING SYSTEMS The Brand of Choice METAL BUILDING SYSTEMS www.nucorbuildingsystems.com Building Systems The Brand of Choice Nucor Building Systems, a division of Nucor Corporation, is one of the most
More informationPRODUCT SPECIFICATIONS
LokSeam LokSeam 12" One of the most versatile architectural metal panels available today, LokSeam by ABC, is a snap-together, concealed fastener, standing seam roof system with a 13/4" tall vertical rib,
More informationStanding Seam Roof Systems
Standing Seam Roof Systems REAL PEOPLE. REAL PRODUCTS. REAL SOLUTIONS. www.a-s.com Building Benefits You Can Expect From A&S Materials Standing Seam roof panels weigh a relatively modest 11/2 pounds per
More informationSECTION 07400 STANDING SEAM METAL ROOF
SECTION 07400 STANDING SEAM METAL ROOF PART 1 - GENERAL 1.01 SECTION INCLUDES A. Work described in this section includes pre-formed standing seam metal roofing system complete with clips, perimeter and
More informationCHAPTER 7: Building Systems ROOFING SYSTEMS
ROOFING SYSTEMS Purpose Examples 1. Shingle roof system 2. Metal roof with blanket insulation 3. Metal roof with rigid insulation 4. Built-up asphalt roof system 5. Single-ply roof system 6. Modified Bitumen
More informationVERTICAL LOCK Table of Contents
Table of Contents TABLE OF CONTENTS Vertical Lock Product Data Sheet... 2 Vertical Lock Engineering Data... 3 General Information... 6 Material Testing... 7 Panel Overview... 8 Handling Material & Storage
More informationTABLE OF CONTENTS" SECTION 3: Comparing Standing Seam Metal to Other Metal Roofs PAGE 7"
2 TABLE OF CONTENTS SECTION 1: What is a Standing Seam Metal Roof PAGE 3 SECTION 2: Common Types of Standing Seam Metal Roofs..PAGE 5 SECTION 3: Comparing Standing Seam Metal to Other Metal Roofs PAGE
More informationMIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
MIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786) 315-2590
More informationDENVER MODEL 30 X 30 SPECIFICATIONS
DENVER MODEL 30 X 30 SPECIFICATIONS Dimensions: Roof Dimensions 30-0 x 30-0 (4) Columns (Center to Center) 25-6½ x 25-6½ Minimum Clearance 8-0 Roof Height @ Peak Dependent on Col. Ht. Hip Roof 4:12 pitch
More informationstand the tests of time, & economics
Roofs that stand the tests of time, THE elements & economics Architectural metal systems WHY METAL ROOFING? AMS metal standing seam roofs provide the longest life cycle of any common roof in use today,
More informationSECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK
SECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK A. This section covers the pre-finished, pre-fabricated Architectural standing seam roof system. All metal trim,
More informationmetal Duil~ing manufacturers Association
metal Duil~ing manufacturers Association ApplicatiDns metal Building Systems Conventional Buildings Retrofit Roofing Projects l~e Perfect Cover.One of the most important technological advances in building
More informationPERFORMANCE TEST REPORT. Rendered to: ARCHITECTURAL METAL SOLUTIONS, INC.
PERFORMANCE TEST REPORT Rendered to: ARCHITECTURAL METAL SOLUTIONS, INC. SERIES/MODEL: AMS ARMOR-LOCK PRODUCT TYPE: STANDING SEAM METAL ROOF PANEL SYSTEM Report No: 97123.02-901-44 Test Date: 05/17/10
More informationGUIDELINE SPECIFICATIONS
GUIDELINE SPECIFICATIONS GORDON SOFFIT-SHIELD - An Exterior Metal Soffit System DIVISION 05 5800 or DIVISION 07 7700 Note To Specifier: SOFFIT-SHIELD should be installed by tradesmen that are experienced
More informationDIVISION: 07 00 00 THERMAL AND MOISTURE PROTECTION SECTION: 07 41 13 METAL ROOF PANELS REPORT HOLDER: FIRESTONE BUILDING PRODUCTS COMPANY, LLC
0 ICC ES Report ICC ES (800) 423 687 (62) 699 043 www.icc es.org 000 Most Widely Accepted and Trusted ESR 3422 Reissued 09/201 This report is subject to renewal 09/2016. DIVISION: 07 00 00 THERMAL AND
More informationTABLE OF CONTENTS. Roof Decks 172 B, BA, BV Deck N, NA Deck. Form Decks 174.6 FD,.6 FDV Deck 1.0 FD, 1.0 FDV Deck 1.5 FD Deck 2.0 FD Deck 3.
Pages identified with the NMBS Logo as shown above, have been produced by NMBS to assist specifiers and consumers in the application of New Millennium Building Systems Deck products. Pages identified with
More informationThe Butler MR-24 Standing Seam Roof Difference. A comparison between metal roof systems
The Butler MR-24 Standing Seam Roof Difference A comparison between metal roof systems Roof Systems Necessities Weathertight (don t leak!) Low maintenance Weathertightness Roof clips, seams, panel alignment
More informationCF-Mesa, CF-Light Mesa, CF-Flute, CF-Metl-Plank, CF-Striated, CF-Santa Fe, CF-Architectural Flat, CF...
Building Insulations - Walls and Ceilings (FM Approval Numbers 4411, 4651, 4880, 4881, 4882) Insulating materials may occur in building construction to reduce heat or sound transmission through a wall,
More informationSECTION 07720 PREFORMED METAL STANDING SEAM ROOFING
SECTION 07720 PREFORMED METAL STANDING SEAM ROOFING PART ONE GENERAL DESCRIPTION This section includes pre-formed standing seam metal roofing and related flashings, closures, trim and accessories including,
More informationCOLORADO MODEL. 35 x 65 SPECIFICATIONS
COLORADO MODEL 35 x 65 SPECIFICATIONS Dimensions: Roof Dimensions 35-0 x 65-0 Column Dimensions (center to center) 31-0 x 30-6 Minimum Clearance 14-0 Roof Height @ Peak ±18-8 Curved Roof ±42-6 radius Square
More informationSTANDARD PROCEDURES FOR INSTALLATION OF METAL ROOF SYSTEMS
ROOFING APPLICATION STANDARD (RAS) No. 133 STANDARD PROCEDURES FOR INSTALLATION OF METAL ROOF SYSTEMS 1. Scope 1.1 This application standard has been developed to provide consistent information for the
More informationDIVISION 07. Architectural Sheet Metal. Weathertight Warranties. Rollforming Equipment. 50+ Years of SSMR, Installation & Technical Experience
DIVISION 07 Engineered Metal Roofing Systems Architectural Sheet Metal Specialty Coil & Sheet Products Weathertight Warranties Rollforming Equipment Accessories & Components 50+ Years of SSMR, Installation
More informationABSeam Panel Overview and Installation Instructions
82 Garden Spot Road Ephrata, PA 17522 717-445-6885 35 Ridge Road Newville, PA 17241 717-776-5951 ABSeam Panel Overview and Installation Instructions Applications: The ABSeam panel is an architectural panel
More information238T Standing Seam Metal Roof System (SSMRS)
238T Standing Seam Metal Roof System (SSMRS) Text in red are instructions to the specifier and should be deleted. Text in blue are choices that need to be made, with those not selected, deleted. McElroy
More informationDrexel Metals Inc. DMC 100SS 16oz min. Copper Mechanical Seam Metal Roof System over Plywood
Drexel Metals Inc. DMC 100SS 16oz min. Copper Mechanical Seam Metal Roof System over Plywood Section 07411 Metal Roof Panels Part 1 General 1.1 Summary A. This section includes the following: a. Factory-formed
More informationTechnical Installation Information
Technical Installation Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE ULTRA-DEK ROOFING SYSTEM. ALWAYS INSPECT EACH AND EVERY PANEL AND ALL ACCESSORIES
More informationSECTION 07 42 13 METAL WALL PANELS
Mitsubishi Plastics Composites America, Inc. 401 Volvo Parkway Chesapeake, VA 23320 Phone: (800) 422-7270 Fax: (757) 436-1896 E-mail: info@alpolic.com www.alpolic-northamerica.com This MANU-SPEC utilizes
More informationDouble-Lok. Technical/Installation Information
Double-Lok Technical/Installation Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE DOUBLE-LOK ROOFING SYSTEM. MBCI DETAILS MUST BE FOLLOWED AS A MINIMUM
More informationMETAL ROOF & WALL SYSTEMS
07 40 00/MCE BuyLine 3423 CATALOG 2006 METAL ROOF & WALL SYSTEMS ARCHITECTURAL COMMERCIAL RESIDENTIAL Since 1963, McElroy Metal has served the construction industry with quality products and excellent
More informationINNOVATIVE. ADAPTABLE. ENERGY EFFICIENT.
INNOVATIVE. ADAPTABLE. ENERGY EFFICIENT. awipanels.com From freezing, sub-zero temperatures to Contents dry heat or high humidity, Mother Nature continually tests the limits of building envelopes. That's
More informationCENTRIA SRS3 Structural Standing Seam Metal Roof Panels
CENTRIA SRS3 Structural Standing Seam Metal Roof Panels CENTRIA SRS3 Structural Standing Seam Metal Roof Panels are manufactured in many different coil coating systems and painted with a wide variety of
More informationQuality Metal Roofing Products
The Long Term Solution Quality Metal Roofing Products Here at Metal Roofing Wholesalers you will find a large selection of the highest quality metal roofing products available on todays market. We Ship
More informationA. Double lock standing seam, single element, metal roof panels.
Specifiers: Click on the icon in the WORD toolbar to reveal detailed instructions SECTION 07 41 13 METAL ROOF PANELS Morin Metal Panels Double Lock Standing Seam Metal Roof Panels PART 1 - GENERAL 1.1
More informationSTRUCTURAL STANDING SEAM ROOF SYSTEMS
STRUCTURAL STANDING SEAM ROOF SYSTEMS S R S Design M A N U A L R INTRODUCTION INTRODUCTION The System...1 Panels...2 SRS 2 and SRS 3 Basic Differences...3 Curving...4 Accessories...5-9 Fasteners...10 Sealants...11
More informationSpecifications. Preformed Metal Wall and Roof Panels. Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023
Specifications Preformed Metal Wall and Roof Panels Alcoa Cladding Systems Manufacturing Plant 100 Industrial Boulevard Eastman, Georgia 31023 Section 07410 Preformed Metal Wall and Roof Panels Structural
More informationmetals LLC Metal roofing ON-DEMAND
Metal roofing ON-DEMAND PRODUCT CATALOG About Drexel Metals contents Metal Roofing on Demand PAGES 4-5 Certified Installer Program & Warranties PAGES 6-7 Engineered Metal Roof Systems PAGES 9-15 Solar
More informationLokSeam. Design/Installation Information. This booklet includes: Trims and Accessories Design and Installation Information
LokSeam Design/Installation Information This booklet includes: Trims and Accessories Design and Installation Information Since 1908 ABC has developed a strong reputation by providing top quality reliable
More informationAIA PRESENTATION. Standing Seam Metal Roofing Seminar SSRLU2B 1 LU/HSW Hour
AIA PRESENTATION Standing Seam Metal Roofing Seminar SSRLU2B 1 LU/HSW Hour Best Practice MBCI is a Registered Provider with the American Institute of Architects Continuing Education Systems. Credit earned
More informationDuPont Tyvek Commercial Air Barrier Assemblies Exceed Air Barrier Association of America, ASHRAE 90.1
Building Science Bulletin DuPont Tyvek Commercial Air Barrier Assemblies Exceed Air Barrier Association of America, ASHRAE 90.1 and IECC Air Leakage Requirements When Tested in Accordance with ASTM E2357
More informationSlim Seam Architectural Design Manual
Slim Seam Architectural Design Manual Headquarters: 3449 Hempland Road Lancaster, PA 17601 Phone: 800-477-2741 Fax: 800-283-4289 Architectural Products Division: 308 Alabama Blvd. Jackson, GA 30233 Phone:
More informationTECHNICAL NOTE. Design of Diagonal Strap Bracing Lateral Force Resisting Systems for the 2006 IBC. On Cold-Formed Steel Construction INTRODUCTION
TECHNICAL NOTE On Cold-Formed Steel Construction 1201 15th Street, NW, Suite 320 W ashington, DC 20005 (202) 785-2022 $5.00 Design of Diagonal Strap Bracing Lateral Force Resisting Systems for the 2006
More informationHoliday Inn Express & Suites Covington (Newton County) 1. Standing-seam metal roofing, custom fabricated.
PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standing-seam metal roofing, custom fabricated. 1.2 SUBMITTALS A. Product Data: For each type of product indicated. B. Shop Drawings: Show installation
More informationTremLock Metal Roofing and Wall Solutions
TremLock Metal Roofing and Wall Solutions ROOFING & BUILDING MAINTENANCE TABLE OF CONTENTS PRODUCT systems overview APPLICATION TremLock Roofing and Wall Solutions...4 STANDING SEAM TremLock T-238 Roof,
More informationSECTION 07 61 13 STANDING SEAM METAL ROOFING
SECTION 07 61 13 STANDING SEAM METAL ROOFING PART 1 GENERAL 1.01 SCOPE OF WORK A. The Work shall include all labor, materials, equipment and supervision required to complete the work of the above referenced
More informationTechnical Installation Information
Technical Installation Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE Double-Lok ROOFING SYSTEM. ALWAYS INSPECT EACH AND EVERY PANEL AND ALL ACCESSORIES
More informationIinterviewed with a school district
Iinterviewed with a school district several years ago for an open-end contract for roof consulting services. At the conclusion of our typical presentation, one of the board members asked my opinion of
More informationInstallation Manual for STANDING SEAM ROOFING
Installation Manual for STANDING SEAM ROOFING Absolute Steel Toll Free 877-833-3237 / Phone 480-768-1618 / Fax 480-768-1514 www.metalroofingsource.com Standing Seam features approximately one-inch high
More informationSECTION 07410 METAL ROOF & WALL PANELS
This document specifies Metal Roofing Systems prefinished factory formed metal roofing marketed as MRS System 2500 steel and aluminum roofing systems and includes MRS flashing and Trim. MRS finish is a
More informationSTANDING SEAM METAL ROOFING DETAILS PDF
STANDING SEAM METAL ROOFING DETAILS PDF ==> Download: STANDING SEAM METAL ROOFING DETAILS PDF STANDING SEAM METAL ROOFING DETAILS PDF - Are you searching for Standing Seam Metal Roofing Details Books?
More informationCity of San Diego, CWP Guidelines
PART 1 -- GENERAL SECTION 08520-1.1 WORK OF THIS SECTION City of San Diego, CWP Guidelines A. The WORK of this Section includes providing aluminum windows with frames, bracing, glazing attachments, screens,
More informationATLANTA MODEL SPECIFICATIONS
ATLANTA MODEL 50 SPECIFICATIONS Dimensions: Roof Dimensions (point to point) 50-0 Column Dimensions (out to out of columns) 44-0 Eave Height 8-0 Roof Height @ Peak ±21-8⅞ Hip Roof 6:12 pitch Square Feet
More informationSECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS. System 402 Flush-Glazed Screw Spline Storefront
PART 1 GENERAL 1.01 Work Included SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS System 402 Flush-Glazed Screw Spline Storefront A. Furnish and install aluminum architectural storefront system
More informationPART 1 GENERAL 1.1 SECTION INCLUDES
J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including
More information- - - - Steel Panel Frame. Exterior Steel Sheeting. Optional Rigid Insulation. Optional Steel Insulation Liner
The Kelly Klosure pre-framed modular panel has 4 components that are factory finished to create an easy and versatile bolt-together system in the field. Steel Panel Frame Exterior Steel Sheeting Optional
More informationDiscipline: Structural Issued 04-26-06
California Department of General Services. Division of the State Architect. Product Acceptance Report STRUCTURAL SHEAR PANEL SURE-BOARD SERIES 200 PANELS PA-132 Discipline: Structural Issued 04-26-06 This
More informationHow To Design A Post Tensioned Deck For A Building
SAMUEL ÁVILA STRUCTURAL OPTION FACULTY CONSULTANT: THOMAS BOOTHBY UNIVERSITY OF CENTRAL FLORIDA S ACADEMIC VILLAGES ORLANDO, FL THESIS PROPOSAL EXECUTIVE SUMMARY DECEMBER 12, 2005 Introduction: The University
More informationSTAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM
STAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM Installed in Pre-engineered Steel Buildings Provides Lowest Cost Construction Method for CORROSIVE AND WET Environments PREFERRED SOLUTIONS, INC.
More informationPERFORMANCE TEST REPORT. Rendered to: BAMCO INC. PRODUCT TYPE: ACM Wall Panel Systems
PERFORMANCE TEST REPORT Rendered to: BAMCO INC. PRODUCT TYPE: ACM Wall Panel Systems Summary of Results Title Test Specimen #1 Test Specimen #2 Air Infiltration
More informationMetal Roof Systems in High-Wind Regions
Metal Roof Systems in High-Wind Regions http://www.fema.gov HURRICANE IKE RECOVERY ADVISORY Purpose: To recommend practices for designing and installing metal roof systems that will enhance wind resistance
More informationMOCK-UP TEST REPORT. Rendered to: TUBELITE, INC. PROJECT: 200 Series Curtain Wall Mock-Up
MOCK-UP TEST REPORT Rendered to: TUBELITE, INC. PROJECT: 200 Series Curtain Wall Mock-Up Report No: 85616.01-120-32 Test Completion Date: 01/15/09 Report Date: 02/11/09 Record Retention End Date: 01/15/13
More informationSTANDING SEAM METAL ROOFING PANELS
STANDING SEAM METAL ROOFING PANELS Roof it for the last time. ENERGY EFFICIENCY WITH STYLE & DURABILITY METAL ROOFING FOR RESIDENTIAL AND COMMERCIAL APPLICATIONS. Featuring the TITAN Cool Roof Reflective
More informationPreformed Metal Roofing and Siding
Page -1-1. GENERAL 1.1. Description This specification along with the drawings covers the furnishing of all material, products, equipment, accessories, tools, services, transportation, labor and supervision
More informationChapter 6 ROOF-CEILING SYSTEMS
Chapter 6 ROOF-CEILING SYSTEMS Woodframe roof-ceiling systems are the focus of this chapter. Cold-formed steel framing for a roof-ceiling system also is permitted by the IRC but will not be discussed;
More informationTable of Contents. Western States Standing Seam SS675 Panel Installation, Flashings & Shop Drawing Detail Guide. Notes to Designer /Installers..
Western States Standing Seam SS675 Panel Installation, Flashings & Shop Drawing Detail Guide Table of Contents Section Page Section Page Notes to Designer /Installers.. 1 Fastener Placement and Selection.2-3
More informationSECTION 07411 PREFORMED METAL ROOF PANELS
SECTION 07411 PREFORMED METAL ROOF PANELS PART 1 GENERAL 1.01 SECTION INCLUDES A. Roofing system of preformed aluminum panels. B. Fastening system. C. Underlayment. D. Accessories and miscellaneous components.
More informationAssessing Curtain Walls
Assessing Curtain Walls Considerations and Best Practices Paul E Beers GCI Consultants, LLC pbeers@gciconsultants.com What is a Curtain Wall System? A curtain wall system is an outer covering of a building
More informationDesigner Series. Technical/Product Information
Designer Series Technical/Product Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE WALL SYSTEM. MBCI DETAILS MUST BE FOLLOWED AS A MINIMUM TO INSURE APPROPRIATE
More informationSTRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM
Chapter 9 STRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM 9.1 BACKGROUND Steel is widely used in the construction of multi-storey buildings. However, steel construction is seldom used and is traditionally
More informationPERFORMANCE TEST REPORT. Rendered to: UNITED STATES ALUMINUM CORPORATION. SERIES/MODEL: 450 Center Glaze PRODUCT TYPE: Aluminum Curtain Wall
Architectural Testing PERFORMANCE TEST REPORT Rendered to: UNITED STATES ALUMINUM CORPORATION SERIES/MODEL: 450 Center Glaze PRODUCT TYPE: Aluminum Curtain Wall Title Summary of Results Air Infiltration
More informationCB-100 CB-150 CS-100 SL-100 SL-150 SLZ-1000
CB-100 CB-150 CS-100 SL-100 SL-150 SLZ-1000 Details and Installation Guide October 2013 All information, descriptions and dimensions in this manual are current at the time of printing. As always, Custom-Bilt
More informationASTM E 1886 and ASTM E 1996 TEST REPORT. Rendered to: NORSE, INC.
Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Rendered to: NORSE, INC. SERIES/MODEL: Flush Mount/Surface Mount PRODUCT TYPE: Hurricane Shutter Fastening System This report contains in its
More informationResidential Metal Roofing
Residential Metal Roofing American Since 1908 It s no secret; many consider their home to be their most valuable asset. That is why it is ever so important to protect your investment with products that
More informationTEST REPORT. Report No.: A9814.01 109 44. Rendered to: BAMCO INC. Middlesex, New Jersey. PRODUCT TYPE: Wall Cladding System SERIES/MODEL: Dry Concept
Architectural Testing TEST REPORT Report No.: A9814.01 109 44 Rendered to: BAMCO INC. Middlesex, New Jersey PRODUCT TYPE: Wall Cladding System SERIES/MODEL: Dry Concept AAMA 508 07, Voluntary Test Method
More information0845 0098 980 www.nicholsonsts.com
0845 0098 980 www.nicholsonsts.com ROOFTRAK The IFP is revolutionising the way we fix things to roofs. Technical Director of a leading UK roofing system manufacturer The ROOFTRAK-IFP A revolutionary solution
More informationMechanically Seamed Roof System Design / Installation Information
EM Mechanically Seamed Roof System Design / Installation Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE CURVED BATTENLOK ROOFING SYSTEM. ALWAYS INSPECT
More informationInstallation Detailed installation instructions are provided which should be strictly followed.
Specification System 6 The Metal Technology Thermally-Broken Vertical Slide Window has been designed in such a way that its'attractive and clean lines will enhance all types of residential and commercial
More informationJANUARY, 2016 TR-7100 Windows (Fixed) 1 EC 97909-071 085113 ALUMINUM WINDOWS Guide Specs
JANUARY, 2016 TR-7100 Windows (Fixed) 1 EC 97909-071 085113 ALUMINUM WINDOWS Guide Specs SECTION 085113 ALUMINUM WINDOWS This suggested guide specification has been developed using the current edition
More informationDiscount Direct Metal Roofing Plus Rib Roofing Panels Installation Instructions
Discount Direct Metal Roofing Plus Rib Roofing Panels Installation Instructions All questions and concerns please call 904-696-9700 Discount Direct Metal Roofing Plus Rib metal roofing panels are a strong,
More informationPRO-PANEL II. Panel Information. Detail Conditions. Flashing Profiles. Notes. Accessory Profiles. Testing Information
Table of ontents Product Page No. Product Page No. Panel Information Profile... PPP-2 Panel Overview... PPP-2 Flashing Profiles Eave (Direct Fasten)... PPP-3 leat... PPP-3 Box Gutter... PPP-3 Box Gutter
More informationSection 5A: Guide to Designing with AAC
Section 5A: Guide to Designing with AAC 5A.1 Introduction... 3 5A.3 Hebel Reinforced AAC Panels... 4 5A.4 Hebel AAC Panel Design Properties... 6 5A.5 Hebel AAC Floor and Roof Panel Spans... 6 5A.6 Deflection...
More informationResidential Roofing Guide
Residential Roofing Guide TABLE OF CONTENTS Building Detail and Accessories...... 1 Panel Introduction and Handling...... 2 Cutting and Trimming.... 3 Roof Preparation..... 3 Roof Slope..... 3 Re-roofing...
More informationTechPractices: Home Front Homes:
TechPractices: Home Front Homes: PATH's Technologies in Practice are large scale housing projects throughout the U.S. where innovative technologies are being installed and used. Information is presented
More informationVersa-Span STRUCTURAL STANDING SEAM
Versa-Span STRUCTURAL STANDING SEAM Features and Benifits 18" Standard Panel Width 1 3/4" Snap Lock Seam Custom Lengths 2' 0" to 300' 0" Concealed Clip System-No Seaming Required Minimum Slope 2 : 12 UL
More informationImpact-Resistant Windows and Sliding Glass Doors
Impact-Resistant Windows and Sliding Glass Doors Make Your Home A SafeHarbor. SafeHarbor Impact-Resistant Windows and Sliding Glass Doors are designed to look like traditional windows and doors, but they
More informationSECTION 07 41 13.16 - STANDING-SEAM METAL ROOF PANELS PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 07 41 13.16 - STANDING-SEAM METAL ROOF PANELS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationHURRICANE MITIGATION RETROFITS FOR EXISTING SITE-BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES
HURRICANE MITIGATION RETROFITS FOR EXISTING SITE-BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES 101 Retrofits Required. Pursuant to Section 553.844 553.884, Florida Statutes, strengthening of existing site-built,
More informationUL 580 TEST REPORT. Rendered to: ARMSTRONG WORLD INDUSTRIES. SERIES/MODEL: MW Vector PRODUCT TYPE: Ceiling System, 3' OC
UL 580 TEST REPORT Rendered to: ARMSTRONG WORLD INDUSTRIES SERIES/MODEL: MW Vector PRODUCT TYPE: Ceiling System, 3' OC Report No.: Test Dates: 12/14/09 Through: 12/22/09 Report Date: 03/12/10 Expiration
More informationMetal Roofing Practical Design
Metal Roofing Practical Design Metal Roofing Practical Design Learning Outcomes Minimum Requirements Design Resources Low Slope Metal Roofing Design Details Continuously Insulated (Ci) Systems Minimum
More information800.406.7387 www.metalsales.us.com. Light Gauge Panels. Metal Sales Manufacturing Corporation
800.406.7387 www.metalsales.us.com Light Gauge Panels Metal Sales Manufacturing Corporation The Metal Sales Advantage Metal Sales Manufacturing Corporation continues to lead the industry with time-tested
More informationWhat makes DECRA Roofing Systems unique?
Commercial Roofing As the pioneer of stone coated steel technology, Roofing Systems have been proven around the world since 1957. Marketed and installed in over 120 countries, there are over 1 million
More informationReport on. Wind Resistance of Signs supported by. Glass Fiber Reinforced Concrete (GFRC) Pillars
Report on Wind Resistance of Signs supported by Glass Fiber Reinforced Concrete (GFRC) Pillars Prepared for US Sign and Fabrication Corporation January, 2006 SUMMARY This study found the attachment of
More informationDesign & Installation Solutions
Design & Installation Solutions Version 3.04 Roof Hugger, Inc P: 1-800-771-1711 Patent Nos. 5557903. 8024906 and Others Pending Design and Installation Guide To Metal-over-Metal Retrofit Roof Systems Version
More informationCHAPTER VII. TITLE: STANDARDS FOR NEW ROOFING July 2015 CONSTRUCTION, RE-ROOFING CONSTRUCTION AND ROOFING SYSTEM GUARANTEE REQUIREMENTS
TITLE: STANDARDS FOR NEW ROOFING CONSTRUCTION, RE-ROOFING CONSTRUCTION AND ROOFING SYSTEM GUARANTEE REQUIREMENTS Responsible Organization: Office of Facilities Planning Instructions: This Manual supersedes
More informationmetal architectural systems
metal architectural systems inspiring Every building has a story to tell a character in its own environment, reflecting a unique and carefully considered design. And the building envelope whether bold,
More informationYour Guide To Retrofit Sub-Framing Solutions
Your Guide To Retrofit Sub-Framing Solutions ROOF HUGGER THE LEADERS IN METAL-OVER-METAL RE-ROOFING SYSTEMS www.roofhugger.com TABLE OF CONTENTS 3 Customer Comments 4 Retrofit Roofing Benefits and Advantages
More information1997 Uniform Administrative Code Amendment for Earthen Material and Straw Bale Structures Tucson/Pima County, Arizona
for Earthen Material and Straw Bale Structures SECTION 70 - GENERAL "APPENDIX CHAPTER 7 - EARTHEN MATERIAL STRUCTURES 70. Purpose. The purpose of this chapter is to establish minimum standards of safety
More informationRouse Life Sciences Roof Repair or Replacement 07 61 13 SECTION 07 61 13
1. PART 1 - GENERAL 1.1 DESCRIPTION OF WORK SECTION 07 61 13 STANDING SEAM METAL ROOFING 1. This Section covers the pre-finished, pre-fabricated Architectural standing seam roof system. All metal trim,
More informationASTM E 1886 / ASTM E 1996 AND ASTM E 283, ASTM E 330, ASTM E 331 TEST REPORT. Rendered to: BEKAERT SPECIALTY FILMS, LLC
ASTM E 1886 / ASTM E 1996 AND ASTM E 283, ASTM E 330, ASTM E 331 TEST REPORT Rendered to: BEKAERT SPECIALTY FILMS, LLC SERIES/MODEL: Panorama 8-mil Film PRODUCT TYPE: Fixed Window with Applied Film This
More informationISO Types 1-6: Construction Code Descriptions
ISO 1 Frame (combustible walls and/or roof) Class 1B Buildings where the exterior walls are wood or other combustible materials, including construction where the combustible materials are combined with
More informationSUNPAL Multiwall Polycarbonate Standing-Seam Architectural System
SUNPAL Multiwall Polycarbonate Standing-Seam Architectural System Technical Guide Creating New Solutions for over 40 Years www.palram.com Contents Page Introduction 3 Panel Specification 4 Colors and Solar
More information