Chuck / Mid centering device / Adaptors Sets Chuck A 010 818 000 Conical chuck Hofmann 1.290,00 A 010 908 000 Chuck Corghi/Faip/Sice 1.290,00 Mid centering device and Basic centering device A 100e818 026 Basic centering device conical Tr40x3 covered spring, 200 mm usable length (Beissbarth / Sicam) 3.050,00 A 100e818 028 Basic centering device conical Tr40x4 covered spring, 240 mm usable length 3.050,00 A 100e818 040 Basic centering device conical Tr40x3 covered spring, 240 mm usable length 3.050,00 A 100e999 057 Closed basic centering device Schenck, Tr 40x3 188 mm usable length, covered spring, red mark 3.050,00 A 104 818 038 Mid centering device Tr40x3, 3 cones, ProGrip, 200 mm usable length 4.935,00 A 104 818 132 Mid centering device Tr40x3, 3 cones, ProGrip, 240 mm usable length 5.160,00 A 104 968 130 A 105 818 001 Mid centering device Tr 40x3, 3 cones, ProGrip, 181 mm usable length, FMC, Cemb (old) Spring-less Mid centering device Basic centering conical DuoMatic Tr40x3, ProGrip, clamping hood ProGrip Kit and Adaptor Sets 5.160,00 10.400,00 A 124 283 000 ProGrip kit Tr 28,55x3 Includes 143 283 003 / 190 008 002 1.150,00 A 124 283 001 ProGrip kit Tr 28.55x3 Includes 143 283 006 / 190 008 002 975,00 A 124 288 000 ProGrip kit Tr 28,55x8,46 Includes 143 288 003 / 190 008 002 975,00 Side 1
A 124 303 000 ProGrip kit Tr 30x3 Includes 143 303 003 / 190 008 002 1.150,00 A 124 363 000 ProGrip kit Tr 36x3 Includes 143 363 003 / 190 008 002 1.150,00 A 124 363 001 ProGrip kit Tr 36x3 with turning handles Includes 143 363 006 / 190 008 002 1.150,00 A 124 383 000 ProGrip kit Tr 38x3 Includes 143 383 003 / 190 008 002 1.150,00 A 124 383 001 ProGrip kit Tr 38x3 with turning handles Includes 143 383 006 / 190 008 002 1.150,00 A 124 403 000 ProGrip kit Tr40x3 Includes ProGrip 143 403 003 and 190 008 002 1.150,00 A 124 404 000 ProGrip kit Tr40x4 Includes ProGrip 143 404 003 and 190 008 002 1.150,00 A 124 404 001 ProGrip kit Tr40x4 with turning handles 1.150,00 A 124 405 000 ProGrip kit Tr40x4 Includes 143 405 003 / 190 008 002 1.150,00 A 124 408 005 ProGrip Kit Tr 40x8,46 Includes 140 408 033 / 190 008 002 1.950,00 A 124 588 000 Adaptor set Cemb/TipTop/Hofmann, shaft, pressure piece, pr. ring Ø 36 mm 3.375,00 A 124 588 031 Adaptor set Cemb / Rav / Teco Tr36x3 Shaft, 3 cones, ProGrip etc. 2.750,00 A 124 588 033 Adaptor set Cemb / Rav / Teco, 3 cones, ProGrip Ø36 mm 1.770,00 A 124 589 000 Adaptor set Cemb/TipTop/Hofmann, shaft, pressure piece, pr. ring Ø 40 mm 3.375,00 A 124 589 030 Adaptor set Cemb & TipTop Tr40x4 Shaft, 3 cones, ProGrip Kit 2.750,00 Side 2
A 124 589 031 Adaptor set Cemb & TipTop 40 mm, 3 cones, ProGrip Ø40 mm 1.770,00 A 124 627 036 Adaptor set Fasep 3 cones, ProGrip Kit,Shaft 2.505,00 A 124 657 033 Adaptor set Mondolfo BM 1000-8000 Tr28,55x3 Shaft, 3 cones, ProGrip Kit 2.750,00 A 124 658 031 Adapter set HAWEKA BM1000-8000 Tr40x3 Shaft 3 Cones, ProGrip Kit 2.750,00 A 124 907 032 Adaptor set Corghi / Sice / Faip Tr38x3. Shaft 3 Cones, ProGrip Kit 2.750,00 A 124 907 230 Adapter-Set, Mondolfo, Tr40x3 Shaft, ProGrip Kit, 3 Cones, clamping hood, Corghi, HPA, Teco 2.950,00 A 124 957 033 Adaptor set Balco/Haweka Tr40x3 shaft, ProGrip Kit, 3 cones 2.750,00 A 124 957 530 Adaptor set Balco/Snap-On/Sun 28,55x3 mm shaft ProGrip Kit, turning handles 3 cones 2.750,00 A 124 958 037 Adaptor set Balco/JBC serie 9000, 40x3 Shaft, ProGrip Kit, 3 cones Quick nuts ProGrips / Accessories Quick nuts ProGrip (Version: steel) 2.750,00 A 140 403 033 ProGrip Tr 40 x 3 mm 1.925,00 A 140 404 033 ProGrip Tr 40 x 4 mm 1.925,00 A 140 408 033 ProGrip Tr 40 x 8.46 mm 1.925,00 A 140 466 003 ProGrip Tr 46 x 6 mm 2.750,00 Side 3
ProGrip quick nuts A 143 283 003 ProGrip Tr 28,55 x 3 mm 960,00 A 143 283 006 ProGrip Tr 28,55 x 3 mm, with turning Handles 960,00 A 143 285 003 ProGrip Tr 28,55 x 3,5 mm 960,00 A 143 285 006 ProGrip Tr 28,55 x 3,5 mm, with turning handles 960,00 A 143 288 003 ProGrip Tr 28,55 x 8,46 mm 960,00 A 143 363 003 ProGrip Tr 36 x 3 mm 960,00 A 143 363 006 ProGrip Tr 36 x 3 mm, with turning handles 960,00 A 143 383 003 ProGrip Tr 38 x 3 mm 960,00 A 143 383 006 ProGrip Tr 38 x 3 mm, with turning handles 960,00 A 143 403 003 ProGrip Tr 40 x 3 mm 960,00 A 143 403 006 ProGrip Tr 40 x 3 mm, with turning handles 960,00 A 143 404 003 ProGrip Tr 40 x 4 mm 960,00 A 143 404 006 ProGrip Tr 40 x 4 mm, with turning handles 960,00 A 143 405 003 ProGrip Tr 40 x 4 mm original Hofmann 960,00 A 143 405 006 ProGrip Tr 40 x 4 mm with turning handles, original Hofmann 960,00 Side 4
A 143 408 003 ProGrip Tr 40 x 8,46 mm 960,00 Spare Parts for Series ProGrip B 140e363 310 Repair kit 36 x 3 mm (Version: steel) 746,00 B 140e383 310 Repair kit Tr 38 x 3 mm (Version: steel) 746,00 B 140e403 310 Repair kit Tr 40 x 3 mm (Version: steel) 746,00 B 140e404 310 Repair kit Tr 40 x 4 mm (Version: steel) 746,00 B 141e283 310 Repair kit Tr 28,55 x 3 mm ProGrip 746,00 B 141e285 310 Repair kit Tr 28,55 x 3.5 ProGrip original Balco 746,00 B 141e363 310 Repair kit Tr 36 x 3 mm ProGrip 746,00 B 141e383 310 Repair kit Tr 38 x 3 mm ProGrip 746,00 B 141e403 310 Repair kit Tr 40 x 3 mm ProGrip 746,00 B 141e404 310 Repair kit Tr 40 x 4 mm ProGrip 746,00 B 141e408 310 Repair kit Tr 40x8,46 mm ProGrip 899,00 Cones / Centering Rings / Conical Rings Pressure Pieces Enter diameter of the balancer shaft as 4th and 5th number (28, 36, 38, 40) A 150 xx0 008 Centering cone 42-64,5 mm 386,00 A 150 xx0 009 Centering cone 54-79,5 mm 346,00 Side 5
A 150 xx0 010 Centering cone 74-99,5 mm 404,00 A 150 xx0 011 Centering cone 44-80 mm 426,00 A 150 xx0 012 Centering cone 74-111,5 mm 453,00 A 150 xx0 020 2-cone set 44-111,5 mm (011 / 012) 701,00 A 150 xx0 021 3-cone set 42-99,5 mm (008 / 009 / 010) 891,00 A 150 xx0 022 Centering cone 168,5-194,5 mm 1.777,00 A 150 xx0 024 Centering cone 198-225 mm / only with Plastic Spacer disc 190 xx0 042 1.290,00 A 150 xx0 025 Centering cone for trucks 277,4-283 mm 1.612,00 A 150 xx0 026 Set of light truck cones 88-174 mm (043 / 049 / 190 xx0 018) 2.301,00 A 150 xx0 043 Centering cone 122-174 mm 1.268,00 A 150 xx0 047 Centering cone 43.5-70 mm 293,00 A 150 xx0 048 Centering cone 68-98 mm 389,00 A 150 xx0 049 Centering cone 88-132mm 701,00 A 150 xx0 072 Centering Cone 137-140,5mm Ford Transit from 1995 975,00 A 150 xx0 074 Centering Cone 128-131,5 mm Iveco from 1997 975,00 Side 6
A 150 xx0 085 3-Centering cone set 42-111,5 mm (008 / 009 / 012) 990,00 A 150 xx0 091 Centering Cone 122-174mm (043 / 190 xx0 018) 1.765,00 A 150 400 097 Conical ring "A" 56,3-58,2 mm Hofmann 653,00 A 150 400 098 Conical ring "B" 63,1-65,3 mm Hofmann 653,00 A 150 400 099 Conical ring "C" 71,3-74,2 mm Hofmann 653,00 A 150 400 100 Conical ring "D" 58,3-60,5 mm Hofmann 653,00 A 150 400 101 Conical ring "E" 65,8-67,7mm Hofmann 653,00 A 150 400 102 Conical ring "F" 52-56,2 mm Hofmann 653,00 A 150 460 001 Centering cone 95-124 mm 46 mm inside diameter 701,00 A 150 460 011 Centering cone 48-80 mm 46 mm inside diameter 346,00 A 150 460 012 Centering cone 74-111.5 mm 46 mm inside diameter 453,00 A 150 460 024 Centering cone 198-225 mm, truck, 46 mm inside diameter 1.268,00 A 150 460 025 Centering cone 277,4-283 mm, truck, 46 mm inside diameter 1.613,00 A 150 460 043 Centering cone 122-174 mm 46 mm inside diameter 1.328,00 A 150 460 049 Centering cone 88-132mm 46 mm inside diameter 701,00 Side 7
A 150 460 091 Centering cone 122-174 mm ( 043 / 190 460 018) 1.765,00 Side 8
Centering sleeve Enter diameter of the balancer shaft as 4th and 5th number (28, 36, 38, 40) A 160 xx0 004 Centering sleeve 63.25 / 63.5 mm 653,00 A 160 xx0 006 Centering sleeve 58 / 65 mm 653,00 A 160 xx0 008 Centering sleeve OPEL 56.5 / 65 mm 653,00 A 160 xx0 009 Centering sleeve Porsche 959 653,00 A 160 xx0 011 Centering sleeve 55 / 60 / 65 mm 653,00 A 160 xx0 012 Centering sleeve 54 / 60 / 64 mm 653,00 A 160 xx0 027 Centering sleeve Rolls Royce (-`95) 72,5 mm 653,00 A 160 xx0 028 Centering sleeve Rolls Royce 117,55 mm (old) 653,00 A 160 xx0 029 Centering sleeve OPEL 57 / 70,2 mm 653,00 A 160 xx0 030 Centering sleeve Toyota 110,05 mm 1.133,00 A 160 xx0 031 Centering sleeve BMW 57 / 72,5 / 74 mm 653,00 A 160 xx0 032 Centering sleeve 56 / 66 / 71,5 mm 653,00 A 160 xx0 051 Centering sleeve Mercedes 66,7 / 84-85 mm 653,00 A 160 xx0 053 Centering sleeve Toyota / Nissan Off Road 106 / 110 mm 1.133,00 Side 9
Wire Wheel Kits B 162 400 001 Centering kit for spoke wheels with central locker, 40 mm 3.100,00 B 162e400 001 Cone for Austin Martin DB 6, Jaguar, Triumph, Austin Healy 870,00 B 162e400 002 Centering ring, conical for Jaguar, Triumph, Austin Healy 983,00 B 162e400 003 Centering ring, conical for Austin Martin DB 6, old Jaguar 983,00 Pneumatic Handles A 163 008 007 Pneumatic handle Hofmann, JBC, Sicam P Power Clamp for clamping hood 805,00 A 163 588 004 Pneumatic handle Cemb P for clamping hood (36 mm) 805,00 A 163 589 004 Pneumatic handle Cemb & Tip Top P, Ravaglioli P for clamping hood (40 mm) DuoExpert Enter diameter of the balancer shaft as 4th and 5th number (28, 36, 38, 40) 805,00 A 164 xx0 500 DuoExpert System. 2 collets in a case 54-75mm. 5.660,00 A 164 xx0 501 DuoExpert collet 54-65 mm clamping range 2.915,00 A 164 xx0 502 DuoExpert collet 64-75 mm clamping range 2.915,00 A 164 xx0 505 DuoExpert collet 71-82 mm clamping range 2.915,00 A 164 xx0 507 DuoExpert collet 74-85 mm clamping range 2.915,00 A 164 xx0 509 DuoExpert collet 62-73 mm clamping range 2.915,00 Side 10
Spare parts for DuoExpert B 164e008 011 Rubber ring DuoExpert 135,00 B 164e008 101 Basic collet DuoExpert 40 mm inside diameter 1.645,00 B 164e008 102 Basic collet DuoExpert 38 mm inside diameter 1.645,00 B 164e008 103 Basic collet DuoExpert 36 mm inside diameter 1.645,00 B 164e008 104 Basic collet DuoExpert 35 mm inside diameter 1.645,00 B 164e008 105 Basic collet DuoExpert 30 mm inside diameter 1.645,00 B 164e008 106 Basic collet DuoExpert 28.56 mm inside diameter 1.645,00 B 164e008 110 Synchronizing ring DuoExpert 353,00 B 164e008 111 Expanding segment DuoExpert collet 54-65 mm 353,00 B 164e008 112 Expanding segment DuoExpert collet 64-75 mm 353,00 Threaded Shafts A 170 588 000 Threaded shaft Tr 36x3mm Cemb / Rav / Teco 200mm extra long with screw M10 1.155,00 A 170 589 001 Threaded shaft Tr 40x4mm Cemb & TipTop 190 mm long with screw M10 1.155,00 A 170 627 008 Threaded shaft 38x3mm Fasep 180 mm Long, connection M22 x 1,5 1.155,00 A 170 657 001 Threaded shaft Tr28.55x3 mm fits Mondolfo MT 1000-8000, 200 mm long, connection M12 1.155,00 Side 11
A 170 658 001 Threaded shaft Tr40x3 mm Mondolfo MT 1000-8000 with screw M12 1.155,00 A 170 658 003 Threaded shaft Tr40x3 mm Mondolfo (truck) Far East with screw M12 1.155,00 A 170 907 004 Threaded shaft Tr38x3 mm Corghi/Faip/Sice 215 mm long with screw M15 x 1,5 1.155,00 A 170 907 007 Threaded shaft Tr 40x3 Mondolfo 181 mm long with screw M15 x 1,5 1.155,00 A 170 928 001 Threaded shaft Tr 40x3 mm HAWEKA/BM 22/44/55/550 with screw M16 1.155,00 A 170 937 001 Threaded shaft fits Coats. Thread 28,55 x3 mm. 170mm long Connection 5/8" - 11 UNC 1.155,00 A 170 937 002 Threaded shaft Tr40x3 mm Coats 850/950/1050 connenction 5/8"-11 UNC 1.155,00 A 170 957 002 Threaded shaft Tr28,55x3 mm Balco/Sun/Snap-on, extra long version, 200 mm, connection 3/8"-24 UNF 1.155,00 A 170 957 011 Threaded shaft Tr28.55x3.5, John Bean, 186 mm, connection 3/8"-24 UNF 1.155,00 A 170 958 001 Threaded shaft Tr40x3 mm Balco with screw 3/8"-24 UNF 1.155,00 A 170 958 002 Threaded shaft Tr40x4 mm Snap On/JBC USA with screw 3/8"-24 UNF 1.155,00 A 170 958 006 Threaded shaft Tr40x3 Balco/JBC line 9000 300 mm long connection M33 x 2 1.760,00 A 170 988 001 Threaded shaft Tr40x3, 260 mm Cemb, with screw M10 1.155,00 A 170e658 001 Screw M12 for 40 mm Threaded shaft MT 1000-6000 113,00 A 170e958 002 Screw for Threaded shaft 3/8"-24UNF Balco thread 40x3 mm (170 958 001) 113,00 Side 12
Clamping Hoods / Spacer Discs & Springs Enter diameter of the balancer shaft as 4th and 5th number (28, 36, 38, 40) A 190 008 002 Clamping hood fits ALL Haweka wing nuts 233,00 A 190 008 005 Rubber cap for clamping hood 190 008 002 54,00 A 190 008 021 Large diameter (220mm) clamping hood for alloy rims. Suits ALL Haweka wing nuts 465,00 A 190 008 025 Large diameter (220mm) clamping hood for alloy rims. Suits CEMB orig. wing nuts 675,00 A 190 008 027 Pressure ring, fits ALL Haweka wing nuts 54,00 A 190 008 028 Large diameter (220mm) clamping hood for alloy rims. Suits Hofmann orig. wing nuts 675,00 A 190 008 029 Large diameter (220mm) clamping hood for alloy rims. Suits Corghi orig. wing nuts 675,00 A 190 280 015 Spring, conical for open MCD 54,00 A 190 400 008 Special pressure piece for Porsche 425,00 A 190 400 015 Spring, conical for open MCD, DuoExpert 67,00 A 190 658 001 Steel spacer Mondolfo 1.530,00 Side 13
A 190 905 001 Steel spacer Corghi 1.530,00 A 190 958 001 Steel spacer Balco 1.530,00 A 190 988 002 Steel spacer Cemb / Haweka 1.530,00 A 190e008 047 Distance ring with magnets for Off-Road cone from the back incl. Pins 1.365,00 A 190 xx0 010 (Polyamid) Spacer DuoExpert 90,00 A 190 xx0 018 Aluminium Spacer disc 945,00 A 190 xx0 042 Polyamid Spacer disc / for Centering cone 150 xx0 024 825,00 A 190exx0 045 Polyamid spacer (donut) for Off-Road 105,00 Flange Plates WORLD KIT Flange Plates WORLD KIT (Ø 11 mm) Enter diameter of the balancer shaft as 7th and 8th number (28, 36, 38, 40) A 200 009 xx5 Set of 4 flange adaptors, professional set with 5 sets of studs, colourcoded, 2 wall boards, wallchart, CD-Rom and Off Road Spacer 9.800,00 A 200 009 xx9 A 203 009 405 A 203 009 xx9 A 205 009 xx5 A 205 009 xx9 Off Road Set with 2 flange plate adaptors, colour-coded, 2 sets of studs, incl. 1 wall board, wallchart, CD Rom and Off Road Spacer Set of 4 flange plate adaptors, professional set, colour coded with 5 sets of studs, 2 wall boards, wallchart, CD-Rom and Off Road Spacer for Hofmann "Power Clamp" Off Road Set with 2 flange plate adaptors, colour-coded, 2 sets of studs, incl. 1 wall board, wallchart, CD Rom and Off Road Spacer,suits Hofmann "Power Clamp" Set of 4 flange plate adaptors, colour-coded with 5 sets of studs, 2 wall boards, wall chart, CD Rom and Off Road Spacer for Cemb/Tip Top (36 or 40 mm) Off Road Set with 2 flange plate adaptors, colour-coded, 2 sets of studs, incl. 1 wall board, wall chart, CD-Rom and Off Road Spacer for Cemb/Tip Top (36 or 40 mm) 6.200,00 12.400,00 7.500,00 12.400,00 7.500,00 Side 14
Flange Plates / Studs / Special Sets Flange Plates Series WORLD KIT (Ø 11 mm) w/o studs A 241e801 xx9 Flange Plate Adaptor (TSP No. 1), colour-coded, without studs 4x95,25/ 4x98/ 4x100/ 4x101,6/ 4x108/ 4x114,3/ 7x150/ 4x170 1.485,00 A 251e701 xx9 A 251e901 xx9 A 231e901 xx9 A 243e801 409 Flange Plate Adaptor (TSP No. 2), colour-coded, without studs 5x98/ 5x108/ 5x110/ 5x115/ 5x120,65/ 5x135/ 5x154,95 Flange Plate adaptor (TSP No. 3) Off Road, colour-coded, without studs 5x100/ 5x112/ 5x114,3/ 5x120/ 5x127/ 5x130/ 5x139,7/ 5x150/ 5x165,1 Flange Plate Adaptor (TSP No. 4) Off Road, colour-coded, without studs 3x98/ 3x112/ 3x114,3/ 3x115/ 3x127/ 3x130/ 6x135/ 6x139,7/ 4x165,1 Flange Plates Series WORLD KIT (Ø 11 mm) w/o studs Hoffmann / JBC / Sicam P Flange Plate Adaptor (TSP No. 1), colour-coded, without studs 4x95,25/ 4x98/ 4x100/ 4x101,6/ 4x108/ 4x114,3/ 7x150/ 4x170 1.485,00 1.485,00 1.485,00 2.400,00 A 253e701 409 Flange Plate Adaptor (TSP No. 2), colour-coded, without studs 5x98/ 5x108/ 5x110/ 5x115/ 5x120,65/ 5x135/ 5x154,95 2.400,00 A 253e901 409 Flange Plate adaptor (TSP No. 3), colour-coded, without studs 5x100/ 5x112/ 5x114,3/ 5x120/ 5x127/ 5x130/ 5x139,7/ 5x150/ 5x165,1 2.400,00 A 233e901 409 A 245e801 409 Flange Plate Adaptor (TSP No. 4), colour-coded, without studs 3x98/ 3x112/ 3x114,3/ 3x115/ 3x127/ 3x130/ 6x135/ 6x139,7/ 4x165,1 Flange Plates Series WORLD KIT (Ø 11 mm) w/o studs Tip Top / Cemb Ø 40 Flange Plate Adaptor (TSP No. 1), colour-coded, without studs 4x95,25/ 4x98/ 4x100/ 4x101,6/ 4x108/ 4x114,3/ 7x150/ 4x170 2.400,00 2.400,00 A 255e701 409 Flange Plate Adaptor (TSP No. 2), colour-coded, without studs 5x98/ 5x108/ 5x110/ 5x115/ 5x120,65/ 5x135/ 5x154,95 2.400,00 A 255e901 409 Flange Plate adaptor (TSP No. 3), colour-coded, without studs 5x100/ 5x112/ 5x114,3/ 5x120/ 5x127/ 5x130/ 5x139,7/ 5x150/ 5x165,1 2.400,00 A 235e901 409 Flange Plate Adaptor (TSP No. 4), colour-coded, without studs 3x98/ 3x112/ 3x114,3/ 3x115/ 3x127/ 3x130/ 6x135/ 6x139,7/ 4x165,1 2.400,00 Side 15
Studs for Flange Plates WORLD KIT (Ø 11 mm) A 271 994 117 Plug-in Stud "I" 100 mm long, Ø 19 mm 189,00 A 271 804 118 Plug-In Stud "II" 80 mm long, short taper, Ø 24,5 mm 189,00 A 271 904 119 Plug-In Stud "III" 90 mm long, rounded head, Ø 24,5 mm 189,00 A 271 804 120 Plug-In Stud "IV" 80 mm long, Range/Land Rover, Ø 34 mm 220,00 A 271 994 121 Plug-In Stud "V" 100mm long, short taper, Ø 22,5 mm 189,00 Special Studs Series WORLD KIT (Ø 11 mm) A 271 124 122 Plug-In Stud "VI", 120 mm long, short taper, Ø 22,5 mm 189,00 A 271 904 112 Plug-In Stud, 90 mm long, Ø 24,4 mm 189,00 A 271 994 308 Plug-In Stud, spring-loaded, 100 mm long, short taper, Ø 24,5 mm 240,00 A 271 008 002 O-rings for plug-in-stud (Ø 11 mm) (set of 5 pcs.) 39,00 Flange Plates STANDARD KIT (Ø 12 mm) Flange Plates for Fixed Studs (w/o studs) (Standard Stud 270 804 014) Enter diameter of the balancer shaft as 7th and 8th number (28, 36, 38, 40) A 240e101 xx2 Flange plate adaptor 4x100, without Studs 835,00 A 240e102 xx0 Flange plate adaptor 4x108, without Studs 835,00 A 240e103 xx0 Flange plate adaptor 4x130, without Studs 835,00 A 240e104 xx0 Flange plate adaptor 4x114.3, without Studs 835,00 A 240e107 xx0 Flange plate adaptor 4x98, without Studs 835,00 Side 16
A 240e108 xx0 Flange plate adaptor 4x101.6, without Studs 835,00 A 240e109 xx0 Flange plate adaptor 4x140, without Studs 835,00 A 250e101 xx0 Flange plate adaptor 5x112, without Studs 835,00 A 250e102 xx0 Flange plate adaptor 5x120, without Studs 835,00 A 250e104 xx0 Flange plate adaptor 5x108, without Studs 835,00 A 250e105 xx0 Flange plate adaptor 5x130, without Studs 835,00 A 250e107 xx0 Flange plate adaptor 5x114.3, without Studs 835,00 A 250e108 xx0 Flange plate adaptor 5x100, without Studs 835,00 A 250e109 xx0 Flange plate adaptor 5x98, without Studs 835,00 A 250e120 xx0 Flange plate adaptor 5x110, without Studs 835,00 A 250e121 xx0 Flange plate adaptor 5x135, without Studs 835,00 A 250e122 xx0 Flange plate adaptor 5x115 Opel Sintra, without Studs 835,00 A 250e129 xx0 Flange plate adaptor 5x150, without Studs 835,00 A 260e101 xx1 Flange plate adaptor 6x139.7, without Studs 835,00 A 260e112 xx0 Flange plate adaptor 6x130 / 6x120, without Studs, Mercedes Benz Sprinter from 01.01.06 835,00 Side 17
Flange Plates Series Light Truck (Ø 12 mm) w/o fixed studs A 211e401 xx2 Flange plate adaptor 5x170 / 190 / 6x170 2.225,00 A 221e201 xx0 Flange plate adaptor 5x160 / 6x180 2.225,00 A 231e403 xx2 Flange plate adaptor 5x203.2/ 205/ 208 -- 6x184.15/ 222.25 2.225,00 A 260e103 xx1 Flange plate adaptor 5/6 x 205 / 6 x 180 2.225,00 Fixed Studs for Flange Plates (Ø 12 mm) A 270 804 003 Fixed stud, short taper 80 mm long, Ø 24,5 mm (recommended standard stud) 169,00 A 270 804 014 Fixed stud, long taper 80 mm long, Ø 25,4 mm 169,00 A 270 354 000 Fixed stud 35 mm long, truck, (Japan ), Ø 39,5 mm 169,00 Special Studs for Flange Plates with Fixed Studs (Ø 12 mm) A 270 804 005 Fixed stud, rounded head 80 mm long, Ø 24,5 mm 189,00 A 270 904 002 Fixed stud, rounded head 90 mm long, Porsche, Ø 24,5 mm 189,00 A 270 904 014 Fixed stud, long taper 90 mm long, Ø 24,5 mm 189,00 A 270 994 002 Fixed stud, rounded head 100 mm long, Porsche, Ø 24,5 mm 189,00 Side 18
Single Flange Plates w/o studs Standard Set - Car Manufacturers - A 201e402 xx0 Flange plate adaptor 3x112/ 5x112/ 130/ 140 Mercedes Benz (recomm. stud 271 804 003) 1.155,00 A 211e201 xx0 Flange plate adaptor 4x100/ 5x120, BMW (spring-loaded studs needed 271 994 208) 1.155,00 A 251e303 xx0 A 231e505 xx3 Flange plate adaptor 5x98/ 108/118 Peugeot/Citroen/Renault (recomm. stud 271 804 003) Single Flange Plates w/o studs Standard Set (Ø 12mm ) Flange plate adaptor Off Road 5x 114,3-5/6x 139,7-4/5x 165,1 (without Studs) 1.155,00 1.155,00 A 241e603 xx0 Flange plate adaptor 4 x 98 / 100 / 108 / 110 / 114.3 / 120 (without Studs) 1.155,00 A 251e603 xx0 Flange plate adaptor 5 x 100 / 108 / 112 / 114,3 / 120 / 130 (without Studs) 1.155,00 A 251e608 xx0 Flange plate adaptor 5 x 98 / 100 / 108 / 112 / 120 / 130 (without Studs) 1.155,00 A 251e611 xx0 Flange plate adaptor 5 x 100 / 108 / 110 / 112 / 120 / 130 (without Studs) Plug-in Studs for Flange Plates (Ø 12 mm) 1.155,00 A 271 804 003 Plug-in stud 80 mm long, short taper, Ø 24,5 mm 184,00 A 271 804 014 Plug-in stud 80 mm long, long taper, Ø 24,5 mm 184,00 A 271 904 002 Plug-in stud, Porsche 90 mm long 184,00 A 271 904 012 Plug-in stud 90 mm long, long taper, Ø 24,5 mm 184,00 A 271 994 016 Plug-in stud 100 mm long, long taper, Ø 22,5 mm 184,00 A 271 994 208 Plug-in stud 100 mm long, spring-loaded, short taper, Ø 24,5 mm 270,00 Side 19
A 271 008 001 O-rings for plug-in-stud (Ø 12 mm) (set of 5 pcs.) 25,00 Special Studs for Flange Plates (Ø 12 mm) A 271 124 002 Plug-in stud 120 mm long, rounded head, Porsche, Ø 24,5 mm 180,00 A 271 124 009 Plug-in stud 120 mm long, long taper, Ø 24,5 mm 180,00 A 271 994 002 Plug-in stud 100 mm long, rounded head, Porsche, Ø 24,5 mm 180,00 A 271 994 012 Plug-in stud 100 mm long, long taper, Ø 24,5 mm 180,00 Flange Plate QuickPlate / Heads QuickPlates Enter diameter of the balancer shaft as 7th and 8th number (28, 36, 38, 40) B 200 456 xx5 Set of QuickPlates (4-, 5 and 6-holes-plate) incl. wall board 14.900,00 B 249 009 xx0 QuickPlate 4-holes with standard heads (4 pcs. 273e008 002) 4.700,00 B 259 009 xx0 QuickPlate 5-holes with standard heads (5 pcs. 273e008 011 + 5 pcs. 273e008 006) 5.600,00 B 269 009 xx0 QuickPlate 6-holes with standard heads (6 pcs. 273e008 003) 6.200,00 QuickPlates PN Hofmann / JBC / Sicam P (for Pneumatic Wheel-Balancing-Machines) B 203 456 405 Set of QuickPlates Hofmann (4-, 5-,6-holes-plate with pneumatic handle) incl. Wall board 16.700,00 B 249 818 401 QuickPlate 4-holes for Hofmann with standard heads (4 pcs no. 273e008 002) and pneumatic handle 4.900,00 B 259 818 401 QuickPlate 5-holes for Hofmann with standard heads (5 pcs 273e008 011 + 5 pcs 273e008 006) and pneumatic handle 5.640,00 B 269 818 401 QuickPlate 6-holes for Hofmann with standard heads (6 pcs no. 273e008 003) and pneumatic handle 6.400,00 Side 20
QuickPlates PN Hofmann / JBC / Sicam P (for Pneumatic Wheel-Balancing-Machines) B 205 456 405 Set of QuickPlates Cemb Ø 40 mm (4-, 5-,6-holes-plate with pneumatic handle) incl. Wall board 16.700,00 B 205 456 365 Set of QuickPlates Cemb Ø 36 mm (4-, 5-,6-holes-plate with pneumatic handle) incl. Wall board 16.700,00 B 249 588 361 QuickPlate 4-holes for Cemb Ø 36 mm with standard heads (4 pcs no. 273e008 002) and pneumatic handle 5.600,00 B 249 589 401 QuickPlate 4-holes for Cemb Ø 40 mm with standard heads (4 pcs no. 273e008 002) and pneumatic handle 5.600,00 B 259 588 361 QuickPlate 5-holes for Cemb Ø 36 mm with standard heads (5 pcs 273e008 011 + 5 pcs 273e008 006) and pneumatic handle 6.200,00 B 259 589 401 QuickPlate 5-holes for Cemb Ø 40 mm with standard heads (5 pcs 273e008 011 + 5 pcs 273e008 006) and pneumatic handle 6.200,00 B 269 588 361 QuickPlate 6-holes for Cemb Ø 36 mm with standard heads (6 pcs no. 273e008 003) and pneumatic handle 6.400,00 B 269 589 401 A 207 400 000 QuickPlate 6-holes for Cemb Ø 40 mm with standard heads (6 pcs no. 273e008 003) and pneumatic handle FixPlates Set of 4 FixPlate, colour-coded, with 10 studs, 25 heads for studs, 1 wall boards, wallchart 6.400,00 11.235,00 A 247 701 407 FixPlate (No. 1), colour-coded, without studs 4x98/ 4x100/ 4x101,6/ 4x108/ 4x114,3/ 7x150/ 4x170 1.945,00 A 257 701 407 FixPlate (No. 2), colour-coded, without studs 5x98/ 5x108/ 5x110/ 5x115/ 5x120,65/ 5x135/ 5x154,95 1.945,00 A 257 901 407 FixPlate ( No. 3) Off Road, colour-coded, without studs 5x100/ 5x112/ 5x114,3/ 5x120/ 5x127/ 5x130/ 5x139,7/ 5x150/ 5x165,1 1.945,00 A 237 901 407 FixPlate (No. 4) Off Road, colour-coded, without studs 3x98/ 3x112/ 3x114,3/ 3x115/ 3x127/ 3x130/ 6x135/ 6x139,7/ 4x165,1 Stud for Flange Plate FixPlate 1.945,00 A 274 008 001 Plug-in stud for FixPlate without head 220,00 Side 21
Heads B 273e008 002 Head, short taper, length head 28 mm, Ø 24,5 mm 89,00 B 273e008 003 Head, short taper, length head 38 mm, Ø 24,5 mm 89,00 B 273e008 006 Head, rounded, length head 38 mm, Ø 24,5 mm 89,00 B 273e008 011 Head, long taper, length head 48 mm, Ø 22,5 mm 89,00 Special Heads B 273e008 004 Head, short taper, length head 48 mm, Ø 24,5 mm 89,00 B 273e008 007 Head, rounded, length head 48 mm, Ø 24,5 mm 89,00 B 273e008 008 Head, Range-, Landrover, length head 28 mm, Ø 34 mm 89,00 B 273e008 023 Head, long taper, length head 55,6 mm, Ø 19,0 mm 89,00 B 273e008 025 Head, long taper, length head 58 mm, Ø 22,5 mm 89,00 Special Adaptor Kits / Reducing Sleeves Special Adaptor Kits A 280 280 025 Centering kit Porsche, inside diameter 28 mm 3.370,00 A 280 400 025 Centering kit Porsche, inside diameter 40 mm 3.370,00 A 280 280 008 Professional 4 X 4 kit. 5/6 X 139.7 & 5 X 165.1, Ø 28 mm 4.200,00 A 280 400 008 Professional 4 X 4 Kit. 5/6 X 139.7 & 5 X 165.1, Ø 40 mm 4.200,00 A 280 400 055 Centering kit for Quad-rims 1.845,00 Side 22
A 280 400 061 LLkw Adapter for VW Crafter / MB Sprinter Ø 205 3.460,00 Reducing Sleeves A 290 280 001 Reducing sleeve 40 mm to 28 mm 50 mm long 195,00 A 290 300 001 Reducing sleeve 40 mm to 30 mm 50 mm long 195,00 A 290 350 001 Reducing sleeve 40 mm to 35 mm 50 mm long 195,00 A 290 360 001 Reducing sleeve 40 mm to 36 mm 50 mm long 195,00 A 290 380 001 Reducing sleeve 40 mm to 38 mm 50 mm long 195,00 Universal Clamping Devices UniEurop Universal Adaptors A 300 008 103 UniEurop with standard nuts, 5 bolts M10 4.735,00 A 370 008 003 Threaded sliding stud M10 x 1,25 55 mm long, for UniEurop 236,00 Centering Rings Series 300 and UniLug 400 A 360 008 001 Centering ring 58 mm fits HAWEKA universal adaptors 355,00 A 360 008 002 Centering ring 60 mm fits HAWEKA universal adaptors 355,00 A 360 008 004 Centering ring 65 mm fits HAWEKA universal adaptors 355,00 A 360 008 005 Centering ring 55 mm fits HAWEKA universal adaptors 355,00 A 360 008 006 Centering ring 56 mm fits HAWEKA universal adaptors 355,00 Side 23
UniLug / Series 400 + 405 UniLug Series 405 (incl. 3 Centering rings, 58,60, 65 mm) A 405 009 108 UniLug without clamping chuck e.g. for machines with cylindrical shafts 4.935,00 A 405 280 108 UniLug for machines with 28,56 mm shaft, Mondolfo, Balco, Snap On, US-Market 4.935,00 A 405 360 108 UniLug for machines with 36 mm shaft, Cemb, Ravaglioli 4.935,00 A 405 380 108 UniLug for machines with 38 mm shaft, Corghi, Faip, Sice, HPA incl. Spacer 405e008 004 4.935,00 A 405 381 108 UniLug for machines with 38 mm shaft, Fasep 4.935,00 A 405 400 108 UniLug for machines with 40 mm shaft, TipTop, Cemb, Ravaglioli, US- Market, Mondolfo (2005/06), Hunter 9200 4.935,00 A 405 401 108 UniLug for machines with 40 mm shaft, Corgi, HPA, Teco, Mondolfo ( from 2007) incl. Spacer 405e008 004 4.935,00 A 405 818 108 UniLug for machines with conical shaft, Beissbarth, Sicam, Facom, Hofmann, Schenck 5.200,00 A 405e008 004 UniLug Spacer for Corghi, Faip, Sice, HPA, Mondolfo TECO 705,00 A 405e280 001 UniLug Adaptor ring Ø 28 mm 390,00 A 405e360 001 UniLug Adaptor ring Ø 36 mm 390,00 A 405e380 001 UniLug Adaptor ring Ø 38 mm 390,00 A 405e400 001 UniLug Adaptor ring Ø 40 mm 390,00 Side 24
Centering Rings series 405 A 405e009 001 Centering ring 58 mm 390,00 A 405e009 002 Centering ring 60 mm 390,00 A 405e009 004 Centering ring 65 mm 390,00 A 405e009 005 Centering ring 55 mm upon request 390,00 A 405e009 006 Centering ring 56 mm by request 390,00 Spare Parts for UniLug Series 400 and 405 A 405e008 006 Control disc UniLug II (plastic) 180,00 A 400e008 021 Complete lug for UniLug without chuck (series 405) 506,00 A 400e008 023 Fit screw UniLug II (serie 405) height of head 2,5 mm 99,00 A 400e008 050 Fit screw UniLug II (serie 405) height of head 3,2 mm 99,00 A 400e008 027 Knurled nut for lug 400e008 041 55,00 A 400e008 041 Complete lug for UniLug series 400, conical 475,00 A 400e818 001 Knurled nut M14x1.5 for Hofmann Geodyna Power Clamp 105,00 A 400e818 002 Knurled nut M14 for Hofmann P (AIR) 105,00 A 490 008 000 PCD tool for UniLug 240,00 Side 25
B 490 008 001 PCD measuring tool 685,00 Nuts and Fixcones A 040 100 001 Set of fixcones (5 pieces) M10x1,25 mm (Haweka) 1.615,00 A 040 100 002 Set of fixcones (5 pieces) M10x1,5 mm (Corghi/Cemb) 1.615,00 A 040 100 003 Single Fixcone M10x1,25 mm (Haweka) 390,00 A 040 100 004 Single Fixcone M10x1,5 mm (Corghi/Cemb) 390,00 A 040 100 102 Fastening nut M10x1,25 mm round and cone head (Haweka) (1 pcs.) 55,00 A 040 100 112 Fastening nut M10x1,25 mm extra long, round head, new Peugeots (1 p 68,00 A 040e008 004 Pressure piece for fixcone round head 68,00 A 040e008 005 Pressure piece for fixcone conical 68,00 Centering Rings for Original Hofmann Universal Adaptors A 060 818 001 Centering ring 58 mm fits original Hofmann Universal Adaptors 390,00 A 060 818 002 Centering ring 60 mm fits original Hofmann Universal Adaptors 390,00 A 060 818 004 Centering ring 65 mm fits original Hofmann Universal Adaptors 390,00 A 060 818 005 Centering ring 55 mm fits original Hofmann Universal Adaptors 390,00 A 060 818 006 Centering ring 56 mm fits original Hofmann Universal Adaptors 390,00 Side 26
Truck Clamping Devices Truck Adaptors - Kits A 700 589 172 Truck Adapter Kit Cemb 40 7.710,00 A 700 658 174 Truck adaptor kit Mondolfo 8.880,00 A 700 818 172 Truck adaptor kit Hofmann Geodyna 20 L, B 9200 9.435,00 A 700 905 174 Truck adaptor kit Corghi ET 76/86, Faip, Sice 9.435,00 A 700 988 174 Truck adaptor kit Cemb P 200/GS 902 9.435,00 A 702 658 173 Truck/light truck adaptor kit Mondolfo with spacer 12.765,00 A 702 818 172 Truck/light truck adaptor kit Hofmann Geodyna 20 L, B 9200 12.205,00 A 702 818 175 Truck/light truck adaptor kit Sicam / Beissbarth / Facom 12.765,00 A 702 905 172 Truck/light truck adaptor kit Corghi ET 76/86, Faip, Sice 12.205,00 A 702 958 174 Truck/light truck adaptor kit Balco 92/920 12.765,00 A 704 658 172 Truck/light truck adaptor kit Mondolfo, Far East Version 8.325,00 A 704 905 172 Truck/light truck adaptor kit Corghi, Faip, Sice, Far East Version 8.325,00 A 705 589 172 Truck/light truck adaptor kit Cemb 40 12.535,00 A 705 987 172 Truck/light truck adaptor kit Cemb / Tip Top 14.265,00 Side 27
A 710 905 132 Light truck adaptor kit Corghi ET 76/86 Faip, Sice 3.510,00 A 710 958 133 Light truck adaptor kit Balco 920 5.005,00 Truck Adaptors - Spare parts A 700 008 003 Centering Bolt & Nut Truck (stundard) 220,00 A 700 008 004 Centering Bolt & Nut Truck (Dynaf) 220,00 A 700 008 005 Centering Bolt & Nut Truck (IFA) 220,00 A 700 008 006 Centering Bolt & Nut Truck (Alloy wheels) 220,00 A 700 008 013 Centering Bolt & Nut Truck (3 arm star Far East) 220,00 A 700 008 018 Centering Bolt & Nut Truck (3 arm star Europe) 220,00 A 700 400 004 5-arm clamping star truck incl. bolts (700 008 003) Circle Diameter: 225 / 285 / 335 mm 3.120,00 A 700 400 005 4-arm clamping star truck incl. bolts (700 008 003) Circle Diameter: 275 / 285 mm 2.505,00 A 700 400 007 3-arm clamping star incl. bolts Europe (700 008 018) Circle Diameter: 170 / 184,15 / 205 / 222,25 / 245 mm 1.897,00 A 700 400 008 3-arm clamping star truck incl. bolts Far East (700 008 013) Circle Diameter: 170 / 184,15 / 205 / 222,25 / 245 mm 1.897,00 A 700e008 009 Knurled nut for truck adaptor M16 69,00 A 840e100 001 Knurled nut for truck adaptor M10 55,00 A 700e400 004 5-arm clamping star truck standard w/o bolts Circle Diameter: 225 / 285 / 335 mm 2.640,00 Side 28
A 700e400 005 4-arm clamping star truck standard w/o bolts Circle Diameter: 275 / 285 mm 2.185,00 A 700e400 006 5-arm clamping star truck Far East w/o bolts Circle Diameter: Ø12 (203,2 / 208 mm), Ø16 (285,75 / 335 mm) 2.640,00 A 700e400 008 3-arm clamping star truck w/o bolts Circle Diameter: 170 / 184.15 / 205 / 222.25 / 245 1.615,00 A 700e460 004 5-arm clamping star truck Standard w/o bolts Circle Diameter: 225 / 285 / 335 mm 2.640,00 A 700e460 005 4-arm clamping star truck Standard w/o bolts Circle Diameter: 275 / 285 mm 2.185,00 A 700e905 012 Basic truck adaptor II Corghi/Faip/Sice Ø 46 mm 2.785,00 A 700e958 012 Basic truck adaptor II Balco/Hofmann, Sicam, Cemb, Bessbarth Ø 40 mm 2.785,00 A 700e958 013 Basic truck adaptor II Far East Ø 40 mm 2.785,00 A 70Be958 007 Truck Centering ring 220.8 mm 1.598,00 A 70Be958 008 Truck Centering ring 219.9 mm 1.598,00 Trilex and Dayton Adaptors A 725 400 001 Trilex Adaptor 20" / 24", Fisher / Dayton 7.718,00 A 725 400 002 Trilex Adaptor 20" / 22,5" / 24", Europa 7.718,00 A 725 460 001 Trilex Adaptor 20" / 24", Fisher / Dayton 7.718,00 A 725 460 002 Trilex Adaptor 20" / 22,5" / 24", Europa 7.718,00 Side 29
Motorcycle Clamping Devices - Series 805 Motorcycle Clamping Device - for conical shafts A 805 818 010 ProBike II Modular System ECO 4.650,00 A 805 818 011 ProBike II Modular System BASIC 5.500,00 A 805 818 000 ProBike II Modular System STANDARD 6.650,00 A 805 818 001 ProBike II Upgrade Kit Modular System PROFESSIONAL 4.905,00 A 805 818 002 ProBike II Upgrade Kit Modular System EXPERT 6.955,00 Motorcycle Clamping Device - Power Clamp A 805 995 000 ProBike II Modular System STANDARD 6.850,00 A 805 995 001 ProBike II Upgrade Kit Modular System PROFESSIONAL 5.200,00 Motorcycle Clamping Device - cylindrical shafts 28 mm A 805 280 010 ProBike II Modular System ECO 4.650,00 A 805 280 011 ProBike II Modular System BASIC 5.500,00 A 805 280 000 ProBike II Modular System STANDARD 6.650,00 ProBike II Upgrade Kit System PROFESSIONAL / EXPERT go to 805 008 001-002 Side 30
Motorcycle Clamping Device - cylindrical shafts 36 mm A 805 360 010 ProBike II Modular System ECO 4.650,00 A 805 360 011 ProBike II Modular System BASIC 5.500,00 A 805 360 000 ProBike II Modular System STANDARD 6.650,00 ProBike II Upgrade Kit System PROFESSIONAL / EXPERT go to 805 008 001-002 Motorcycle Clamping Device - cylindrical shafts 38 mm A 805 380 010 ProBike II Modular System ECO 4.650,00 A 805 380 011 ProBike II Modular System BASIC 5.500,00 A 805 380 000 ProBike II Modular System STANDARD 6.650,00 ProBike II Upgrade Kit System PROFESSIONAL / EXPERT go to 805 008 001-002 Motorcycle Clamping Device-cylindrical shafts 40 mm Cemb, TipTop, Hofmann Megaplan, Hunter (not Serie 9700) A 805 400 010 ProBike II Modular System ECO 4.650,00 A 805 400 011 ProBike II Modular System BASIC 5.500,00 A 805 400 000 ProBike II Modular System STANDARD 6.650,00 ProBike II Upgrade Kit System PROFESSIONAL / EXPERT go to 805 008 001-002 Side 31
Motorcycle Clamping Device-cylindrical shafts 40 mm Corghi, Mondolfo, Teco, HPA ( from 2007) A 805 401 010 ProBike II Modular System ECO 4.650,00 A 805 401 011 ProBike II Modular System BASIC 5.500,00 A 805 401 000 ProBike II Modular System STANDARD 6.650,00 ProBike II Upgrade Kit System PROFESSIONAL / EXPERT go to 805 008 001-002 Motorcycle Upgrade Kit - cylindrical shafts 28-40 mm A 805 008 001 ProBike II Modular System PROFESSIONAL 4.905,00 A 805 008 002 ProBike II Modular System EXPERT 6.950,00 Motorcycle Clamping Device - special connections A 805 978 000 ProBike II Modular STANDARD Facom U47/87/97 6.975,00 A 805 979 000 ProBike II Modular STANDARD Facom U300 (M12) 6.975,00 A 805 988 000 ProBike II Modular STANDARD for Cemb CB 114 / C34 6.975,00 Motorcycle Upgrade Kit - special connections A 805 978 001 ProBike II Modular PROFESSIONAL Facom U47/87/97 5.200,00 A 805 979 001 ProBike II Modular PROFESSIONAL Facom U300 (M12) 5.200,00 A 805 988 001 ProBike II Modular PROFESSIONAL for Cemb CB 114 / C34 5.200,00 Side 32
Spares and accessories Motorcycle adaptors Series 802 A 802 008 010 Scooter adaptors (2 pcs.) suits ProBike motorcycle adaptor kit 488,00 B 802e008 008 Gas pressure spring series 802 (200 N) 429,00 B 802e008 090 Set of cantilevers (2 pcs.) ProBike Series 802 1.635,00 A 840e100 001 Knurled nut M10 motorcycle shafts 10 and 12 mm 55,00 A 840e140 001 Knurled nut M14 motorcycle shafts 14 mm or more 55,00 Spares and Accessories Motorcycle Adaptors Series 805 A 800e008 003 Conical chuck Facom motorcycle adaptors (old) 1.290,00 A 800e008 002 Basic motorcycle adaptor Cemb/GS/Ammco/Beissbarth (old) Ø 28 mm 945,00 A 800e999 003 Chuck for ProBike base plate, conical 1.290,00 A 800e999 004 Chuck for ProBike base plate, conical (Hofmann P-Version) 1.290,00 A 803e008 003 Chuck for ProBike base plate, Ø 28 mm 945,00 A 803e008 006 Chuck for ProBike base plate, Ø 36 mm 945,00 A 803e008 007 Chuck for ProBike base plate, Ø 38 mm 945,00 A 803e008 008 Chuck for ProBike base plate, Ø 40 mm 945,00 A 803e008 015 Chuck for ProBike base plate, Ø 40 mm, long Version Corgi, Mondolfo, Teco, HPA from 01/07 945,00 Side 33
A 803e008 009 ProBike base plate, complete 2.760,00 A 803e008 010 Set of cantilevers (2 pcs.) - complete replacement set 1.525,00 B DUGA150209 Gas pressure spring series 805 (200 N) 385,00 Spare Parts Series 802 + 805 B 850e190 001 Polyamid pressure piece (19 mm axle) 162,00 A 850 140 006 Set of centering cones 16-45 mm (14 mm axle) 390,00 A 850e140 001 Centering cone (14 mm axle) 75,00 A 860 008 007 Set of centering sleeves 15-28 mm, (14 mm axle) 1.350,00 A 860 008 008 Set of spezial centering sleeves w/o 19 mm shaft 4.210,00 A 860 140 150 Set of centering sleeves 15 mm (14 mm axle) 165,00 A 860 140 160 Set of centering sleeves 16 mm (14 mm axle) 165,00 A 860 140 170 Set of centering sleeves 17 mm (14 mm axle) 165,00 A 860 140 190 Set of centering sleeves 19 mm (14 mm axle) 165,00 A 860 140 200 Set of centering sleeves 20 mm (14 mm axle) 165,00 Side 34
A 860 140 220 Set of centering sleeves 22 mm (14 mm axle) 165,00 A 860 140 250 Set of centering sleeves 25 mm (14 mm axle) 165,00 A 860 140 261 Set of centering sleeves 26 mm (14 mm axle) 165,00 A 860 140 280 Set of centering sleeves 28 mm (14 mm axle) 165,00 A 860 140 300 Set of centering sleeves 30 mm (14 mm axle) 165,00 A 860 141 005 Adaptor Kit BMW (14 mm axle) 735,00 A 860 190 007 Adaptor kit HARLEY DAVIDSON (19 mm axle) 75,00 A 860 190 009 Adaptor kit SUZUKI GSX R centering sleeves 25, 28, 32 mm (19 mm axle) 638,00 A 860 190 012 Adaptor kit Aprilia RST Futura, BMW F 650 CS (19 mm axle) 555,00 A 860 190 014 Adaptor kit Harley Davidson V Rod (19 mm axle) Ø 25,4 mm 270,00 A 860 190 220 Set of centering sleeves 22 mm (19mm axle) 270,00 A 860 190 240 Set of centering sleeves 24 mm (19mm axle) 270,00 A 860 190 250 Set of centering sleeves 25 mm (19mm axle) 270,00 A 860 190 280 Set of centering sleeves 28 mm (19mm axle) 270,00 Side 35
A 860 190 300 Set of centering sleeves 30 mm (19mm axle) 270,00 A 860 190 320 Set of centering sleeves 32 mm (19mm axle) 270,00 A 860 190 350 Set of centering sleeves 35 mm (19mm axle) 270,00 A 860 818 002 Set of screws (4 pcs.) for centering adaptor BMW 355,00 A 860e120 002 Spacer, short, 12 mm inside diameter 55,00 A 860e140 006 Polyamid pressure piece Honda/BMW (14 mm axle) 555,00 A 860e140 460 Centering sleeve Piaggio X9 rear wheel 46 mm (14 mm axle) 310,00 A 860e141 005 Centering sleeve BMW-K 100 SUITS (14 mm axle) 429,00 A 860e150 002 Spacer, short, 15 mm inside diameter 55,00 A 860e180 002 Spacer, short, 18 mm inside diameter 55,00 A 860e190 004 Adaptor Ducati, Triumpf (19 mm axle) 439,00 A 860e190 008 Adaptor HONDA NTV 650 + Goldwing 1800 (19 mm axle) 520,00 A 860e190 011 Centering sleeve MV Agusta Backwheel (19 mm axle) 480,00 A 860e190 012 Centering sleeve Aprilia / BMW / Yamaha (19 mm axle) 450,00 A 860e200 002 Spacer, short, 20 mm inside diameter 55,00 Side 36
A 860e250 002 Spacer, short, 25 mm inside diameter 55,00 A 860e280 002 Spacer, short, 28 mm inside diameter 55,00 A 990e008 001 Face spanner for knurled nuts and the like 75,00 Centering Shafts for MWCD Series 805 768 000 A 870 007 140 14 mm centering shaft for MWCD cylindrical shaft, gripping length 233 mm 1.088,00 A 870 007 141 14 mm centering shaft for MWCD cylindrical shaft, spec. gripping length 318 mm 1.635,00 A 870 007 190 19 mm centering shaft for MWCD cylindrical shaft, gripping length 233 mm 1.088,00 Centering Shafts for MWCD Series 805 280 000-805 400 000 A 870 010 100 10 mm centering shaft for MWCD, gripping length 193 mm 1.088,00 A 870 010 120 12 mm centering shaft for MWCD, gripping length 193 mm 1.088,00 A 870 010 140 14 mm centering shaft for MWCD, gripping length 233 mm 1.088,00 A 870 010 141 14 mm centering shaft for MWCD, special gripping length 318 mm 1.635,00 A 870 010 150 15 mm centering shaft for MWCD, gripping length 233 mm 1.088,00 A 870 010 160 16 mm centering shaft for MWCD, gripping length 233 mm 1.088,00 A 870 010 170 17 mm centering shaft for MWCD, gripping length 233 mm 1.088,00 A 870 010 190 19 mm centering shaft for MWCD, gripping length 270 mm 1.088,00 Side 37
A 870 010 191 19 mm centering shaft for MWCD, gripping length 365 mm 1.800,00 A 870 010 200 20 mm centering shaft for MWCD, gripping length 233 mm 1.088,00 A 870 010 220 22 mm centering shaft for MWCD, gripping length 233 mm 1.088,00 A 870 010 250 25 mm centering shaft for MWCD, gripping length 233 mm 1.088,00 A 870 010 280 28 mm centering shaft for MWCD, gripping length 278 mm 1.088,00 Centering Shafts MWCD Hofmann Power Clamp Series 805 A 870 995 140 14 mm centering shaft for MWCD Power Clamp, gripping length 253 mm 1.635,00 A 870 995 190 19 mm centering shaft for MWCD Power Clamp, gripping length 270 mm 1.635,00 Centering Shafts MWCD - Conical Series 805 A 870 997 100 10 mm centering shaft for MWCD conical shaft, gripping length 177 mm 1.088,00 A 870 997 120 12 mm centering shaft for MWCD conical shaft, gripping length 177 mm 1.088,00 A 870 997 140 14 mm centering shaft for MWCD conical shaft, gripping length 233 mm 1.088,00 A 870 997 141 14 mm centering shaft for MWCD conical shaft, special gripping length 302 mm 1.635,00 A 870 997 150 15 mm centering shaft for MWCD conical shaft, gripping length 233 mm 1.088,00 A 870 997 160 16 mm centering shaft for MWCD conical shaft, gripping length 233 mm 1.088,00 A 870 997 170 17 mm centering shaft for MWCD conical shaft, gripping length 233 mm 1.088,00 A 870 997 190 19 mm centering shaft for MWCD conical shaft, gripping length 270 mm 1.088,00 Side 38
A 870 997 191 19 mm centering shaft for MWCD conical shaft, gripping length 365 mm 1.800,00 A 870 997 200 20 mm centering shaft for MWCD conical shaft, gripping length 233 mm 1.088,00 A 870 997 220 22 mm centering shaft for MWCD conical shaft, gripping length 233 mm 1.088,00 A 870 997 250 25 mm centering shaft for MWCD conical shaft, gripping length 233 mm 1.088,00 A 870 997 280 28 mm centering shaft for MWCD conical shaft, gripping length 278 mm 1.088,00 Centering Shafts MWCD - various - only Series 802 A 870 587 140 14 mm centering shaft for MWCD Cemb C20/22, gripping length 255 mm 1.088,00 A 870 587 190 19 mm centering shaft for MWCD Cemb C20/22, gripping length 255 mm 1.088,00 A 870 657 140 14 mm centering shaft for MWCD Mondolfo MT 500-8000, gripping length 255 mm 1.088,00 A 870 657 190 19 mm centering shaft for MWCD Mondolfo MT 500-8000, gripping length 255 mm 1.088,00 A 870 907 140 14 mm centering shaft for MWCD Corghi/Faip/Sice, gripping length 253 mm 1.088,00 A 870 907 190 19 mm centering shaft for MWCD Corghi/Faip/Sice, gripping length 253 mm 1.088,00 A 870 937 140 14 mm centering shaft for MWCD Coats, gripping length 261 mm 1.088,00 A 870 937 190 19 mm centering shaft for MWCD fits Coats, gripping length 261 mm 1.088,00 A 870 954 140 14 mm centering shaft for MotSV Balco 9000 / 9450 (M10x1), gripping length 255 mm 1.088,00 A 870 954 190 19 mm centering shaft for MotSV Balco 9000 / 9450 (M10x1), gripping length 255 mm 1.088,00 Side 39
A 870 957 140 14 mm centering shaft for MWCD Balco, gripping length 255 mm 1.088,00 A 870 957 190 19 mm centering shaft for MWCD Balco, gripping length 255 mm 1.088,00 A 870 978 140 14 mm centering shaft for MWCD Facom U47 / U87 / U97, gripping length 233 mm 1.088,00 A 870 978 190 19 mm centering shaft for MWCD Facom U47 / U87 / U97, gripping length 233 mm 1.088,00 A 870 979 140 14 mm centering shaft for MWCD Facom U300, gripping length 232 mm, M 12 1.088,00 A 870 979 190 19 mm centering shaft for MWCD Facom U300, gripping length 232 mm, M 12 1.088,00 A 870 987 140 14 mm centering shaft for MWCD Cemb/Ammco/GS, gripping length 233 mm 1.088,00 A 870 987 190 19 mm centering shaft for MWCD Cemb/Ammco/GS, gripping length 260 mm Clamping Device Quick Fix for Series 802 / 805 1.088,00 A 890 140 001 Quick Fix for 14 mm shaft 930,00 A 890 190 001 Quick Fix for 19 mm shaft 930,00 Side 40
Wheel Alignment Clamps and Accessories ProClamp STANDARD (with spring-loaded feet) A 912 008 543 Set: (4 pieces) ProClamp without shafts 15.840,00 ProClamp PLUS (with spring-loaded feet) A 918 579 543 Set: (4 pieces) ProClamp for Optp Plus 15.840,00 A 918 608 543 Set: (4 pieces) ProClamp for Bear 15.840,00 A 918 618 543 Set: (4 pieces) ProClamp PLUS for Hunter incl. attachment shafts 15.840,00 A 918 827 543 Set: (4 pieces) ProClamp for JBC/FMC V3 15.840,00 A 918 828 543 Set: (4 pieces) ProClamp for JBC V6 / V7 / V8 15.840,00 A 918 829 543 Set: (4 pieces) ProClamp PLUS for JBC V501 / 901 / 3D incl. attachment shafts (for 3D necessary 912 008 096) 15.840,00 A 918 907 543 Set: (4 pieces) ProClamp PLUS for Corghi incl. attachment shafts 15.840,00 A 918 988 543 Set: (4 pieces) ProClamp for Cemb / Ravaglioli / Space 15.840,00 A 918 989 543 Set: (4 pieces) ProClamp PLUS for Cemb New serie W 400 incl. attachment shafts 15.840,00 A 918 998 543 A 925 618 543 Set: (4 pieces) ProClamp PLUS for Beissbarth incl. attachment shafts ProClamp SYNCRO (with spring-loaded feet) Set: (4 pieces) ProClamp Syncro for Hunter incl. attachment shafts 15.840,00 23.065,00 A 925 828 543 Set: (4 pieces) ProClamp Syncro for JBC V6 / V7 incl. attachment shafts 23.065,00 A 925 829 543 Set: (4 pieces) ProClamp Syncro for John Bean V501 / 901 incl. attachment shafts 23.065,00 Side 41
A 925 907 543 Set: (4 pieces) ProClamp Syncro for Corghi incl. attachment shafts 23.065,00 A 925 989 543 Set: (4 pieces) ProClamp Syncro for Cemb New serie W 400 incl. attachment shafts 23.065,00 A 925 998 543 Set: (4 pieces) ProClamp Syncro for Beissbarth incl. attachment shafts Spoiler Adaptors 23.065,00 A 910 618 002 Spoiler Adaptor Hunter DSP 250 / Facom 985,00 A 910 658 001 Spoiler Adaptor Mondolfo Ferro (New) 985,00 A 910 828 011 Spoiler Adaptor FMC/JBC V3 etc. old 985,00 A 910 828 012 Spoiler Adaptor JBC V6/7/8 etc. 985,00 A 910 829 000 Spoiler Adaptor for V 501 / 901 1.155,00 A 910 907 001 Spoiler Adaptor Corghi 985,00 A 910 998 001 Spoiler Adaptor Beissbarth / Sicam / Facom 985,00 Wheel Alignment Shafts for ProClamp B 912e608 001 Shaft Bear 325,00 B 912e618 021 Shaft Hunter DSP 325,00 B 912e819 001 Shaft Hofmann Dynaliner 330 325,00 B 912e827 001 Shaft JBC / FMC Old V3 etc 325,00 Side 42
B 912e828 001 Shaft JBC New V6/7 etc 325,00 B 912e829 001 Shaft V501 / 901 JBC, 3D (necessary 912 008 096) 325,00 B 912e869 001 Shaft HPA 325,00 B 912e907 001 Shaft Corghi / Muller Bem 8676 325,00 B 912e988 003 Shaft Cemb / Rav / Space 325,00 B 912e658 002 Mondolfo / HPA 325,00 B 912e989 001 New Cemb serie W 400 325,00 B 912e998 007 Shaft Beissbarth / Sicam 325,00 Accessories / Spare parts for ProClamp Standard and Syncro B 912 008 012 Upgrade Kit (4 Sets) from ProClamp Standard to Profi: pins, Porsche sleeves and Tool-Box - also for ProClamp Syncro 4.290,00 B 912 008 036 Set of 5 pins 75 mm ProClamp - also for ProClamp Syncro 366,00 B 912 008 037 Set of 5 pins 100 mm ProClamp - also for ProClamp Syncro 366,00 B 912 008 038 Set of 5 pins 115 mm ProClamp - also for ProClamp Syncro 366,00 B 912 008 085 Softline foot (1 piece) Beissbarth, spring-loaded 158,00 B 912 008 086 Softline foot (kit of 12 pieces) Beissbarth, spring-loaded 1.760,00 Side 43
C 912 008 087 Clamping kit for Rims >22" ProClamp with spring-loaded feet (3 pieces) 480,00 B 912 008 094 spring-loaded Feet (kit of 1 piece) for special spoke rims (VW, Ford, Skoda) 140,00 B 912 008 095 spring-loaded Feet (kit of 12 pieces) for special spoke rims (VW, Ford, Skoda) 1.435,00 C 912 008 096 Adapterzapfen ProClamp for John Bean 3D (4 St.) 1.615,00 C 912 008 083 Repair kit spindle grab arm assembly for ProClamp Standard and PLUS 825,00 C 925 008 002 Repair kit spindle grab arm assembly for ProClamp Syncro 875,00 B 912e008 003 plastic feet for 912e008 151 45,00 B 912e008 006 Screw to hold 912e008 151 30,00 B 912e008 007 Softline feet for 912e008 151 45,00 C 912e008 094 Grab arm assembly (Exchange basis only) for ProClamp Standard 1.305,00 C 912e008 277 Grab arm assembly (Exchange basis only) for ProClamp PLUS 1.650,00 C 912e008 227 Grab arm assembly (Exchange basis only) for ProClamp Syncro 1.650,00 C 912 008 097 feet for ProClamp, utility vehicle, L-Lkw (1 piece) 265,00 C 912 008 098 feet for ProClamp, utility vehicle, L-Lkw (6 pieces) 1.450,00 A 912e008 150 Grab arm ProClamp 4x4 270,00 Side 44
A 912e008 151 Foot-receivers 45,00 C 912e008 158 Telescopic Grab Arm for ProClamp 180,00 B 912e008 212 Bracket 180,00 B 912e008 215 Spacer, 54mm, Porsche 488,00 B 912e008 216 Softline Foot (1 piece) ProClamp, spring-loaded 135,00 B 912e008 217 Softline Feet (kit of 12 pieces) ProClamp, spring-loaded (Standard) 1.435,00 B 912e008 244 Centering Sleeve Porsche ProClamp, e.g. Porsche Cayenne (Standard) 488,00 B 912e008 268 ProClamp Adapter for Smart For Four (Circle Diameter 4 x 114,3 mm) 2.160,00 Accessories for VW / Audi / Mercedes B 913 009 024 Inclinometer with case 8.299,00 N 915 000 000 VAG Bridge for alignment on Audi A4/6/8 and Passat B5 7.400,00 Side 45
ProTorks (selling-off) B 950 008 001 ProTork 19 mm, 90 Nm RAL 1021 yellow, 1/2in. Drive 315,00 B 950 008 002 ProTork 17 mm, 110 Nm RAL 3000 red, 1/2in. Drive 315,00 B 950 008 003 ProTork 19 mm, 135 Nm RAL 7001 grey, 1/2in. Drive 315,00 B 950 008 004 ProTork 21 mm, 110 Nm RAL 8003 light brown, 1/2in. Drive 315,00 B 950 008 005 ProTork 19 mm, 110 Nm RAL 5010 blue, 1/2in. Drive 315,00 B 950 008 006 ProTork 13/16" 135 Nm RAL 8014 dark brown, 1/2in. Drive 315,00 B 950 008 007 ProTork 17 mm, 75 Nm RAL 6002 green, 1/2in. Drive 315,00 B 950 008 008 ProTork 21 mm, 80 Nm RAL 9005 black, 1/2in. Drive 315,00 B 950 008 009 ProTork 7/8", 160 Nm RAL 11 white, 1/2in. Drive 315,00 B 950 008 010 ProTork 7/8", 190 Nm RAL 5018 turquoise, 1/2in. Drive 315,00 B 950 008 011 ProTork 19 mm, 75 Nm RAL 5013 dark blue, 1/2in. Drive 315,00 B 950 008 012 ProTork 17 mm, 95 Nm RAL 1001 beige, 1/2in. Drive 315,00 B 950 008 013 ProTork 17 mm, 150Nm Orange, 1/2in. Drive 315,00 B 950 008 014 ProTork 22 mm, 130 Nm Beige, 1/2in. Drive 315,00 B 950 008 015 ProTork 17 mm, 85 Nm fir-green, 1/2in. Drive 315,00 Side 46
B 950 008 020 ProTork holding device (for 5 sticks) 105,00 General Accessories A 900 008 005 Rim width caliper 240,00 A 900 008 006 Wheel weight plier 228,00 A 900 008 027 Run-out measuring device with support 3.675,00 A 900 008 030 Balancing model 1.250,00 A 900 008 040 Special weight application tool 390,00 C 900 008 074 Plug gauge 28/36mm 788,00 C 900 008 075 Plug gauge 38/40mm 788,00 C 900 008 076 Set of plug gauges and measuring forks 3.645,00 C 900 008 103 Shaft gauge (to check the diameter) 28/36mm 1.075,00 C 900 008 104 Shaft gauge (to check the diameter) 38/40mm 1.075,00 A 900 008 106 2 piece wheel weight depressing tool 1.765,00 A 900 008 116 Knee-Pad Set of 4 pcs. 630,00 A 900 008 127 Flange Plate Storage Facility Trolley with perforated plate and 40 mm Ø pins 1.065,00 A 900 008 128 Flange Plate Storage Facility Trolley with tray and 40 mm Ø pins 1.065,00 Side 47
A 900 008 133 Flange Plate Storage Facility Trolley with perforated plate and 28 mm Ø pins 1.065,00 A 900 008 134 Flange Plate Storage Facility Trolley with tray and 28 mm Ø pins 1.065,00 A 900 008 135 Wall Board "PKW" 788,00 A 900 008 136 Wall Board "Off Road" 788,00 A 900 008 142 Wall Board ProBike II "Standard" 788,00 A 900 008 143 Wall Board ProBike II "Profi" 788,00 A 900 008 151 Wall Board QuickPlate 788,00 A 900 008 148 Testing Device for Wheel Balancers 12.955,00 A 900e008 011 Dial gauge 1mm graduation incl. scanning small wheel 2.445,00 A 900e008 089 Scraper to remove stick on alloy weights 98,00 A 900e008 190 Wall Board Stand (wall boards not included) 1.950,00 Side 48
Accessories / Booster C 952 000 001 Booster inflation tank c/w accessories 3.520,00 C 952 000 002 Big Booster inflation tank c/w accessories 4.425,00 A 954 000 001 Wheel mounting aid 355,00 Lifting Device B 916 000 014 Airgo Lift, wheel lifting device for balancers 9.200,00 Spare parts Lifting Device AirgoLift 916 422 710 Bellow -- ** -- 916 422 720 Compressed-Air Connection Bellow -- ** -- 916 422 750 Grooved Ball Bearing -- ** -- 916 423 970 Connection -- ** -- 916 423 980 Compressed-Air Connection of Lower Base Frame -- ** -- 916 510 281 Holding plate for hoop guard -- ** -- 916 510 283 Complete Handle -- ** -- 916 510 286 Roller -- ** -- 916 510 287 Headless Screw of Support Plate -- ** -- 916 510 289 Headless Screw of Base Plate -- ** -- Control Unit 916 012 270 Torsion Spring -- ** -- 916 300 091 Foot Pedal -- ** -- 916 407 600 Compressed Air Connection of Steering Valve -- ** -- 916 422 700 Steering Valve -- ** -- 916 510 291 Spacer -- ** -- Side 49
Wheel Alignment Systems for passenger cars CA-10 C 921 000 001 Wheel alignment system CA-10 complete 27.060,00 CA-10 Wheel Alignment System spares C 913 052 046 Put on scale for ProClamp (rear axle) 810,00 C 921 001 000 Steering wheel adjusting level 810,00 C 900 008 192 Tool stand CA-10 1.635,00 C 913 015 024 Scalesupport (passenger cars) 1.060,00 N Installation fee 1.950,00 CA-10 Wheel Alignment System Accessories C 913 052 068 Magnetic scale support (Passenger cars) 685,00 C 912 008 087 Clamping kit for Rims >22" ProClamp with spring-loaded feet (3 pieces) 480,00 Wheel Alignment Systems for Utility Vehicles TA-20 TA-20 Truck Wheel Alignment System C 922 000 020 Wheel alignment system TA-20-2 complete with new laser heads and Inclinometer 42.500,00 C 922 000 050 Wheel alignment system TA-20-5 complete with new laser heads and Inclinometer with autom. angle identification 48.800,00 C 922 000 001 Upgrade kit for trailer and semitrailer alignment 7.400,00 C 922 000 002 Upgrade kit for alignment of twin steered axles 21.950,00 C 922 000 003 Upgrade kit for passenger cars 9.600,00 Side 50
C 922 000 004 Upgrade kit for special truck rims (Trilex / Dayton) 3.285,00 C 922 000 005 Wheel alignment system for agricultural machines 25.800,00 N Installation fee 3.500,00 TA-20 Truck Wheel Alignment System Accessories B 912 008 036 Set of 5 pins 75 mm, (2 kits = 10 pieces needed) 300,00 B 912 008 037 Set of 5 pins 100 mm, (2 kits = 10 pieces needed) 300,00 B 912 008 038 Set of 5 pins 115 mm, (2 kits = 10 pieces needed) 300,00 C 913 011 000 Turning plate left / right (1 pieces) 2.685,00 C 913 032 003 Adjusting device for measuring heads 4.125,00 C 922 001 004 Frame scale for busses and chassis 8.235,00 TA-20 / HD-20 Truck Wheel Alignment System spares A 912e008 137 Grab arm ProClamp Truck 270,00 C 912e008 140 Grab arm assembly truck (complete) 1.240,00 A 912e008 150 Grab arm (Light truck) 270.135,00 B 912e008 216 Softline Foot (1 piece) ProClamp, spring-loaded 5.450,00 C 913 001 042 Laser head new, for TA-20-2 / -5/ CA-10 405,00 C 913 001 005 Akkupack for Laser head 5.365,00 Side 51
C 913 001 027 Laser head (battery version) 4.210,00 C 913 009 030 Electronic Camber Gauge and base 6.585,00 C 913 009 043 Digital protractor Inclinometer for Ø 40 mm 8.235,00 C 913 009 048 Digital protractor Inclinometer for Ø 40 mm with autom. angle identification 1.050,00 C 913 010 000 Cal block for 913 009 000 2.065,00 C 913 013 000 Magnetic chassis scale 2.065,00 C 913 018 000 T.O.O.T. floor scale, 20 1.650,00 C 913 019 050 Power charger old version (TA-20 with Akku) 990,00 C 913 027 000 100 mm long magnetic foot 460,00 C 913 028 000 215 mm long magnetic foot 460,00 C 913 029 000 265 mm long magnetic foot 540,00 C 913 030 000 315mm long magnetic foot 625,00 C 913 051 000 Scale for toe measurement 3.350,00 Side 52
Wheel Alignment Systems for Utility Vehicles TA-40 TA-40 Truck Wheel Alignment System N 923 000 000 Camera Radio Wheel Alignment System TA-40 incl. Software 285.000,00 C 923 000 001 Upgrade kit for trailer and semitrailer alignment 6.435,00 C 923 000 002 Upgrade kit for alignment of twin steered axles 5.365,00 A 923 000 003 Upgrade kit for passenger cars 7.920,00 C 923 000 004 Upgrade kit for special truck rims (Trilex/Dayton) 3.285,00 N Installation fee 6.900,00 TA-40 Truck Wheel Alignment System Accessories B 912 008 036 Set of 5 pins 75 mm, (2 kits = 10 pieces needed) 300,00 B 912 008 037 Set of 5 pins 100 mm, (2 kits = 10 pieces needed) 300,00 B 912 008 038 Set of 5 pins 115 mm, (2 kits = 10 pieces needed) 300,00 C 913 032 003 Adjusting device for measuring heads 4.125,00 C 923 001 009 Trolley 2.065,00 C 923 001 043 Frame scale new 6.645,00 Side 53
TA-40 Truck Wheel Alignment System spares C 923 001 001 Camera, electronical 45.870,00 C 923 001 002 Transceiver - receiver 12.870,00 C 923 001 003 Accumulator 4,8 Volt 630,00 C 923 001 052 double Battery charger, Power supply, Ciggarette Cable Adapter 12 V 2.468,00 C 923 001 011 Left front scale table, Toe scale TA-40 1.485,00 C 923 001 012 Right front scale table, Toe scale TA-40 1.485,00 C 923 001 013 Left rear scale table, Toe scale TA-40 1.485,00 C 923 001 014 Right rear scale table, Toe scale TA-40 1.485,00 C 923 001 015 Scale right/left (Floor scale) 1.450,00 C 913 052 024 Tripod complete, support for scale toe measuring 1.240,00 C 913 052 025 Support for scale (outer part) 405,00 C 913 052 026 Support for scale (center piece) 405,00 C 913 052 027 Support for scale (inner part) 405,00 C 913 052 028 Support for Magnetic scale 810,00 C 913 052 018 Pins for scales 45,00 Side 54
A 912e008 137 Grab arm ProClamp Truck 270,00 C 912e008 140 Grab arm assembly truck (complete) 1.240,00 A 912e008 150 Grab arm (for light trucks) 270,00 C 912e008 158 Telescopic Grab arm (for passenger cars) 180,00 C 913 027 000 100 mm long magnetic foot 460,00 C 913 028 000 215 mm long magnetic foot 460,00 C 913 029 000 265 mm long magnetic foot 540,00 C 913 030 000 315mm long magnetic foot 625,00 B 912e008 216 Softline Foot (1 piece) ProClamp, spring-loaded 135,00 #VÆRDI! Side 55