Plate clamp with safety lock model TBL 500-3000 This clamp is primarily used for transporting single steel plates in the vertical position, as well as lifting and turning through 180. This clamp can also be used for transporting steel constructions and profiles. It is recoended to use a pair of plate clamps in conjunction with a spreader beam for large sized sheets and long materials which have a tendency to sag. The jaw can be opened and closed with the locking lever (except for the TBL 0.5 t which uses a positive spring-loaded cam). The safety lock overrides the spring-loaded cam, preventing the clamp from opening even when there is no load. This plate clamp is service-friendly, making it easy to exchange parts, which are available individually or in kits. Clamp repair is available by the factory, or can be done by certified and experienced staff. The TBL 0.5 is equipped with a safety lock (positive spring-loaded cam), but comes without locking lever. The min. load is 10 % of the nominal WLL. Technical data model TBL Jaw capacity Z The surface hardness of the material must not exceed HRC 30/Brinell 300. TBL 0.5 *550000 500 0-16 1.5 TBL 1.0 *550017 1000 0-20 3.0 TBL 2.0 *550024 2000 0-32 9.3 TBL 3.0 *550048 3000 0-32 9.3 Dimensions model TBL TBL 0.5 TBL 1.0 TBL 2.0 TBL 3.0 110 A, 99 126 192 192 B, 195 225 312 312 Ø C, 29 50 80 80 D, 33 49 75 75 E, 47 70 96 96 F, 50 82 100 100 G, 48 55 81 81 H, 11 12 20 20 I, 16 20 24 24
Plate clamp with safety lock model TBL 4000-30000 This clamp is primarily used for transporting single steel plates in the vertical position, as well as lifting and turning through 180. This clamp can also be used for transporting steel constructions and profiles. It is recoended to use a pair of plate clamps in conjunction with a spreader beam for large sized sheets and long materials which have a tendency to sag. These plate clamps have the same design and applications as the clamp model TBL with a capacity from 500-3000. The surface hardness of the material must not exceed HRC 30/Brinell 300. Technical data model TBL Jaw capacity Z The min. load is 10 % of the nominal WLL. TBL 4.0 S *556545 4000 0-32 11.2 TBL 4.0 L *556569 4000 30-60 11.9 TBL 6.0 S *557221 6000 0-50 20.6 TBL 6.0 L *556583 6000 50-100 23.2 TBL 8.0 S *557245 8000 0-50 24.2 TBL 8.0 L *557269 8000 50-100 28.8 TBL 10.0 S *557283 10000 0-50 29.5 TBL 10.0 L *557306 10000 50-100 35.1 TBL 12.0 S *557320 12000 0-50 52.1 TBL 12.0 L *557344 12000 50-100 63.0 TBL 15.0 S *552936 15000 0-50 76.0 TBL 15.0 L *552943 15000 50-100 86.0 TBL 20.0 S *552950 20000 0-65 123.0 TBL 20.0 L *551892 20000 65-130 135.0 TBL 30.0 S *552967 30000 0-65 195.0 TBL 30.0 L *552974 30000 65-130 256.0 Dimensions model TBL TBL 4.0 S TBL 4.0 L TBL 6.0 S TBL 6.0 L TBL 8.0 S TBL 8.0 L TBL 10.0 S TBL 10.0 L TBL 12.0 S TBL 12.0 L TBL 15.0 S TBL 15.0 L TBL 20.0 S TBL 20.0 L TBL 30.0 S TBL 30.0 L A, 197 228 293 362 293 362 293 362 360 460 360 460 462 560 462 560 B, 339 339 442 482 450 482 503 503 550 615 550 615 674 724 667 732 Ø C, 80 80 89 89 89 89 110 110 130 130 130 130 130 130 60 60 D, 68 68 95 114 95 114 95 114 125 175 125 175 165 195 165 195 E, 93 100 143 143 143 143 143 143 162 162 162 162 210 210 210 210 F, 110 110 129 129 129 129 139 139 154 154 204 204 235 235 295 295 G, 20 20 20 20 20 20 25 25 30 30 45 45 45 45 65 65 H, 32 32 35 35 42 42 45 45 55 55 55 55 65 65 66 67 111
Plate clamp with hinged hook ring and safety lock model TBS 1000-3000 The TBS plate clamp with hinged hook ring can be used for the safe handling of plates at various angles. It can lift plates from the horizontal and put down in the vertical or alternatively lift it over the edge by gripping it from the side. The hinged hook ring ensures adequate clamping force in every position. Depending on the angle of usage capacity restrictions have to be taken into account, as shown in the diagram below. The hinged hook ring has the added advantage of providing enough clamping force to hold a plate safely. Even when transporting large-sized plates with the 2-legged lifting system slipping of the load and damage to the clamp is avoided. In addition to transporting plates, this clamp is suitable for turning steel structures and welded constructions. The min. load is 10 % of the nominal WLL. The surface hardness of the material must not exceed HRC 30/Brinell 300. Technical data model TBS Jaw capacity Z TBS 1.0 *550031 1000 0-20 4.6 TBS 2.0 *550086 2000 0-32 14.3 TBS 3.0 *550079 3000 0-32 14.3 Dimensions model TBS TBS 1.0 TBS 2.0 TBS 3.0 A, 126 192 192 B, 270 382 382 Ø C, 50 80 80 D, 49 75 75 E, 70 96 96 F, 95 132 132 G, 63 92 92 H, 12 20 20 I, 23 30 30 112
Plate clamp with pivoting shackle and safety lock model TBS 4500-10000 The surface hardness of the material must not exceed HRC 30/Brinell 300. Technical data model TBS Jaw capacity Z TBS 4.5 *550352 4500 0-50 34.4 TBS 6.0 S *550383 6000 0-50 38.0 TBS 6.0 L *551250 6000 50-100 42.0 TBS 8.0 S *552578 8000 0-50 39.0 TBS 8.0 L *557528 8000 50-100 42.4 TBS 10.0 S *552516 10000 0-50 68.0 TBS 10.0 L *557542 10000 50-100 80.0 The min. load is 10 % of the nominal WLL. Dimensions model TBS TBS 4.5 TBS 6.0 S TBS 6.0 L TBS 8.0 S TBS 8.0 L TBS 10.0 S TBS 10.0 L A, 292 292 367 292 367 360 446 B, 675 737 785 737 785 903 921 C, 90 95 98 98 98 110 112 D, 180 176 180 176 180 195 195 Ø E, 27.8 27.8 27.8 27.8 27.8 33 33 F, 95 95 115 95 115 125 168 G, 143 143 143 143 143 162 162 H, 135 137 135 136 136 170 170 I, 185 188 188 210 210 223 223 113
Plate clamp model Shark 1000-2000 Features For the toughest operating conditions. This clamp is primarily used for transporting single steel plates in the vertical position, as well as lifting and turning through 180, up to a surface hardness of HRC 40. Quality as yet unknown for plate clamps, guarantees highest safety standards and an extremely long service life. Fulfils the requirements of all relevant standards and EU-Directives. Option Special jaws for a surface hardness up to HRC 50. Especially for alloyed / stainless steel and slippy surfaces. The surface hardness of the material must not exceed HRC 40. The min. load is 10 % of the nominal WLL. Technical data model Shark Jaw capacity Z Shark 1.0 *558808 1000 0-20 3.3 Shark 2.0 *558815 2000 0-32 6.8 Dimensions model Shark Shark 1.0 Shark 2.0 A, 120 170 B, 240 345 Ø C, 36 65 D, 42 58 E, 60 80 F, 72 88 G, 58 69 H, 12 15 I, 12 19 J, 137 191 K, 152 214 L, 210 302 114
The advantages at a glance: Embossed marking for unambiguous identification Smooth mechanical operation, tight tolerances, mechanically optimized, precise workmanship Easy maintenance, simple and fast replacement of wear parts Reinforcement on the lifting eye prevents it from twisting, during unintentional side / lateral pull Higher clamping forces. Optimized clamping forces in every position Heavy duty housing, drop forged, absolutely twist free Pivoting jaw guarantees that the full surface of the jaw makes contact with the plate surface, ensuring the safe turning of sheet metal and steel plates Patent pending for special jaws Special jaw 115
Plate clamp with hinged hook ring model Shark-S 1000-2000 Features For the toughest operating conditions. This clamp is primarily used for transporting single steel plates in the vertical position, as well as lifting and turning through 180, up to a surface hardness of HRC 40. With hinged hook ring to be used as a two-legged lifting system (see diagram of forces). Quality as yet unknown for plate clamps, guarantees highest safety standards and an extremely long service life. Fulfils the requirements of all relevant standards and EU-Directives. Option Special jaws for a surface hardness up to HRC 50. Especially for alloyed / stainless steel and slippy surfaces. The min. load is 10 % exceed of the nominal WLL. Technical data model Shark-S The surface hardness of the material must not HRC 40. Jaw capacity Z Shark-S 1.0 *558822 1000 0-20 3.6 Shark-S 2.0 *558839 2000 0-32 7.8 Dimensions model Shark-S Shark-S 1.0 Shark-S 2.0 A, 120 170 B, 248 349 Ø C, 38 65 D, 42 58 E, 60 80 F, 72 88 G, 58 69 H, 12 19 I, 13 20 J, 137 191 K, 152 214 L, 223 326 116
The advantages at a glance: Embossed marking for unambiguous identification Smooth mechanical operation, tight tolerances, mechanically optimized, precise workmanship Easy maintenance, simple and fast replacement of wear parts Hinged hook ring Higher clamping forces. Optimized clamping forces in every position Heavy duty housing, drop forged, absolutely twist free Pivoting jaw guarantees that the full surface of the jaw makes contact with the plate surface, ensuring the safe turning of sheet metal and steel plates Patent pending for special jaws Special jaw 117
Universal grab model TAG 350-10000 The universal grab TAG saves time, as it does not require chains, cables etc. when hoisting and loading material. The large jaw capacity allows to tackle a variety of sizes with only one clamp. It can be used for loading machine tools, lifting steel constructions, welding and assembly jobs as well as for concrete and prefabricated pieces. Features The automatic clamping force is retained by a positive tension spring, even if there is slack in the chain. The Quick-Open type universal grab opens by lifting and simultaneously pulling the lever out against the tension spring. The jaw is closed by the spring. Universal grabs up to 2.0 t capacity are equipped with round chains, clamps with higher capacities are delivered with roller chains. Option Grabs up to 1.25 t WLL are available with a protective lining on the clamping jaws upon request. This results in a decrease of the jaw capacity by 10. The surface hardness of the material must not exceed HRC 30/Brinell 300. Special version of universal grab model TAG with modified side plates for use in confined spaces. 118
Technical data model TAG Jaw width Jaw capacity TAG 0.35/100 *550413 350 100 0-100 8.7 TAG 0.35/200 *551724 350 200 90-200 16.3 TAG 0.75/100 *550253 750 100 0-100 8.6 TAG 0.75/200 *552806 750 200 90-200 16.6 TAG 1.25/100 *550468 1250 100 0-100 14.9 TAG 1.25/200 *551502 1250 200 90-200 24.3 TAG 2.0/100 *550642 2000 100 0-100 20.8 TAG 2.0/200 *551366 2000 200 90-200 29.1 TAG 3.0/90 *550840 3000 90 5-90 26.5 TAG 5.0/90 *550345 5000 90 5-90 30.5 TAG 5.0/170 *551915 5000 170 80-170 43.8 TAG 10.0/100 *552059 10000 100 0-100 70.0 TAG 10.0/200 *553001 10000 200 100-200 105.0 Dimensions model TAG TAG 0.35/100 TAG 0.35/200 TAG 0.75/100 TAG 0.75/200 TAG 1.25/100 TAG 1.25/200 TAG 2.0/100 TAG 2.0/200 TAG 3.0/90 TAG 5.0/90 TAG 5.0/170 TAG 10.0/100 TAG 10.0/200 A, 264 382 264 382 320 382 328 375 297 297 354 405 440 B, 259 434 259 434 289 434 415 515 290 290 423 423 562 C, 128 195 128 195 128 195 135 195 136 136 180 160 200 D, 100 156 100 156 100 156 115 165 106 106 155 130 175 E, 100 200 100 200 100 200 100 200 90 90 170 100 200 F, 85 120 85 120 85 120 105 160 91 91 118 160 183 G, 550 760 550 760 570 760 571 750 570 570 620 720 840 H, 75 75 75 75 75 75 75 75 82 82 82 102 102 I, 121 121 121 121 121 121 121 121 111 111 111 144 144 J, 20 20 20 20 20 20 20 20 32 32 32 40 40 K, 78 90 83 90 83 90 105 105 137 147 147 208 208 TAG Only for model TAG up to 2.0 t The min. load is 10 % of the nominal WLL. 119
In order to achieve a maximum capacity, the contact surface should be bright and free from dirt, oil, grease, scale, corrosion, paint etc. Permanent load lifting magnets model TPM 100-1000 (Flat material), 50-500 (Round material) TPM load lifting magnets are ideal tools for easy, quick and thus economical transport of heavy objects made of ferro-magnetic material. Typical operating areas are workshops and warehouses, loading and unloading of machines as well as construction of jigs and fixtures. Compact design of the units for a large number of applications. The load is not affected mechanically which allows lifting of flat as well as round material. The efficient magnet body provides strong lifting capacity at low dead weight. The permanent magnets do not require electric energy and will leave only minor residual magnetism on the material after use. The magnets are activated / deactivated easily by turning a locking lever. In activated condition the hand lever will be safely locked and thus prevent unintended demagnetising. The selection of the appropriate magnet model should be made under consideration of the varying conditions of the contact surface, kind of material alloy and plate thickness / bar diameter (see table). 120
Technical data model TPM Flat material capacity** max. Material thickness min. Flat material length of material max. Round material capacity** max. Round material diameter Round material length of material max. Test load TPM 0.1 *558853 100 14 2000 50 200-300 2000 300 TPM 0.3 *558860 300 20 2500 150 200-300 2500 900 TPM 0.5 *558877 500 24 3000 250 200-400 3000 1500 TPM 0.8 *558884 800 34 3500 400 200-400 3500 2400 TPM 1.0 *558891 1000 40 3500 500 200-400 3500 3000 ** measured on mild steel St 37 Dimensions model TPM TPM 0.1 TPM 0.3 TPM 0.5 TPM 0.8 TPM 1.0 A, 122 192 232 302 332 B, 69 95 120 154 154 C, 185 225 270 320 320 D, 160 250 250 450 450 Percent of max. capacity 100 % 75 % 50 % 25 % 0 % TPM 1000 TPM 800 TPM 500 TPM 300 TPM 100 0 0,5 1,0 1,5 Air gap in Plate thickness in 85 80 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 TPM 1000 TPM 800 TPM 500 TPM 300 TPM 100 0 100 % 75 % 50 % 0 % Percent of max. capacity Diagram: WLL/air gap Diagram: WLL/material thickness TPM Reduction of capacity % of capacity Correct use On/Off Temperature 60 C 100 % Humidity 80 % 100 % St 52 95 % Alloy steel 80 % High carbon steel 70 % Cast iron 45 % Nickel 45 % Austenitic, stainless steel 0 % Brass 0 % Aluminium 0 % 121
Non-marring grab model TBP 500-1500 The TBP non-marring grab is suitable for lifting, turning and transporting of plates with a sensitive surface without leaving behind indentations. It can be used for aluminium and stainless steel plate or those with an extremely hard surface. The surface of the plate must be free of oil, grease or any other liquid to ensure safe transport. Technical data model TBP Jaw capacity Z TBP 0.5 *556378 500 0-10 3.0 TBP 1.5 *556392 1500 0-20 12.6 Dimensions model TBP TBP 0.5 TBP 1.5 A, 127 215 B, 200 345 D, 52 75 E, 69 135 F, 87 131 G, 76 118 H, 13 20 I, 20 24 Ø C, 55 85 The min. load is 10 % of the nominal WLL. TBP 122
Non-marring grab with chain model TSB The TSB grab has parallel-facing jaws that equally distribute the clamping pressure over a relatively large surface area. This makes the grab attractive for plate material with sensitive surfaces. The protective lining Bremsit offers an outstanding friction coefficient, thereby enhancing the grip of the jaws. This lining can be easily replaced when worn. Similar to the universal grab, this grab has a large jaw capacity and the security of a safety lock device with a hold-open/hold-closed feature. The surface of the plate must be free of oil, grease or any other liquid to ensure safe transport. Technical data model TSB Jaw capacity Z TSB 0.35/65 *550772 350 0-65 11.6 TSB 0.75/65 *550826 750 0-65 11.8 TSB 1.25/65 *550727 1250 0-65 16.7 Dimensions model TSB TSB 0.35/65 TSB 0.75/65 TSB 1.25/65 A, 270 270 270 B, 260 260 260 C, 128 128 128 D, 100 100 100 E, 65 65 65 F, 78 78 78 The min. load is 10 % of the nominal WLL. TSB TSB 123
Girder grab for horizontal transport model TTG 500-7500 The girder grab TTG is designed for the horizontal transport of girders, metal plates, profiles etc. The offset suspension lug ensures that the flange of the girder will be kept practically horizontal during transport. The positive safety lock keeps the clamp safely locked, even before the lift begins. This allows the operator to place the clamp, lock it closed and move away from the load. The lever ensures easy opening and closing of the clamping jaw and has a lock open feature. When transporting long girders, it is recoended to use a pair of clamps in conjunction with a spreader beam. Technical data model TTG Jaw capacity TTG 0.5 *557931 500 0-20 2.9 TTG 1.5 *550239 1500 0-30 6.8 TTG 3.0 *550192 3000 0-35 11.3 TTG 4.5 *550451 4500 0-40 14.8 TTG 7.5 *551205 7500 0-45 30.0 Dimensions model TTG TTG 0.5 TTG 1.5 TTG 3.0 TTG 4.5 TTG 7.5 Ø A, 50 70 80 90 110 B, 36 43 55 60 64 C, 25 35 42 46 55 D, 148 140 180 196 222 E, 200 180 214 248 304 F, 27 40 40 40 50 G, 20 30 32 35 42 H, 95 155 190 207 237 I, 110 230 284 314 367 J, 10 15 20 20 22 K, 56 50 60 64 90 L, 85 100 114 117 143 M, 13 16 20 25 30 TTG 124
Girder grab for vertical transport model TTR 750-3000 The girder grab TTR is designed for vertical transport, especially for lifting and stacking of girders. The unique position of the offset suspension lug keeps the girder virtually in a vertical position during transport. The positive safety lock keeps the clamp safely locked, even before the lift begins. This allows the operator to place the clamp, lock it closed and move away from the load. The lever ensures easy opening and closing of the clamping jaw and has a lock open feature. When transporting long girders, it is recoended to use a pair of clamps in conjunction with a spreader beam. Technical data model TTR Jaw capacity TTR 0.75 *550499 750 5-16 3.1 TTR 1.50 *550246 1500 5-25 6.8 TTR 3.00 *550550 3000 5-28 10.9 Dimensions model TTR TTR 0.75 TTR 1.50 TTR 3.00 A, 24 33 37 B, 40 53 56 C, 132 176 194 D, 62 76 78 E, 145 190 208 F, 118 152 163 Ø G, 50 70 80 H, 12 15 20 I, 12 17 23 K, 53 69 85 TTR 125
Girder grab for horizontal transport model TTT 750-4500 The girder grab TTT is used for the horizontal transport of steel girders. Due to the split fixed jaw, it can be positioned centrally on the end of the beam. The grab should only be used in pairs. The safety lock with positive spring tension holds the grab in position on the end of the girder even without load tension. The lever is used to engage and disengage the jaw and to keep it open. The angle from the vertical must not exceed 30. Technical data model TTT Jaw capacity TTT 0.75 *558501 750 0-20 3 TTT 1.5 *558518 1500 0-35 6 TTT 3.0 *558525 3000 0-40 10 TTT 4.5 *558532 4500 0-45 16 Dimensions model TTT TTT 0.75 TTT 1.5 TTT 3.0 TTT 4.5 A, 30 38 50 60 B, 70 70 75 90 C, 100 155 195 222 D, 142 150 195 222 Ø E, 50 70 80 90 F, 16 19 19 22 G, 16 20 25 30 H, 225 335 400 450 I, 45 45 80 90 J, 200 210 214 248 K, 106 120 125 147 L, 52 66 80 88 TTT 126
Technical data model TCH Tigrip Load Hoisting Tackle Horizontal lifting gear, model TCH 1000-10000 The TCH horizontal lifting gear consists of two clamps with a two-legged chain sling. It is especially suited for the transport of single plates with a minimum thickness of approx. 5 as well as for plate bundles. The two-legged version is appropriate for normal sized plates. For extra large or long plates, it is recoended to use two sets of the two-legged lifting gears in conjunction with a spreader beam. In the standard version, the lifting clamp is suitable for plates up to 1500 width. Lifting gears with longer chains for larger plate widths are available upon request. The capacity applies to a pair of lifting clamps. Single clamps are also available. The angle from the vertical must not exceed 45. for lifting gear, two-legged single clamp * Jaw capacity ** TCH 1.0 *551625 *551212 1000 0-50 13.0 TCH 2.0 *551991 *551168 2000 5-32 17.7 TCH 4.0 *551755 *550895 4000 5-50 31.0 TCH 6.0 *553230 *550888 6000 5-75 69.0 TCH 8.0 *553247 *552097 8000 5-75 72.0 TCH 10.0/1 *553254 *551465 10000 5-100 93.8 TCH 10.0/2 *552042 *552738 10000 50-150 108.6 * Per pair, up to an angle of 45 from the vertical ** for two single clamps with chain Dimensions model TCH TCH 1.0 TCH 2.0 TCH 4.0 TCH 6.0 TCH 8.0 TCH 10.0/1 TCH 10.0/2 A, 135 160 180 200 260 300 300 B, 75 90 100 110 140 160 160 Ø C, 18 22 26 32 36 40 40 D, 15 32 44 58 56 70 66 E, 82 83 114 172 170 216 218 F, 65 61 75 97 100 116 116 G, 100 100 99 129 128 149 150 H, 32 49 62 90 90 113 113 I, 44 72 89 127 130 113 113 Ø J, 13 19 26 36 37 50 50 TCH 127
ratings are valid for a complete two-legged chain system. Also available as single clamp (without shackle). The angle from the vertical must not exceed 45. Horizontal lifting gear model TGF 350-6650 The TGF horizontal lifting gear consists of two clamps with a two-legged chain sling and is especially suited for the transport of plate bundles. For the transport of stainless steel plate bundles, plywood bundles, etc. the clamps are optionally available with flat jaws and protective lining. The clamps are easily adjusted to the height of the plate by a special ratcheting lever. The lifting clamps are available in special versions for bundle thicknesses up to 400. Scope of delivery for horizontal lifting gear: 2 clamps and two-legged chain sling for plate width 1500. Technical data model TGF Horizontal lifting clamp, two-legged Single clamp * Jaw capacity Z ** TGF 0.3/150 *553087 *553216 350 0-150 21 TGF 0.6/150 *553094 *553223 650 0-150 22 TGF 1.3/150 *552745 *552554 1300 0-150 23 TGF 2.3/150 *551731 *551809 2300 0-150 33 TGF 3.3/150 *551342 *550833 3300 0-150 39 TGF 5.0/150 *553100 *553322 5000 0-150 59 TGF 6.6/150 *553117 *551885 6650 0-150 65 TGF 0.3/250 *552882 *553339 350 0-250 21 TGF 0.6/250 *553124 *552387 650 0-250 22 TGF 1.3/250 *552608 *553346 1300 0-250 23 TGF 2.3/250 *552363 *552622 2300 0-250 33 TGF 3.3/250 *553131 *551540 3300 0-250 39 TGF 5.0/250 *552189 *553353 5000 0-250 59 TGF 6.6/250 *553148 *551656 6650 0-250 87 * Complete two-legged lifting gear, angle from the vertical max. 45 ** Complete two-legged lifting gear TGF Dimensions model TGF TGF 0.3/150 TGF 0.6/150 TGF 1.3/150 TGF 2.3/150 TGF 3.3/150 TGF 5.0/150 TGF 6.6/150 TGF 0.3/250 TGF 0.6/250 TGF 1.3/250 TGF 2.3/250 TGF 3.3/250 TGF 5.0/250 TGF 6.6/250 A, 298 298 298 321 321 405 405 448 448 448 417 417 495 495 B, 122 122 122 130 130 185 185 122 122 122 130 130 185 185 C, 160 160 160 160 160 210 210 140 140 140 160 160 210 210 D, 41 41 41 50 50 82 82 41 41 41 60 60 82 82 Ø E, 20 20 20 23 23 30 30 20 20 20 23 23 30 30 F, 80 80 80 80 80 100 100 80 80 80 80 80 100 100 G, 20 20 20 25 25 30 30 20 20 20 25 25 30 30 Ø H, 25 25 25 25 25 40 40 25 25 25 25 25 40 40 128
Horizontal lifting hook model BVH 500-7500 The BVH horizontal lifting hooks are used in pairs with chain or wire rope slings to lift plate bundles that are relatively close to the ground. The high tensile hooks have a serrated lifting surface. The angle from the vertical must be 30-45. The chain has to be in line with the crank of the lifting hooks. Technical data model BVH ** BVH 0.5 *557023 500 1.2 BVH 1.12 *557047 1120 1.4 BVH 1.5 *557061 1500 2.4 BVH 2.0 *557085 2000 3.9 BVH 2.5 *557108 2500 8.2 BVH 3.2 *557122 3200 8.3 BVH 4.0 *557146 4000 13.6 BVH 5.0 *557160 5000 21.0 BVH 6.0 *557184 6000 39.0 BVH 7.5 *557207 7500 60.0 ** Per unit BVH Dimensions model BVH BVH 0.5 BVH 1.12 BVH 1.5 BVH 2.0 BVH 2.5 BVH 3.2 BVH 4.0 BVH 5.0 BVH 6.0 BVH 7.5 A, 180 210 240 280 340 400 530 660 800 980 B, 50 60 70 80 100 120 160 200 250 300 C, 80 95 105 115 120 140 180 210 250 300 D, 18 20 22 26 32 32 36 40 50 60 E, 150 170 200 220 270 320 420 520 640 760 129
Lifting clamp with safety lock model THS 750-4500 The THS lifting clamp is normally used in pairs especially for the horizontal transport of plates. The transport of slightly sagging plates is also possible. Individually, it can be used to load presses shears, and other machines. The safety lock is preventing the clamp from opening, even when there is no load. The jaws can be opened and closed with the safety lock lever. This clamp has a lock-open feature. Option The models THS 1.5 and THS 3.0 are available with a hinged hook ring upon request. Technical data model THS * Jaw capacity THS 0.75 *551267 750 0-20 3.2 THS 1.5 *550734 1500 0-35 6.1 THS 3.0 *551373 3000 0-40 12.7 THS 4.5 *553483 4500 0-40 16.5 * Per unit Dimensions model THS THS 0.75 THS 1.5 THS 3.0 THS 4.5 A, 30 38 45 47 B, 70 80 95 110 C, 130 165 205 235 D, 97 120 160 196 Ø E, 50 70 80 90 F, 12 15 20 20 G, 15 17 25 30 H, 255 335 400 450 I, 15 20 30 59 J, 135 165 195 230 K, 80 90 100 110 L, 40 50 60 64 THS 130
Lifting clamp model TWH 1500-5000 The TWH lifting clamp, when used in pairs, is wellsuited for horizontal transport of individual and bundled plates. The clamp is not suited for thin plates that have a tendency to sag during transport. It is normally used in combination with a two-legged chain sling. The capacity (WLL) applies to a pair of lifting clamps. Option Protective lining The angle from the vertical must not exceed 45. Technical data model TWH * Jaw capacity ** TWH 30 with rollers *550529 1500 5-60 5.6 TWH 50 with rollers *551441 2500 10-70 10.3 TWH 70 with rollers *551380 3500 10-80 13.4 TWH 100 with rollers *551618 5000 10-102 27.7 TWH 30 with plate *555654 1500 5-60 5.7 TWH 50 with plate *555661 2500 10-70 10.3 TWH 70 with plate *555678 3500 10-80 13.5 TWH 100 with plate *555685 5000 10-102 27.8 * Per pair, angle from the vertical max. 45 ** Per unit TWH with rollers Dimensions model TWH TWH 30 with rollers TWH 50 with rollers TWH 70 with rollers TWH 100 with rollers TWH 30 with plate TWH 50 with plate TWH 70 with plate TWH 100 with plate A, 5 10 10 10 5 10 10 10 B, 60 70 80 102 60 70 80 102 C, 60 75 90 110 60 75 90 110 D, 105 130 162 170 105 130 162 170 E, 250 315 345 425 250 315 345 425 F, 200 275 292 345 200 275 292 345 G, 22 38 48 45 22 38 48 45 H, 30 30 30 45 30 30 30 45 J, 12 12 15 20 12 12 15 20 K, 50 64 64 89 50 64 64 89 L, 73 92 92 130 73 92 92 130 Ø M, 18 25 25 35 18 25 25 35 N, 36 58 65 80 36 58 65 80 P, 65 77 105 120 65 77 105 120 R, 120 150 185 210 120 150 185 210 S, 100 100 100 120 100 100 100 120 T, 10 10 10 12 10 10 10 12 TWH with plate 131
Lifting clamp model THK 750-9000 The THK lifting clamp, when used in pairs, is especially well-suited for horizontal transport of thin plates that have a tendency to sag. It is normally used in combination with a two-legged chain sling. The capacity applies to a pair of lifting clamps. The angle from the vertical must not exceed 30. Technical data model THK * Jaw capacity ** THK 0.75 *550628 750 0-25 1.7 THK 1.5 *550284 1500 0-35 3.2 THK 3.0 *550390 3000 0-35 5.7 THK 4.5 *551120 4500 0-45 8.4 THK 6.0 *551038 6000 0-60 11.6 THK 9.0 *551960 9000 0-60 17.9 * Per pair, angle up to 30 from the vertical ** Per unit Dimensions model THK THK 0.75 THK 1.5 THK 3.0 THK 4.5 THK 6.0 THK 9.0 A, 25 36 38 48 63 65 B, 72 80 93 103 124 113 C, 118 135 168 183 214 223 D, 81 102 119 140 176 188 Ø E, 20 25 30 30 35 40 F, 161 198 227 238 284 317 G, 12 15 20 25 30 35 H, 86 102 110 122 110 148 I, 12 15 20 20 20 20 THK 132
Board clamp model TPZ 400 The TPZ clamp is made for lifting and vertically transporting wood, particle board and plastic sheets. The pliers are fastened to the plate with the aid of a hand-held lever. The jaw, which has a protective lining, grabs once lifting begins and holds the board securely. Technical data model TPZ Jaw capacity Z TPZ 0.4/55 *555234 400 5-55 6.3 TPZ 0.4/100 *558983 400 55-100 9.0 TPZ 0.75/60 *558990 750 5-60 12.0 TPZ 0.75/120 *559003 750 60-120 14.0 Dimensions model TPZ TPZ 0.4/55 TPZ 0.4/100 TPZ 0.75/60 TPZ 0.75/120 A, 120 120 155 155 B, 290 335 349 406 C, 525 525 545 560 D, 125 125 145 145 E, 117 117 135 135 F, 60 60 121 121 G, 40 40 75 75 H, 6 6 8 x 24 8 x 24 TPZ, up to 400 equipped with rope, from 750 equipped with chain. 133
In order to achieve a maximum capacity, the contact surface should be bright and free from dirt, oil, grease, scale, corrosion, paint etc. Manual claw, magnetic model THM 120-170 The THM manual magnetic claw is used for transporting steel sheets horizontally and vertically, lifting plates from racks, pulling steel sheets out of shelving, as well as transporting flat pieces of magnetizable steel. The clamp, depending on the type, can be used for plate thicknesses from 1 to 5. Pressing down on the handle activates a cam which releases the magnetic claw from the workpiece. This manual claw is maintenance-free and keeps the magnetic force for an unlimited period of time. Technical data model THM Lifting capacity* Pulling capacity* THM 120 *550963 120 70 2 THM 170 *550437 170 100 2 * Measured at a safety factor 2:1 on bright drawn material St 37 k Dimensions model THM THM 120 THM 170 A, 84 116 B, 140 140 C, 130 130 D, 25 25 E, 172 172 THM 134
Hand clamp model THG 250 The THG hand clamp is suited for the individual transport of light and thin plates. Pressing down on the hand grip releases the tension spring, allowing the clamp to open and slide onto the plate. The plate can be transported by holding onto the ergonomically designed hand grip. The positive spring pressure prevents the plate from accidental slipping out of the clamp. The plate surface of the material must not exceed a hardness of HRC 30. Technical data model THG Jaw capacity THG *556057 250 0-10 1.4 Dimensions model THG THG A, 184 B, 105 C, 12 D, 53 Thickness, 40 THG Attaching Transport 135
Screw clamp for vertical and horizontal pulling model TSH 750-5000 The screw clamp offers many possible applications. It is particularly useful for lifting, turning and pulling steel plates, girders and steel constructions. The spindle is closed only finger tight. Once the screw clamp is tightened and lifting begins, the pivoting pad clamping system produces a wedging action against the material, holding it securely. The plate surface of the material must not exceed a hardness level of HRC 50. Technical data model TSH Jaw capacity Z TSH 0.75 *559027 750 0-30 3.1 TSH 1.5 *550123 1500 0-32 7.4 TSH 3.0 *550154 3000 0-50 11.4 TSH 5.0 *550215 5000 0-80 27.6 Dimensions model TSH TSH 0.75 TSH 1.5 TSH 3.0 TSH 5.0 Pawl A, 190 255 290 470 B, 52 65 74 130 Ø C, 19 26 30 50 D, 43 75 85 135 E, 113 130 170 225 F, 35 44 50 72 X, 15 40 40 50 TSH Safety spring Ball Pivoting bearing Pad Functional drawing pivoting pad 136
Screw clamp for lifting and pulling model TSD 1500-7500 The TSD screw clamp is a valuable asset when lifting, pulling and fitting sheet material as well as steel constructions. The spindle is closed only finger tight. When the screw clamp is tightened and lifting begins, the pivoting pad clamping system produces a wedging action against the material, holding it securely. The plate surface of the material must not exceed a hardness level of HRC 50. Technical data model TSD Jaw capacity Z TSD 1.5 *550598 1500 0-35 4.8 TSD 3.0 *550864 3000 0-35 8.1 TSD 5.0 *551717 5000 0-40 14.5 TSD 7.5 *550987 7500 0-40 18.1 Pawl Dimensions model TSD TSD 1.5 TSD 3.0 TSD 5.0 TSD 7.5 A, 191 235 275 295 Ø B, 35 46 55 65 C, 24 34 40 50 D, 16 17 18 22 E, 60 67 85 92 F, 105 120 150 162 G, 50 60 75 80 TSD Safety spring Ball Pivoting bearing Pad Functional drawing pivoting pad 137
Screw clamp for three-dimensional pulling model TSZ 500-7500 The TSZ screw clamp is designed to pull in three directions. It offers many different possibilities for transporting steel constructions, feeding machining centres, etc. The spindle is closed only finger tight. When the screw clamp is tightened and lifting begins, the pivoting pad clamping system produces a wedging action against the material, holding it securely. The plate surface of the material must not exceed a hardness level of HRC 50. Technical data model TSZ Jaw capacity TSZ 0.5 *555739 500 0-28 2.3 TSZ 1.5 *555746 1500 0-35 5.6 TSZ 3.0 *555753 3000 0-35 8.8 TSZ 5.0 *555760 5000 0-40 16.2 TSZ 7.5 *555777 7500 0-40 20.9 Pawl Dimensions model TSZ TSZ 0.5 TSZ 1.5 TSZ 3.0 TSZ 5.0 TSZ 7.5 A, 28 35 35 40 40 B, 43 60 67 85 92 C, 45 55 65 75 75 D, 125 158 195 230 240 E, 72 93 114 133 143 F, 83 99 120 150 162 Ø G, 26 35 46 55 65 H, 16 24 34 40 50 I, 12 16 17 18 23 J, 35 50 60 75 80 TSZ Ball Pivoting bearing Safety spring Pad Functional drawing pivoting pad 138
Roundstock grab model TRU 100-4000 The TRU roundstock grab picks up roundstock and pipe material up to 600 in diameter quickly and safely. With its optional protective lining, it can also pick up materials with sensitive surfaces. When using protective lining, it is important that the surfaces are dry, clean and free of oil and grease. Technical data model TRU with protective lining Jaw capacity Z TRU 0.1/150 *550918 *551632 100 50-150 3.9 TRU 0.5/200 *550475 *551151 500 35-200 13.6 TRU 1.0/200 *550949 *552165 1000 35-200 13.6 TRU 1.5/300 *550505 *550512 1500 80-300 27.0 TRU 3.0/300 *550758 *550536 3000 80-300 49.0 TRU 4.0/600 *551526 *550406 4000 200-600 204.0 Dimensions model TRU Locking pawl TRU 0.1/150 TRU 0.5/200 TRU 1.0/200 TRU 1.5/300 TRU 3.0/300 TRU 4.0/600 A, 270 503 509 720 740 1420 Bmin., 292 417 437 520 582 930 Bmax., 458 723 745 937 960 1815 C, 97 150 178 204 220 318 D, 43 56 82 84 125 205 E, 8 15 15 20 20 30 F, 17 17 30 25 30 35 Shackle TRU, shackle for grabs for 2 t and up capacity. Locking pawl locks open grab in place. 139
Pipe grab model TR 200-3000 The TR pipe grab for rolls and pipes up to 1050 in diameter offers a large variety of different applications. Apart from pipe and drums laid on their side, this lightweight pipe grab will also handle rolls of paper, fabric, sheet metal and tubes. The grab can be ordered with a protective lining made of Bremsit or hard rubber for extra protection in lifting loads with sensitive surface. The picture shows a customized grab. Standard delivery without rollers as shown in technical drawing. Locking pawl When using protective lining, it is important that the surfaces are dry, clean and free of oil and grease. Hook ring TR, hook ring for grabs for 2 t and above. Locking pawl keeps the grab in the open position. Technical data model TR with protective lining Jaw capacity TR 0.2/550 *553506 *552585 200 350-550 34 TR 0.2/650 *553513 *554978 200 450-650 41 TR 0.3/750 *553520 *554985 300 500-750 47 TR 0.5/750 *553537 *551700 500 500-750 47 TR 0.5/900 *553544 *552400 500 650-900 54 TR 0.75/105 *552561 *554992 750 700-1050 56 TR 1.0/750 *553551 *555005 1000 500-750 55 TR 1.0/1050 *553568 *555012 1000 700-1050 71 TR 2.0/1050 *553575 *555029 2000 700-1050 135 TR 3.0/1050 *553582 *555036 3000 700-1050 154 Dimensions model TR TR 0.2/550 TR 0.2/650 TR 0.3/750 TR 0.5/750 TR 0.5/900 TR 0.75/105 TR 1.0/750 TR 1.0/1050 TR 2.0/1050 TR 3.0/1050 A, 800 900 1100 1100 1150 1300 1000 1350 1350 1350 B, 565 615 665 665 765 815 665 815 815 815 Ø D, 550 650 750 750 900 1050 750 1050 1050 1050 E, 550 550 550 550 550 550 550 550 800 800 F, 35 35 35 35 35 35 35 35 45 45 G, 20 20 20 20 20 20 20 20 30 30 Ø C, 350 450 500 500 650 700 500 700 700 700 140
Profile steel grab model TPR 500-3000 The TPR steel grab is designed for transport of girders, profile steel, etc. It boasts a large jaw capacity, which makes it useful for various flange widths. The clamping jaws press securely with a positive fit to the girder. Technical data model TPR Jaw capacity Z TPR 0.5/200 *551496 500 0-200 15.0 TPR 1.5/300 *551045 1500 0-300 22.6 TPR 3.0/300 *553490 3000 0-300 41.7 Dimensions model TPR TPR 0.5/200 TPR 1.5/300 TPR 3.0/300 Locking pawl A, 510 710 720 Bmin., 390 495 525 Bmax., 625 830 920 C, 200 200 220 D, 15 15 20 E, 30 30 43 Shackle TPR, shackle for grabs for 2 t and up capacity. Locking pawl locks open grab in place. 141
Block grab model TVB 250/500 The TVB block grab is useful for the transport of stone and concrete blocks and other materials with parallel surfaces. The grab has a protective lining to ensure a safe and non-marring transport. The clamping jaw and the center of gravity are easily and quickly adjustable by means of the locking pin. It is important that the surfaces are dry, clean and free of oil and grease. Technical data model TVB Jaw capacity Z TVB 500 *556989 0.25/0.5 0-240 13 Dimensions model TVB TVB 500 A, 537 B, 296 C, 112 D, 80 E, 75 F, 85 Ø G, 22 Ø H, 10 TVB 142
Stone/concrete grab with small jaw capacity model TBG 200-2500 The TBG block grabs are suited for the transport of all materials with parallel surfaces that can withstand a clamping pressure twice as high as the load being lifted. The grabs are delivered with a replaceable hard rubber protective lining as standard. When using rubber protective lining it is important that the surfaces are dry, clean and free of oil and grease. Technical data model TBG Jaw capacity Z TBG 0.2/150 *552141 200 0-150 24 TBG 0.3/150 *553599 300 0-150 27 TBG 0.5/150 *552455 500 0-150 27 TBG 1.0/250 *552356 1000 50-250 50 TBG 1.5/250 *552394 1500 50-250 50 TBG 2.5/250 *551571 2500 50-250 79 Dimensions model TBG TBG 0.2/150 TBG 0.3/150 TBG 0.5/150 TBG 1.0/250 TBG 1.5/250 TBG 2.5/250 A, 815 815 815 1050 1050 1050 Bmin., 420 420 420 460 460 460 Bmax., 760 760 760 980 980 980 C, 200 200 200 250 250 250 D, 160 160 160 160 160 160 E, 30 30 30 29 29 29 F, 15 15 15 20 20 25 TBG with small jaw 143
Stone / concrete grab with large jaw capacity model TBG 200-5000 The units are delivered with protective linings as standard. Technical data model TBG Jaw capacity Z TBG 0.2/500 *551489 200 200-500 49 TBG 0.3/700 *551816 300 400-700 52 TBG 0.5/900 *552288 500 600-900 55 TBG 1.0/400 *553612 1000 100-400 51 TBG 1.0/1100 *552134 1000 800-1100 72 TBG 1.5/1300 *553605 1500 1000-1300 128 TBG 2.0/500 *553629 2000 200-500 126 TBG 3.0/500 *553636 3000 200-500 160 TBG 4.0/500 *553643 4000 200-500 240 TBG 5.0/500 *553650 5000 200-500 270 When using rubber protective lining it is important that the surfaces are dry, clean and free of oil and grease. Dimensions model TBG TBG 0.2/500 TBG 0.3/700 TBG 0.5/900 TBG 1.0/400 TBG 1.0/1100 TBG 1.5/1300 TBG 2.0/500 TBG 3.0/500 TBG 4.0/500 TBG 5.0/500 A**, 1040 1040 1120 1040 1320 1520 1100 1100 1100 1100 B min., 390 390 390 390 390 390 530 530 600 600 B max., 840 840 840 840 840 840 1120 1120 1190 1190 C, 275 275 275 250 275 275 250 250 250 250 D, 160 160 160 160 160 160 160 160 160 160 E, 300 300 300 300 300 300 350 350 350 350 F, 35 35 35 35 35 35 36 42 48 48 G, 20 20 20 20 20 20 25 30 35 35 ** Scissor dimensions TBG with large jaw capacity, lug suspension for grabs with 2.0 t and above 144
Bale grab model TBA 200-1000 The TBA bale grab transports bales of fiber, wool, fabric, paper, pressed straw and various types of shavings up to a width of 1.3 m. Bales are gripped safely yet gently, and where applicable, the clamps are lined with a soft and pliable material. The locking pawl only engages if the grab is opened without manual intervention. The standard grab is equipped with protective linings. Serrated jaws available on request. Technical data model TBA Jaw capacity Z TBA 0.2/700 *553667 200 250-700 40 TBA 0.3/900 *552080 300 450-900 42 TBA 0.5/1100 *552776 500 650-1100 45 TBA 0.75/1300 *552035 750 850-1300 62 TBA 1.0/1300 *553674 1000 850-1300 62 Dimensions model TBA TBA 0.2/700 TBA 0.3/900 TBA 0.5/1100 TBA 0.75/1300 TBA 1.0/1300 A, 890 1090 1290 1550 1550 B, 420 420 420 420 420 C, 500 500 500 500 500 D, 35 35 35 35 35 E, 20 20 20 20 20 TBA 0.2-1 t with serrated jaw 145
Rail grab with safety lock model TCR 1000-2000 The TCR rail grab transports rails, as used by railways, easily and safely. A safe grip is ensured by the lever operated safety lock. For long rails, two grabs must be attached to a spreader beam to avoid sagging. Since the rails are primarily grabbed with positive fit, it is important that the clamp stays in a vertical position during initial lift. For rails with a larger head or sidings, please inquire about customized grabs. A TCR multiple rail system is also available for the simultaneous transport of up to 12 rails. For special sizes please advise rail type and profile. Technical data model TCR TCR 1.0 *550802 1000 12.4 TCR 2.0 *551076 2000 13.9 Dimensions model TCR TCR 1.0 TCR 2.0 A*, 144 144 B, 152 163 C, 350 350 D, 90 90 E, 46 46 Ø F, 20 20 G, 25 25 * Scissor dimensions TCR 146
Inside grab model TDI 100-5000 Inside grabs are available in three versions for the handling of cylindrical and rectangular hollow bodies. The clamping jaws are available with optional steel jaws, hard manganese serrated jaws or jaws with protective lining, which are designed to grab a variety of shapes and materials. These inside grabs can be equipped with an automatic opening and closing device. Ideal especially for wire coils and hollow bodies. For inside grabs with jaws with protective lining, the inside surface of the material must be free of oil and grease. When ordering, please advise the requested version. Technical data model TDI Jaw capacity TDI 0.1/420 *551410 100 220-420 17 TDI 0.5/600 *552066 500 400-600 51 TDI 1.0/600 *553704 1000 400-600 53 TDI 2.0/800 *553711 2000 550-800 150 TDI 3.0/800 *553728 3000 550-800 175 TDI 5.0/800** *553735 5000 550-800 220 ** with hard manganese serrated jaws Dimensions model TDI TDI 0.1/420 TDI 0.5/600 TDI 1.0/600 TDI 2.0/800 TDI 3.0/800 TDI 5.0/800 A, 790 1200 1200 1400 1450 1450 B, 455 610 600 830 920 795 C, 550 800 900 1100 1000 1000 D, 80 100 100 120 160 160 E, 90 160 160 220 220 65 F, 124 151 151 G, Ø 60 Ø 92 Ø 92 83 107 107 H, 15 15 15 30 30 35 I, 22 30 30 42 42 42 TDI 147
Container lifting lugs TCU TCO Container lifting lugs model TCO and model TCU 32000-56000 These container lifting lugs are offered in a set of 4 pieces with a total weight capacity of 56 t. The lugs serve as flexible attachment points for the transport of containers. Two types are available which can be fastened to either the top of the container or laterally. TCO is vertically mounted in the hole at the top of the container. Turning the TCO 90, locks it securely in place. Transport is done with the use of a spreader beam in conjunction with wire rope, chain or textile slings making sure the load is suspended vertically. TCU is mounted laterally on the container (in the upper or the lower part) and has a springloaded bolt to prevent an accidental release. Transport is done with the use of a spreader beam in conjunction with wire rope, chain or textile slings up to the below mentioned angles from the vertical. Container transport shackle model TCO Container transport shackle model TCU Technical data model TCO and model TCU ** ** Max. angle from the vertical TCU 32 *556927 32000 19.5 50 TCU 40 *556927 40000 19.5 36 TCO 56 *556965 56000 30.1 true vertical lift ** set of 4 pieces Dimensions model TCO and model TCU TCU 32 TCU 40 TCO 56 TCO A, 152 152 123 B, 181 181 217 Ø C, 45 45 45 D, 37 37 39 E, 73 73 57 F, 75 75 101 G, 40 40 121 TCU 148
Clamps & Trolleys Beam clamp model YC 1000-10000 Trolley clamp model CTP 1000-3000 Push and geared model HTP and model HTG 500-20000 Information about beam clamps and trolleys are presented in the hoisting chapter, from page 54-63. Swivel truck trolley with low headroom and extremely short radius curve model VLHP and model VLHG 250-6000 Electric trolley model VTE-U 1000-5000 149
C-Hooks C-Hook model TCK 500-10000 Coils, rolls, rings and similar items are transported safely with the Tigrip C-Hooks. Tine length and usable height with the most frequently encountered coil sizes are listed in the table below. Other working loads, measurements, and models, such as C-Hooks with automatic balancing device, are available upon request. Illustration shows tines with 4/4 the length of the coil width (special). Technical data model TCK TCK 0.5/300 *554800 500 21 TCK 0.5/500 *552417 500 30 TCK 0.5/800 *554817 500 46 TCK 1.0/300 *554824 1000 28 TCK 1.0/500 *554831 1000 40 TCK 1.0/800 *552783 1000 95 TCK 2.0/300 *554848 2000 45 TCK 2.0/500 *551830 2000 90 TCK 2.0/800 *552615 2000 140 TCK 2.0/1000 *552479 2000 180 TCK 3.0/300 *554855 3000 68 TCK 3.0/500 *554862 3000 127 TCK 3.0/800 *552431 3000 165 TCK 3.0/1000 *554879 3000 215 TCK 5.0/500 *551298 5000 184 TCK 5.0/800 *554886 5000 238 TCK 5.0/1000 *554893 5000 286 TCK 5.0/1250 *554909 5000 364 TCK 7.5/800 *555043 7500 390 TCK 7.5/1000 *551984 7500 520 TCK 7.5/1250 *551878 7500 650 TCK 7.5/1500 *554916 7500 767 TCK 10.0/1000 *554923 10000 772 TCK 10.0/1250 *551670 10000 810 TCK 10.0/1500 *554930 10000 980 150
C-Hooks Dimensions model TCK TCK 0.5/300 TCK 0.5/500 TCK 0.5/800 TCK 1.0/300 TCK 1.0/500 TCK 1.0/800 TCK 2.0/300 TCK 2.0/500 TCK 2.0/800 TCK 2.0/1000 Coil width A, 300 500 800 300 500 800 300 500 800 1000 Usable height B, 400 400 400 450 450 450 500 500 500 500 C, 570 580 580 620 630 630 700 700 720 720 D, 60 60 60 60 60 60 75 75 75 75 E, 120 120 120 120 120 120 150 150 150 150 F, 20 20 25 25 20 30 25 30 30 20 G, 25 23 23 23 23 23 38 38 38 35 H, 20 20 25 20 25 30 25 30 30 40 I, 50 65 70 70 80 90 90 110 125 125 TCK 3.0/300 TCK 3.0/500 TCK 3.0/800 TCK 3.0/1000 TCK 5.0/500 TCK 5.0/800 TCK 5.0/1000 TCK 5.0/1250 TCK 7.5/800 TCK 7.5/1000 Coil width A, 300 500 800 1000 500 800 1000 1250 800 1000 Usable height B, 500 500 500 500 550 550 550 550 600 600 C, 700 700 720 720 800 800 820 820 900 900 D, 75 75 75 75 100 100 100 100 110 110 E, 150 150 150 150 200 200 200 200 220 220 F, 30 20 25 20 25 30 30 30 35 35 G, 38 40 40 40 45 45 45 45 50 50 H, 30 30 40 40 40 50 50 50 50 60 I, 105 125 140 155 145 160 180 200 200 200 TCK 7.5/1250 TCK 7.5/1500 TCK 10.0/1000 TCK 10.0/1250 TCK 10.0/1500 Coil width A, 1250 1500 1000 1250 1500 Usable height B, 600 600 650 650 650 C, 900 920 980 1000 1000 D, 110 110 130 130 130 E, 220 220 250 250 250 F, 35 35 40 45 45 G, 45 50 50 55 55 H, 60 70 70 70 80 I, 220 220 220 240 240 TCK Standard model has tines 3/4 the length of the coil width as shown in drawing. 151
C-Hooks Coil hook model TCS 500-3000 The TCS coil hook is an universal C-Hook. Due to its tipping feature, it can lift or lower the coil, whether the coil is lying flat or is in an upright position. With this tipping device, the coil is tipped safely through 90. The slow and safe movement of the tipping device ensures a continuous flowing movement when lifting or lowering the coil. At the same time, the tipping device serves the purpose of preventing accidental slipping of the load during transport. Other sizes and models available upon request. Technical data model TCS TCS 0.5/120 *554947 500 6.9 TCS 0.5/200 *552257 500 9.6 TCS 1.0/200 *552264 1000 15.4 TCS 1.0/300 *552875 1000 20.0 TCS 2.0/200 *551977 2000 24.8 TCS 2.0/300 *551908 2000 33.4 TCS 3.0/200 *552011 3000 45.0 TCS 3.0/300 *552714 3000 51.0 TCS Dimensions model TCS TCS 0.5/120 TCS 0.5/200 TCS 1.0/200 TCS 1.0/300 TCS 2.0/200 TCS 2.0/300 TCS 3.0/200 TCS 3.0/300 Coil width A min, 50 100 100 200 100 200 100 200 Coil width A max., 120 200 200 300 200 300 200 300 B, 10 10 10 10 12 12 15 15 C, 60 60 80 80 90 90 100 100 D, 330 330 460 460 420 420 610 610 E, 470 470 600 600 600 600 820 820 F, 20 20 20 20 30 30 40 40 G, 110 110 110 110 135 135 160 160 H, 60 60 60 60 75 75 90 90 K, 50 50 60 60 80 80 100 100 L, 45 50 65 70 85 95 100 110 T, 20 20 25 25 30 30 35 35 Ø I, 220 300 300 400 300 400 300 400 152
Barrel grabs & Crate grabs Barrel grab for transport of upright barrels model TFA 300 This unit grabs upright barrels and sets them down in the same position. Although the clamping jaws are fitted with a hard rubber lining to provide a friction hold, it is the positive fit on the rim that provides extra safety. This additional feature is indispensable if the surface of the barrels is stained with oil or grease. The clamping jaws fitted with a protective lining enable the non-marring and secure grab around the circumference of the barrel. The clamp is suitable for standard type barrels. Technical data model TFA Jaw capacity diameter TFA 0.3/600 *557009 300 400-600 57 Dimensions model TFA TFA 0.3/600 A, 600 B, 1040 C, 950 Ø D, 90 E, 34 F, 15 G, 200 H, 400 I, 400 For barrels according to DIN 6643. TFA 153
Barrel grabs & Crate grabs Barrel grab with tipping device model TFA-D 300 The grab with tipping device is suited to lift, transport as well as tipping and emptying the barrel. In order to tip the barrel easily, it must be picked up at the correct center of gravity. For barrels according to DIN 6643. Technical data model TFA D Jaw capacity diameter TFA 0.3/600 D *557917 300 400-600 83 Dimensions model TFA D TFA 0.3/600 D A, 600 B, 1150 C, 1525 Ø D, 90 E, 34 F, 15 G, 200 H, 400 TFA-D 154
Barrel grabs & Crate grabs Barrel grab model TFA 0.35/700 R and model TFA 0.35/700 TR 350 These barrel grabs are designed for transport of steel barrels. The clamping jaws press securely with a positive fit underneath the rim of the barrel. TFA 0.35/700 R TFA 0.35/700 TR TFA 0.35/700 TR is a combination unit for the transport of barrels that can be used with either an overhead crane or forklift. Technical data model TFA R/TR Jaw capacity diameter TFA 0.35/700 R *551014 350 420-700 5.7 TFA 0.35/700 TR *551472 350 420-700 9.2 s TFA-R and TFA-TR 155
Barrel grabs & Crate grabs Barrel rim clamp model TFRK 500 The TFRK barrel rim clamp can be used individually, as a pair, or as a multi-legged chain sling. The clamp grabs under the rim of the barrel. A springloaded cam prevents the accidental opening of the clamp. For barrels according to DIN 6643. Technical data model TFRK TFRK *556415 500 1.5 Dimensions model TFRK TFRK 0.5 A, 152 B, 150 C, 127 D, 30 E, 21 F, 41 G, 17 Ø H, 40 156
Barrel grabs & Crate grabs Barrel clamp model TFK 500 Its light weight and small overall design makes it ideal for lifting barrels where access or space is limited. The center of gravity of the barrel is the lifting point during transport. For barrels according to DIN 6643. Technical data model TFK TFK 0.5 *556071 500 7.3 Dimensions model TFK TFK 0.5 A, 479 B, 350 C, 410 D, 300 Ø E, 50 TFK 157
Barrel grabs & Crate grabs Crate grab with tipping device model TKA/d 150 The crate grab with tipping device is an absolutely safe unit, which not only securely transports stacking boxes, but can empty them in mid-air as well. A safety lever system prevents the accidental opening of the grab. The clamping jaws tightly grab under the rim of the crate without damaging the crate. To engage the tipping motion in order to empty the crate, the safety lock must be manually unlocked. The tipping motion is limited to 100. This prevents the crate from flipping completely over while emptying, thereby reducing the risk of injury. Option Grabs for other sizes of crates are available upon request. Please provide the crate dimensions or a sample crate when ordering. Technical data model TKA/d TKA 0.15/330d *551519 150 25.8 TKA 0.15/480d *552103 150 26.0 Dimensions model TKA/d TKA 0.15/330d TKA 0.15/480d TKA.../...d A, 200-300 300 B, 315-330 470-480 L, 465-540 550-660 158
Barrel grabs & Crate grabs Crate grab model TKA a/i 250 The easy-handling crate grab, which grabs on the side plates or the front sides of the crate, transports crates safely and without damaging them. The moveable jaws press the edge of the crate gently against the outside grab support rails. Stacking boxes made of steel or plastic will not get deformed. After the box has been set down, the safety device holds the grab open. When lifting the crate and grabbing the support rails, the safety device must be manually pulled back until it lies over the safety bolt. With further lifting, the jaws grab under the outer top edge of the crate and lift it up safely. The crate grab is available as an external or internal operating grab. TKA.../...a external operating Please provide the crate dimensions or a sample crate when ordering. TKA.../...i internal operating TKA.../...i internal operating Technical data model TKA a/i Jaw capacity TKA 0.25/320a *558082 9.3 250 320 TKA 0.25/480a *558044 9.3 250 480 TKA 0.25/600a *558099 9.3 250 600 TKA 0.25/320i *558051 8.5 250 320 TKA 0.25/480i *558068 8.5 250 480 TKA 0.25/600i *558075 8.5 250 600 TKA.../...a external operating TKA.../...i internal operating 159
Lifting gear for underground construction For concrete pipes according to DIN 4034. Lifting gear for concrete pipe up to a diameter of Ø 3000 available upon request. Concrete pipe lifting gear model BTG 1500-3000 Lifting gear for the vertical transport of concrete pipe and culverts must be very versatile. Most important, it must be absolutely safe and easy to handle under even the harshest conditions. The Tigrip concrete pipe lifting gear meets all these requirements. It is a three-legged lifting system for the safe and non-marring transport of concrete pipes up to a diameter of Ø 2000 and a load of up to 3 t. The jaw capacity is designed for concrete pipe thicknesses from 40-220. Attachment and removal of the clamps can be done easily due to the handles that have been incorporated into each clamp. Features Solid construction Safety factor 4:1 Simple and safe handling Large jaw capacity For the toughest operating conditions Lightweight design Service-friendly Technical data model BTG ** Jaw capacity Z Mouth depth E Pressure line F BTG 1.5/120 *550147 1500 40-120 165 100 35 BTG 3.0/180 TM-N *551199 3000 50-180 245 175 90 BTG 3.0/220 TM-N *550819 3000 90-220 245 175 94 ** Per lifting gear three-legged Dimensions model BTG BTG 1.5/120 BTG 3.0/180 TM-N BTG 3.0/220 TM-N A, 135 180 180 B, 75 100 100 Ø C, 18 26 26 D, 180 310 310 BTG 160
Lifting gear for underground construction Trench shield grab model TCP 1500-5500 The TCP grab is suitable for vertical positioning and transportation of trench shields. Once the grab is set onto the trench shield, a springloaded bolt locks itself into the hole of the shield. Releasing the bolt is done with the 15 m pull cord attached to the grab. Technical data model TCP TCP 1.5 *555807 1500 12.2 TCP 3.0 *555791 3000 19.5 TCP 5.5 *555784 5500 26.7 Dimensions model TCP TCP 1.5 TCP 3.0 TCP 5.5 A, 207 226 269 B, 488 517 575 C, 218 218 218 D, 90 100 120 E, 18 24 24 Ø F, 20 24 30 G, 180 180 180 Ø H, 50 63 89 TCP 161
Lifting gear for underground construction Trench shield clamp model TPP 3000-12000 The TPP trench shield clamp is similar to a regular plate clamp in its construction but has a much deeper jaw. The compact construction combined with a high capacity makes it ideal for pulling trench shields out of the ground. A safety lock prevents the accidental opening of the clamp. Technical data model TPP Jaw capacity TPP 3 *556255 3000 0-20 16.0 TPP 8 *556217 8000 0-30 27.8 TPP 12 *556231 12000 0-30 53.0 Dimensions model TPP TPP 3 TPP 8 TPP 12 A, 224 294 361 B, 325 445 486 Ø C, 20 30 40 D, 88 109 145 E, 147 194 190 F, 25 42 41 G, 123 146 167 H, 60 72 90 I, 20 25 30 J, 18 26 32 TPP 162
Lifting gear for underground construction Pipe hook model TRO 2000-10000 The pipe hooks are used in pairs for the safe transport of pipes. Scope of delivery The shackles are included with the hooks. Technical data model TRO for 60-90 chain - top angle ** ** TRO 2/90 *556729 2000 3.1 TRO 4/90 *556743 4000 5.6 TRO 6/90 *556767 6000 10.5 TRO 8/90 *556781 8000 17.8 TRO 10/90 *556804 10000 22.0 ** Per pair Dimensions model TRO for 60-90 chain - top angle TRO 2/90 TRO 4/90 TRO 6/90 TRO 8/90 TRO 10/90 t, 20 30 30 40 40 A, 0-40 0-50 0-60 0-70 0-80 B, 35 40 51 55 69 C, 40 48 62 67 80 D, 62 77 90 105 115 E, 62 77 90 105 115 F, 116 142 173 190 221 Ø G, 16.3 24.3 24.3 30.3 30.3 H, 47.6 72.2 72.2 95.3 95.3 Ø I, 12.7 19 19 25.4 25.4 J, 30.2 44.5 44.5 58.7 58.7 Technical data model TRO for 90-120 chain - top angle ** ** TRO 2/120 *556828 2000 3.5 TRO 4/120 *556842 4000 8.8 TRO 6/120 *556866 6000 14.9 TRO 8/120 *556880 8000 18.6 TRO 10/120 *556903 10000 23.0 ** Per pair Dimensions model TRO for 90-120 chain - top angle TRO 2/120 TRO 4/120 TRO 6/120 TRO 8/120 TRO 10/120 TRO t, 20 30 40 40 50 A, 0-30 10-40 20-50 30-65 30-75 B, 34 39 43 54 60 C, 40 50 55 65 70 D, 82 95 106 119 143 E, 75 80 95 100 125 F, 106 131 153 185 208 Ø G, 16.3 24.3 30.3 30.3 36.3 H, 30.2 44.5 58.7 58.7 73 Ø I, 12.7 19 25.4 25.4 31.8 J, 47.6 72.2 95.3 95.3 117 163
Clamps Clamps for cable drums model TKB 5000 Specifically designed for the transport of cable drums, these clamps are used in pairs together with a twolegged chain sling. By the spreading of the clamp, it locks inside the drum. The clamps can be held in place by a locking lever. Easy handling, light-weight design, and the size of the clamp contribute to a safe transport of all types of cable drums. Various sizes are available upon request. Please supply dimensions C and D. Technical data model TKB ** TKB *556606 5000 11 ** Per pair Dimensions model TKB TKB A, 277 B, 277 Ø C, 82 D, 85 Ø E, 50 TKB 164
Tine hooks Tine hook model TZH 1500-10000 For fastening hoisting equipment and loads to forklift tines. The TZH are pushed onto the forklift tines and are fastened with two spindles. The pivoting as well as swivelling hook with safety latch ensures safety while lifting. Attention must be paid to the working load limit of the single forklift tines. Technical data model TZH TZH 1.5/150 *557566 1500 7.2 TZH 3.0/150 *557580 3000 10.8 TZH 5.0/150 *557603 5000 17.3 TZH 5.0/200 *557627 5000 24.7 TZH 10.0/200 *557641 10000 43.0 Dimensions model TZH TZH 1.5/150 TZH 3.0/150 TZH 5.0/150 TZH 5.0/200 TZH 10.0/200 A, 100 100 100 150 150 B, 150 150 150 200 200 Cmin., 310 350 350 440 440 Cmax., 360 400 400 490 490 D, 260 270 295 320 420 E, 74 74 74 94 94 F, 120 120 120 180 180 G, 25 28 34 34 45 TZH Swivel hooks, pivoting and swivelling 165
Spreader beams Customised models on page 168-169. Spreader beam, non-adjustable model -E 1000-10000 Tigrip spreader beams are the practical and safe choice for either long material to prevent sagging and shifting, or for loads where the weight has to be carefully distributed or suspended from several points. The extensive standard program offers a wide variety of capacities, working widths, adjustable ranges and hooks for coon applications. This heavy-duty and cost-effective standard type is complemented by various customized designs. These may be spreader beams with hooks for plate material, or with C-hooks, crane forks, or grabs for bulky and long materials. Special designs with laterally fixed hooks are fitted with slings to pick up rolls, pipes and similar objects. Also available are the so-called star spreader beams for picking up cylindrical materials or spreader beams with side hooks and 4-point support which share the easy operation, reliability and safety of all Tigrip spreader beams. -E without adjustments 166
Spreader beams Technical data model -E Working width Hook mouth 1.0/1000 E *552905 1000 1000 23 23 2.0/1000 E *554534 2000 1000 23 25 3.0/1000 E *552813 3000 1000 30 28 5.0/1000 E *554541 5000 1000 38 41 7.5/1000 E *554558 7500 1000 42 50 10.0/1000 E *554565 10000 1000 42 61 1.0/1500 E *552851 1000 1500 23 31 2.0/1500 E *554572 2000 1500 23 33 3.0/1500 E *552028 3000 1500 30 41 5.0/1500 E *552172 5000 1500 38 64 7.5/1500 E *554589 7500 1500 42 74 10.0/1500 E *554596 10000 1500 42 90 1.0/2500 E *554602 1000 2500 23 46 2.0/2500 E *552769 2000 2500 23 69 3.0/2500 E *552202 3000 2500 30 88 5.0/2500 E *552493 5000 2500 38 106 7.5/2500 E *554619 7500 2500 42 148 10.0/2500 E *554626 10000 2500 42 181 1.0/3500 E *554633 1000 3500 23 77 2.0/3500 E *554640 2000 3500 23 118 3.0/3500 E *552592 3000 3500 30 138 5.0/3500 E *554657 5000 3500 38 167 7.5/3500 E *554664 7500 3500 42 235 10.0/3500 E *554671 10000 3500 42 272 1.0/5000 E *554688 1000 5000 23 163 2.0/5000 E *552523 2000 5000 23 189 3.0/5000 E *554695 3000 5000 30 223 5.0/5000 E *554701 5000 5000 38 295 7.5/5000 E *554718 7500 5000 42 372 10.0/5000 E *554725 10000 5000 42 478 Dimensions model -E 1.0/1000 E 2.0/1000 E 3.0/1000 E 5.0/1000 E 7.5/1000 E 10.0/1000 E 1.0/1500 E 2.0/1500 E 3.0/1500 E 5.0/1500 E B, 375 400 470 585 690 770 375 400 490 605 C, 110 135 160 180 200 260 110 135 160 180 D, 25 30 35 40 60 70 25 30 35 40 E, 60 75 90 100 130 130 60 75 90 100 7.5/1500 E 10.0/1500 E 1.0/2500 E 2.0/2500 E 3.0/2500 E 5.0/2500 E 7.5/2500 E 10.0/2500 E 1.0/3500 E 2.0/3500 E B, 710 790 375 440 530 625 750 830 405 460 C, 200 260 110 135 160 180 200 260 110 135 D, 60 70 25 30 35 40 60 70 25 30 E, 130 130 60 75 90 100 130 130 60 75 3.0/3500 E 5.0/3500 E 7.5/3500 E 10.0/3500 E 1.0/5000 E 2.0/5000 E 3.0/5000 E 5.0/5000 E 7.5/5000 E 10.0/5000 E B, 550 665 770 850 445 480 570 685 790 890 C, 160 180 200 260 110 135 160 180 200 260 D, 35 40 60 70 25 30 35 40 60 70 E, 90 100 130 130 60 75 90 100 130 130 167
Spreader beams Spreader beam, adjustable model 1000-25000 Technical data model Working width Z Hook mouth 1.0/1500 *552646 1000 700-1500 18 40 2.0/1500 *552295 2000 700-1500 18 41 3.0/1500 *553988 3000 700-1500 21 53 5.0/1500 *551281 5000 700-1500 23 79 7.5/1500 *553995 7500 700-1500 32 98 10.0/1500 *552219 10000 700-1500 32 117 12.5/1500 *554008 12500 700-1500 40 116 15.0/1500 *554015 15000 700-1500 40 137 20.0/1500 *554022 20000 700-1500 50 180 25.0/1500 *554039 25000 700-1500 50 226 1.0/2500 *554046 1000 1500-2500 18 58 2.0/2500 *552158 2000 1500-2500 18 84 3.0/2500 *552448 3000 1500-2500 21 105 5.0/2500 *552424 5000 1500-2500 23 127 7.5/2500 *554053 7500 1500-2500 32 178 10.0/2500 *554060 10000 1500-2500 32 215 12.5/2500 *554077 12500 1500-2500 40 198 15.0/2500 *554084 15000 1500-2500 40 237 20.0/2500 *554091 20000 1500-2500 50 287 25.0/2500 *554107 25000 1500-2500 50 342 1.0/3500 *552684 1000 1700-3500 18 95 2.0/3500 *554114 2000 1700-3500 18 137 3.0/3500 *554121 3000 1700-3500 21 162 5.0/3500 *554138 5000 1700-3500 23 228 7.5/3500 *554145 7500 1700-3500 32 278 10.0/3500 *554152 10000 1700-3500 32 317 12.5/3500 *554169 12500 1700-3500 40 295 15.0/3500 *551403 15000 1700-3500 40 340 20.0/3500 *554176 20000 1700-3500 50 451 25.0/3500 *554183 25000 1700-3500 50 512 1.0/5000 *554367 1000 2000-5000 18 190 2.0/5000 *554374 2000 2000-5000 18 219 3.0/5000 *554381 3000 2000-5000 21 260 5.0/5000 *554398 5000 2000-5000 23 372 7.5/5000 *554404 7500 2000-5000 32 423 10.0/5000 *554411 10000 2000-5000 32 531 12.5/5000 *554428 12500 2000-5000 40 449 15.0/5000 *554435 15000 2000-5000 40 568 20.0/5000 *554442 20000 2000-5000 50 691 1.0/8000 *554459 1000 3000-8000 18 342 2.0/8000 *554466 2000 3000-8000 18 458 3.0/8000 *554473 3000 3000-8000 21 547 5.0/8000 *554480 5000 3000-8000 23 788 7.5/8000 *554497 7500 3000-8000 32 883 10.0/8000 *554503 10000 3000-8000 32 1319 12.5/8000 *554510 12500 3000-8000 40 979 15.0/8000 *554527 15000 3000-8000 40 1046 168
Spreader beams Dimensions model 1.0/1500 2.0/1500 3.0/1500 5.0/1500 7.5/1500 10.0/1500 12.5/1500 15.0/1500 20.0/1500 25.0/1500 B, 410 440 540 625 710 805 835 880 990 1200 C, 110 135 160 180 200 260 260 260 260 300 D, 25 30 35 40 60 70 75 85 90 100 E, 60 75 90 100 130 130 140 140 160 160 1.0/2500 2.0/2500 3.0/2500 5.0/2500 7.5/2500 10.0/2500 12.5/2500 15.0/2500 20.0/2500 25.0/2500 B, 410 475 580 645 755 850 885 925 1030 1225 C, 110 135 160 180 200 260 260 260 260 300 D, 25 30 35 40 60 70 75 85 90 100 E, 60 75 90 100 130 130 140 140 160 160 1.0/3500 2.0/3500 3.0/3500 5.0/3500 7.5/3500 10.0/3500 12.5/3500 15.0/3500 20.0/3500 25.0/3500 B, 410 500 605 685 780 875 905 950 1085 1270 C, 110 135 160 180 200 260 260 260 260 300 D, 25 30 35 40 60 70 75 85 90 100 E, 60 75 90 100 130 130 140 140 160 160 1.0/5000 2.0/5000 3.0/5000 5.0/5000 7.5/5000 10.0/5000 12.5/5000 15.0/5000 20.0/5000 1.0/8000 B, 465 520 625 710 800 920 950 995 1125 485 C, 110 135 160 180 200 260 260 260 260 110 D, 25 30 35 40 60 70 75 85 90 25 E, 60 75 90 100 130 130 140 140 160 60 2.0/8000 3.0/8000 5.0/8000 7.5/8000 10.0/8000 12.5/8000 15.0/8000 B, 560 670 755 865 980 1015 1055 C, 135 160 180 200 260 260 260 D, 30 35 40 60 70 75 85 E, 75 90 100 130 130 140 140 with adjustable hooks 169
Spreader beams Customized spreader beams Quick overview of our extensive program Spreader beams are required in the most different versions and designs. The illustrations given on these pages reflect a brief overview of the multitude of various spreader beam versions. Chain suspension adjustable hooks Yoke suspension long hook Double suspension Double suspension Single or double hook according to DIN 15401 and 15402 with single hook double hook swivel hook or safety eye hook 170
Spreader beams Standard spreader beams Hooks with safety latch Hooks with safety latch adjustable Safety eye hooks pivoting with swivel hooks swivelling and pivoting with long hooks fixed or adjustable Safety eye hooks pivoting and adjustable with swivel hooks swivelling, pivoting and adjustable Spreader beams with side hooks Safety eye hooks pivoting fixed Swivel hooks swivelling, pivoting and adjustable adjustable 171
Spreader beams Spreader beam for box pallets model 1000-3000 Box pallets with DIN 15155 specifications, are usually moved around with a forklift, but are so sturdy that they can be picked up and transported with a spreader beam grab and an overhead crane hooked up to the top of the box pallet s frame. Thanks to these spreader beams, the shipping and receiving area is no longer entirely dependent on floorlevel material handling equipment such as forklifts. The version designed for the individual transport of box pallets is equipped with two fixed yokes and two pivoted ones, interconnected with a control bar. The load tackling gear is fixed and unfixed by only one person. When using these spreader beams, it is important that the hooks be fastened only to the top frame of the box pallets. Technical data model 1.0/1240-810 *551595 1000 38 2.0/1240-810 *551236 2000 61 3.0/1240-810 *553742 3000 80 Dimensions model 1.0/1240-810 2.0/1240-810 3.0/1240-810 A, 1175 1175 1175 B, 600 600 600 C, 410 495 520 D, 195 215 215 E, 125 180 205 F, 100 150 170 G, 80 100 130 H, 28 30 40 I, 15 20 25 172
Spreader beams Spreader beam for Big-Bags model TTB 1000-2000 This four-point spreader beam in a fixed frame construction with weld-on hooks and safety latch is designed for lifting and transporting of Big-Bags. Technical data model TTB Working width Z TTB 1.0/1090-1090 *556293 1000 750-800 27 TTB 1.0/1320-1320 *556316 1000 900-970 33 TTB 2.0/1090-1090 *556330 2000 750-800 42 TTB 2.0/1320-1320 *556354 2000 900-970 44 Dimensions model TTB TTB 1.0/1090-1090 TTB 1.0/1320-1320 TTB 2.0/1090-1090 TTB 2.0/1320-1320 B, 210 210 240 240 C, 60 60 75 75 D, 110 110 135 135 TTB 173
Crane forks For the transport of loads above persons (e.g. on construction sites) appropriate security measures against falling loads or parts must be taken. Crane forks model TKG vhs 200-5000 These crane forks are equipped with adjustable tines, height adjustability and an automatic balancing system. Crane forks with automatic balancing* tend to point their tines upward when being transported. This prevents the load from unintentionally slipping off the tines. The shackle is movable and runs on a track depending on the load. The automatic balancing engages by a pressurized gas spring once the forks are loaded. The load will always be in the center of gravity of the forks, ensuring a safe transport. *The automatic balancing system requires a minimum load of 20 % of the crane forks working load limit. Features Safety factor 4:1. Maintenance-free. Highly visible safety colour. For the transport of rings or coils, the fork tines are simply pushed together. Easily adjustable tines for all pallet sizes. Scope of delivery Chain for load securing. The load must not exceed the fork length. Technical data model TKG vhs TKG 1.0 vhs *552233 200-1000 128 TKG 1.5 vhs *551113 300-1500 158 TKG 2.0 vhs *550666 400-2000 203 TKG 3.0 vhs *551090 600-3000 260 TKG 5.0 vhs *554794 1000-5000 413 Dimensions model TKG vhs TKG 1.0 vhs TKG 1.5 vhs TKG 2.0 vhs TKG 3.0 vhs TKG 5.0 vhs Adjustment of tines A, 350-900 350-900 400-900 450-900 500-1000 Usable height B, 1100-1600 1300-2000 1300-2000 1300-2000 1300-2000 Length of tines C, 1000 1000 1000 1000 1000 Section of tines D, 100 x 30 100 x 40 120 x 40 120 x 50 150 x 60 Overall height E, 1420-1920 1650-2350 1655-2355 1720-2420 1710-2410 174
Crane forks Crane forks model TKG vh 1000-5000 These crane forks are equipped with adjustable tines and height adjustability. The balancing system engages when the shackle is manually hooked into the appropriate notch. Features Safety factor 4:1. Maintenance-free. Highly visible safety colour. For the transport of rings or coils, the fork tines are simply pushed together. Easily adjustable tines for all pallet sizes. Scope of delivery Chain for load securing. The load must not exceed the fork length. Technical data model TKG vh TKG 1.0 vh *552370 1000 128 TKG 1.5 vh *551052 1500 148 TKG 2.0 vh *554756 2000 193 TKG 3.0 vh *551564 3000 248 TKG 5.0 vh *554763 5000 388 Dimensions model TKG vh TKG 1.0 vh TKG 1.5 vh TKG 2.0 vh TKG 3.0 vh TKG 5.0 vh Adjustment of tines A, 350-900 350-900 400-900 450-900 500-1000 Usable height B, 1100-1600 1300-2000 1300-2000 1300-2000 1300-2000 Length of tines C, 1000 1000 1000 1000 1000 Section of tines D, 100 x 30 100 x 40 120 x 40 120 x 50 150 x 60 Overall height E, 1390-1890 1600-2300 1640-2340 1670-2370 1700-2400 175
Tigrip Crane Weighers Crane weighers Measuring range 0-12 t The crane weighers TKA and TWF are compact measuring devices for the weighing of loads. Use appropriate attachments like grade 8 forgings between the hook of the hoist or crane, the crane weigher and the load. The crane weighers have a liquid crystal display (LCD), which can tare as well as show either the gross or the net load. It also indicates the overload protection at 110 % of the gross weight and the status of the battery. - with digital display model TKA Features High accuracy Lightweight design Easy-to-read display Easy to use Excellent quality Robust design Housing swivelling 180 Retains the peak value to memory Rechargeable, with integrated storage battery - with digital display and radio control model TWF The crane weigher can be operated by radio control. The displayed values can be taken off the remote control device and can be transferred to a PC. Scope of delivery Crane weigher Battery charger (3 V, 700 ma) Carrying case Test certificate Features The concept corresponds to model TKA. Radio control RS 232 interface Option PC cable User software Scope of delivery Crane weigher Battery charger (3 V, 700 ma) Remote control with display Carrying case Test certificate 176
Tigrip Crane Weighers Technical data model TKA and model TWF TKA 1.0 TWF 1.0 TKA 2.0 TWF 2.0 TKA 3.2 TWF 3.2 TKA 5.0 TWF 5.0 TKA 8.0 TWF 8.0 TKA 12.0 TWF 12.0 model TKA model TWF Measuring range, t Nominal load, t Limit load, t Breaking load, t with lifting accessories, Accuracy Resolution step, Operation time, approx.* Temperature range (operation) Temperature range (storage) *557368 *557382 *557405 *557429 *557443 *558365 *558240 *558259 *558266 *558273 *558280 *558372 0-1.0 0-2.0 0-3.2 0-5.0 0-8.0 0-12.0 1.0 2.0 3.2 5.0 8.0 12.0 1.1 2.2 3.5 5.5 8.8 13.2 4 8 13 20 32 48 3.0 3.6 5.9 7.3 10.5 19.8 0.1%.. of the nominal load 0.5 1 1 1 2 5 200 h at 20 C 10 C up to + 50 C 20 C up to + 70 C Protection IP 54 Display Height 20.5, 4 ½ digits Tare range 100 % of final value Overload warning Overload warning with an exceedance of 110 % * with one battery charging Dimensions model TKA and model TWF TKA 1.0 TWF 1.0 TKA 2.0 TWF 2.0 TKA 3.2 TWF 3.2 TKA 5.0 TWF 5.0 TKA 8.0 TWF 8.0 TKA 12.0 TWF 12.0 A, 395 423 502 585 671 820 B, 362 385 455 528 602 725 C, 60 60 75 90 100 140 D, 110 110 135 160 180 260 E, 13 16 18 22 26 35 F, 20 25 32 40 49 45 G, 70 81 103 126 152 190 H, 134 142 154 162 172 190 TKA 177
Tigrip Crane Weighers Load indicator Measuring range 0-100 t The TIGRIP load indicator is a mechanical measuring instrument with electronic display. On account of its flexibility the TIGRIP load indicator has universal applications. Whether used as a conventional crane weigher or to measure forces, it is the economical choice for various applications. It can be used in conjunction with shackles and hooks. The load indicator is provided with liquid crystal display (LCD) which can tare as well as show either the gross or the net load. It also indicates the overload protection at 110 % of the gross weight and the status of the battery. - with digital display model TKZ Features High accuracy Lightweight design Easy-to-read display Easy to use Excellent quality Robust design Retains the peak value to memory Rechargeable, with integrated storage battery Scope of delivery Load indicator Battery charger (3 V, 700 ma) Carrying case Test certificate Without shackles and hooks - with digital display and radio control model TZF The load indicator can be operated via radio control. The displayed values can be taken off the remote control device and can be transmitted to a PC. Features The concept corresponds to model TKZ. Radio control RS 232 interface Option PC cable User software Scope of delivery Load indicator Battery charger (3 V, 700 ma) Remote control with display Carrying case Test certificate Without shackles and hooks 178
Tigrip Crane Weighers Technical data model TKZ and model TZF TKZ 2.5 TZF 2.5 TKZ 5.0 TZF 5.0 TKZ 10.0 TZF 10.0 TKZ 20.0 TZF 20.0 TKZ 35.0 TZF 35.0 TKZ 50.0 TZF 50.0 TKZ 100.0 TZF 100.0 model TKZ model TKZ shackles model TKZ hooks model TZF model TZF shackles model TZF hooks Measuring range, t Nominal load, t Limit load, t Breaking load, t, *557467 *453653 *557665 *558105 *453653 *557665 0-2.5 2.5 2.75 10 2.8 *557481 *453660 *557689 *558112 *456722 *557689 0-5.0 5 5.5 20 3.4 *550116 *453714 *551311 *558129 *453714 *551311 0-10.0 10 11 40 4.4 *550093 *453714 *551007 *558136 *453714 *551007 0-20.0 20 22 80 7.6 *550444 *453738 *552226 *558143 *453738 *552226 0-35.0 35 38.5 140 10.0 *550369 *453745 *555050 *558150 *453745 *555050 0-50.0 50 55 200 25.0 *557504 *456746 *558167 0-100.0 100 110 400 41.0 Accuracy 0.2 % of the nominal load Resolution step, Operation time, approx.* 1 1 10 10 200 h at 20 C 10 10 50 Temperature range (operation) 10 C up to +50 C Temperature range (storage) 20 C up to +70 C Protection IP 54 Display Height 20.5, 4 ½ digits Tare range 100 % of final value Overload warning Overload warning with an exceedance of 110 % * with one battery charging Dimensions model TKZ and model TZF TKZ 2.5 TZF 2.5 TKZ 5.0 TZF 5.0 TKZ 10.0 TZF 10.0 TKZ 20.0 TZF 20.0 TKZ 35.0 TZF 35.0 TKZ 50.0 TZF 50.0 TKZ 100.0 TZF 100.0 A, 247 250 325 378 405 450 640 B, 118 118 118 141 156 180 260 Ø C, 22 27 48 55 64 76 100 D, 179 180 213 233 245 264 380 E, 26 22 32 45 48 55 80 F, 75 60 106 133 146 161 270 G, 47 47 47 57 70 80 99 H, 24 31 I, 8 8 8 1 1 1 1 J, 610 610 690 780 1000 1170 K, 34 50 105 92 130 140 300 L, 38 44 95 95 114 132 238 Ø M, 16 19 35 35 44 51 89 N, 25 32 50 70 110 115 O, 23 37 63 80 123 132 P, 17 28 44 57 90 97 Q, 315 315 535 562 665 730 1240 Left: Load indicator model TKZ from 2.5-5.0 t Right: Load indicator model TKZ from 10 t Load indicator with shackle Load indicator with hook 179