Technicalinformation Technicalinformation
technicalinformation SYSTEM 40C GENERAL GROPERTIES 1 Glazing: from 4 to 22 mm 2 E.P.D.M. Sealing Gasket 3 Efficent drainage of the vent section 4 Efficent chamber for pressure leveling which provides a better watertightness. 5 Central sealing gasket for a better wind and watertightness. 6 Proved drainage avoids infiltration of water under the central gasket. 7 Direct front chamber drainage. 8 Economic height: frame: 40mm vent: 45 mm 9 Alternatif conren cleats with pres and die cast corner joint 10 Acoustical gasket in E.P.D.M. 11 6060 / 6063 aluminium alloy 40C ALUminium 1 EURO groove I 40C PERImetric 1 Perimetric Groove suitable for 9 axus and 20 mm hinge 2 0915600 extruded joint is suitable for GU unijet D and Siegenia Aubi A 300 Euro Groove Section Multilock Section 40C ALUminium 40C PERImetric 04
technicalinformation 40C Cold window and door systems. Construction Depth Glazing * Window: Frame: 40 mmvent : 45 mm * Door: Frame: 66 mmvent :45 mm Glazing from 4 mm up to 22 mm with dry E.P.D.M. Gaskets. The choice of joints and glazing beads depends on the thickness of the glass. According to the tolerances of the glazing either a smaller or bigger joint and or glazing bead is used. Window types: inside, tilt and turn, double casement. Door types: inside door, outside door, double door, swinging door. Special Characteristics The structural profile walls have a nominal thickness of 1.2 to 1.3 mm. Curved and round windows possible. Special ventilation possibilities. Connections Gaskets Drainage Fitting and anchoring Die cast and also pres corner joints can apply for fixing corners. The transoms are fixed with screw through the outer frame. The central gasket ensures the window is wind and watertight over the complete surface. The acoustic gasket is uninterrupted. All window types must be equipped with a drainage system in the bottom profiles or the transoms. The windows and doors are fitted level and at perfectly right angles. The aluminium constructions are fixed to the brickwork in such a way that shrinkage or expansion of the building have no influence on the aluminium constructions. The aluminium profiles are made out of the alloy 6060 and 6063. The aluminium profiles have been extruded from the alloy AlMgSi 0.5F22 in according to the EN 12020. Tolerance are based on the standart EN 12020. Aluminium alloy Physical Properties 1. Density : 2.71 g / cm3 2. Elasticity module : 7000 kg / mm2 3. Resistance : 2650 kg / mm2 4. Melting point : 650 C 5. Coeffcient of expansion : 23x10 C 6. Thermal permeability : 0.48 cal / cm /s Mechanical Properties 1. Rupture strength : 23.9 kg / mm2 2. Elasticity limit : 19 kg / mm2 3. Hardness : 25 Brinell The profiles get a surface treatment as described further on.the colours of the profiles for the inside and outside are the same or different.the anodisation and enamel procedures are carried out under the responsibility of the systems supplier who offer. Surface Treatment Electrostatic Powder Coating "The thermal break allows all surface treatments when compounded.the enamel construction version has the QUALICOAT label. On average, the coating thickness is minimally 60 micron. The architect can choose from the standart range of colour of the system su" Anodised Construction Version The complete anodisation process takes place in accordance with the specifications of QUALANOD. This procedure has to be applied to all exterior joinery situated in the following zones: *In industrial or highly polluted zones. *In city centres or along busy roads. *Along railroads. *In swimming pools, laboratories, industrial buildings, etc. 05
technicalinformation Code Drawing Theoretical Weight kg/m Statics Covering Surface (cm) Jxx (cm4) Jyy (cm4) Inside Outside Code Drawing Theoretical Weight kg/m Statics Covering Surface (cm) Jxx (cm4) Jyy (cm4) Inside Outside 4030500 1.051 75.7 10.53 9.69 7.97 0721100 0.184 3.04 4040100 1.318 61.97 11.60 12.92 10.32 0730100 0.516 17.5 4040200 1.410 65.29 11.74 12.92 10.32 4050100 0.856 6.09 6.55 6.90 4040300 0.783 7.94 5.37 4.43 3.97 4050200 0.675 4.73 7.14 1.82 6.62 4040400 0.491 3.81 5.2 4050300 0.386 1.50 3.17 4040600 0.362 4.98 4050400 0.592 2.29 4.85 4040700 0.485 11.80 10127015 0.530 4.21 4.21 14.16 2010100 0.355 7.13 10134015 0.875 18.93 18.93 22.17 0721200 0.363 2.67 1.07 4050700 0.475 4.10 4.10 6.78 07
technicalinformation Code Drawing Theoretical Weight kg/m Statics Covering Surface (cm) Jxx (cm4) Jyy (cm4) Inside Outside Code Drawing Theoretical Weight kg/m Statics Covering Surface (cm) Jxx (cm4) Jyy (cm4) Inside Outside 4050800 0.370 1.35 2.18 3.44 0810700 0.261 4.02 4050900 0.777 17.91 17.92 11.53 0810800 0.269 4.23 4051000 0.446 2.50 2.34 0810900 0.279 4.52 0710100 0.237 3.80 0811000 0.264 4.08 0710200 0.325 6.86 0811100 0.217 3.98 0710300 0.490 6.86 0910100 2.570 0720100 0.119 1.67 0910300 3.702 0810100 0.217 2.71 0910500 5.473 0810200 0.223 3.02 08
technicalinformation perimetric profiles Code Drawing Theoretical Weight kg/m Statics Covering Surface (cm) Jxx (cm4) Jyy (cm4) Inside Outside Code Drawing Theoretical Weight kg/m Covering Statics Surface (cm) Jxx (cm4) Jyy (cm4) Inside Outside 4015100 0.877 7.35 8.84 4.65 7.47 4030200 0.831 6.07 11.04 4.08 9.27 4010300 0.701 5.94 6.40 4.13 6.77 4055100 0.852 5.93 6.50 1.40 7.44 4010600 0.723 6.19 6.83 4.23 6.87 0910200 2.995 4010400 1.031 17.61 11.54 4.13 8.64 0915600 5.101 4025100 0.927 8.89 9.15 5.96 6.96 4025200 0.996 10.11 14.54 7.09 5.90 4025300 1.139 12.68 31.75 8.99 9.54 4025400 1.139 11.75 31.75 7.39 11.63 4035100 0.973 7.31 13.09 5.07 9.70 09
Aluminiumprofiles Aluminiumprofiles
aluminiumprofiles 4010100 THEORETICAL WEIGHT kg/m 0.594 EXTRUDED CORNER JOINT A CC10126.5 DIECAST CORNER JOINT LC1127 B FUJI 2000 4010200 THEORETICAL WEIGHT kg/m 0.756 EXTRUDED CORNER JOINT A CC10126.5 DIECAST CORNER JOINT LC1127 B FUJI 2000 C MO 19 4010300 THEORETICAL WEIGHT kg/m 0.701 EXTRUDED CORNER JOINT A CC10326.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 12
aluminiumprofiles 4010600 THEORETICAL WEIGHT kg/m 0.723 EXTRUDED CORNER JOINT A CC10326.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 C MO 19 4010400 THEORETICAL WEIGHT kg/m 1.031 EXTRUDED CORNER JOINT A CC10326.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 13
aluminiumprofiles 4010500 THEORETICAL WEIGHT kg/m 1.786 EXTRUDED CORNER JOINT A CC10126.5 DIECAST CORNER JOINT LC1127 B FUJI 2000 4020100 THEORETICAL WEIGHT kg/m 0.786 EXTRUDED CORNER JOINT A CC10126.5 DIECAST CORNER JOINT LC1127 B FUJI 2000 C MO 20 14
aluminiumprofiles 4021000 THEORETICAL WEIGHT kg/m 1.029 EXTRUDED CORNER JOINT A CC10326.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 C MO 20 4030100 THEORETICAL WEIGHT kg/m 0.759 4030200 THEORETICAL WEIGHT kg/m 0.831 EXTRUDED CORNER JOINT A CC10326.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 17
aluminiumprofiles 4030300 THEORETICAL WEIGHT kg/m 0.927 4030400 THEORETICAL WEIGHT kg/m 1.019 4030500 THEORETICAL WEIGHT kg/m 1.051 18
aluminiumprofiles 4040100 THEORETICAL WEIGHT kg/m 1.318 4040200 THEORETICAL WEIGHT kg/m 1.410 4040300 THEORETICAL WEIGHT kg/m 0.738 19
aluminiumprofiles 4040400 THEORETICAL WEIGHT kg/m 0.491 4040600 THEORETICAL WEIGHT kg/m 0.362 CORNER JOINT A P 100.1 4040700 THEORETICAL WEIGHT kg/m 0.485 0721200 THEORETICAL WEIGHT kg/m 0.363 ADAPTER CUP EM07212 2010100 THEORETICAL WEIGHT kg/m 0.355 0730100 THEORETICAL WEIGHT kg/m 0.516 0721100 THEORETICAL WEIGHT kg/m 0.184 20
aluminiumprofiles 4050100 THEORETICAL WEIGHT kg/m 0.856 ADAPTER CUP EM40501 4050200 THEORETICAL WEIGHT kg/m 0.675 B FUJI 2000 4050300 THEORETICAL WEIGHT kg/m 0.386 21
aluminiumprofiles 4050400 THEORETICAL WEIGHT kg/m 0.592 10127015 THEORETICAL WEIGHT kg/m 0.530 10134015 THEORETICAL WEIGHT kg/m 0.875 22
aluminiumprofiles 4050700 THEORETICAL WEIGHT kg/m 0.475 4050800 THEORETICAL WEIGHT kg/m 0.370 4050900 THEORETICAL WEIGHT kg/m 0.777 23
aluminiumprofiles 4051000 THEORETICAL WEIGHT kg/m 0.446 0710100 THEORETICAL WEIGHT kg/m 0.237 CORNER JOINT A M0 19 0710200 THEORETICAL WEIGHT kg/m 0.325 CORNER JOINT A MO 20.1 0710300 THEORETICAL WEIGHT kg/m 0.490 0720100 THEORETICAL WEIGHT kg/m 0.119 CORNER JOINT A MO 20.1 24
aluminiumprofiles 0810100 THEORETICAL WEIGHT kg/m 0.217 0810200 THEORETICAL WEIGHT kg/m 0.223 0810700 THEORETICAL WEIGHT kg/m 0.261 0810800 THEORETICAL WEIGHT kg/m 0.269 0810900 THEORETICAL WEIGHT kg/m 0.279 25
aluminiumprofiles 0811000 THEORETICAL WEIGHT kg/m 0.264 0811100 THEORETICAL WEIGHT kg/m 0.217 PVC ADAPTER EM08111 0910100 THEORETICAL WEIGHT kg/m 2.570 No visible surface. 26
aluminiumprofiles 0910300 THEORETICAL WEIGHT kg/m 3.702 No visible surface. 0910500 THEORETICAL WEIGHT kg/m 5.473 No visible surface. 27
Perimetricprofiles Perimetricprofiles
perimetricprofiles 4015100 THEORETICAL WEIGHT kg/m 0.877 EXTRUDED CORNER JOINT A CC10126.5 DIECAST CORNER JOINT LC1127 B FUJI 2000 4010300 THEORETICAL WEIGHT kg/m 0.701 EXTRUDED CORNER JOINT A CC15626.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 4010600 THEORETICAL WEIGHT kg/m 0.723 EXTRUDED CORNER JOINT A CC15626.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 C MO 19 30
perimetricprofiles 4010400 THEORETICAL WEIGHT kg/m 1.031 EXTRUDED CORNER JOINT A CC15626.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 4025100 THEORETICAL WEIGHT kg/m 0.927 EXTRUDED CORNER JOINT A CC10226.5 DIECAST CORNER JOINT LC1327 B FUJI 2000 C MO 20 4025200 THEORETICAL WEIGHT kg/m 0.996 EXTRUDED CORNER JOINT A CC15626.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 C MO 20 31
perimetricprofiles 4025300 THEORETICAL WEIGHT kg/m 1.139 EXTRUDED CORNER JOINT A CC10526.5 DIECAST CORNER JOINT LC4327 B FUJI 2000 C MO 20 4025400 THEORETICAL WEIGHT kg/m 1.139 EXTRUDED CORNER JOINT A CC10526.5 DIECAST CORNER JOINT LC4327 B FUJI 2000 C MO 20 4035100 THEORETICAL WEIGHT kg/m 0.973 32
perimetricprofiles 4030200 THEORETICAL WEIGHT kg/m 0.831 EXTRUDED CORNER JOINT A CC15626.5 DIECAST CORNER JOINT LC2327 B FUJI 2000 4055100 THEORETICAL WEIGHT kg/m 0.852 ADAPTER CUP EM40551 0910200 THEORETICAL WEIGHT kg/m 2.995 No visible surface. 33
perimetricprofiles No visible surface. 0915600 THEORETICAL WEIGHT kg/m 5.101 34
C M Y CM MY CY CMY K Aluminiumdetails Aluminiumdetails
C M Y CM MY CY CMY K aluminiumdetails 36
C M Y CM MY CY CMY K aluminiumdetails 37
C M Y CM MY CY CMY K aluminiumdetails 38
C M Y CM MY CY CMY K aluminiumdetails 39
C M Y CM MY CY CMY K aluminiumdetails 40
C M Y CM MY CY CMY K aluminiumdetails 41
C M Y CM MY CY CMY K aluminiumdetails 42
C M Y CM MY CY CMY K aluminiumdetails 43
C M Y CM MY CY CMY K aluminiumdetails Inside Opening Door Outside Opening Door 44
C M Y CM MY CY CMY K aluminiumdetails Inside Opening Door Outside Opening Door 45
C M Y CM MY CY CMY K aluminiumdetails Inside Opening Door Outside Opening Door 46
C M Y CM MY CY CMY K aluminiumdetails Inside Opening Door Outside Opening Door 47
C M Y CM MY CY CMY K aluminiumdetails Outside Opening Door 48
C M Y CM MY CY CMY K aluminiumdetails 49
C M Y CM MY CY CMY K aluminiumdetails Inside Opening Door Outside Opening Door 50
aluminiumdetails Inside Opening Door Outside Opening Door 51
aluminiumdetails Outside Opening Door 52
aluminiumdetails Inside Opening Door Outside Opening Door 53
aluminiumdetails Outside Opening Door Inside Opening Door 54
aluminiumdetails Outside Opening Door Inside Opening Door 55
aluminiumdetails Inside Opening Door Outside Opening Door 56
aluminiumdetails 57
58 aluminiumdetails
aluminiumdetails 59
60 aluminiumdetails
aluminiumdetails 61
62 aluminiumdetails
aluminiumdetails 63
Perimetricdetails Perimetricdetails
66 perimetricdetails
perimetricdetails 67
68 perimetricdetails
perimetricdetails Inside Opening Door Outside Opening Door 69
perimetricdetails Inside Opening Door Outside Opening Door 70
perimetricdetails Inside Opening Door Outside Opening Door 71
perimetricdetails Inside Opening Door Outside Opening Door 72
perimetricdetails Inside Opening Door 73
perimetricdetails Outside Opening Door Inside Opening Door 74
perimetricdetails Outside Opening Door Inside Opening Door 75
perimetricdetails Inside Opening Door Outside Opening Door 76
Glazingtable Glazingtable
GLAZING THICKNESS GLAZING GASKET INSIDE GLAZING GASKET OUTSIDE GLAZING BEAD 4 mm EM103 EM201 0810900 4 mm EM103 EM201 0811000 4 mm EM103 EM201 0811100 5 mm EM102 EM201 0810900 5 mm EM102 EM201 0811000 5 mm EM102 EM201 0811100 78
glazingtable GLAZING THICKNESS GLAZING GASKET INSIDE GLAZING GASKET OUTSIDE GLAZING BEAD 6 mm EM104 EM201 0810800 8 mm EM104 EM201 0810700 10 mm EM102 EM201 0810700 20 mm EM102 EM201 0810200 22 mm EM102 EM201 0810100 79
Accessories Accessories
accessories DRAW NG APLICATION DESCRIPTION THEORETICAL WEIGHT kg/m IN ONE PACKAGE EM102 Glazing Gasket Inside (EPDM) 0.050 300 m EM103 Glazing Gasket Inside (EPDM) 0.060 250 m EM104 Glazing Gasket Inside (EPDM) 0.070 215 m EM201 Glazing Gasket Outside (EPDM) 0.055 270 m EM301 Acoustical Gasket (EPDM) 0.032 465 m EM4001 Central Gasket (EPDM) 0.115 130 m 82
accessories ACCESSORY DRAW NG APLICATION PROFILES APPLICATION PROFILES EM40501 4050100 ALUminium EM40551 4055100 PERImetric EM07212 0721200 EM08111 0811100 EM15200 ROD PROFILE (Euro Section 1) EM1001 (White) EM1002 (Black) Drainage Cap EM1003 (Brown) 83
84 accessories ACCESSORY DRAW NG APLICATION PROFILES APPLICATION PROFILES LC1127 4010100 4010200 4010500 4015100 4020100 4020200 4025100 4010300 4010400 4010600 4020300 4020600 4020900 4021000 4025200 4030200 4020400 4020500 4025300 4025400 4010100 4010200 4010300 4010400 4010500 4010600 4015100 4020100 4020300 4020400 4020500 4021000 4025100 4025200 4025300 4025400 4030200 4050200 LC1327 LC2327 LC4327 FUJI 2000
accessories ACCESSORY DRAW NG APLICATION PROFILES APPLICATION PROFILES 4020100 4020200 4020300 4020400 4020500 MO 20 4020600 4020900 4021000 4025100 4025200 4025300 4025400 P 101.1 4040600 MO 19 4010200 4010600 0710100 MO 20.1 0710200 0710300 85
accessories PROFILE DRAW NG PACKAGE QUANTITY CUTTING SIZE APPLICATION PROFILES APPLICATION DETAIL 4010100 4010200 0910100 CC10126.5 60 pieces 26.5 mm 4010500 4015100 4020100 4020200 0910200 CC10226.5 60 pieces 26.5 mm 4025100 4010300 4010400 4010600 0910300 CC10326.5 50 pieces 26.5 mm 4020300 4020600 4020900 4021000 4030200 4020400 0910500 CC10526.5 25 pieces 26.5 mm 4020500 4025300 4025400 Special Extruded Corner Joint for Perimetric 0915600 CC15626.5 25 pieces 26.5 mm 4010300 4010400 4010600 4025200 4030200 86
accessories System 40C, 54T and 60T Use this tool 40C profiles without 4010500 profile Lorenzoline Punching Machine Handle Slot Produche Code LC0101 Indent Rod Profile Groove For (EM15200) Arm Drain Hole System 40C, 54T and 60T System 40C, 54T and 60T Use this tool 40C profiles without 4010500 profile System 40C, 54T and 60T Arm Drain Hole Handle Slot Arm System 40C, 54T and 60T Indent Rod Profile Groove System 40C, 54T and 60T Arm 87
Cuttingsizes Cuttingsizes
cuttingsizes Accessories Quantity (pcsm) View Profile Cut Quantity (pcs) Dimensions (mm) CC10126.5/LC 1127 8 pcs 4010100 4020100 2 pcs 2 pcs 2 pcs 2 pcs L H Lv=L(A1+A1)+12 Hv=H(A1+A1)+12 FUJI 2000 MO 20 EM4001 EM103 8 pcs 4 pcs 2 Lv + 2 Hv 2 Lg + 2 Hg 0810200 2 pcs 2 pcs Lg=Lv(A2+A2) Hg=Hv(A2+A2+22+22) EM201 EM301 2 Lg + 2 Hg (Lv + Hv) x 4 90
cuttingsizes Profile Cut Quantity (pcs) Dimensions (mm) 4010100 4020100 4050100 0810200 2 pcs 2 pcs 4 pcs 4 pcs 1 pcs 2 pcs 2 pcs L H L(A1+A1)+7 Lv= 2 Hv=H(A1+A1)+12 Ah= Hv70 Lg=Lv(A2+A2) Hg=Hv(A2+A2+22+22) Accessories Quantity (pcsm) View CC10126.5/LC 1127 FUJI 2000 MO 20 EM40501 EM4001 EM103 EM201 EM301 12 pcs 12 pcs 8 pcs 1 set 4 Lv + 3 Hv 4 Lg + 4 Hg 4 Lg + 4 Hg 4 Lv + 8 Hv 91
cuttingsizes Profile Cut Quantity (pcs) Dimensions (mm) 4010300 4020400 0810200 4030300 4040300 4040600 0721200 1 pcs 1 pcs 1 pcs 2 pcs 2 pcs 2 pcs 2 pcs 1 pcs 1 pcs 1 pcs 1 pcs L H H Lv=L(A1+A1)+12 Hv=H(A1)+1 Lg=Lv(A2+A2) Hg=Hv(A2+A2+22+22) Lg=Lv(A2+A2) Lg=Lv(A2+A2) L1=L(A1+A1) Ah=Hv70 Accessories Quantity (pcsm) View CC10326.5/LC 2327 CC10526.5/LC 4327 FUJI 2000 MO 20 P 100.1 EM07212 EM4001 EM103 EM201 EM301 BRUSH 10 2 pcs 4 pcs 6 pcs 4 pcs 2 pcs 1 set 1 Lv + 2 Hv 4 Lg + 4 Hg 4 Lg + 4 Hg 4 Lv + 4 Hv A3 92
cuttingsizes Profile Cut Quantity (pcs) Dimensions (mm) 4010300 4020500 0810900 4050100 4040100 2010100 1 pcs 1 pcs 1 pcs 2 pcs 2 pcs 2 pcs 4 pcs 4 pcs 1 pcs 2 pcs 1 pcs L H H L(A1+A1)+7 Lv= 2 Hv=HA16 Hv=HA16 Lg=Lv(A2+A2) Hg=Hv(A2+142) Ah=Hv3512 Lg=Lv(A2+A2) L1=L(A1+A1) Accessories Quantity (pcsm) View CC10326.5/LC 2327 CC10526.5/LC 4327 FUJI 2000 MO 20 P 100.1 EM40501 EM4001 EM103 EM201 EM301 BRUSH 10 2 pcs 4 pcs 10 pcs 8 pcs 2 pcs 1 set 2 Lv + 3 Hv 4 Lg + 4 Hg 4 Lg + 4 Hg 4 Lv + 6 Lv L1 93
cuttingsizes Profile Cut Quantity (pcs) Dimensions (mm) 4010300 4030200 4051000 0810200 4040300 1 pcs 1 pcs 1 pcs 4 pcs 4 pcs 1 pcs 4 pcs 1 pcs 1 pcs 4 pcs 4 pcs 4 pcs 2 pcs L H H L2A183 Lv= 2 Hv=H(A1+43) La=L(A1+A1)+9.8 L2A183 Lv= 2 Ha=HA1+4.9 Ha=HA1+4.9 Hv=H(A1+43) Lg=Lv114.8 Hg=Hv198.2 Lg=Lv114.8 Accessories Quantity (pcsm) View CC10326.5/LC 2327 FUJI 2000 EM103 EM201 BRUSH 10 10 pcs 10 pcs 4 Lg + 4 Hg 4 Lg + 4 Hg 12 Lv + 12 Hv + 78 94
Assemblydrawings Assemblydrawings
assemblydrawings Corner Connection With Extruded Corner Joint Corner Connection With DieCast Corner Joint 96
assemblydrawings Aluminium Two Sash Window & Door Cap Assembly 97
assemblydrawings Perimetric Two Sash Window & Door Cap Assembly 98
assemblydrawings Mullion Connection Assembly 99
100 assemblydrawings
assemblydrawings Mullion Cutting Knife Detail 101
assemblydrawings Glazing Bead Corner Types 102