s RT series Miniature Printed Circuit oard Relays, Sockets and ccessories
pplied Coil Voltage (% of rated nom.) RT series (DC Coil) 6 mp PC oard Miniature Relay Meets VDE 0mm Spacing, KV Dielectric File E7 File LR734 NR 606 Features SPST through DPDT contact arrangements. Immersion cleanable and flux tight versions available. VDE 0mm spacing, kv dielectric, coil to contacts. UL Class F coil insulation system. Conforms to UL 08, 873, 33 and 90. Low profile;.7mm height. Sensitive coil; 400mW. Withstand surge voltage of 0,000V. Contact Data rrangements: Form (SPST-NO) Wiring Diagram Code, 3. Form (DPST-NO) Wiring Diagram Code. Form C (SPDT) Wiring Diagram Code, 3. Form C (DPDT) Wiring Diagram Code. Material: Silver-nickel 90/0. Minimum Load: V/00m. Expected Mechanical Life: 0 million operations. Initial Contact Resistance: 00 milliohms max @ VDC. Designed to meet UL/CS/VDE ratings with relay properly vented. Remove vent nib after soldering and cleaning. UL/CS/VDE Ratings @ C 0/0 @ 77VC Resistive/GP 00K 0/0 @ 30VDC Resistive 00K / @ 0VC Resistive/GP 30K / @ 30VDC Resistive 30K 3/4 HP @ 480VC* Motor 6K / HP @ 40VC* Motor 6K /3 HP @ 0VC* Motor 6K 48 LR/0 FL @ 40VC* Motor 30K TV-3 @ 0VC* Tungsten K 300, 70V @ 40VC* Pilot Duty 30K 3 6/6 @ 0VC Resistive/GP 0K 0/0 @ 77VC Resistive/GP 30K 0/0 @ 4VDC Resistive 30K 6/6 @ 30VDC Resistive 30K HP @ 480VC* Motor 6K HP @ 40VC* Motor 6K / HP @ 0VC* Motor 6K 60 LR/0 FL @ 0VC* Motor 30K TV- @ 0VC* Tungsten K 300, 70V @ 40VC* Pilot Duty 30K 300, 360V @ 40VC** Pilot Duty 30K 8/8 @ 77VC Resistive/GP 00K 8/8 @ 30VDC Resistive 00K 0/0 @ 0VC Resistive/GP 30K 0/0 @ 30VDC Resistive 30K / HP @ 40VC* Motor 6K /4 HP @ 0VC* Motor 6K 34.8 LR/6 FL @ 0VC* Motor 30K 7.4 LR/ FL @ 40VC* Motor 30K 300, 360V @ 40VC* Pilot Duty 30K TV-3 @0VC* Tungsten K * Form only ** Form only Coil Data @ C Voltage: to 48VDC. Nominal Power @ C: 400mW. Duty Cycle: Continuous. Initial Insulation Resistance: 0,000 megohms, min., at C, 00VDC and 0% rel. humidity. Coil Data @ C DC Must Nominal Nominal Resistance Operate Coil Voltage in Ohms Voltage Current VC ±0% VC (m) 0/60Hz. 00 6 3. 80 006 90 4. 66.7 009 0 6.3 44.4 0 360 8.4 33.3 08 80.6. 04,440 6.8 6.7 048,760 33.6 8.3 Max. mbient Temp. vs. Coil Voltage 300 60 0 80 40 00 60 0 0 40 60 80 00 Operate Data @ C Must Operate Voltage(DC): 70% of nominal. Must Release Voltage(DC): 0% of nominal. Operate Time (Excluding ounce): 7 ms, typ., ms max. at nom. voltage. Release Time (Excluding ounce): 3 ms, typ., 6ms max. at nom. voltage. Environmental Data Max. llowable mbient Temp. ( C) : Coil temperature = mbient temperature. : 0% of nominal coil voltage at rated contact load. 0 8 6 Temperature Range: Storage: -40 C to +0 C. Operating: -40 C to +8 C at rated current. Vibration, Operational N.O.:0.06 (.6mm) max. excursions from 0 - Hz: N.C.:0.03 (0.8mm) max. excursions from 0 - Hz: with no contact opening >0µs Initial Dielectric Strength etween Open Contacts: >,000VC ( minute). etween Poles (code ): >,00VC ( minute). etween Coil and Contacts: >,000VC ( minute). Surge Voltage (DC): >0,000VC x (. x 0 µsec). Mechanical Data Termination: Printed circuit terminals. Enclosures: RT, 3, 4: Flux-tight, top vented, plastic case. RT, D, E: Immersion cleanable, plastic case. Weight: 0.3 oz. (0g) approximately.
Ordering Information Typical Part Number RT 3 4 0. asic Series: RT = Miniature, printed circuit board relay.. Enclosure: = pole, Pinning 3.mm, flux-tight (Code ). = pole, Pinning 3.mm, sealed (Code ). 3 = pole 6, Pinning mm, flux-tight (Code 3). D = pole 6, Pinning mm, sealed (Code 3). 4 = pole 8, Pinning mm, flux-tight (Code ). E = pole 8, Pinning mm, sealed (Code ). 3. Contact rrangement: = Form C (SPST) (Requires wiring diagram codes or 3.) = Form C (DPST) (Requires wiring diagram code.) 3 = Form (SPST-NO) (Requires wiring diagram codes or 3.) 4 = Form (DPST-NO) (Requires wiring diagram code.) 4. Contact Material: 4 = Silver-nickel 90/0 (standard stock). = Silver cadmium Oxide (Special order). Coil Voltage: 00 = VDC 009 = 9VDC 08 = 8VDC 048 = 48VDC 006 = 6VDC 0 = VDC 04 = 4VDC Stock Items RT40 RT404 RT340 RT3404 RT400 RT40 RT404 RT340 RT3404 RT340 RT3404 RT3340 RTD400 RTD40 RTD404 RTD340 RTD3404 RT440 RT4404 RT4440 RT44404 RTE400 RTE40 RTE404 RTE440 RTE4404 Outline Dimensions reaking Capacity.6 (.7).7 (4.3).4 (9).0 (.7) 6X.03 X.00 (.80 X.) X.00 X.00 (. X.) Pole Pole 0 0 0 0 0 00 00 300 0 0 0 00 00 300 0 0 PC oard Layouts (ottom View) Pole 3.mm.0 DI..76 (7.0).0 DI..300 (7.6).800 (0.3) Pole 6 Pole 8 mm.0 DI..400 (6).0 DI..300 (7.6).800 (0.3) : 6 Version. : Version. : Contact. : Contacts in series. Contact Life for Resistive C Load (Typical) Operations 0 7 0 6 0 : 8 Model : Model C: 6 Model C Code Code 3 & Note: On single throw models, only necessary terminals are present. Wiring Diagrams (ottom View) Pole Pole 6 Pole 8 0 4 0 0.4 0.8..6.0.4.8 3. 3.6 4.0 reaking Capacity (kv) Note: Data from 0VC @ 70 C. Code Code 3 Code Note: On single throw models, only necessary terminals are present.
pplied Coil Voltage (% of rated nom.) RT series (C Coil) 6 mp Miniature Printed Circuit oard Relay Meets VDE 0mm Spacing, KV Dielectric File E3889 File LR438 NR 606 Features SPST through DPDT contact arrangements. Immersion cleanable and flux tight versions available. Meets VDE 0mm spacing, kv dielectric, coil to contacts. Conforms to UL 08, 873 and 33. Contact Data rrangements: Form (SPST-NO) Wiring Diagram Code, 3. Form (DPST-NO) Wiring Diagram Code. Form C (SPDT) Wiring Diagram Code, 3. Form C (DPDT) Wiring Diagram Code. Material: Silver-nickel 90/0. Minimum Load: V/00m. Expected Mechanical Life: 0 million operations. Designed to meet UL/CS/VDE ratings with relay properly vented. Remove vent nib after soldering and cleaning. UL/CS Ratings @ C: NO @ 40VC GP 30K 0/ @ 40VC Resistive/GP 00K 8 @ 8VDC Resistive 30K HP @ 40VC* Motor 6K / HP @ 0VC* Motor 6K 8 @ 8VDC* Resistive 30K 300 Pilot Duty 6K 3 6/8 @ 40VC GP 6K 8 @ 8VDC Resistive 30K / HP @ 0VC* Motor 6K HP @ 40VC* Motor 6K 48 LR, 8 FL @ 40VC Motor 30K 300 Pilot Duty 6K 8 @ 40VC Resistive 30K 8 @ 8VDC Resistive/GP 30K / HP @ 40VC Motor 6K /4 HP @ 0VC Motor 6K 300 Pilot Duty 6K * Form only VDE Ratings @ C: @ 0VC Resistive 30K @ 0VC Resistive 00K 3 6 @ 0VC Resistive 0K 6 @ 0VC Resistive 0K 8 @ 0VC Resistive 30K 8 @ 0VC Resistive 0K Coil Data @ 0 C Voltage: 4,, 30VC. Nominal Power @ C:.7V. Duty Cycle: Continuous. Initial Insulation Resistance: 0,000 megohms, min., at 0 C, 00VDC and 0% rel. humidity.. Coil Data DC Must Nominal Nominal Nominal Resistance Operate Drop-out Coil Coil Voltage in Ohms Voltage Voltage Current Current VC ±0% VC VC (m) 0Hz. (m) 60Hz. 4 30 8.0 3.6 3.6 4.3 8,00 86.3 7.3 6.6. 30 3,00 7. 34. 3.3.3 Max. mbient Temp. vs. Coil Voltage 300 60 0 80 40 00 0 8 6 60 0 0 40 60 80 00 Operate Data Max. llowable mbient Temp. ( C) : Coil temperature = mbient temperature. : 0% of nominal coil voltage at rated contact load. Must Operate Voltage: See coil data. Operate Time (Excluding ounce): 8 ms, typ., at nom. voltage. Release Time (Excluding ounce): ms, typ., at nom. voltage. Environmental Data Temperature Range: Storage: -40 C to +0 C. Operating: -40 C to +70 C at rated current. Vibration: 30-0 Hz: at 0g with no contact opening >0µs on the N.O. contact; at g with no contact opening >0µs on the N.C. contact. Initial Dielectric Strength etween Open Contacts: >,000VC ( minute). etween Poles (code ): >,00VC ( minute). etween Coil and Contacts: >,000VC ( minute). Creepage/Clearance, Coil to Contact: 0/0mm. Mechanical Data Termination: Printed circuit terminals. Enclosures: RT, 3, 4: Flux-tight, top vented, plastic case. RT, D, E: Immersion cleanable, plastic case. Weight: 0.4 oz. (g) approximately.
Ordering Information Typical Part Number RT D 4 4. asic Series: RT = Miniature, printed circuit board relay.. Enclosure: = pole, Pinning 3.mm, flux-tight (Code ). = pole, Pinning 3.mm, sealed (Code ). 3 = pole 6, Pinning mm, flux-tight (Code 3). D = pole 6, Pinning mm, sealed (Code 3). 4 = pole 8, Pinning mm, flux-tight (Code ). E = pole 8, Pinning mm, sealed (Code ). 3. Contact rrangement: = Form C (SPST) (Requires wiring diagram codes or 3.) = Form C (DPST) (Requires wiring diagram code.) 3 = Form (SPST-NO) (Requires wiring diagram codes or 3.) 4 = Form (DPST-NO) (Requires wiring diagram code.) 4. Contact Material: 4 = Silver-nickel 90/0.. Coil Voltage: 4 = 4VC 730 = 30VC 6 = VC Stock Items RT44 RT46 RT4730 RTD44 RTD46 RTD4730 RTE44 RTE46 RTE4730 Outline Dimensions reaking Capacity.6 (.7).0 (.7) Pole Pole.7 (4.3).4 (9) 6X.03 X.00 (.80 X.) X.00 X.00 (. X.) 0 0 0 0 0 00 00 300 0 0 0 00 00 300 0 0 PC oard Layouts (ottom View) Pole 3.mm.0 DI..76 (7.0).0 DI..96 (7.0).788 (0.0).0 DI. Wiring Diagrams (ottom View) Pole 6 Pole 8 mm.0 DI..394 (0.0).96 (7.0) Code Code 3 & Note: On single throw models, only necessary terminals are present..788 (0.0) : 6 Version. : Version. Contact Life for Resistive C Load (Typical) Operations 0 7 0 6 0 0 4 0 0.4 0.8..6.0.4.8 3. 3.6 4.0 reaking Capacity (kv) Note: Data from 0VC @ 70 C. : 8 Model : Model C: 6 Model C : Contact. : Contacts in series. Pole Pole 6 Pole 8 Code Code 3 Code Note: On single throw models, only necessary terminals are present.
RT series (Latching) 6 mp Miniature Printed Circuit oard Relay Meets VDE 0mm Spacing, KV Dielectric File E3889 File LR438 NR 606 Features Latching relay with or coils. SPDT (6) and DPDT (8) contact arrangements. Flux tight enclosure. Meets VDE 0mm spacing, kv dielectric, coil to contacts. Conforms to UL 08, 873 and 33. Contact Data rrangements: Form C (SPDT) Wiring Diagram Code 3. Form C (DPDT) Wiring Diagram Code. Material: Silver-nickel 90/0. Minimum Load: V/00m. Expected Mechanical Life: million operations, pole. million operations, pole. Coil Data @ 0 C Voltage: to 4VDC*, coil. 3 to 4VDC*, coil. Nominal Power @ C: 400mW, coil. 600mW, coil. Duty Cycle: Continuous. Initial Insulation Resistance: 0,000 megohms, min., at 0 C, 00VDC and 0% rel. humidity. * Other coil voltages upon request. Coil Data DC Nominal Nominal Resistance Set Reset Coil Voltage in Ohms Voltage Voltage Current VDC ±0% VDC VDC (m) 0 6 3. 6.0.7 6.0 80.0 06 90 4. 7. 3.30 7. 66.7 360 8.4 4.4 6.60 4.4 33.3 4,440 6.8 8.8 3.0 8.8 6.7 Designed to meet UL/CS/VDE ratings with relay properly vented. Remove vent nib after soldering and cleaning. UL/CS ratings @ 70 C: 3 6/8 @ 40VC GP 6K 8 @ 8VDC Resistive 30K / HP @ 0VC* Motor 6K HP @ 40VC* Motor 6K 48 LR, 8 FL @ 40VC Motor 30K 300 Pilot Duty 6K 8 @ 40VC Resistive 30K 8 @ 8VDC Resistive/GP 30K / HP @ 40VC Motor 6K /4 HP @ 0VC Motor 6K 300 Pilot Duty 6K * Form only VDE Ratings @ 70 C: 3 6@ 0VC Resistive 0K 8 @ 0VC Resistive 30K 8 @ 0VC Resistive 30K 8 @ 0VC Resistive 00K Coil Data DC Nominal Nominal Resistance Set Reset Coil Voltage in Ohms Voltage Voltage Current VDC ±0% VDC VDC (m) 0 4 3. 7..7 4. 0.0 06 4. 9.0 3.30 9.0 08.0 40 8.4 8.0 6.60 8.0 0.0 4 886 6.8 36.0 3.0 36.0 7.0 Operate Data @ 0 C Must Operate Voltage: See coil data. Operate Time (Excluding ounce): ms, typ., at nom. voltage. Release Time (Excluding ounce): 4 ms, typ., at nom. voltage. Max. Switching Rate: 360 ops. at rated load. Environmental Data Temperature Range: Storage: -40 C to +0 C. Operating: -40 C to +70 C at rated current. Vibration: 30-00 Hz: N/C opens at >3g and changes from reset to set at >g; Shock: N/C opens at >6g and changes from reset to set at >g.; Initial Dielectric Strength etween Open Contacts: >,000VC ( minute). etween Poles (code ): >,00VC ( minute). etween Coil and Contacts: >,000VC ( minute). Creepage/Clearance, Coil to Contact: 0/0mm. Mechanical Data Termination: Printed circuit terminals. Enclosures: RT 3, 4: Flux-tight, top vented, plastic case. Weight: 0.46 oz. (3g) approximately.
Ordering Information. asic Series: RT = Miniature, printed circuit board relay.. Enclosure: 3 = pole 6, Pinning mm, flux-tight (Code 3). 4 = pole 8, Pinning mm, flux-tight (Code ). 3. Contact rrangement: = Form C (SPDT) (Requires wiring diagram code 3.) = Form C (DPDT) (Requires wiring diagram code.) 4. Contact Material: 4 = Silver-nickel 90/0.. Coil Voltage: Coil Coil Voltage 0 F0 = VDC 06 F06 = 6VDC F = VDC 4 F4 = 4VDC Typical Part Number RT 3 4 0 Stock Items Consult factory for availability. Outline Dimensions Wiring Diagrams (ottom View).6 (.7).0 (.7) Pole 6 Pole 8 6X.03 X.00 (.80 X.) 4 4.4 (9) 4 4.7 (4.3) * X.00 X.00 (. X.) * Coil version only 3* * Coil Version Only Code 3 Code 3* PC oard Layout (ottom View) Pole 6 Pole 8 mm reaking Capacity Pole Pole.394 (0.0).0 DI..788 (0.0) 0 0 0 0.0 DI. *.96 (7.).48* (3.76 * Coil Version Only 0 0 0 00 00 300 0 0 0 00 00 300 : 6 Version. : Version. : Contact. : Contacts in series. Code 3 &
RT series Sockets and ccessories File E349 File LR438 NR 38 RT786 with RPMU0730 RP7860 RT606 Sockets for RT Series Relays RT7864 0, 300VC mm Pinning RT786, Pole 0, 0VC Pole x 0, 0VC mm Pinning RT7866, Pole, 300VC Pole x, 300VC mm Pinning 4 4 4 4 4.97 (7.).97 (7.).97 (7.) Relay Ejector.60 (.).77 (4.).874 (.).693 (43) Hold-Down Spring RT606.60 (.).77 (4.).874 (.).693 (43) Hold-Down Spring RT606.60 (.).77 (4.).874 (.).83 (8) Ejector/Hold-Down Spring RT606 3 Module RP7860 0, 0VC 3.mm Pinning PC oard Layout (ottom View) RP7860 Pole 0, 0VC Pole x 0, 0VC mm Pinning PC oard Layout (ottom View).38 (3.).0 (.08). (3.0). (3.0). (.7).89 (4.8).89 (4.8).34 (9.0).4 (0.8).60 (.4).30 (7.6).80 (0.3) Ø.06 DI. (.). (.7).89 (4.8).89 (4.8).34 (9.0).4 (0.8).0 (.08).30 (7.6).60 (.4) Ø.06 DI. (.) Hold-Down Spring RP604 Hold-Down Spring RP604 Socket and ccessory Selection Table Stock items are boldfaced. Socket Socket Termination Hold-Down Spring RT7864, DIN Screw Terminal RT606 RT786, DIN Screw Terminal RT606 RT7866 DIN Screw Terminal RT606 RP7860 PC RP604 RP7860 PC RP604 RPMU0730 RC Network 0..30VC * Note. Not suitable for bistable relay with two coils.. For a 6 pole relay the following jumpers have to be connected; to, to and 4 to 4. 3. Insertion of the relay. First the ejector (and eventually the module) has to be mounted onto the socket. Then the relay has to be set in the correct position and pressed into the socket until the ejector snaps over the top of the relay. Siemens Electromechanical Components, Inc. 700 Westpark Drive Peachtree City, G 3069-498 Specifications and availability subject to change without notice. 3C7800 Printed in U.S.. IH/-99