1.Blade server Blade Chasis Specification Blade Chassis Form Factor 6U-10U rack mountable Chasis to House at least 6 or more Blade Servers Chasis Should be configured with 6 blades Network Redundancy I/O Connectivity Blade Compatibility KVM Support Optical Drive Support L2 Switch Support Supply Cooling Modules Alert Management System management Supporting Software Efficiency Dual end to end redundant Network connectivity for each blade Each blade should have dual redundant connectivity for from the supplies through the midplane Dual Redundant I/O Connectivity to each blade server Should accommodate Intel, AMD/RISC/EPIC CPU Blades in the same Chassis At least one IP Based KVM Switch or more in the chassis The Chassis should have At least one DVD ROM drive or better which can be used by all the blade servers The optical drive should be hot swappable 2 redundant 1GB Ethernet switch to be provided in the chassis with Layer 2 features Hotswap and redundant supplies should be provided with full redundancy and all power modules should be fully populated Hot Swap and redundant cooling modules and all modules should be fully populated Pre failure alerts and error identification on Hard Disks, processor, memory, power Supplies, fans/blowers, switch modules, KVM management module should be provided System management and deployment tools to aid configuring the Blade Servers and OS Deployment Software for Vulnerability assessment The Blade servers should have dual connectors on it to be connected to the midplane so as to provide dual path for I/O,N/W and power to each server for redundancy Added advantage will be given to the most power efficient and quiter product Blade Server Specification Specification for Blades - 6 numbers No Item Specifications 1 CPU 1 x Intel Xeon Quad Core E5-2603 80W 1.8GHz 2 Cache L3 10 MB of L3 Cache 3 Chipset Intel Chipset 4 Memory 8GB Registered DDR-3 ECC Memory Upgradeable to 96 GB 5 Active Memory protection Advanced Chipkill ECC memory protection support, memory mirroring and memory sparing 6 SCSI Controllers Integrated Hardware Raid Controller to supports Hardware Raid 0,1 7 Disk Drives 2 x 300GB 2.5in SFF Slim-HS 10K 6Gbps SAS HDD
8 Graphics Controller 16MB SDRAM 9 Ethernet Adapter Server should be configured with four number of 1Gbps ethernet ports 10 Fiber Channel/SAS HBA Connectivity Dual port SAS HBA for connecting to Internal/External Storage 11 I/O Expansions 2 x8 PCIe 12 Supply From the Blade Chassis via Dual Redundant Connectors 13 Warranty 3 Years Onsite Comprehensive Warranty 14 Form Factor Full Height Blade Servers 15 Failure Alerting Mechanism 16 Blade Form Factor 17 18 Systems management capabilities Server Management Software The server should be able to alert impending failures on maximum number of components. The components covered under alerting mechanism should at least include Processor, memory, HDDs and expansion cards Full Height Blade Server with Dual Redundant I/O and Connectors Server should support systems management capabilities like Web-based out-of-band control SSL and LDAP Support Serial Over LAN IPMI over LAN Windows blue screen capture Should support remote CD and Virtual floppy Automatic Service Restart High-speed remote redirection of PCI video, keyboard and mouse NMI/SMI detection and generation Highly secure remote power on/off System reset control Server should be supplied with OEM Server Management software free of cost with features like Should be able to discover systems and other resources in a heterogeneous environment and Collect inventory data about hardware and software that is currently installed on systems Should be able to view and manage the status, problems and events for discovered systems Should be able to determine the health, compliance, and performance of managed systems by viewing detailed information about the problems by inspecting the event log Capable of automatically send the notifications for hardware events or when thresholds are exceeded Capable of doing configuration management of other systems by Initially configuring one or more systems (hardware and operating systems). Automatically configure newly discovered systems
19 OS Support Should have feature like update manager for detecting and viewing out-of-date systems and also get a notification when systems are in need of updates and which updates are needed. Download, distribute and install available and requisite updates Should be able to do the graphical remote control tools including VNC, RDP, and web-based remote control for AMM, ILO, IMM, and RSA Able to discover and Work with virtualized environments including Microsoft Virtual Server, VMware, and Xen. Capable of viewing topology that shows the connections between physical and virtual resources Create automation plans based on events from virtual and physical resources and automation actions such as relocating a virtual server based on critical hardware alerts Create, delete and manage virtual servers and virtual farms for several virtualization technologies Relocate virtual servers to alternate physical hosts Ability to discover network devices and review network device inventory. Able to Monitor the health and status of network devices. View network device configuration settings, and apply templates to configure devices Management software should have upward integration with HP OpenView, Microsoft System Center Operations Manager, CA Unicenter, Tivoli Enterprise Server should support latest version of Microsoft windows, Redhat, Novell and Vmware Server High End Specification Server should be quoted with Dual Hexa Core Processor Intel Xeon E5-2620 Processor 1333 Mhz L3 Cache 15 MB No of processors Should be configured with 2 processors Chipset Intel Chipset/ OEM Chipset / Or Equivalent Server should be configured with 32 GB memory ( 4 * 8GB ) PC3-12800 Memory 1600MHz LP Registered ECC DIMMs DIMM Slots Server should support 24 DIMM Slots Memory DDR3 Registered Memory with ECC, Chipkill, Spare Memory, and Memory Property Mirroring features Hard Disk 3* 300GB 10K SAS 6Gbps 2.5in Slim-HS HDD. Server should support up to Drives 16 2.5" SAS/SATA hard disk Integrated 6Gbps SAS hardware RAID 0, 1 and 10. Raid controller should RAID support on line Raid level migration, on line capacity expansion and data Controller scrubbing as well. Optical Drive DVD-RW Graphics Controller 16MB DDR2-SDRAM
Gigabit Ethernet Ports PCI Slots Redundant Supply Redundant Cooling Fans Form Factor Four integrated Gigabit Ethernet ports with full duplex / TCP/IP Offload Engine (TOE). 4 PCIe slots Server to be configured with Redundant Supplies Hot-swap and redundant cooling Fans to be configured in the system 2U or more Form Factor Ports Failure Alerting Mechanism Ease of failure identification 2U or more Server should support 6 Number of external USB 2.0 ports as well as 2 number of Internal USB ports for installation of Hypervisor key, also should support 2 Number of Video ports and Ethernet Management port The server should be able to alert impending failures on server component (processors, VRMs, memory, HDDs, fans, and power supplies) to administrator in order to avoid any downtime on the server due to actual failure Server should send an alert notification on the system front panel for failure detected on the system and also provide a mechanism to easily identify the failed component during servicing which will help in reducing the downtime on the server and maximizing the availability for business-critical applications Mnaagement Functionality Warranty Should support integrated management functionality and should support round-the-clock remote access and management of server, Remote management independent of the status of the server, Remote control of hardware and operating systems, also support IPMI 2.0 Interface, Thermal Monitoring, Fan Control, IPMI Platform Event Trap Alerting, IPMI Serial over LAN functionality, SNMPv1 and SNMPv3 Interfaces, SNMP TRAP, E- mail, and CIM Indication Alerting, Failure Screen Capture for Operating System hangs, Remote Media. Server should have dedicated remote Management port on the rear of the chassis. 3 Years Onsite Comprehensive Warranty Server Mid end Specification Form factor/height 1U Rack Processors Memory (max) DIMM Slots Intel Xeon 4C E5 2609 (Quad Core) 2.40Ghz 10 Mb 1066 Mhz also support for add on processor 8GB (1x8GB, 2Rx4, 1.5V) PC3-10600 CL9 ECC DDR3 1333MHz LP RDIMM should supports maximum Up to 768 GB 24 slots (UDIMM/RDIMM/LRDIMM)
Hard Disk Disk bays RAID support supply Hot-swap components Network interface Expansion slots USB ports VGA ports Maximum internal storage Energyefficiency compliance Systems management Operating systems supported Limited warranty 3x300GB 10K 6Gbps SAS 2.5" SFF G2HS HDD Eight 2.5" or three 3.5" hard disk drives (HDDs) Integrated 6 Gbps hardware RAID-0, -1, -10; optional RAID-5, -50 or -6, - 60 Redundant 550 W ac, 750 W ac, or 750 W dc supplies, fan modules and hard disk drives 4 1 Gb ethernet 2 PCIe 3.0 slots, optional 1 PCI-X 2 (three for 3.5" model) front/4 back/1 internal 1 front/1 back Up to 8 TB (2.5" model) or 9 TB (3.5" model) SAS/SATA Compliant with 80 PLUS Platinum and ENERGY STAR (model dependent) IBM IMM2 with optional FoD remote presence, Predictive Failure Analysis, Diagnostic LEDs, light path diagnostics panel, Automatic Server Restart, IBM Systems Director and Active Energy Manager Microsoft Windows Server 2008 R2, Red Hat Enterprise Linux, SUSE Linux Enterprise Server, VMware vsphere 3-year customer replaceable unit and onsite service, next business day 9 5, service upgrades available Server Low End Specification Form factor/height Rack/2U Should be configured with One Intel Xeon E5620 (Quad Core) Processor 2.40 Ghz 12Mb 1066 Mhz Number of processors(std/max) 1/2 Cache 12 MB L3 Memory Hard disk Expansion slots Maximum HDD support Disk bays (total/hot swap) Maximum internal storage Network interface Configured with 8GB (1x8GB, 2Rx4, 1.5V) PC3-10600 CL9 ECC DDR3 1333MHz LP RDIMM and supports maximum Up to 192 GB in 12 slots, using RDIMMs 3x500GB 7200 RPM 3.0 GB/sec Hot-Swap SATA Two x8 PCIe Gen II slots and one x4 PCIe Gen II buried slot 8 hard disk bays Up to four 3.5" simple-swap SATA HDDs or up to eight 3.5" hot-swap SAS/SATA HDDs Up to 16.0 TB hot-swap SAS or SATA Integrated two ports Gigabit
supply 2nos ; 460 W or 675 W HE each Hot-swap components supplies, HDDs RAID support Configurable with Raid 5 Systems management Operating systems supported Warranty IBM IMM with Virtual Media Key, PredictiveFailure Analysis, Integrated Service Processor,light path diagnostics panel, Automatic ServerRestart, IBM Systems Director and ActiveEnergy Manager, IBM ServerGuide Microsoft Windows Server, Red HatLinux, SUSE Linux, VMware 3-Year customer replaceable unit and on-sitelimited warranty Workstation Specification Processor Intel Xeon E3-1220 3.10 GHz v2 RAM 4GB (1 X 4GB) Non-ECC configurable Up to 32 GB 1600 MHz DDR3 HDD/ 1TB SATA 3.5 SATA, configurable Up to 3 HDDs ODD DVDRW Graphics NVIDIA Quadro 2000 1Gb graphics with Dual Display Port, Dual-link DVI and supporting maximum resolution of 2560x1600 Monitor 22 LED Monitor Multiple input options DisplayPort, DVI-D and V,Wide viewing angle with native resolution of 1680 x 1050; 16:10 Aspect ratio; 5ms response time,energy STAR 5.1 compliant, TCO certified Edge 1.1, and Mercury/Arsenic free glass Ports (4) USB 3.0 (Rear);(2) USB 2.0 (Front) Ethernet Gigabit ethernet OS Windows 7 Professional 64-bit Warranty 3 Years on-site