ogic Plus Technical technical hotline + (0)68 670 white wiring devices Switchsocket Outlets ogic Plus A socket outlets comply with BS 6: Part : 99. Replacement fuses to the gang socket outlets comply with BS 6: 97. Voltage rating: 0V a.c. Current rating: A per socket outlet (except gang which is amp in total) Terminal capacity: ive, neutral & earth x.mm x mm x 6mm (standard) (Dual earth terminals on list os. K78, K67, K77, K76, K77) Ambient operating temperature: C to +0 C (not to exceed an average of more than C in any hour period) IPXD Max. installation altitude: 000 metres A range of socket outlets designed for ease of installation and having all the advantageous design features of the ogic Plus range. The gang sockets with outboard rockers are of particular value for use by the infirm and partially sighted. on-standard clean earth sockets are for use on installations where restricted access is required and will only accept a 67WHI A non-standard plug with T-shaped earth pin. The sockets have two independent earth terminals so that they can also be used for clean earth installations. K76CE and K97CE also have two independent earth terminals for clean earth installations. A variety of sockets (see ) are fitted with two earth terminals on a common busbar to provide a double earth facility for use when installations require a high integrity protective connection as specified within BS 767: 008. The products can be quickly installed as replacement for existing amp sockets or in a new installation. Fuse carriers ( gang switchsocket only) The fuse carrier is opened by a fast-acting, screwdriver-operated, worm-drive screw for ease of replacement. Round pin sockets A range of round pin sockets is also available, switched and unswitched. BOX TYPES Flush Flush (for extra Surface Insulated Surface Metal wiring space) gang ZIC 6ZIC K0WHI KAM/KAM gang ZIC 8ZIC KWHI KAM/KAM gang KZIC ot available KWHI ot available For a full range of corresponding products, see pages -60 in the product selector.
ogic Plus Technical wiring devices white www.mkelectric.co.uk Switchsocket Outlets Features Moulded on indicator flash on switches will not rub off totally safe Optional neon indicators in the switch rockers with 7 visibility in the horizontal and vertical planes pin operated safety shutter Printed terminal markings on grey rear mouldings for clearer identification Top access, angled terminals make wiring easier and quicker mm minimum switch contact gap Double pole switching Choice of inboard or outboard positioned rockers Additional electrical safety from neutral make first, break last feature Switch contacts with silver contacts on both surfaces for good continuity Only one size of screwdriver required for installation Selection of products incorporating dual earth terminals for high integrity earthing Backed out and captive terminal screws Clean earth sockets available on-standard clean earth sockets available Selected sockets available in graphite finish to assist with Part M compliance Installation ogic Plus socket outlets can be wall or bench mounted. Do not mount or use as a trailing socket or where they may be subject to excessive moisture or dampness. gang switchsocket view from rear Top-facing, angled, backed-out terminals make wiring easier and quicker. Dimensions (mm) gang 0 60. 7 gang 6 0 6 0 0.6 7 0.6 7 Cable management ogic Plus socket outlets can be mounted in a variety of MK trunking systems. gang 06 fuse 80.9 9
rcd protected white red on rcd protected Flag below Reset (R) button. Red : O Black: OFF AWAYS TEST BEFORE USE Press Test (T) button, Red flag should disappear. If it does not, do not use. Press Reset (R) after testing. ogic Plus Technical technical hotline + (0)68 670 white wiring devices Sentrysocket RCD Protected Switchsocket Outlet Compliance with EC Directives, Sentrysockets comply with the following EC Directives and are CE marked: ow Voltage Directive Electromagnetic Compatibility Directive (89/6/EEC) Sentrysocket RCD Single Sockets also comply with the requirements of the following standards: BS 788: 990 BS E 008-: 998 Sentrysocket RCD Double Sockets comply with BS E 6: 996 and BS E 0- Rated Voltage: 0V a.c., 0 or 60Hz Current rating: A resistive Rated tripping current 0mA and 0mA versions Terminal capacity: x mm for gang x mm for gang Ambient operating temperature: C to +0 C IPXD Max. installation altitude: 000 metres Sentrysockets are only suitable for use in T-S system where the Supply eutral Connection is connected to the Supply Earth. They are not suitable for connection across two lines of a 7V line to eutral Voltage System. Sentrysocket provides a high level of protection against electrocution and gives further protection when used with appliances vulnerable to insulation damage, particularly when they are in damp environments or outdoors. Sentrysocket is not suitable for mounting in damp environments or outdoors. Sentrysocket, incorporating an RCD, is part of a complete range of fixed and portable wiring devices and circuit protection devices suitable for use in domestic, commercial and industrial applications. Active control circuits Incorporate a Re-set mechanism and are mains failure sensitive, ie they will function under all the normal conditions expected of an RCD, but will also trip in the event of a power cut or a sudden, dramatic reduction in mains voltage. This makes them ideal for use where it would be hazardous for equipment to suddenly energise after return of mains power, such as use with rotating machinery and heat developing apparatus. Passive control circuits Incorporate a Stay-set mechanism and is mains failure proof, ie it will function under all the normal conditions expected of an RCD and will not trip in the event of a power cut. This makes it suitable for use with freezers or in inaccessible or unmanned locations. Features Suitable for most residential, commercial and light industrial applications Active and passive control circuit applications Comply fully with current Wiring Regulations Double pole switching Flexible and versatile in use Ideal for use with equipment subject to wet weather or high humidity Part of a complete range of MK circuit protection devices They are a.c. and pulsating DC sensitive for residual current Installation ogic Plus RCD protected switch socket outlets can be wall or bench mounted. Do not mount or use as a trailing socket or where they may be subject to excessive moisture or dampness. Dimensions (mm) Single socket Double socket 6 6 6. 6. Flush mounting steel wall box It should be noted that some of the conduit entries may be restricted, depending upon their positions and the depth of box used. sentrysocket T test before use press button - T off (tripped) on active control device trips with loss of mains 0mA tripping current sentrysocket T R Cable management Sentrysockets can be mounted in a variety of MK trunking systems. 0.6 0.6 9
6 ogic Plus Technical wiring devices white www.mkelectric.co.uk Sentrysocket Installation Flush mounting steel wall box It should be noted that some of the conduit entries may be restricted, depending upon their positions and the depth of box used. Socket Testing: Single Socket Testing After installation, turn the mains electricity supply on. To test that the Sentrysocket is functioning correctly:. Ensure that no appliance is connected to the Sentrysocket. Switch Sentrysocket on: The switch should remain closed and the red flag will appear in the window. If the switch fails to remain closed, check that the Supply and connections are not reversed or the Supply connection is not open circuit. If the Sentrysocket is correctly connected and still trips after being switched on, the Sentrysocket is faulty and should not be used. If the Sentrysocket stays on, press the test button: The switch will open and the white flag will appear In the window. If the Sentrysocket does not trip and there is mains voltage present at the socket outlet, Sentrysocket is faulty and should not be used.. Switch Sentrysocket on: Connect an RCD tester and ensure that the Sentrysocket trips within the specified time: 00 ms AT RATED TRIP CURRET 0 ms AT x RATED TRIP CURRET If the Sentrysocket does not trip within the specified times then the product is faulty and should not be used (If more than one RCD is in series then there is no guarantee as to which device will trip first).. Reset all tripped RCD s including the Sentrysocket.. Switch off the mains supply switch disconnector. On mains failure, a Sentrysocket with Active Control Circuit will trip, whilst a Sentrysocket with Passive Control Circuit will not trip. If the Active Control device does not trip, it is faulty and should not be used see note below. If no faults have been found then installation testing has been completed successfully. ote: If a fault is identified at any stage of installation testing procedure do not use Sentrysocket, and contact your local electrician, or your local MK stockist. Double Socket Testing After installation, turn the mains electricity supply on. To test that the Sentrysocket is functioning correctly follow the steps to below:. Ensure that no appliance is connected to the Sentrysocket.. Reset Press the button marked R (for Reset) the contact status indicator should show red, indicating that the socket outlets are now live (if the switches are in the O positions).. Test Press the TEST button marked T (for Test), the product should trip with the contact status indicator showing black. In this state the socket outlets are disconnected from the supply.. Reset Press the button marked R again, the contact status indicator should show red.. Connect an RCD Tester to either socket outlet and ensure that the Sentrysocket trips with the specified times below: 00 ms AT RATED TRIP CURRET 0 ms AT x RATED TRIP CURRET 6. Reset the Sentrysocket as in step above. 7. Switch off the Mains Supply Switch Disconnector. 8. A Sentrysocket with Active Control Circuit should trip while a Sentrysocket with Passive Control Circuit should not trip. If all the operations in steps to 8 above give correct results, the Sentrysocket RCD socket outlet is safe to use. If the procedures in steps to 8 above are not completed correctly, do not use the Sentrysocket product and seek professional advice or contact the MK Technical Sales and Service department on + (0)68 670.
ogic Plus Technical 7 technical hotline + (0)68 670 white wiring devices Filtered Switchsocket Outlets ogic Plus Filtered Switch Socket Outlets comply with BS 7: 00. Current rating: A maximum total for sockets Voltage rating: 0V a.c. 0Hz Earth leakage: 0. ma Suppression: 0 khz 0 MHz (transients) Maximum energy absorption: 0 Joules 0 Joules E Terminal capacity: K and K, x 6mm x mm, x.mm, x.mm Operating temperature: C to +0 C (not to exceed an average of more than C in any hour period) Thermal overload: The K filter socket incorporates a thermal overload device in the RFI filter section. Overload current causes temperature rise, resulting in automatic trip out. The overload device will re-set as the temperature falls. A range of sockets in the ogic Plus style, designed to combat interference to or data losses on sensitive electrical products and systems due to mains borne voltage spikes and RFI. Such systems include: Computer or microprocessor based equipment Telecommunications systems Electronic measurement equipment Cash registers Audio visual and hi-fi equipment These products can be quickly installed as replacements for existing twin amp sockets or in a new installation. Two earth terminals on each product provide a double earth facility for use when installations require a high integrity protective connection as specified within BS 767: 008. Filter cassettes Filter cassettes are supplied with sockets and have an ED which shows green under normal conditions but will turn red or extinguish when a replacement cassette (K800) is required. An alarm will also beep at second intervals to indicate replacement necessity. It can be de-activated if required. IPXD Max. installation altitude: 000 metres Cable management ogic Plus socket outlets can be mounted in a variety of MK trunking systems. Dimensions (mm) 6 0 Features Moulded on indicator flash on switches will not rub off totally safe pin operated safety shutter Printed terminal markings on grey rear mouldings for clearer identification Reduces risk of damage to equipment and down time Reduces risk of data loss way filtering into appliance and back into mains supply Double pole switches Dual earth terminals for high integrity earthing Clearly visible ED on filter cassette, changes from green to red when replacement required Simple replacement of cassettes 0 year guarantee (except filter cassette) mm minimum switch contact gap Backed out and captive terminal screws 0.6 7
8 ogic Plus Technical wiring devices white www.mkelectric.co.uk Filtered Switchsocket Outlets Product features Audible warning Ensure that the connecting pins protruding from the connector bottom of the replacement Filter Replacement Cassette are not damaged or bent before installation. If in doubt, contact filter cassette MK Technical Sales Service Department on + (0)68 670. ocking screw. The MK Filtered Switchsocket, in common with many other filters uses Voltage Dependant Resistors for spike suppression purposes. The performance of these devices will eventually degrade with use to a level where they will no longer provide adequate protection. When this occurs the spike filer performance of the MK Filtered Switchsocket outlet can be restored by replacing the filter cassette. When the filter cassette needs replacing, the green indicator on the Replacement Filer Cassette will glow red or go out, an audible beep every five seconds may also be heard. ote: As with all filters, these Filter Sockets will reduce the magnitude of RFI and spikes and consequently their ability to interfere with connected equipment. They will not completely remove the interference from the supply. Figure Filter indicator Replacement Audible warning filter connector cassette Filter indicator Audible warning connector Filter indicator Figure. Fit the new filter cassette by carefully sliding it into the aperture and gently pushing it down while turning the screw clockwise until the filter cassette is flush with the surface. Do not turn the screw any further as this will cause distortion of the plastic mouldings. Product and packaging can safely be disposed of via standard refuse facilities at the end of its useful life. Figure a ocking screw Installation Replaceable Spike Filter Cassette ote: To ensure a safe installation; this product should be installed by a competent person. it is important that all connections are made as instructed.. The filter cassette can be removed and replaced without switching off the mains or removing any plugs from the filter socket.. Remove the filter cassette by turning the jacking screw anti-clockwise to partially eject it (see Figure ), and then gently pulling the cassette upwards, (see Figure a).. Only fit the MK Replacement Filter Cassette (K800WHI). Unpack the new filer cassette and check that the pins along the bottom edge are not bent or broken. If these pins are damaged, do not fit the replacement cassette. The audible sound indicating that the filter cassette needs replacing, is optional. It may be prevented by removing the small connector on the two end pins, (see Figure b), before fitting it into the socket. Figure b Audible warning connector
ogic Plus Technical 9 technical hotline + (0)68 670 white wiring devices Round Pin Socket Outlets Round pin socket outlets comply with BS 6: 90. Voltage rating: 0V a.c. Terminal capacities: amp sockets (K770): 7 x mm x.mm x.mm x mm amp sockets (K77, K89): x.mm x mm x 6mm (stranded) amp sockets (K77, K89, K9): x.mm x mm x 6mm (stranded) Ambient operating temperature: C to +0 C (not to exceed an average of more than C in any hour period) IPXD Max. installation altitude: 000 metres A range of round pin socket outlets designed for ease of installation and having all the advantages and design features of the round pin ogic Plus range. These products can be quickly installed as replace ments for existing socket outlets or in new installations. Features Top access terminals make wiring easier and quicker Integral O indicator on switches will not rub off totally safe Optional neon indicator on A switched socket rockers with 7 visibility in the horizontal and vertical planes mm minimum switch contact gap Double pole switching Terminal screws backed out Additional electrical safety from neutral make first, break last feature on switched sockets Switch contacts with silver contact points on both surfaces for good continuity A and A sockets contain a pin operated safety shutter Printed terminal markings on grey rear mouldings for clearer identification A socket shuttered Installation ogic Plus socket outlets can be wall or bench mounted do not mount or use as a trailing socket or where they may be subjected to excessive moisture or dampness. Dimensions (mm) Cable management ogic Plus socket outlets can be mounted in a variety of MK trunking systems. 60. Depth Amp sockets: mm Amp sockets: mm Amp sockets: mm BOX TYPES Flush for extra Flush wiring space Surface Insulated Surface Metal A and A ZIC 6ZIC K0WHI KAM KAM A 99ZIC ZIC K0WHI KAM 6ZIC KAM
0 ogic Plus Technical wiring devices white www.mkelectric.co.uk on UK Socket Outlets A American sockets comply with SASO 0: 00 A AMERICA 6A P+E German sockets comply with IEC 6088-: 006 A American Socket 6 9 Voltage rating: 7V a.c. Current rating: A Terminal capacity: ive, neutral & earth x.mm x mm x 6mm (stranded) Max. installation altitude: 000 metres 6A P+E German Socket Voltage rating: 0V a.c. Current rating: 6A Terminal capacity: ive, neutral & earth x.mm x.mm x mm BOX TYPES 60. Flush Flush (for extra Surface wiring space) 0.6 gang ZIC 6ZIC K0WHI gang ZIC 8ZIC KWHI 6A P+E GERMA BOX TYPES All dimensions in mm Flush Surface gang 6 ZIC K0 WHI gang 8 ZIC K7 WHI Ambient operating temperature: C to +0 C (not to exceed an average of more than C in any hour period) IPXD 6 9 ote: 6A P+E German Outlet: These products are OT suitable for mm deep boxes. Max. installation altitude: 000 metres 60. 0.6 0 All dimensions in mm
ogic Plus Technical technical hotline + (0)68 670 white wiring devices Three Pole Fan Isolators Comply with BS E 6097: 99 Voltage rating: 0V a.c. 0Hz Current rating: 0 amps Terminal capacity: x mm x.mm x.mm x mm x 6mm Contact gap: mm switch contact gap Classifications Method of operation: Stored energy operation Suitability for isolation: Suitable for isolation Ratings Utilisation category ACB Rated operational voltage (Ue) 0V Conventional free air thermal current (Ith) 0A Rated frequency 0Hz Rated making capacity 00A rms Rated breaking capacity 80A rms Rated conditional short-circuit current 6000A rms (with supply side protective device GEC IT 6 BS88: part : 988 6A 0VAC utilisation category gg 80KA breaking capacity fuse links.) Operating temperature: C to +0 C The MK Three Pole Fan Isolator provides a safe and simple method of isolating mechanical fan units and is particularly useful in bathrooms, toilets, storerooms and basements where there is little or no natural light. For example, timer controlled fans are often linked into the lighting circuit for energy saving and convenience. In such an installation there is often a need for the lighting circuit to remain live to provide light whilst the fan unit is externally isolated so that routine maintenance and repairs can be carried out in complete safety. The fan isolator can be used as a double pole or triple pole isolator. In addition it includes a clear on/off indicator and the frontplate features a fan isolator symbol for easy circuit identification. Dimensions (mm) on off isolator 9 60. BOX TYPES Flush 99ZIC Surface K60WHI IPX Max. installation altitude: 000 metres Features Switchlock list no. K88 is available to allow the isolator to be locked in the disconnected position to facilitate fan maintenance
ogic Plus Technical wiring devices white www.mkelectric.co.uk Three Pole Fan Isolators Wiring diagrams Two pole switching for fan units without timers Supply TOP Rear view of Fan Isolator To Fan Unit without Timer (see Fan Unit Intructions) (switched) Supply TOP Rear view of Fan Isolator To Fan Unit without Timer (see Fan Unit Intructions) (switched) Three pole switching for fan units incorporating timers Supply TOP Rear view of Fan Isolator To Fan Unit with Timer (see Fan Unit Intructions) (unswitched) (switched) Supply TOP Rear view of Fan Isolator To Fan Unit with Timer (see Fan Unit Intructions) (unswitched) (switched)
ogic Plus Technical technical hotline + (0)68 670 white wiring devices Shaver Socket Outlets Shaver socket outlets comply with BS 7: 970 and IEC 88-: 99. Plug pin apertures, and engagement face dimensions comply with BS 7: 970. Voltage rating: 00-0V a.c. Input Maximum load: 00 ma (internal thermister trip current) Terminal capacities: Each terminal will accommodate x mm, or x.mm, x. solid conductors Ambient operating temperature: C to +0 C IPXD Max. installation altitude: 000 metres Designed for ease of installation and having many of the advantageous features of the ogic Plus range. The shaver socket outlet accommodates the following plugs: British mm dia pins on 6.6mm pitch (0V socket) to BS 7: 970. European mm dia pins on 7 to 9mm pitch (0V socket) to IEC 8: 97 Standard C. Australian 6. x.6 flat blades each set at 0 to the vertical on a nominal pitch of.7mm (0V socket) AS C: 96. The fuse carrier is captive and opened by a fast acting, screwdriver operated worm drive screw for ease of replacement. Installation Shaver socket outlets may be wall or bench mounted. This shaver socket must not be used in bathrooms and washrooms. on-isolated, fused, shaver socket outlets must never be installed in any location subject to splashes, condensation or damp conditions. For installation in any other room where a wash basin or shower cubicle is installed then refer to the current IEE wiring regulations. Cable management Features Top access terminals make wiring quicker and easier Only one size of screwdriver required for installation Terminal screws supplied backed out and held captive within the terminal moulding Dimensions (mm) 9 Printed terminal markings on grey rear mouldings for clearer identification Front plate fixing screws retained on rear case moulding ogic Plus socket outlets can be mounted in a variety of MK trunking systems. shavers only 00-0V ac fuse 60. 0
ogic Plus Technical wiring devices white www.mkelectric.co.uk Shaver/Toothbrush Supply Units Shaver/Toothbrush supply units comply with BS 68--: 998 Accommodates plugs as follows: British mm dia pins on 6.6mm pitch (0V socket) to BS 7: 970. European mm dia pins on 7 to 9mm pitch (0V socket) to IEC 8: 97 Standard C. Australian 6. x.6 flat blades each set at 0 to the vertical on a nominal pitch of.7mm (0V socket) AS C: 96. American 6.6 x.6 flat horizontal blades on.7mm pitch (V socket) to ASI C7.0. ote: K706WHI is a on UK Shaver/Toothbrush Supply Unit Voltage rating: K70: 0V a.c. Input (will operate at 0-0V a.c.) K706: 7V a.c. Input (will operate at 0-0V a.c.) 0V or V nominal outputs Designed for ease of installation and having many of the advantageous design features of the ogic Plus range. May be used in bathrooms and washrooms must only be installed in accordance with BS 767: 008. Current rating: K70: 00mA max. (internal thermister trip current) K706: 00mA max. (internal thermister trip current) Maximum load: 0VA o load voltage < 7V Terminal capacities: Each terminal will accommodate x mm or x.mm solid conductors* Ambient operating temperature: C to +0 C IP (In Zone if fixed where direct spray from showers is unlikely) Max. installation altitude: 000 metres *The design of this unit means that on no load the transformer output is allowed to be as high as 7V. This means that rechargeable shavers and toothbrushes intended for use on the continent may be damaged by the inrush current created by this higher voltage. Rechargeable shavers and toothbrushes with a wide range of input voltage should be recharged at V. Shavers and toothbrushes manufactured for the UK are designed to be used with a transformer unit. oads in excess of 0VA may cause the solid state overload to operate before shaving is completed. This is to protect the transformer. Features Bottom access terminal screws make wiring quicker and easier Automatic primary supply switching on insertion of plug Choice of 0V or V output socket positions Safety interlocked shutters to prevent insertion of two plugs simultaneously Only one size of screwdriver required for installation Installation Shaver/Toothbrush supply unit should be wall mounted. Wiring An installation instruction leaflet is available. ist no. 99 P. Terminal screws supplied backed out and held captive within the terminal moulding Printed terminal markings on grey rear mouldings for clearer identification Front plate fixing screws retained on rear case moulding Integral over current device to protect transformer Suitable for use with electric toothbrush chargers Dimensions (mm) 6 V 0V 9
ogic Plus Technical technical hotline + (0)68 670 white wiring devices Connection Units, 0A Switches and Flex Outlets All ogic Plus Connection Units comply with BS 6: Part : 99. The 0A DP switch complies with BS E 60669-: 999 The flex outlet plate complies with BS 7: 00. Fuses are to BS 6. Voltage rating: 0V a.c. Current rating: Connection units amp DP switches 0 amp Flex outlets 0 amp Terminal capacity: Supply terminal: oad terminals: Flex outlet/ Cord grip capacity: Connection units: Installation ogic Plus connection units and 0A cable outlets and 0A switches can be wall or bench mounted. Do not use on a trailing lead. Cable Management x 6mm stranded x mm x.mm x 6mm stranded x mm x.mm min: core, 0.mm max: core,.mm 0 amp DP switches & flex outlet plate min: core,.mm max: core,.mm Ambient operating temperature: C to +0 C (not to exceed an average of more than C in any hour period) With flex outlet: IPXD Without flex outlet: IPX Max. installation altitude: 000 metres ogic Plus connection units and DP switches can be mounted in a variety of MK trunking systems. A range of A fused Connection Units and 0A DP switches designed for the connection of refrigerators, water heaters, central heating boilers and other fixed appliances. The ranges are designed for ease of instal la tion and have the advantageous design features of the ogic Plus range. eon indicators eon indicators can be included in the rockers of the switched connection units. In the case of unswitched units, they are located centrally and uppermost on the front plate. eon indicators are integrally wired into the product and do not require separate connection when installing. The design gives 7 visibility in the horizon tal and vertical planes. Fuse carriers These are captive and are opened by a fast acting, screwdriver operated worm drive for ease of replacement. A tamper-proof version is also available. Fuse carriers can be locked open using a padlock, ist o. K000. Flex outlets Bottom outlet types are supplied with blanking plug allowing use where the bottom outlet is not required. Spare blanking plugs are available. The products are equipped with very strong, push-fit nylon cord grips making installation safe, quick and easy. Flex outlet plate An unfused flex outlet with cord grip plate and pairs of terminals. Installation Wiring Products must be installed in accordance with current IEE Regulations. Changing Fuses. Unscrew the fuse carrier screw to partially eject the carrier.. Carefully lever the carrier out further to remove the fuse. ote: The carrier does not come fully out.. Always replace with a BS 6 type fuse (as used in A plugs) of the correct rating.. Consistent fuse blowing could mean a faulty appliance. If in doubt, consult a qualified electrician.. Push carrier back until engaging with jacking screw. Screw the carrier down until flush with surface of the plate. Do not over tighten the screw.
6 ogic Plus Technical wiring devices white www.mkelectric.co.uk Connection Units, 0A Switches and Flex Outlets Features Optional indicators in the switch rockers with 7 visibility in the horizontal and vertical planes Worm-drive operated fuse carriers for additional security (tamper-proof version available) Fuse carrier lockable in open position All supply and load cables can be cut and stripped to the same length Integrally wired indicators save installation time Push-fit cord grips, for safer, quicker installation Angled, top mounted terminal screws simplify wiring Moulded on indicator flash on switches cannot rub off totally safe Captive fuse carrier Additional electrical safety from neutral make first, break last feature Secure cable and flexible cord connection All terminal and fixing screws operated by one-size (mm) screwdriver Backed out and captive terminal screws Supply and load cable cords cut and stripped to same length Bottom outlet and cord grip Blanking plug for bottom outlet ote: These switches are not recommended for switching large banks of PCs Dimensions (mm) 9 Products with front flex outlet Front outlet cord grip ockable fuse carrier fuse dia 60. 9 Products with flex outlet in base and thick frontplate K090WHI Supply and non flexible load cables fuse 60. PEASE OTE THAT THE TERMIA AYOUT OF THE FEX OUTET, K090, IS DIFFERET TO THE OTHER SHOW ABOVE.
ogic Plus Technical 7 technical hotline + (0)68 670 white wiring devices 0A ockable Fire Alarm Isolator Switch Voltage rating: 0V a.c. Current rating: 0 amp Terminal capacity: The isolators comply with BS 60669--: 00 The Isolator is intended for use with building Alarm Systems that are required to comply with BS 89 Part. BS 89 Part states; Clause.c To facilitate local isolation during maintenance, suitable means should be provided for double pole isolation of the low voltage supply circuit that serves the power supply and control equipment. Clause 9.e. Means should be provided for double pole isolation of the mains supply to all parts of the system; the isolation facilities should be suitably sited, in the vicinity of the equipment served, for use by maintenance technicians without the need for access to remote parts of the building. It should be possible to lock the facilities in both the normal and isolate positions to prevent unauthorized use. Features The built in lock ensures power cannot be provided without the key being operated, making it safe to carry out maintenance to Fire Alarms Printed terminal markings on grey rear of the switch moulding for clearer identification Double Pole switching ive, eutral & Earth x.mm x mm x 6mm Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) With flex outlet: IPXD Without flex outlet: IPX Max. installation altitude: 000 metres IPXD Max. Installation altitude 000 metres ote: The lock fitted to these isolators is universal for all MK 0A Isolators in the range. However, the keys are different to those used on all other MK Key Operated Switched Products, for added security. Only one size of screwdriver required for installation
8 ogic Plus Technical wiring devices white www.mkelectric.co.uk High Current Switches and Cooker Control Units All DP switches in the range conform to BS E 60669-: 999 All Cooker Control Units in the range conform to BS 77: 99 Cooker Connection Unit conforms to BS 7: 00 Voltage rating: 0V a.c. Current: A Switch A Cooker Control Unit A Cooker Connection Unit 0A Switch (Resistive oad) Switch: mm contact gap Double pole operation except socket switch on Cooker Control Unit Terminal capacity, 0A switches, Cooker Control Unit and Cooker Connection Unit: x mm x 6mm x 6mm Terminal capacity, A Switch: x.mm x mm x 6mm Ambient operating temperature: C to +0 C (not to exceed an average of more than C in any hour period) IPXD (K06, K060, K0, K00, K00, K0, K0) IPX (K0, K0, KCK, KSH, K0) Max. installation altitude: 000 metres Features Positive switch action Positive double pole switching Toggle action switches Metal front plates available Replaceable neon indicators Wide product choice ote: These switches are not recommended for switching large banks of PCs A range of switches and cooker control units harmonising with the ogic Plus style, suitable for the switching of all domestic, commercial and industrial appliances where higher current ratings are required, i.e. cookers, heaters etc. Metal units are particularly suitable for refurbishment projects. BOX DEPTHS ist o. Max. Cable Size Flush Surface Switches K0WHI 6mm mm 0mm 0mm 6mm 0mm K0WHI 6mm mm 0mm 0mm 6mm 0mm KWHI 6mm mm 0mm 0mm 7mm 0mm K0WHI 0mm Supplied with box K0WHI 0mm mm Cooker control units K00WHI 0mm Supplied with box K0WHI 0mm Supplied with box K060WHI 6mm mm 0mm 7mm K06WHI 6mm mm 0mm 7mm K00WHI 0mm Supplied with box K0WHI 0mm mm BOX REFERECES Flush Surface Box depth gang gang gang gang 0 K0WHI 8ZIC 8ZIC 0 K0WHI K7WHI 6 877ZIC 7 878ZIC 0AM (Cooker)
ogic Plus Technical 9 technical hotline + (0)68 670 white wiring devices High Current Switches and Cooker Control Units Dimensions (mm) 6 off off off on on on cooker socket 60. K0 0.6 K06 or K060 (without pilot lights) 9 6 7 off 6 0.6 off on cooker off on socket 89 on 0.6 K or K0 without pilot light KCK printed cooker KSH printed shower 87 9 K0 or K00 (without pilot lights) 60 off 8 0.6 on 6 off on cooker off on socket 0 K0 K00 66 9 66 9 79 off on cooker off on socket 0 79 off on K0 K0
0 ogic Plus Technical wiring devices white www.mkelectric.co.uk Plateswitches All ogic Plus plateswitches comply with BS E 60669-: 999 Voltage rating: 0V a.c. 0Hz Current rating: 0 amps no derating when used on fluorescent or inductive loads 0 amps no derating when used on fluorescent or inductive loads Terminal capacity: All products except K870/7/7 x mm x.mm x.mm x mm x 6mm For products K870/7/7 x mm x.mm x.mm x mm Contact gap: mm switch contact gap Operating temperature: C to +0 C IPXD Max. installation altitude: 000 metres Operational testing (all plateswitches): tested to 00,000 operations for mechanical life tested to 0,000 operations at 0 amp rating tested to 0,000 operations at 0 amp rating ogic Plus plateswitches are designed to blend in with the decor, whilst complemen ting a wide range of other ogic Plus accessories. They are designed for easy instal lation in plaster depth boxes and are suitable for controlling lighting circuits in domestic, commercial and industrial applications. eon locator A textured, polycarbonate moulding allowing the glow of the neon to be seen at almost any angle. Designed to complement the ogic Plus,, or gang plateswitches. It is easy to install in existing locations. For gang applications using a mm deep box simplifies wiring. Features Two way switches can be wired as one or two way All products clearly printed with BS os., ratings, etc Matching Grid switches available in0 or 0A ratings mm switch contact gap Positive switch action Cable Management ogic Plus plateswitches can be mounted in a variety of MK trunking systems. Top access, backed out and captive terminal screws (except ogic Plus list numbers K870, K87 and K87) eon locator available making switch easy to find in darkened rooms
ogic Plus Technical technical hotline + (0)68 670 white wiring devices Plateswitches 8 8 8 8 Dimensions (mm) gang gang gang 8 60. 8 8 8 60. 8 0.6 8 60. 8 60. 8 60. 8 Two-way switching Two-way switching Two-way switching 8Two-way One-way wire control switching 60. gang 6 gang Two-way switching 6 6 Two-way wire control switching plus Two-way wire control switching intermediate switching Two-way switching wire control gang architrave 60. 6 8 gang architrave 0.6 One-way switching Two-way One-way switching One-way switching One-way switching 0.6 Two-way plus intermediate Two-way plus Two-way switching intermediate plus switching switching intermediate Two-way wire control plusswitching intermediate wire control switching Two-way plus Two-way plus intermediate Two-way plusswitching intermediate switching Two-way intermediate wire control plus switching wire control intermediate switching Sectional drawings show the furthest projections from wire the control back of the frontplate (wall surface). Two-way plus intermediate switching wire control Wiring Diagrams One-way switching amp/s amp/s Two-way switching amp/s wire control amp/s amp/s amp/s Dotted lines show alternative switch positions amp/s SW. SW. SW. SW. amp/s amp/s Dotted lines show amp/s alternative switch positions Two-way switches Two-way switches Two-way switches Two-way switches Two-way switches Two-way Two-way switches switch Two-way switch Two-way switch Dotted lines show alternative switch positions Dotted lines show alternative switch positions amp/s amp/s Two-way Dotted switching lines show alternative plus switch intermediate positions switching wire control Two-way switching wire control amp/s Two-way Intermediate switch switch Two-way Intermediate switch switch Two-way switches Two-way Intermediate switch switch Two-way Intermediate switch switch amp/s SW. amp/s SW. Dotted lines show alternative switch positions amp/s Dotted lines show alternative switch positions amp/s Dotted lines show alternative switch positions Dotted lines show alternative switch positions amp/s Dotted lines show alternative switch positions SW. amp/s Two-way switches Two-way switches Intermediate switch Intermediate switch Dotted lines show alternative switch positions Dotted lines show alternative switch positions Dotted lines show alternative switch positions Two-way switch Intermediate switch amp/s Dotted lines show alternative switch positions amp/s Dotted lines show alternative switch positions amp/s SW. Dotted lines show Dotted alternative lines show switch alternative positionswitch positions amp/s Two-way switches Dotted lines show alternative switch positions Intermediate switch Two-way switch Two-way switch Two-way switch Two-way switch Two-way switch Two-way switch Two-way switch Two-way switching plus intermediate switching wire control amp/s SW. Two-way switch Intermediate switch Dotted lines show alternative switch positions Two-way switch.b. Terminal positions may alter. The above diagrams are to show wiring layout. Two-way switch
ogic Plus Technical wiring devices white www.mkelectric.co.uk Dimmer Switches All CE marked ogic Plus dimmer switches comply with the EC ow Voltage Directive: 7//EEC, Electromagnetic Compatibility Directive 89/6/EEC They also comply with BS E 60669-- and BS E 0 *on-uk dimmer switches see note below Mains Supply Voltage: 0V a.c. (ominal) 0V a.c. (ominal, on-uk) Mains Supply Voltage Range: 6V a.c. to V a.c. 00V a.c. to 0V a.c Mains Supply Frequency: 0Hz ±Hz 60Hz ±Hz Type of oads: Standard Dimmers: Fused GS Tungsten Filament lamps only to BS E6006: 996 and BS E60-: 000, rated at 0/0V Intelligent Dimmers: Fused GS Tungsten Filament lamps to BS E6006: 996 and BS E60-, rated at 0/0V. Dimmable wire wound or electronic ow Voltage Transformers of good quality. Can also be used with good quality mains voltage halogen lamps incorporating GU0 bases. Please check with lamp manufacturer to determine suitability. ote: Transformer must be suitable for dimming using phase delay (leading edge) and OT only phase cut (trailing edge) type of dimmers. Warning: Standard and Intelligent dimmer switches are not suitable for use with Fluorescent amps or Energy Saving amps. CF lamp dimmers: Dimmable compact fluorescent lamps rated at 0/0V. Operating temperature: 0 C to +0 C IPXD Max. installation altitude: 000 metres MK dimmer switches can fall into one of four categories: ) Standard Dimmer Switches ) Intelligent Dimmer Switches ) on-uk Dimmer Switches ) CF lamp dimmer switches Standard Dimmer Switches Dimmer Switches belonging to this category employ simpler electronic circuitry and the CE marked products make use of thermal switches to conform to the very stringent requirements of the Standard BS E 60669--, for overload protection. They are only suitable for use with normal tungsten filament lamps with internal fuses, conforming to BS E 6006: 996 and BS E 60- Standards and do not have any added features, e.g. soft start, ability to control dimmable transformers for low voltage, etc. Standard Dimmer Switches are not suitable for use with transformers for ow Voltage ighting or Fluorescent oads, including Energy Saving amps. Intelligent Dimmer Switches Dimmer Switches belonging to this category, employ the latest, state of the art, micro-controller based electronic circuitry and use current sensing to compute the load conditions. These products show progressive reaction to overload conditions, depending on the extent of overload as shown in the table below. ist numbers belonging to this category are identified by the suffix letters V, e.g. K0 WHI V. All MK Intelligent Dimmer Switches employ one pole change over switches to facilitate two way switching. MK Intelligent Dimmer Switches are not suitable for use with Fluorescent oads, including Energy Saving amps. *on-uk Dimmer Switches Dimmer switches belonging to this category only conform to the relevant parts of BS E 66069--, without conforming to BS E 0. oads suitable for use with standard dimmer switches above are also suitable for use with this category of dimmer switch. CF amp dimmer switches Dimmer switches belonging to this category employ the latest, state of the art, micro-controller based electronic circuitry used in other intelligent dimmer switches. In addition they utilise control software to improve performance and life of dimmable compact fluorescent lamps. Only one Dimmer Switch can be used in a two-way switching circuit.
ogic Plus Technical technical hotline + (0)68 670 white wiring devices Dimmer Switches Features Intelligent Dimmer Switches incorporate the following advanced features Suitable for dimming ow Voltage Halogen lamps via good quality, fully dimmable electronic or wire-wound transformers Can be used with good quality mains voltage halogen lamps incorporating GU0 bases. Please check with lamp manufacturer to determine suitability oad current sensing: These dimmers continuously monitor the load current to help protect against overheating in wire wound transformers and to prevent overloading of the dimmer for long term reliability. Soft Start, which gradually increases the light output from the load over to seconds after switch on. The Soft Start feature is also particularly beneficial when used to dim Mains Voltage Tungsten Halogen lamps which inherently have a very high inrush current at switch on Standard Dimmer Switches Suitable only for use with fused GS Tungsten Filament lamps to BS E 6006 and BS E 60- One way dimmer switches incorporate manual soft start Incorporate thermal switches for protection against overload Dimensions (mm) 8 9 6 60. CF amp dimmer switches Suitable only for use with compact fluorescent lamps designed specifically for dimming. oad current sensing: These dimmers continuously monitor the load current to help prevent overloading of the dimmer for long term reliability. Full brightness start to increase lamp life, the dimmer will reduce the light level to the level set within - seconds. Total connected load must not be less than the minimum power load rating of W. A maximum of lamps only must be connected to each dimmer switch. 60-00W CIRCUIT 0-00W CIRCUIT COMMETS Overload management: Overload management: 60-00W nominal 0-00W nominal 60-6W function without dimming 0-7W function without dimming > 6-70W dim to 68V±8V r.m.s. > 7-00W dim to 68V±8V r.m.s. This is the min. > 70W switch off > 00W switch off controlled voltage ITEIGET DIMMER SWITCHES Rating gang single 0-00W (V and mains voltage dimmer halogen rating 0-0W/VA) gang double x 0-00W (V and mains voltage per dimmer dimmer halogen rating x 0-0W/VA) gang single 60-00W (V and mains voltage dimmer halogen 60-00W/VA) Max o. of Transformers (total rating of all transformers must not exceed maximum VA rating of dimmer) One-way switching Supply 0V a.c. - 0Hz Two-way switching (only one dimmer can be used) Supply 0V a.c. - 0Hz oad oad way switch C C C DIMMER DIMMER Wires must be connected to the correct dimmer terminals. DO OT connect earth to dimmer. Please Fluorescent note the dimmer dimmer may be substituted for any of the Two-Way switches shown on page. HF Fluorescent Ballast + -0V DIMMIG COTROER Wires must be connected to the correct dimmer terminals. DO OT connect earth to dimmer.
ogic Plus Technical wiring devices white www.mkelectric.co.uk Euro and JU6C Data Frontplates BS 7: 00 Dimensions Height: Width: 8.7mm 8.7mm (G) 7mm (G) Depth: 9mm Aperture Dimensions (nominal) Frontplates used for mounting snapfit data modules. Euro Frontplates Height: Width: 0mm 0mm (G) 00mm (G) Dimensions (mm) JU6C Frontplates Height: Width: Features 7mm mm G, G and G Euro Frontplates G JU6C Frontplate ogic Plus style Colour matched to MK ogic Plus range Accept industry standard Euro or JU6C snapfit modules G Euro frontplates accept or Euro modules, (x0mm or 0x0mm aperture) G Euro frontplate accepts Euro modules, (00 x 0mm aperture) G JU6C frontplate accepts two JU6C modules (7 x 7mm aperture) module (. x 0mm) blank available for Euro frontplates Euro Frontplates Gang & module Gang module 9 60. K8WHI/K8WHI 7 9 0.6 K8WHI JU6C Frontplates Gang 6 module 9 60. K7WHI 06 9 80.9 K8WHI
ogic Plus Technical technical hotline + (0)68 670 white wiring devices Power Modules K80: BS 6 Part : 99 K8: IEC 6088-: 006 K8: SASO 0: 00 K8: BS 6: 90 K8: French ational Standard F C 6- A range of euro modules designed to provide a variety of power options. A UK A UK 6A German 6A French/Belgian A American A USB Charging Module Voltage rating: 0V a.c. Current rating: A Terminal capacity: ive, neutral & earth x.mm x mm x 6mm (stranded) Voltage rating: 0V a.c. Current rating: A Terminal capacity: ive, neutral & earth x.mm x mm x 6mm (stranded) Voltage rating: 0V a.c. Current rating: 6A Terminal capacity: ive, neutral & earth x.mm x.mm x mm Voltage rating: 0V a.c. Current rating: 6A Terminal capacity: ive, neutral & earth x.mm x mm x 6mm Voltage rating: 7V a.c. Current rating: A Terminal capacity: ive, neutral & earth x.mm x mm x 6mm (stranded) Input Voltage rating: 0-0V a.c. Frequency : 0Hz Rated Current: 0.6A Terminal Capacity: ive & neutral x.mm Output Voltage rating: x V d.c. Max current: A per socket Charging sockets: USB.0 type A Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) Ambient operating temperature: 0 C to +0 C IPXD IPXD IPXD IPXD IPXD IPXD Max. installation altitude: 000 metres Max. installation altitude: 000 metres Max. installation altitude: 000 metres Max. installation altitude: 000 metres Max. installation altitude: 000 metres Max. installation altitude: 000 metres Dimensions (mm) A UK 0 A UK 0 6A German 0 6A French/ Belgian 0 A American 0 A USB Charging Module 0 0 0 0 0 0 0 9 0 9 K80 K8 K8 K8 K8 K87 BOX TYPES Minimum BOX TYPES Minimum BOX TYPES Minimum BOX TYPES Minimum BOX TYPES Minimum MK EURO FROT PATE THICKESS BOX TYPES mm mm 6mm 6mm mm > 7mm Min mm Extra wiring space Extra wiring space Extra wiring space < 7mm Min 6mm 6mm 6mm 6mm
6 ogic Plus Technical wiring devices white www.mkelectric.co.uk RJ Data Outlets ISO/IEC 80 E 07 TIA 68 E 00 Installation Maximum cable length 90m. Suitable for use in all JU6C, Euro and MK Modular frontplates, available in the ogic Plus range, Cat e and Cat 6 modules suitable for use in structured cabling distribution systems. Cable bend radii, 0mm during TIA WIRIG SCHEME COOUR CODES: installation, 0mm after installation. E F Pin o. 68A G 68B H P P Maximum pull force 8.7kg. WHITE / green WHITE / orange P P P P P Do P not over tighten cable ties. GREE / white ORAGE / white Do not unwind the twists in the wire pairs by more than mm max. WHITE / orange WHITE/ green D E F G H BUE / white BUE / white 68A 68B WHITE / blue WHITE / blue Euro and JU6C modules are to be wired as follows 8 7 6 F G H RJ Cat.e Euro K8 Installation details and wiring diagram illustrations 07 007 A 6 ORAGE / white GREE / white Pair BUE/white & WHITE/blue 7 WHITE / brown BWHITE / brown Pair ORAGE/white C & WHITE/orange Pair GREE/white & WHITE/green D 8 BROW / white BROW / white Pair BROW/white & WHITE/brown 6 RJ Cat.e Euro - Angled K8 007 007 B C D E A B C D 6 6 7 8 7 6 RJ Cat.6 Screened K76S - JU6C, K86S - Euro 6 RJ Cat.e JU6C K7 0079 8 007 RJ Cat.6 Euro - Angled K76 - JU6C K86 - Euro, K - Euro Angled 8 7 6 RJ Cat.e Screened K8S - Euro
ogic Plus Technical 7 technical hotline + (0)68 670 white wiring devices Telephone, RJ/, BC Data and Blank Modules Telephone sockets K80 and K8 comply with the following: BS 6:. Data sockets K80, BS 7: 00 (where applicable). K887 complies with FCC68 and E 00. Cable types: Telephone: CW, CW9, CW08, CW6 o. of cables per termination: Telephone: RJ/: BC 0 Ohms impedance cable RG8, RG, URM Belden 9907 Frequency range: BC connector: 0 to GHz Impedance: BC Connector: 0. nominal Termination type: Telephone module IDC BC module Crimped connection Temperature range: Ambient air 0 C to +60 C IPXD K80, K8, K80 and K787. IPX K80, K88, K and K70 Max. installation altitude: 000 metres A range of telephone, data and blank modules to fit Euro and J6UC front plates. BC Euro modules with a 0Ohm crimp connector suitable for use with RG8, URM, URM76 and Beldon 9907 type coaxial cables are also available. Installation (Telephone socket modules) Product performance, systems compatibility Master Sockets: For use as the first socket outlet on a direct exchange. They contain the required surge protector (for line protection against electrical surges) and ringing capacitor. Secondary Sockets: for use as extension sockets when connected on the same line as a Master Socket. Installation tools required IDC Connectors (telephone & RJ outlets) MK insertion tool ist o. 00AT. Wire pull-out force: 0. ewtons when installed correctly. Wiring regulation restrictions Domestic Installations: The total RE (Ring Equivalent umber) value of all telephone equipment connected on a line must not exceed. Features Meet all relevant BS, OFTE and cabling standards Interchangeable modules clip into frontplates Front fixing facilitates easy exchange of modules Part of a complete range of products for telephone and data processing requirements Telephone sockets 00% tested before delivery Quick, simple and reliable IDC connectors Can be specified for all applications Data sockets atest specification for high performance systems Made to stringent quality assurance procedures Wide range of data connectors available For information on TV Satellite and FM Modules see pages -
8 ogic Plus Technical C D A E B F C G wiring devices white www.mkelectric.co.uk Telephone, A RJ/, BC B Data and CBlank Modules D E Telephone Wiring Scheme GREE / white BUE / white ORAGE / white WHITE / orange WHITE / blue 6 WHITE / green ote: Main wire colour is shown in capitals 6 6 007 0070 007 007 First Socket Outlet Extension Outlet 7 8 Master 6 Secondary 6 6 6 K80 6 K8 7 8 C D E F G H 0070 007 007 6 6 6 RJ/ Wiring Scheme PI STRIPPED COOUR SOID COOUR O. WIRE WIRE 0078 0078 0079 C 6 WHITE / green WHITE WHITE / orange BACK 7 BUE / white RED 8 6 6 6 WHITE / blue GREE 6 ORAGE / white YEOW MODIFICATIO TEXT: R MK EECTRIC (MAAYSIA) SD. BHD DIMESIOS AD TOERACES PER 6 GREE / white BUE C/O SYMPHOY CORPORATEHOUSE SD.BHD BRITISH STADARDS AD D FOOR, MEARA EO BAK ECC EGIEERIG STADARDS 88, JAA RAJA AUT ote: Main wire colour is shown 00 KUAA UMPUR MATERIA TITE in capitals007 K787 007 007 HOEYWE COFIDETIA AD PROPRIETARY K887 6 PROTECTED BY DI ISO 606 FIRST AGE PROJECTIO UITS DRAW BY: 0078 MM GEERA TOERACES: A B C IEAR ±0. HOE DIA ±0.08 RADII ±0.0 AGUAR ±0.0 FIISH MODIFICATIO TEXT: PACKAGIG SPEC o: PERMIT o: IMPRESSIOS: DRAW BY DATE: 6 SUB TITE DRAWIG o. R MK EECTRIC (MAAYSIA) SD. BHD C/O SYMPHOY CORPORATEHOUSE SD.BHD D FOOR, MEARA EO BAK PROJ 88, JAA O. RAJA AUT 00 KUAA UMPUR A B C 6 0079 8 UITS 6 8 MODIFICATIO TEXT: EVIROMETA & COMBU 0070,007,007,007,007 HOEYWE COFIDETIA AD PROPRIETARY PROTECTED BY DI ISO 606 FIRST AGE PROJECTIO DRAW BY: MM GEERA TOERACES: IEAR ±0. HOE DIA ±0.08 RADII ±0.0 AGUAR ±0.0 DIMESIOS AD TOERA BRITISH STADARDS ECC EGIEERIG PAPER SIZE STA MATERIA FIISH PACKAGIG SPEC o: PERMIT o: IMPRESSIOS: DRAW BY DATE: MODIFICATIO TEXT: R MK EECTRIC (MAAYSIA) SD. BHD C/O SYMPHOY CORPORATEHOUSE SD.BHD D FOOR, MEARA EO BAK 88, JAA RAJA AUT DIMESIOS AD TOERACES PER BRITISH STADARDS AD ECC EGIEERIG STADARDS EVIROMETA & COMBUSTIO COTROS
ogic Plus Technical 9 technical hotline + (0)68 670 white wiring devices MK Modular Datacoms ogic Plus Telephone and Data sockets comply with the following: Telephone sockets K0 and K BS 6:., OFTE Approval S/G///0000 Modular Frontplates K90 to K9 BS 7: 00 (where applicable) Cable types: Telephone CW, CW9, CW08, CW6 o. of cables per termination: Telephone: Termination type: RJ & Telephone - IDC Temperature range: Ambient air 0 C to +60 C IPXD A unique modular system in the distinctive ogic Plus style comprising a range of socket modules for Data and Telephone use, with matching frontplates capable of accepting combinations of interchangeable modules. The clip-in design provides a high degree of versatility, making the system ideal for use in all commercial and industrial applications. Features Meet all relevant BS, OFTE and cabling standards Interchangeable modules clip into frontplates Front fixing facilitates easy exchange of modules Part of a range of products for telephone and data processing requirements Quick, simple and reliable IDC connectors Can be specified for many applications Fit in plaster depth boxes Max. installation altitude: 000 metres BOX TYPES Where there is more than one module in a frontplate, the depth of the box is determined by the module with the deepest back projection. Min. box Flush box Surface box Ref. depth mm ist o. ist o. K0 6 99ZIC K60 & 6WHI K 6 99ZIC K60 & 6WHI K90 6 99ZIC K60 & 6WHI K87 6 99ZIC K60 & 6WHI Dimensions Data and TV modules (mm).. 8 8 K0 / K K90WHI
0 ogic Plus Technical wiring devices white www.mkelectric.co.uk MK Modular Datacoms Dimensions Modular frontplates (mm) 6 60. 0.6 K9 WHI K9 WHI 6 Installation (Telephone socket modules) Product performance, systems compatibility Master Sockets: For use as the first socket outlet on a direct exchange. They contain the required surge protector (for line protection against electrical surges) and ringing capacitor. Secondary Sockets: for use as extension sockets when connected on the same line as a Master Socket. Installation tools required IDC Connectors (Telephone & RJ outlets) MK insertion tool ist o. 00AT. Wire pull-out force: 0. ewtons when installed correctly. 60. K9 WHI K9 WHI 0.6 Wiring regulation restrictions Domestic Installations: The total RE (Ring Equivalent umber) value of all telephone equipment connected on a line must not exceed. Industrial and commercial installations: MK telephone sockets are suitable in all situations after the PBX/PABX has been installed by a recognised installer. For key systems and other special systems, the manufacturer s instructions should be referred to. RJ Wiring Scheme PI STRIPPED COOUR SOID COOUR O. WIRE WIRE WHITE / green White WHITE / orange Black BUE / white Red WHITE / blue Green ORAGE / white Yellow 6 GREE / white Blue ote: Main wire colour is shown in capitals 6 Rear View of Terminal Connection Block Safety information one of the above products should be installed into the same fixing or mounting boxes as mains rated equipment or cable. Cable management ogic Plus Modular Data and Telephone Sockets can be mounted in a variety of MK trunking systems. See main catalogue for further details. BOTTOM
ogic Plus Technical technical hotline + (0)68 670 white wiring devices Telephone, TV/FM and Satellite Socket Outlets ogic Plus Telephone and TV sockets comply with the following: Telephone sockets K and K7 BS 6:., BS 7: 00 (where applicable). K87: BS 7: 00 (where applicable) and FCC68. TV sockets K0, K and K BS 0: Part : 977/IEC 69-: 977, BS7: 00 (where applicable) and IEC6, Cls 0., 0.. TV sockets K BS 7: 00 (where applicable). Telephone sockets, cable specification: CW, CW9, CW08, CW6 o. of cables per termination: Re-usability: >9 reterminations (should not be reterminated with smaller diameter wire) A part of the very wide range of products in the distinctive ogic Plus style to meet the latest technical requirements and the standards applicable to modern technology in the installation of telephone and television equipment. The master and secondary tele phone sockets K and K7 comply with relevant approvals for direct and indirect connections between a termination point of a public telecommunications system and any piece of approved tele commu ni cations apparatus. For applications requiring twin or dual telephone outlets, refer to Modular Data and Telephone Sockets. ogic Plus Telephone and TV sockets will fit in plaster depth boxes (except for RJ). The F-type Satellite Socket may be used for connection of CATV, MATV and satellite TV installations. Digital TV outlets are available. TV sockets: Cable specification: CT 00 or equivalent Any standard low-loss TV co-axial cable: Outside -8mm diameter, inner conductor 0.-mm diameter Insertion loss: Insertion loss data available on request F Type satellite socket (K), cable specification: Co-axial cable: inner core diameter 0.-.mm RJ (K87), Cable specification: Capable of taking 0.08 to 0.6mm solid or stranded cable Ambient air: 0 C to +60 C IPXD Max. installation altitude: 000 metres Features Single screw termination on TV outlets Protected, fully enclosed PCBs Meet all relevant BS requirements Attractive new easy-clean ogic Plus styling Quick, simple and reliable terminal connection IDC connectors on telephone outlets Part of a complete range of products for telephone, television and data processing requirements Angled connector on TV outlets Sockets fit in plaster depth boxes (except K87)
ogic Plus Technical wiring devices white www.mkelectric.co.uk Telephone, TV/FM and Satellite Socket Outlets Dimensions (mm) Typically Typically Installation (Telephone sockets) Product performance, systems compatibility Master Sockets: for use as the first socket outlet on a direct exchange or PABX line. They contain surge protector (for line protection against electrical surges) and ringing capacitor. Secondary Sockets: For use as extension sockets when connected on the same line as a Master Socket. Installation tools required MK IDC insertion tool ist o. 00AT (not supplied with product). 60. K0/K 60. K/K Typically 9 Wiring regulation restrictions Domestic installations: Any number of MK sockets may be installed thereafter, with a total RE (Ring Equivalent umber) value of all telephone equipment connected on a line not exceeding. Telephone Wiring Scheme GREE / white BUE / white ORAGE / white WHITE / orange WHITE / blue 6 WHITE / green ote: Main wire colour is shown in capitals 60. 0 IDC terminals 6 K Cable Tie fixing point Sectional drawings show the furthest projections from the back of the frontplate (wall surface), including a typical coaxial connector in the case of TV sockets. All units will fit in 6mm plaster depth boxes except for K87 (Western Telecom socket). BOX TYPES Flush Surface gang ZIC K0WHI First Socket Outlet Master Cable tie Extension Outlet Secondary 6 6
ogic Plus Technical technical hotline + (0)68 670 white wiring devices Telephone, TV/FM and Satellite Socket Outlets Installation (TV sockets) Product performance, systems compatibility FM DAB TV Isolated Outlets are intended for use where safety isolation (rated at 000V ac) is required to provide protection against faults occurring within any mains powered product used on different parts of the distribution system. They are not suitable for use in systems where DC signals are passed through the socket, (e.g. where masthead/headend equipment is controlled by receiver/ decoder equipment). TV DIST SAT Diplexer Outlets are used in distribution systems where both TV and FM band signals are combined on a single aerial downlead. The filtering in the diplexer separates the appropriate signals and feeds them through to the relevant output connection port. Cable Routing and Use of Cable Clamp Sharp bends in the cable must be avoided during installation. The single TV/ FM socket is fitted with a cable clamp that can be fixed on either side of the termination position to facilitate this. TV VID TV TV HI-FI SAT When tightening the screening braid clamps ensure that the cable is firmly gripped and that the inner insulation is not squashed flat beyond a slight oval shape. TV VID SKY/DIG Safety Information TV outlets or modules must not be installed in the same enclosure as equipment rated in excess of 0V, (e.g. mains rated A sockets or switches). Method of installation of TV and FM aerial connection by using MK co-axial socket outlet and only one downlead. Conventional distribution system for TV and FM signals using a single aerial downlead. The signals from the TV and FM aerials and the satellite dish are combined together using two products. The first combines the TV and FM signals and the second adds the Sky signal to the TV/FM signal and provides a DC control path to power the B unit on the satellite dish. (These products are not supplied by MK). The single aerial down lead feeds into the triplexer (black lines in wiring diagram). The separated satellite signal is then fed to the decoder. The decoded satellite signal is then fed into the VCR along with the TV signal from the Triplexer. The output signal from the VCR then feeds into the TV and also back to the single outlet and onto the distribution amplifier (black lines in wiring diagram). The single cable back-feed then feeds back to the input of a multi way distribution amplifier, (typically located in the loft or garage) (red lines in wiring diagram). Each individual output from the distribution amplifier is then fed to the individual rooms in the house to a standard TV (single or diplexer) outlet to which the TV/VCR and/or Hi-Fi can be connected (blue lines in wiring diagram).
ogic Plus Technical wiring devices white www.mkelectric.co.uk Digital TV, Radio and Telephone Outlets All ogic Plus TV Outlets comply with BS 7 and BS E 008 where applicable. Also IEC 69-, BS E 6069- and BS 6 part Modular products are Euro compatible. Single Outlets TV/FM IEC Male or Female SATF-Type DC-90MHz DC-.7GHz Diplexer and Triplexer products TV Diplexer: Triplexer: FM Diplexer: Triplexer: SAT Diplexer: Triplexer: -6MHz 70-MHz -6MHz 70-MHz 87.-08MHz 87.-08MHz n/a 90-00MHz TV/FM/DAB/SAT products for digital radio TV Diplexer: Triplexer: -6MHz 70-MHz -6MHz 70-MHz There are two ranges of diplexer and triplexer products, an established range suitable for VHF TV, and a range suitable for digital radio (DAB). Diplexer modules are for connecting to a single co-axial aerial down lead carrying combined TV and FM signals. The filtering in the diplexer splits out the appropriate signal and feeds it to the relevant output connection. A DC control path is provided in the TV signal path through the diplexer. Triplexer modules are for connecting to a single co-axial aerial down lead carrying combined TV, FM and SAT signals. The filtering in the triplexer splits out the appropriate signal and feeds it to the relevant output connection. A DC control path is provided in the SAT signal path through the triplexer. The quad outlet contains a triplexer together with a separate satellite output, for use with Sky+, or more complex installations. Telephone secondary outlets are provided on some products for connection of telephone or for interactive TV applications. FM/DAB Diplexer: Triplexer: SAT or SAT Diplexer: Triplexer: SAT 87.-0MHz 87.-0MHz n/a 90-00MHz Features on Isolated Fully screened Earth terminal provided on TV modules Selected products with BT secondary outlets for interactive TV applications Selected products with supplementary TV outlet for back-feed for further distribution Diplexer: Triplexer: n/a -00MHz Cable management ogic Plus TV outlets can be mounted in a variety of MK trunking systems. BOX TYPES Flush Flush (for Extra Surface Insulated Surface Metal wiring space) gang ZIC 6ZIC K0WHI K AM/KAM gang ZIC 8ZIC KWHI K AM/KAM Minimum recommended box depth mm ote: Edge mounted modular products require mm box
ogic Plus Technical technical hotline + (0)68 670 white wiring devices Digital TV, Radio and Telephone Outlets Dimensions (mm) gang (monobloc) dimensions (mm) FM TV 60. gang (monobloc) dimensions (mm) Installation When installing the TV co-axial cable ensure that all cable bends are smooth so that the inner insulation is not crushed or squashed, otherwise the TV signal quality may be affected. ot suitable for loop-in loop-out installations. Use CT00 cable (or equivalent). TV Co-axial cable stripping details 6. 6. In the event that the earth terminal is required to be used, the installer must ensure that a suitable earth conductor is present to connect to the earth terminal. (In the case of G products both TV modules should be earthed). In the event that the earth terminal is required to be used, the installer must ensure that a suitable earth conductor is present to connect to the earth terminal. (In the case of G products both TV modules should be earthed). Telephone Wiring Scheme FM TV 6 Screening braid to remain in place over the inner insulation Earth terminal GREE / white BUE / white ORAGE / white WHITE / orange WHITE / blue 6 WHITE / green SAT 0.6 Co-axial cable Cable clamping plate Foil EMC screening gasket Clamping plate fixing screws ote: Main wire colour is shown in capitals IDC terminals 6 Earth terminal Cable Tie fixing point Co-axial cable Clamping fixing screws Cable clamp View with cable clamp removed First Socket Outlet Master Cable tie Extension Outlet Secondary 6 6 Telephone Outlet Connection Carefully strip 0mm of the Telephone cable outer sheath to expose the inner insulated conductors. Using the insertion tool supplied, (MK ist no. 00AT) carefully push each lead into the appropriate IDC terminals according to the wiring colour code stated in the BT Wiring Scheme diagram. Pins and 6 are frequently unused, wire cable may be used in these installations. If an existing installation uses a different wiring colour code system, this should be retained on any new or extended installation. Additional secondary extension outlets should be wired in parallel with the existing installation via the IDC terminals, (i.e. pin to pin, pin to pin, etc).
6 ogic Plus Technical wiring devices white www.mkelectric.co.uk Grid Plus Front Plates BS 7: 00 Grid Plus is a comprehensive modular switching and monitoring system ideal for a variety of applications within the commercial, public and domestic sectors. Dimensions (mm) 6 6 module K6WHI K6GRA module K6WHI K6GRA module K6WHI K6GRA module K6WHI K6GRA 6 6 6 6 6 06 6 module K66WHI K66GRA 8 module K68WHI K68GRA module K69WHI
ogic Plus Technical 7 technical hotline + (0)68 670 white wiring devices ogic Plus Combination Plates /-gang Stacked Combination Plate Gang Plate The -gang Stacked Combination Plate carries x -gang A DP switched sockets, plus a Quad TV, FM/DAB, Satellite outlet, single TV (IEC Female) and an additional Telephone socket. Additionally, there is a -module Euro area capable of accommodating any additional telephone or media products from the Euro modular range. Frontplate The frontplate complies with the mechanical strength requirements of BS 7: 00. Switched socket specification Compliant to BS 6 Part : 99 Voltage rating 0V a.c. Current rating Amp per socket outlet Terminal capacity ive, eutral & Earth x.mm² x mm² x 6mm² (standard) Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) IPXD Max. installation altitude 000 metres Quad TV, FM/DAB, Satellite outlet & additional TV Socket TV/FM/DAB/SAT products for digital radio TV Diplexer: Triplexer: FM/DAB Diplexer: Triplexer: SAT or SAT Diplexer: Triplexer: SAT Diplexer: Triplexer: Telephone Socket As used on K66WHI -6MHz 70-MHz -6MHz 70-MHz 87.-0MHz 87.-0MHz n/a 90-00MHz n/a -00MHz -module Euro Housing This portion of the plate accepts up to x 0mm high by mm wide Euro modules. (00mm x 0mm aperture) Gang Plate The -gang Stacked Combination Plate carries a -gang A DP switched sockets and an additional -module Euro area capable of accommodating any additional telephone or media products from the Euro modular range. Frontplate The frontplate complies with the mechanical strength requirements of BS 7: 00. Switched socket specification Compliant to BS 6 Part : 99 Voltage rating 0V a.c. Current rating Amp per socket outlet Terminal capacity ive, eutral & Earth x.mm² x mm² x 6mm² (standard) Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) IPXD Max. installation altitude 000 metres ote Pre-configured back boxes available shall be used with these plates. These are 8ZIC, which is mm deep, and for greater wiring space 8ZIC, which is 7mm deep These back boxes should always be used to ensure alignment of the fixing screws is correct and proper segmentation between mains and low voltage products is maintained Mains operated products and extra low voltage modules must not be installed within the same front plate aperture. Refers to BS 767 IEE Wiring regulations for detail When removing the fixing screws and front plate from an installation to gain access to low voltage modules, please be aware that there will also be access to the mains supply ote Pre-configured back boxes available shall be used with these plates. These are 87ZIC, which is mm deep, and for greater wiring space 88ZIC, which is 7mm deep These back boxes should always be used to ensure alignment of the fixing screws is correct and proper segmentation between mains and low voltage products is maintained Mains operated products and extra low voltage modules must not be installed within the same front plate aperture. Refers to BS 767 IEE Wiring regulations for detail When removing the fixing screws and front plate from an installation to gain access to low voltage modules, please be aware that there will also be access to the mains supply
8 ogic Plus Technical wiring devices white www.mkelectric.co.uk Accessories SURFACE MOUTIG BOXES 6mm 0mm *mm 8mm 0mm mm *mm 8*mm mm Moulded Moulded Moulded PVC Moulded Steel Steel Steel Steel gang Sockets (A) K0 K8 K0 K0 K AM K AM gang Sockets K K8 K7 K AM K AM K00 gang Sockets K K8 A Round Pin Sockets K0 K8 K AM K AM A/A Round Pin Sockets K0 K8 K AM K AM RCD Sockets K7 K AM K AM K00 Filtered Sockets K7 K AM K AM K00 Connection Units K0 K8 K0 K0 K AM K AM 0A DP Switches K0 K8 K0 K0 K AM K AM K0 A DP Switch K0 K8 K0 K0 K AM K AM K0, K (CK & SH) K7 K AM K AM K0 K00 K060, K06 K7 K AM K00 K700 K0 K8 K0 K AM K AM K70 K7, & gang Switches K60 K0 K8 K0 K0 K AM K AM & 6 gang Switches K6 K K8 K7 K AM K AM K00 gang Architrave Switch K gang Architrave Switch K Dimmers using Pattress K0, K, K, K K60 K, K, K, K K60 Dimmers not using Pattress K0, K, K, K K0 K8 K0 K0 K, K, K, K K0 K8 K0 K AM K AM K9, K9 K0 K8 K0 K AM K AM K9, K9 K K8 K AM K AM K00 Data/Telecom Plates K60 K0 K8 K0 K AM K AM Dependent upon modules used * With conduit entry knockouts OTE: the size of cable should be taken into consideration when choosing box depth
ogic Plus Technical 9 technical hotline + (0)68 670 white wiring devices Accessories FUSH MOUTIG BOXES 6mm mm* 7mm* mm* mm 6mm* 7mm* mm gang Sockets (A) ZIC 6 ZIC K06 877 ZIC gang Sockets ZIC 8 ZIC K06 878 ZIC gang Sockets K A Round Pin Sockets 99 ZIC ZIC 6 ZIC K06 877 ZIC A/A Round Pin Sockets ZIC 6 ZIC K06 877 ZIC RCD Sockets 8 ZIC K06 878 ZIC Filtered Sockets 8 ZIC K06 878 ZIC Connection Units 6 ZIC K06 877 ZIC 0A DP Switches 6 ZIC K06 877 ZIC K0 A DP Switch 6 ZIC 877 ZIC K0, K (CK & SH) 8 ZIC K06 878 ZIC K0 K0 K06 877 ZIC K060, K06 8 ZIC K06 878 ZIC K0 K700 ZIC 6 ZIC K06 877 ZIC K70, & gang Switches 99 ZIC ZIC 6 ZIC K06 877 ZIC & 6 gang Switches ZIC 8 ZIC K06 gang Architrave Switch 9 ZIC gang Architrave Switch 9 ZIC Dimmers using Pattress K0, K, K, K 99 ZIC 878 ZIC K, K, K, K 99 ZIC 878 ZIC Dimmers not using Pattress K0, K, K, K ZIC 6 ZIC K06 877 ZIC K, K, K, K ZIC K06 877 ZIC K9 & K9 ZIC 6 ZIC K06 877 ZIC K9 & K9 ZIC 8 ZIC K06 878 ZIC Data/Telecom Plates ZIC 6 ZIC K06 877 ZIC K0 AM K0 AM Box supplied with accessory Dependent upon modules used * With conduit entry knockouts OTE: the size of cable should be taken into consideration when choosing box depth
60 Product Application www.mkelectric.co.uk Albany Plus one gang lockable socket brushed chrome Available on a worldwide basis, the MK Design Service is supported by a dedicated team to ensure the seamless delivery of your chosen products. To find out more visit www.mkelectric.co.uk