INTIMATE User Manual INDEX Description-About GSM 2 Requirements 2 Select a SIM card 2 Installation.3 Programming the GSM Auto-Dialer.3 Programming Commands-Quick Reference..6
Thank you for purchasing our product. Please read this manual before starting to install the GSM-Auto dialer. If you are unsure how to connect to the device you wish to control refer to a qualified person IMPORTANT Please read through this instruction manual before you start to install and program the GSM-Auto Dilaler.. If you are unsure how to connect the device you wish to control refer to a qualified person. About GSM Auto-Dialer This is a device which built-in with GSM module can enable your existing hardwired alarm system using GSM cellular network, rather than telephone line network for alarm network transmission. It doesn t have any input or outputs, and can not pre-set phone numbers for auto-dialing, also it is without SMS alert function. Requirements The INTIMATE GSM Auto-Dialer requires a 12 volt DC power supply capable of providing a minimum current 2000mA, typical current consumption is 500mA. An active mobile phone SIM card with sufficient credit to send confirmation text message when programming the Auto-Dialer. Select a SIM card All new SIM cards have to be registered with the network provider before they can be used, usually by calling the network provider or registering on their website please refer to the instructions supplied with your SIM card. During the registration procedure a confirmation code or text message is usually sent to the
SIM cards telephone number, to be able to read and react to the message you will need to insert the SIM card into an unlocked mobile phone. After successfully registering the SIM card, ensure there is sufficient credit on the card for programming confirmation texts to be sent from the Auto-Dialer unit. You MUST ensure that the PIN request is disabled from the SIM card before inserting it into the GSM Auto-Dialer. If you do not disable the PIN request the GSM Auto-Dialer will not work. If the PIN request is not disabled and the unit is switched on more than 3 times you will have to reset the PIN using the PUK code which will have to be obtained from the service provider. To check the PIN request status of your SIM card, place the card in an unlocked mobile phone, switch the phone on. If you are able to make calls without entering a PIN number the PIN request is disabled. If a PIN number is requested refer to the instructions supplied with the SIM card and then look through the phones options for the disable PIN request and disable it. The SIM card is now ready to use. We recommend that if you are using a pay as you go (PAYG) SIM card that you choose to automatically Top-Up when the cards credit falls below a certain limit please contact your network provider or visit their website for more details. Most but not all PAYG SIM cards will be de-activated by the network if not used to make an outgoing voice call or send an SMS text message within a specific period. To prevent this simply send the GSM-Auto-Dialer a txt command, it will reply by text message, do this once a month to keep the SIM card active. Installation Insert the SIM card, to access the SIM card carrier fix it properly to it. Connect a 12 volt DC power supply to AC terminals and switch ON the power, the red power LED will light indicating power is present, the green network LED indicator will ON after 20 seconds and it indicate GSM is ready to operate. Programming the GSM Auto-Dialer The GSM-Auto is programmed by sending it SMS text commands, these are sent to the telephone number of the SIM card installed in the GSM-AUTO. The password command must pre-fix all SMS text commands it is recommended the default password be changed.
Remember that all SMS text commands must always be sent using CAPITAL LETTERS DO NOT add spaces or any other characters Commands #PWD Password This command must always pre-fix any SMS text commands sent to the unit. #PWDXXXXXX where XXXXXX is the six digit password. The units default password is 123456 so initially #PWD123456 is entered before the command, of course when you change the password you will prefix all commands with the new password Default password : 123456 #CCP Changing the Current Password To change the password of the unit youuse the #CCP Command and to change the password from the default 123456 to 123123 you would send the following SMS text message to the unit. #PWD123456#CCP123123#CCP123123# IMPORTANT Please make a note of your new password, if you lose or forget the password you will not be able to access the unit. We have now changed the password to123123 and will use this in the following examples #TEL Administrator List This is the command that allows you to add or remove the administrator telephone numbers. Up to 8 Administrator numbers can be in the list and the numbers can contain up to 16 digits. If an administrator wishes to receive text messages whilst abroad prefix the number with the country code for example if a INDIA number +91XXXXXX.
To add to the administrator +91XXXXXX list you would send the following SMS text message to the unit. Examples:- 1 #PWD123123#TEL1=+91XXXXXX# 2 #PWD123123#TEL1=+91XXXXXX#TEL2=+91XXXXXX#TEL3=+91XXXXXX# DEL Delete Tele-Numbers This is the command that allows you to delete the administrator telephone numbers from stored memory locations. Examples:- 1 #PWD123123#DEL1# 2 #PWD123123#DEL134# (where 1,2,3 is TEL1,TEL2,TEL3 respectively) 3 #PWD123123#DEL1234# 4 #PWD123123#DEL# (Delete all tele-numbers) ERROR METHOD:- #PWD123123#DEL1324# (please change 1324 to 1234)
Programming Commands-Quick Reference FUNCTION COMMAND FORMAT NOTE Changing the #CCP #PWD123456#CCP123123 password #CCP123123# Administrator list #TEL #PWD123456#TEL1=+91XXXXXX# TEL2=+91XXXXXX#TEL3=+91XXXXXX# Default 123456 Up to 8 Telenum bers & 16 digits #TEL3 #PWD123456#TEL3=+91XXXXXX# Add a number to admin list Delete numbers #DEL #PWD123456#DEL# Delete all numbers #DEL1 #PWD123456#DEL1# Delete a number #DEL134# #PWD123456#DEL134# Random method deletion End.